13 files changed, 663 insertions, 594 deletions

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index c89fafc972b6..6ee55a2d47bb 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -201,8 +201,31 @@ static unsigned int dw8250_serial_in32be(struct uart_port *p, int offset)
 
 static int dw8250_handle_irq(struct uart_port *p)
 {
+	struct uart_8250_port *up = up_to_u8250p(p);
 	struct dw8250_data *d = p->private_data;
 	unsigned int iir = p->serial_in(p, UART_IIR);
+	unsigned int status;
+	unsigned long flags;
+
+	/*
+	 * There are ways to get Designware-based UARTs into a state where
+	 * they are asserting UART_IIR_RX_TIMEOUT but there is no actual
+	 * data available.  If we see such a case then we'll do a bogus
+	 * read.  If we don't do this then the "RX TIMEOUT" interrupt will
+	 * fire forever.
+	 *
+	 * This problem has only been observed so far when not in DMA mode
+	 * so we limit the workaround only to non-DMA mode.
+	 */
+	if (!up->dma && ((iir & 0x3f) == UART_IIR_RX_TIMEOUT)) {
+		spin_lock_irqsave(&p->lock, flags);
+		status = p->serial_in(p, UART_LSR);
+
+		if (!(status & (UART_LSR_DR | UART_LSR_BI)))
+			(void) p->serial_in(p, UART_RX);
+
+		spin_unlock_irqrestore(&p->lock, flags);
+	}
 
 	if (serial8250_handle_irq(p, iir))
 		return 1;
@@ -248,11 +271,11 @@ static void dw8250_set_termios(struct uart_port *p, struct ktermios *termios,
 	if (!ret)
 		p->uartclk = rate;
 
+out:
 	p->status &= ~UPSTAT_AUTOCTS;
 	if (termios->c_cflag & CRTSCTS)
 		p->status |= UPSTAT_AUTOCTS;
 
-out:
 	serial8250_do_set_termios(p, termios, old);
 }
 
@@ -326,13 +349,11 @@ static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 			p->serial_in = dw8250_serial_in32;
 			data->uart_16550_compatible = true;
 		}
-		p->set_termios = dw8250_set_termios;
 	}
 
 	/* Platforms with iDMA */
 	if (platform_get_resource_byname(to_platform_device(p->dev),
 					 IORESOURCE_MEM, "lpss_priv")) {
-		p->set_termios = dw8250_set_termios;
 		data->dma.rx_param = p->dev->parent;
 		data->dma.tx_param = p->dev->parent;
 		data->dma.fn = dw8250_idma_filter;
@@ -414,6 +435,7 @@ static int dw8250_probe(struct platform_device *pdev)
 	p->serial_in	= dw8250_serial_in;
 	p->serial_out	= dw8250_serial_out;
 	p->set_ldisc	= dw8250_set_ldisc;
+	p->set_termios	= dw8250_set_termios;
 
 	p->membase = devm_ioremap(dev, regs->start, resource_size(regs));
 	if (!p->membase)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
new file mode 100644
index 000000000000..b89c4ffc0486
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -0,0 +1,487 @@
+/*
+ *  Probe module for 8250/16550-type Exar chips PCI serial ports.
+ *
+ *  Based on drivers/tty/serial/8250/8250_pci.c,
+ *
+ *  Copyright (C) 2017 Sudip Mukherjee, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/tty.h>
+#include <linux/8250_pci.h>
+
+#include <asm/byteorder.h>
+
+#include "8250.h"
+
+#define PCI_DEVICE_ID_COMMTECH_4224PCI335	0x0002
+#define PCI_DEVICE_ID_COMMTECH_4222PCI335	0x0004
+#define PCI_DEVICE_ID_COMMTECH_2324PCI335	0x000a
+#define PCI_DEVICE_ID_COMMTECH_2328PCI335	0x000b
+#define PCI_DEVICE_ID_COMMTECH_4224PCIE		0x0020
+#define PCI_DEVICE_ID_COMMTECH_4228PCIE		0x0021
+#define PCI_DEVICE_ID_COMMTECH_4222PCIE		0x0022
+#define PCI_DEVICE_ID_EXAR_XR17V4358		0x4358
+#define PCI_DEVICE_ID_EXAR_XR17V8358		0x8358
+
+#define UART_EXAR_8XMODE	0x88	/* 8X sampling rate select */
+
+#define UART_EXAR_FCTR		0x08	/* Feature Control Register */
+#define UART_FCTR_EXAR_IRDA	0x10	/* IrDa data encode select */
+#define UART_FCTR_EXAR_485	0x20	/* Auto 485 half duplex dir ctl */
+#define UART_FCTR_EXAR_TRGA	0x00	/* FIFO trigger table A */
+#define UART_FCTR_EXAR_TRGB	0x60	/* FIFO trigger table B */
+#define UART_FCTR_EXAR_TRGC	0x80	/* FIFO trigger table C */
+#define UART_FCTR_EXAR_TRGD	0xc0	/* FIFO trigger table D programmable */
+
+#define UART_EXAR_TXTRG		0x0a	/* Tx FIFO trigger level write-only */
+#define UART_EXAR_RXTRG		0x0b	/* Rx FIFO trigger level write-only */
+
+#define UART_EXAR_MPIOINT_7_0	0x8f	/* MPIOINT[7:0] */
+#define UART_EXAR_MPIOLVL_7_0	0x90	/* MPIOLVL[7:0] */
+#define UART_EXAR_MPIO3T_7_0	0x91	/* MPIO3T[7:0] */
+#define UART_EXAR_MPIOINV_7_0	0x92	/* MPIOINV[7:0] */
+#define UART_EXAR_MPIOSEL_7_0	0x93	/* MPIOSEL[7:0] */
+#define UART_EXAR_MPIOOD_7_0	0x94	/* MPIOOD[7:0] */
+#define UART_EXAR_MPIOINT_15_8	0x95	/* MPIOINT[15:8] */
+#define UART_EXAR_MPIOLVL_15_8	0x96	/* MPIOLVL[15:8] */
+#define UART_EXAR_MPIO3T_15_8	0x97	/* MPIO3T[15:8] */
+#define UART_EXAR_MPIOINV_15_8	0x98	/* MPIOINV[15:8] */
+#define UART_EXAR_MPIOSEL_15_8	0x99	/* MPIOSEL[15:8] */
+#define UART_EXAR_MPIOOD_15_8	0x9a	/* MPIOOD[15:8] */
+
+struct exar8250;
+
+/**
+ * struct exar8250_board - board information
+ * @num_ports: number of serial ports
+ * @reg_shift: describes UART register mapping in PCI memory
+ */
+struct exar8250_board {
+	unsigned int num_ports;
+	unsigned int reg_shift;
+	bool has_slave;
+	int	(*setup)(struct exar8250 *, struct pci_dev *,
+			 struct uart_8250_port *, int);
+	void	(*exit)(struct pci_dev *pcidev);
+};
+
+struct exar8250 {
+	unsigned int		nr;
+	struct exar8250_board	*board;
+	int			line[0];
+};
+
+static int default_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+			 int idx, unsigned int offset,
+			 struct uart_8250_port *port)
+{
+	const struct exar8250_board *board = priv->board;
+	unsigned int bar = 0;
+
+	if (!pcim_iomap_table(pcidev)[bar] && !pcim_iomap(pcidev, bar, 0))
+		return -ENOMEM;
+
+	port->port.iotype = UPIO_MEM;
+	port->port.mapbase = pci_resource_start(pcidev, bar) + offset;
+	port->port.membase = pcim_iomap_table(pcidev)[bar] + offset;
+	port->port.regshift = board->reg_shift;
+
+	return 0;
+}
+
+static int
+pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		     struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 1843200;
+	u8 __iomem *p;
+	int err;
+
+	port->port.flags |= UPF_EXAR_EFR;
+	port->port.uartclk = baud * 16;
+
+	err = default_setup(priv, pcidev, idx, offset, port);
+	if (err)
+		return err;
+
+	p = port->port.membase;
+
+	writeb(0x00, p + UART_EXAR_8XMODE);
+	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+	writeb(32, p + UART_EXAR_TXTRG);
+	writeb(32, p + UART_EXAR_RXTRG);
+
+	/*
+	 * Setup Multipurpose Input/Output pins.
+	 */
+	if (idx == 0) {
+		switch (pcidev->device) {
+		case PCI_DEVICE_ID_COMMTECH_4222PCI335:
+		case PCI_DEVICE_ID_COMMTECH_4224PCI335:
+			writeb(0x78, p + UART_EXAR_MPIOLVL_7_0);
+			writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+			writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+			break;
+		case PCI_DEVICE_ID_COMMTECH_2324PCI335:
+		case PCI_DEVICE_ID_COMMTECH_2328PCI335:
+			writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+			writeb(0xc0, p + UART_EXAR_MPIOINV_7_0);
+			writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0);
+			break;
+		}
+		writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+		writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+		writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+	}
+
+	return 0;
+}
+
+static int
+pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		       struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 1843200;
+
+	port->port.uartclk = baud * 16;
+	return default_setup(priv, pcidev, idx, offset, port);
+}
+
+static int
+pci_xr17c154_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		   struct uart_8250_port *port, int idx)
+{
+	unsigned int offset = idx * 0x200;
+	unsigned int baud = 921600;
+
+	port->port.uartclk = baud * 16;
+	return default_setup(priv, pcidev, idx, offset, port);
+}
+
+static void setup_gpio(u8 __iomem *p)
+{
+	writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+	writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+	writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
+	writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
+	writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
+}
+
+static void *
+xr17v35x_register_gpio(struct pci_dev *pcidev)
+{
+	struct platform_device *pdev;
+
+	pdev = platform_device_alloc("gpio_exar", PLATFORM_DEVID_AUTO);
+	if (!pdev)
+		return NULL;
+
+	platform_set_drvdata(pdev, pcidev);
+	if (platform_device_add(pdev) < 0) {
+		platform_device_put(pdev);
+		return NULL;
+	}
+
+	return pdev;
+}
+
+static int
+pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+		   struct uart_8250_port *port, int idx)
+{
+	const struct exar8250_board *board = priv->board;
+	unsigned int offset = idx * 0x400;
+	unsigned int baud = 7812500;
+	u8 __iomem *p;
+	int ret;
+
+	port->port.uartclk = baud * 16;
+	/*
+	 * Setup the uart clock for the devices on expansion slot to
+	 * half the clock speed of the main chip (which is 125MHz)
+	 */
+	if (board->has_slave && idx >= 8)
+		port->port.uartclk /= 2;
+
+	ret = default_setup(priv, pcidev, idx, offset, port);
+	if (ret)
+		return ret;
+
+	p = port->port.membase;
+
+	writeb(0x00, p + UART_EXAR_8XMODE);
+	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+	writeb(128, p + UART_EXAR_TXTRG);
+	writeb(128, p + UART_EXAR_RXTRG);
+
+	if (idx == 0) {
+		/* Setup Multipurpose Input/Output pins. */
+		setup_gpio(p);
+
+		port->port.private_data = xr17v35x_register_gpio(pcidev);
+	}
+
+	return 0;
+}
+
+static void pci_xr17v35x_exit(struct pci_dev *pcidev)
+{
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	struct uart_8250_port *port = serial8250_get_port(priv->line[0]);
+	struct platform_device *pdev = port->port.private_data;
+
+	platform_device_unregister(pdev);
+	port->port.private_data = NULL;
+}
+
+static int
+exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
+{
+	unsigned int nr_ports, i, bar = 0, maxnr;
+	struct exar8250_board *board;
+	struct uart_8250_port uart;
+	struct exar8250 *priv;
+	int rc;
+
+	board = (struct exar8250_board *)ent->driver_data;
+	if (!board)
+		return -EINVAL;
+
+	rc = pcim_enable_device(pcidev);
+	if (rc)
+		return rc;
+
+	maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3);
+
+	nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
+
+	priv = devm_kzalloc(&pcidev->dev, sizeof(*priv) +
+			    sizeof(unsigned int) * nr_ports,
+			    GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->board = board;
+
+	pci_set_master(pcidev);
+
+	rc = pci_alloc_irq_vectors(pcidev, 1, 1, PCI_IRQ_ALL_TYPES);
+	if (rc < 0)
+		return rc;
+
+	memset(&uart, 0, sizeof(uart));
+	uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ
+			  | UPF_EXAR_EFR;
+	uart.port.irq = pci_irq_vector(pcidev, 0);
+	uart.port.dev = &pcidev->dev;
+
+	for (i = 0; i < nr_ports && i < maxnr; i++) {
+		rc = board->setup(priv, pcidev, &uart, i);
+		if (rc) {
+			dev_err(&pcidev->dev, "Failed to setup port %u\n", i);
+			break;
+		}
+
+		dev_dbg(&pcidev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
+			uart.port.iobase, uart.port.irq, uart.port.iotype);
+
+		priv->line[i] = serial8250_register_8250_port(&uart);
+		if (priv->line[i] < 0) {
+			dev_err(&pcidev->dev,
+				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
+				uart.port.iobase, uart.port.irq,
+				uart.port.iotype, priv->line[i]);
+			break;
+		}
+	}
+	priv->nr = i;
+	pci_set_drvdata(pcidev, priv);
+	return 0;
+}
+
+static void exar_pci_remove(struct pci_dev *pcidev)
+{
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		serial8250_unregister_port(priv->line[i]);
+
+	if (priv->board->exit)
+		priv->board->exit(pcidev);
+}
+
+static int __maybe_unused exar_suspend(struct device *dev)
+{
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		if (priv->line[i] >= 0)
+			serial8250_suspend_port(priv->line[i]);
+
+	/* Ensure that every init quirk is properly torn down */
+	if (priv->board->exit)
+		priv->board->exit(pcidev);
+
+	return 0;
+}
+
+static int __maybe_unused exar_resume(struct device *dev)
+{
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	struct exar8250 *priv = pci_get_drvdata(pcidev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++)
+		if (priv->line[i] >= 0)
+			serial8250_resume_port(priv->line[i]);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
+
+static const struct exar8250_board pbn_fastcom335_2 = {
+	.num_ports	= 2,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_fastcom335_4 = {
+	.num_ports	= 4,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_fastcom335_8 = {
+	.num_ports	= 8,
+	.setup		= pci_fastcom335_setup,
+};
+
+static const struct exar8250_board pbn_connect = {
+	.setup		= pci_connect_tech_setup,
+};
+
+static const struct exar8250_board pbn_exar_ibm_saturn = {
+	.num_ports	= 1,
+	.setup		= pci_xr17c154_setup,
+};
+
+static const struct exar8250_board pbn_exar_XR17C15x = {
+	.setup		= pci_xr17c154_setup,
+};
+
+static const struct exar8250_board pbn_exar_XR17V35x = {
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V4358 = {
+	.num_ports	= 12,
+	.has_slave	= true,
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_exar_XR17V8358 = {
+	.num_ports	= 16,
+	.has_slave	= true,
+	.setup		= pci_xr17v35x_setup,
+	.exit		= pci_xr17v35x_exit,
+};
+
+#define CONNECT_DEVICE(devid, sdevid, bd) {				\
+	PCI_DEVICE_SUB(							\
+		PCI_VENDOR_ID_EXAR,					\
+		PCI_DEVICE_ID_EXAR_##devid,				\
+		PCI_SUBVENDOR_ID_CONNECT_TECH,				\
+		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0,	\
+		(kernel_ulong_t)&bd					\
+	}
+
+#define EXAR_DEVICE(vend, devid, bd) {					\
+	PCI_VDEVICE(vend, PCI_DEVICE_ID_##devid), (kernel_ulong_t)&bd	\
+	}
+
+#define IBM_DEVICE(devid, sdevid, bd) {			\
+	PCI_DEVICE_SUB(					\
+		PCI_VENDOR_ID_EXAR,			\
+		PCI_DEVICE_ID_EXAR_##devid,		\
+		PCI_VENDOR_ID_IBM,			\
+		PCI_SUBDEVICE_ID_IBM_##sdevid), 0, 0,	\
+		(kernel_ulong_t)&bd			\
+	}
+
+static struct pci_device_id exar_pci_tbl[] = {
+	CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_2, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8, pbn_connect),
+	CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect),
+	CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect),
+	CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect),
+
+	IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn),
+
+	/* Exar Corp. XR17C15[248] Dual/Quad/Octal UART */
+	EXAR_DEVICE(EXAR, EXAR_XR17C152, pbn_exar_XR17C15x),
+	EXAR_DEVICE(EXAR, EXAR_XR17C154, pbn_exar_XR17C15x),
+	EXAR_DEVICE(EXAR, EXAR_XR17C158, pbn_exar_XR17C15x),
+
+	/* Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */
+	EXAR_DEVICE(EXAR, EXAR_XR17V352, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V354, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V358, pbn_exar_XR17V35x),
+	EXAR_DEVICE(EXAR, EXAR_XR17V4358, pbn_exar_XR17V4358),
+	EXAR_DEVICE(EXAR, EXAR_XR17V8358, pbn_exar_XR17V8358),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4222PCIE, pbn_exar_XR17V35x),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4224PCIE, pbn_exar_XR17V35x),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4228PCIE, pbn_exar_XR17V35x),
+
+	EXAR_DEVICE(COMMTECH, COMMTECH_4222PCI335, pbn_fastcom335_2),
+	EXAR_DEVICE(COMMTECH, COMMTECH_4224PCI335, pbn_fastcom335_4),
+	EXAR_DEVICE(COMMTECH, COMMTECH_2324PCI335, pbn_fastcom335_4),
+	EXAR_DEVICE(COMMTECH, COMMTECH_2328PCI335, pbn_fastcom335_8),
+	{ 0, }
+};
+MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
+
+static struct pci_driver exar_pci_driver = {
+	.name		= "exar_serial",
+	.probe		= exar_pci_probe,
+	.remove		= exar_pci_remove,
+	.driver         = {
+		.pm     = &exar_pci_pm,
+	},
+	.id_table	= exar_pci_tbl,
+};
+module_pci_driver(exar_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Exar Serial Dricer");
+MODULE_AUTHOR("Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>");
diff --git a/drivers/tty/serial/8250/8250_gsc.c b/drivers/tty/serial/8250/8250_gsc.c
index b1e6ae9f1ff9..63306de4390d 100644
--- a/drivers/tty/serial/8250/8250_gsc.c
+++ b/drivers/tty/serial/8250/8250_gsc.c
@@ -60,6 +60,10 @@ static int __init serial_init_chip(struct parisc_device *dev)
 					7272727 : 1843200;
 	uart.port.mapbase	= address;
 	uart.port.membase	= ioremap_nocache(address, 16);
+	if (!uart.port.membase) {
+		dev_warn(&dev->dev, "Failed to map memory\n");
+		return -ENOMEM;
+	}
 	uart.port.irq	= dev->irq;
 	uart.port.flags	= UPF_BOOT_AUTOCONF;
 	uart.port.dev	= &dev->dev;
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 38166db2b824..115190b7962a 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -19,7 +19,7 @@
 
 #include "8250.h"
 
-#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI)
+#if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI) && !defined(CONFIG_COMPILE_TEST)
 #warning CONFIG_SERIAL_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
 #endif
 
diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index 58cbb30a9401..f3ea90f0e411 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -332,10 +332,10 @@ static void lpss8250_remove(struct pci_dev *pdev)
 {
 	struct lpss8250 *lpss = pci_get_drvdata(pdev);
 
+	serial8250_unregister_port(lpss->line);
+
 	if (lpss->board->exit)
 		lpss->board->exit(lpss);
-
-	serial8250_unregister_port(lpss->line);
 }
 
 static const struct lpss8250_board byt_board = {
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index ac013edf4992..ec957cce8c9a 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -75,6 +75,37 @@ static int pnw_setup(struct mid8250 *mid, struct uart_port *p)
 	return 0;
 }
 
+static int tng_handle_irq(struct uart_port *p)
+{
+	struct mid8250 *mid = p->private_data;
+	struct uart_8250_port *up = up_to_u8250p(p);
+	struct hsu_dma_chip *chip;
+	u32 status;
+	int ret = 0;
+	int err;
+
+	chip = pci_get_drvdata(mid->dma_dev);
+
+	/* Rx DMA */
+	err = hsu_dma_get_status(chip, mid->dma_index * 2 + 1, &status);
+	if (err > 0) {
+		serial8250_rx_dma_flush(up);
+		ret |= 1;
+	} else if (err == 0)
+		ret |= hsu_dma_do_irq(chip, mid->dma_index * 2 + 1, status);
+
+	/* Tx DMA */
+	err = hsu_dma_get_status(chip, mid->dma_index * 2, &status);
+	if (err > 0)
+		ret |= 1;
+	else if (err == 0)
+		ret |= hsu_dma_do_irq(chip, mid->dma_index * 2, status);
+
+	/* UART */
+	ret |= serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+	return IRQ_RETVAL(ret);
+}
+
 static int tng_setup(struct mid8250 *mid, struct uart_port *p)
 {
 	struct pci_dev *pdev = to_pci_dev(p->dev);
@@ -90,6 +121,8 @@ static int tng_setup(struct mid8250 *mid, struct uart_port *p)
 
 	mid->dma_index = index;
 	mid->dma_dev = pci_get_slot(pdev->bus, PCI_DEVFN(5, 0));
+
+	p->handle_irq = tng_handle_irq;
 	return 0;
 }
 
@@ -131,8 +164,16 @@ static int dnv_setup(struct mid8250 *mid, struct uart_port *p)
 	unsigned int bar = FL_GET_BASE(mid->board->flags);
 	int ret;
 
+	pci_set_master(pdev);
+
+	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
+	if (ret < 0)
+		return ret;
+
+	p->irq = pci_irq_vector(pdev, 0);
+
 	chip->dev = &pdev->dev;
-	chip->irq = pdev->irq;
+	chip->irq = pci_irq_vector(pdev, 0);
 	chip->regs = p->membase;
 	chip->length = pci_resource_len(pdev, bar);
 	chip->offset = DNV_DMA_CHAN_OFFSET;
@@ -250,8 +291,6 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (ret)
 		return ret;
 
-	pci_set_master(pdev);
-
 	mid = devm_kzalloc(&pdev->dev, sizeof(*mid), GFP_KERNEL);
 	if (!mid)
 		return -ENOMEM;
diff --git a/drivers/tty/serial/8250/8250_moxa.c b/drivers/tty/serial/8250/8250_moxa.c
index 26eb5393a263..d5069b2d4d79 100644
--- a/drivers/tty/serial/8250/8250_moxa.c
+++ b/drivers/tty/serial/8250/8250_moxa.c
@@ -68,6 +68,7 @@ static int moxa8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 			   sizeof(unsigned int) * nr_ports, GFP_KERNEL);
 	if (!brd)
 		return -ENOMEM;
+	brd->num_ports = nr_ports;
 
 	memset(&uart, 0, sizeof(struct uart_8250_port));
 
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index d25ab1cd4295..1cbadafc6889 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -172,7 +172,8 @@ static int of_platform_serial_probe(struct platform_device *ofdev)
 {
 	const struct of_device_id *match;
 	struct of_serial_info *info;
-	struct uart_port port;
+	struct uart_8250_port port8250;
+	u32 tx_threshold;
 	int port_type;
 	int ret;
 
@@ -188,41 +189,24 @@ static int of_platform_serial_probe(struct platform_device *ofdev)
 		return -ENOMEM;
 
 	port_type = (unsigned long)match->data;
-	ret = of_platform_serial_setup(ofdev, port_type, &port, info);
+	memset(&port8250, 0, sizeof(port8250));
+	ret = of_platform_serial_setup(ofdev, port_type, &port8250.port, info);
 	if (ret)
 		goto out;
 
-	switch (port_type) {
-	case PORT_8250 ... PORT_MAX_8250:
-	{
-		u32 tx_threshold;
-		struct uart_8250_port port8250;
-		memset(&port8250, 0, sizeof(port8250));
-		port8250.port = port;
+	if (port8250.port.fifosize)
+		port8250.capabilities = UART_CAP_FIFO;
 
-		if (port.fifosize)
-			port8250.capabilities = UART_CAP_FIFO;
+	/* Check for TX FIFO threshold & set tx_loadsz */
+	if ((of_property_read_u32(ofdev->dev.of_node, "tx-threshold",
+				  &tx_threshold) == 0) &&
+	    (tx_threshold < port8250.port.fifosize))
+		port8250.tx_loadsz = port8250.port.fifosize - tx_threshold;
 
-		/* Check for TX FIFO threshold & set tx_loadsz */
-		if ((of_property_read_u32(ofdev->dev.of_node, "tx-threshold",
-					  &tx_threshold) == 0) &&
-		    (tx_threshold < port.fifosize))
-			port8250.tx_loadsz = port.fifosize - tx_threshold;
+	if (of_property_read_bool(ofdev->dev.of_node, "auto-flow-control"))
+		port8250.capabilities |= UART_CAP_AFE;
 
-		if (of_property_read_bool(ofdev->dev.of_node,
-					  "auto-flow-control"))
-			port8250.capabilities |= UART_CAP_AFE;
-
-		ret = serial8250_register_8250_port(&port8250);
-		break;
-	}
-	default:
-		/* need to add code for these */
-	case PORT_UNKNOWN:
-		dev_info(&ofdev->dev, "Unknown serial port found, ignored\n");
-		ret = -ENODEV;
-		break;
-	}
+	ret = serial8250_register_8250_port(&port8250);
 	if (ret < 0)
 		goto out;
 
@@ -232,7 +216,7 @@ static int of_platform_serial_probe(struct platform_device *ofdev)
 	return 0;
 out:
 	kfree(info);
-	irq_dispose_mapping(port.irq);
+	irq_dispose_mapping(port8250.port.irq);
 	return ret;
 }
 
@@ -242,14 +226,8 @@ out:
 static int of_platform_serial_remove(struct platform_device *ofdev)
 {
 	struct of_serial_info *info = platform_get_drvdata(ofdev);
-	switch (info->type) {
-	case PORT_8250 ... PORT_MAX_8250:
-		serial8250_unregister_port(info->line);
-		break;
-	default:
-		/* need to add code for these */
-		break;
-	}
+
+	serial8250_unregister_port(info->line);
 
 	if (info->clk)
 		clk_disable_unprepare(info->clk);
@@ -258,18 +236,23 @@ static int of_platform_serial_remove(struct platform_device *ofdev)
 }
 
 #ifdef CONFIG_PM_SLEEP
-static void of_serial_suspend_8250(struct of_serial_info *info)
+static int of_serial_suspend(struct device *dev)
 {
+	struct of_serial_info *info = dev_get_drvdata(dev);
 	struct uart_8250_port *port8250 = serial8250_get_port(info->line);
 	struct uart_port *port = &port8250->port;
 
 	serial8250_suspend_port(info->line);
+
 	if (info->clk && (!uart_console(port) || console_suspend_enabled))
 		clk_disable_unprepare(info->clk);
+
+	return 0;
 }
 
-static void of_serial_resume_8250(struct of_serial_info *info)
+static int of_serial_resume(struct device *dev)
 {
+	struct of_serial_info *info = dev_get_drvdata(dev);
 	struct uart_8250_port *port8250 = serial8250_get_port(info->line);
 	struct uart_port *port = &port8250->port;
 
@@ -277,34 +260,6 @@ static void of_serial_resume_8250(struct of_serial_info *info)
 		clk_prepare_enable(info->clk);
 
 	serial8250_resume_port(info->line);
-}
-
-static int of_serial_suspend(struct device *dev)
-{
-	struct of_serial_info *info = dev_get_drvdata(dev);
-
-	switch (info->type) {
-	case PORT_8250 ... PORT_MAX_8250:
-		of_serial_suspend_8250(info);
-		break;
-	default:
-		break;
-	}
-
-	return 0;
-}
-
-static int of_serial_resume(struct device *dev)
-{
-	struct of_serial_info *info = dev_get_drvdata(dev);
-
-	switch (info->type) {
-	case PORT_8250 ... PORT_MAX_8250:
-		of_serial_resume_8250(info);
-		break;
-	default:
-		break;
-	}
 
 	return 0;
 }
@@ -332,6 +287,7 @@ static const struct of_device_id of_platform_serial_table[] = {
 		.data = (void *)PORT_ALTR_16550_F128, },
 	{ .compatible = "mrvl,mmp-uart",
 		.data = (void *)PORT_XSCALE, },
+	{ .compatible = "ti,da830-uart", .data = (void *)PORT_DA830, },
 	{ /* end of list */ },
 };
 MODULE_DEVICE_TABLE(of, of_platform_serial_table);
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 61ad6c3b20a0..e7e64913a748 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -790,6 +790,7 @@ static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
 {
 	struct omap8250_priv	*priv = p->port.private_data;
 	struct uart_8250_dma	*dma = p->dma;
+	struct dma_tx_state     state;
 	unsigned long		flags;
 	int ret;
 
@@ -800,10 +801,12 @@ static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
 		return;
 	}
 
-	ret = dmaengine_pause(dma->rxchan);
-	if (WARN_ON_ONCE(ret))
-		priv->rx_dma_broken = true;
-
+	ret = dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
+	if (ret == DMA_IN_PROGRESS) {
+		ret = dmaengine_pause(dma->rxchan);
+		if (WARN_ON_ONCE(ret))
+			priv->rx_dma_broken = true;
+	}
 	spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
 
 	__dma_rx_do_complete(p);
@@ -1075,15 +1078,15 @@ static int omap8250_no_handle_irq(struct uart_port *port)
 }
 
 static const u8 am3352_habit = OMAP_DMA_TX_KICK | UART_ERRATA_CLOCK_DISABLE;
-static const u8 am4372_habit = UART_ERRATA_CLOCK_DISABLE;
+static const u8 dra742_habit = UART_ERRATA_CLOCK_DISABLE;
 
 static const struct of_device_id omap8250_dt_ids[] = {
 	{ .compatible = "ti,omap2-uart" },
 	{ .compatible = "ti,omap3-uart" },
 	{ .compatible = "ti,omap4-uart" },
 	{ .compatible = "ti,am3352-uart", .data = &am3352_habit, },
-	{ .compatible = "ti,am4372-uart", .data = &am4372_habit, },
-	{ .compatible = "ti,dra742-uart", .data = &am4372_habit, },
+	{ .compatible = "ti,am4372-uart", .data = &am3352_habit, },
+	{ .compatible = "ti,dra742-uart", .data = &dra742_habit, },
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap8250_dt_ids);
@@ -1218,14 +1221,6 @@ static int omap8250_probe(struct platform_device *pdev)
 			priv->omap8250_dma.rx_size = RX_TRIGGER;
 			priv->omap8250_dma.rxconf.src_maxburst = RX_TRIGGER;
 			priv->omap8250_dma.txconf.dst_maxburst = TX_TRIGGER;
-
-			if (of_machine_is_compatible("ti,am33xx"))
-				priv->habit |= OMAP_DMA_TX_KICK;
-			/*
-			 * pause is currently not supported atleast on omap-sdma
-			 * and edma on most earlier kernels.
-			 */
-			priv->rx_dma_broken = true;
 		}
 	}
 #endif
@@ -1240,7 +1235,8 @@ static int omap8250_probe(struct platform_device *pdev)
 	pm_runtime_put_autosuspend(&pdev->dev);
 	return 0;
 err:
-	pm_runtime_put(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	return ret;
 }
@@ -1249,6 +1245,7 @@ static int omap8250_remove(struct platform_device *pdev)
 {
 	struct omap8250_priv *priv = platform_get_drvdata(pdev);
 
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	serial8250_unregister_port(priv->line);
@@ -1348,6 +1345,10 @@ static int omap8250_runtime_suspend(struct device *dev)
 	struct omap8250_priv *priv = dev_get_drvdata(dev);
 	struct uart_8250_port *up;
 
+	/* In case runtime-pm tries this before we are setup */
+	if (!priv)
+		return 0;
+
 	up = serial8250_get_port(priv->line);
 	/*
 	 * When using 'no_console_suspend', the console UART must not be
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 116436b7fa52..00e51a064388 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1477,11 +1477,16 @@ static int pci_fintek_init(struct pci_dev *dev)
 {
 	unsigned long iobase;
 	u32 max_port, i;
-	u32 bar_data[3];
+	resource_size_t bar_data[3];
 	u8 config_base;
 	struct serial_private *priv = pci_get_drvdata(dev);
 	struct uart_8250_port *port;
 
+	if (!(pci_resource_flags(dev, 5) & IORESOURCE_IO) ||
+			!(pci_resource_flags(dev, 4) & IORESOURCE_IO) ||
+			!(pci_resource_flags(dev, 3) & IORESOURCE_IO))
+		return -ENODEV;
+
 	switch (dev->device) {
 	case 0x1104: /* 4 ports */
 	case 0x1108: /* 8 ports */
@@ -1495,9 +1500,9 @@ static int pci_fintek_init(struct pci_dev *dev)
 	}
 
 	/* Get the io address dispatch from the BIOS */
-	pci_read_config_dword(dev, 0x24, &bar_data[0]);
-	pci_read_config_dword(dev, 0x20, &bar_data[1]);
-	pci_read_config_dword(dev, 0x1c, &bar_data[2]);
+	bar_data[0] = pci_resource_start(dev, 5);
+	bar_data[1] = pci_resource_start(dev, 4);
+	bar_data[2] = pci_resource_start(dev, 3);
 
 	for (i = 0; i < max_port; ++i) {
 		/* UART0 configuration offset start from 0x40 */
@@ -1605,135 +1610,6 @@ static int pci_eg20t_init(struct pci_dev *dev)
 #endif
 }
 
-#define PCI_DEVICE_ID_EXAR_XR17V4358	0x4358
-#define PCI_DEVICE_ID_EXAR_XR17V8358	0x8358
-
-#define UART_EXAR_MPIOINT_7_0	0x8f	/* MPIOINT[7:0] */
-#define UART_EXAR_MPIOLVL_7_0	0x90	/* MPIOLVL[7:0] */
-#define UART_EXAR_MPIO3T_7_0	0x91	/* MPIO3T[7:0] */
-#define UART_EXAR_MPIOINV_7_0	0x92	/* MPIOINV[7:0] */
-#define UART_EXAR_MPIOSEL_7_0	0x93	/* MPIOSEL[7:0] */
-#define UART_EXAR_MPIOOD_7_0	0x94	/* MPIOOD[7:0] */
-#define UART_EXAR_MPIOINT_15_8	0x95	/* MPIOINT[15:8] */
-#define UART_EXAR_MPIOLVL_15_8	0x96	/* MPIOLVL[15:8] */
-#define UART_EXAR_MPIO3T_15_8	0x97	/* MPIO3T[15:8] */
-#define UART_EXAR_MPIOINV_15_8	0x98	/* MPIOINV[15:8] */
-#define UART_EXAR_MPIOSEL_15_8	0x99	/* MPIOSEL[15:8] */
-#define UART_EXAR_MPIOOD_15_8	0x9a	/* MPIOOD[15:8] */
-
-static int
-pci_xr17c154_setup(struct serial_private *priv,
-		  const struct pciserial_board *board,
-		  struct uart_8250_port *port, int idx)
-{
-	port->port.flags |= UPF_EXAR_EFR;
-	return pci_default_setup(priv, board, port, idx);
-}
-
-static inline int
-xr17v35x_has_slave(struct serial_private *priv)
-{
-	const int dev_id = priv->dev->device;
-
-	return ((dev_id == PCI_DEVICE_ID_EXAR_XR17V4358) ||
-		(dev_id == PCI_DEVICE_ID_EXAR_XR17V8358));
-}
-
-static int
-pci_xr17v35x_setup(struct serial_private *priv,
-		  const struct pciserial_board *board,
-		  struct uart_8250_port *port, int idx)
-{
-	u8 __iomem *p;
-
-	p = pci_ioremap_bar(priv->dev, 0);
-	if (p == NULL)
-		return -ENOMEM;
-
-	port->port.flags |= UPF_EXAR_EFR;
-
-	/*
-	 * Setup the uart clock for the devices on expansion slot to
-	 * half the clock speed of the main chip (which is 125MHz)
-	 */
-	if (xr17v35x_has_slave(priv) && idx >= 8)
-		port->port.uartclk = (7812500 * 16 / 2);
-
-	/*
-	 * Setup Multipurpose Input/Output pins.
-	 */
-	if (idx == 0) {
-		writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
-		writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
-		writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
-		writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
-		writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
-		writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
-		writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
-	}
-	writeb(0x00, p + UART_EXAR_8XMODE);
-	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
-	writeb(128, p + UART_EXAR_TXTRG);
-	writeb(128, p + UART_EXAR_RXTRG);
-	iounmap(p);
-
-	return pci_default_setup(priv, board, port, idx);
-}
-
-#define PCI_DEVICE_ID_COMMTECH_4222PCI335 0x0004
-#define PCI_DEVICE_ID_COMMTECH_4224PCI335 0x0002
-#define PCI_DEVICE_ID_COMMTECH_2324PCI335 0x000a
-#define PCI_DEVICE_ID_COMMTECH_2328PCI335 0x000b
-
-static int
-pci_fastcom335_setup(struct serial_private *priv,
-		  const struct pciserial_board *board,
-		  struct uart_8250_port *port, int idx)
-{
-	u8 __iomem *p;
-
-	p = pci_ioremap_bar(priv->dev, 0);
-	if (p == NULL)
-		return -ENOMEM;
-
-	port->port.flags |= UPF_EXAR_EFR;
-
-	/*
-	 * Setup Multipurpose Input/Output pins.
-	 */
-	if (idx == 0) {
-		switch (priv->dev->device) {
-		case PCI_DEVICE_ID_COMMTECH_4222PCI335:
-		case PCI_DEVICE_ID_COMMTECH_4224PCI335:
-			writeb(0x78, p + UART_EXAR_MPIOLVL_7_0);
-			writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
-			writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
-			break;
-		case PCI_DEVICE_ID_COMMTECH_2324PCI335:
-		case PCI_DEVICE_ID_COMMTECH_2328PCI335:
-			writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
-			writeb(0xc0, p + UART_EXAR_MPIOINV_7_0);
-			writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0);
-			break;
-		}
-		writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
-		writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
-		writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
-	}
-	writeb(0x00, p + UART_EXAR_8XMODE);
-	writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
-	writeb(32, p + UART_EXAR_TXTRG);
-	writeb(32, p + UART_EXAR_RXTRG);
-	iounmap(p);
-
-	return pci_default_setup(priv, board, port, idx);
-}
-
 static int
 pci_wch_ch353_setup(struct serial_private *priv,
 		    const struct pciserial_board *board,
@@ -1809,9 +1685,6 @@ pci_wch_ch38x_setup(struct serial_private *priv,
 #define PCI_VENDOR_ID_AGESTAR		0x5372
 #define PCI_DEVICE_ID_AGESTAR_9375	0x6872
 #define PCI_VENDOR_ID_ASIX		0x9710
-#define PCI_DEVICE_ID_COMMTECH_4224PCIE	0x0020
-#define PCI_DEVICE_ID_COMMTECH_4228PCIE	0x0021
-#define PCI_DEVICE_ID_COMMTECH_4222PCIE	0x0022
 #define PCI_DEVICE_ID_BROADCOM_TRUMANAGE 0x160a
 #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800 0x818e
 
@@ -2273,65 +2146,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.setup		= pci_timedia_setup,
 	},
 	/*
-	 * Exar cards
-	 */
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17C152,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17c154_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17C154,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17c154_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17C158,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17c154_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17V352,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17V354,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17V358,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17V4358,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_EXAR,
-		.device = PCI_DEVICE_ID_EXAR_XR17V8358,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	/*
 	 * Xircom cards
 	 */
 	{
@@ -2556,59 +2370,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.setup		= pci_asix_setup,
 	},
 	/*
-	 * Commtech, Inc. Fastcom adapters
-	 *
-	 */
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_4222PCI335,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fastcom335_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_4224PCI335,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fastcom335_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_2324PCI335,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fastcom335_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_2328PCI335,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_fastcom335_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_4222PCIE,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_4224PCIE,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	{
-		.vendor = PCI_VENDOR_ID_COMMTECH,
-		.device = PCI_DEVICE_ID_COMMTECH_4228PCIE,
-		.subvendor	= PCI_ANY_ID,
-		.subdevice	= PCI_ANY_ID,
-		.setup		= pci_xr17v35x_setup,
-	},
-	/*
 	 * Broadcom TruManage (NetXtreme)
 	 */
 	{
@@ -2719,17 +2480,11 @@ enum pci_board_num_t {
 
 	pbn_b0_4_1152000,
 
-	pbn_b0_2_1152000_200,
-	pbn_b0_4_1152000_200,
-	pbn_b0_8_1152000_200,
+	pbn_b0_4_1250000,
 
 	pbn_b0_2_1843200,
 	pbn_b0_4_1843200,
 
-	pbn_b0_2_1843200_200,
-	pbn_b0_4_1843200_200,
-	pbn_b0_8_1843200_200,
-
 	pbn_b0_1_4000000,
 
 	pbn_b0_bt_1_115200,
@@ -2820,15 +2575,6 @@ enum pci_board_num_t {
 	pbn_computone_6,
 	pbn_computone_8,
 	pbn_sbsxrsio,
-	pbn_exar_XR17C152,
-	pbn_exar_XR17C154,
-	pbn_exar_XR17C158,
-	pbn_exar_XR17V352,
-	pbn_exar_XR17V354,
-	pbn_exar_XR17V358,
-	pbn_exar_XR17V4358,
-	pbn_exar_XR17V8358,
-	pbn_exar_ibm_saturn,
 	pbn_pasemi_1682M,
 	pbn_ni8430_2,
 	pbn_ni8430_4,
@@ -2933,25 +2679,11 @@ static struct pciserial_board pci_boards[] = {
 		.uart_offset	= 8,
 	},
 
-	[pbn_b0_2_1152000_200] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 2,
-		.base_baud	= 1152000,
-		.uart_offset	= 0x200,
-	},
-
-	[pbn_b0_4_1152000_200] = {
+	[pbn_b0_4_1250000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 4,
-		.base_baud	= 1152000,
-		.uart_offset	= 0x200,
-	},
-
-	[pbn_b0_8_1152000_200] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 8,
-		.base_baud	= 1152000,
-		.uart_offset	= 0x200,
+		.base_baud	= 1250000,
+		.uart_offset	= 8,
 	},
 
 	[pbn_b0_2_1843200] = {
@@ -2967,24 +2699,6 @@ static struct pciserial_board pci_boards[] = {
 		.uart_offset	= 8,
 	},
 
-	[pbn_b0_2_1843200_200] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 2,
-		.base_baud	= 1843200,
-		.uart_offset	= 0x200,
-	},
-	[pbn_b0_4_1843200_200] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 4,
-		.base_baud	= 1843200,
-		.uart_offset	= 0x200,
-	},
-	[pbn_b0_8_1843200_200] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 8,
-		.base_baud	= 1843200,
-		.uart_offset	= 0x200,
-	},
 	[pbn_b0_1_4000000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
@@ -3469,76 +3183,6 @@ static struct pciserial_board pci_boards[] = {
 		.reg_shift	= 4,
 	},
 	/*
-	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
-	 *  Only basic 16550A support.
-	 *  XR17C15[24] are not tested, but they should work.
-	 */
-	[pbn_exar_XR17C152] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 2,
-		.base_baud	= 921600,
-		.uart_offset	= 0x200,
-	},
-	[pbn_exar_XR17C154] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 4,
-		.base_baud	= 921600,
-		.uart_offset	= 0x200,
-	},
-	[pbn_exar_XR17C158] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 8,
-		.base_baud	= 921600,
-		.uart_offset	= 0x200,
-	},
-	[pbn_exar_XR17V352] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 2,
-		.base_baud	= 7812500,
-		.uart_offset	= 0x400,
-		.reg_shift	= 0,
-		.first_offset	= 0,
-	},
-	[pbn_exar_XR17V354] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 4,
-		.base_baud	= 7812500,
-		.uart_offset	= 0x400,
-		.reg_shift	= 0,
-		.first_offset	= 0,
-	},
-	[pbn_exar_XR17V358] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 8,
-		.base_baud	= 7812500,
-		.uart_offset	= 0x400,
-		.reg_shift	= 0,
-		.first_offset	= 0,
-	},
-	[pbn_exar_XR17V4358] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 12,
-		.base_baud	= 7812500,
-		.uart_offset	= 0x400,
-		.reg_shift	= 0,
-		.first_offset	= 0,
-	},
-	[pbn_exar_XR17V8358] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 16,
-		.base_baud	= 7812500,
-		.uart_offset	= 0x400,
-		.reg_shift	= 0,
-		.first_offset	= 0,
-	},
-	[pbn_exar_ibm_saturn] = {
-		.flags		= FL_BASE0,
-		.num_ports	= 1,
-		.base_baud	= 921600,
-		.uart_offset	= 0x200,
-	},
-
-	/*
 	 * PA Semi PWRficient PA6T-1682M on-chip UART
 	 */
 	[pbn_pasemi_1682M] = {
@@ -3734,6 +3378,10 @@ static const struct pci_device_id blacklist[] = {
 	{ PCI_VDEVICE(INTEL, 0x228c), },
 	{ PCI_VDEVICE(INTEL, 0x9ce3), },
 	{ PCI_VDEVICE(INTEL, 0x9ce4), },
+
+	/* Exar devices */
+	{ PCI_VDEVICE(EXAR, PCI_ANY_ID), },
+	{ PCI_VDEVICE(COMMTECH, PCI_ANY_ID), },
 };
 
 /*
@@ -3908,7 +3556,7 @@ err_out:
 }
 EXPORT_SYMBOL_GPL(pciserial_init_ports);
 
-void pciserial_detach_ports(struct serial_private *priv)
+static void pciserial_detach_ports(struct serial_private *priv)
 {
 	struct pci_serial_quirk *quirk;
 	int i;
@@ -4159,58 +3807,6 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_VENDOR_ID_AFAVLAB,
 		PCI_SUBDEVICE_ID_AFAVLAB_P061, 0, 0,
 		pbn_b0_4_1152000 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_232, 0, 0,
-		pbn_b0_2_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_232, 0, 0,
-		pbn_b0_4_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_232, 0, 0,
-		pbn_b0_8_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_1_1, 0, 0,
-		pbn_b0_2_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_2, 0, 0,
-		pbn_b0_4_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4, 0, 0,
-		pbn_b0_8_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2, 0, 0,
-		pbn_b0_2_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4, 0, 0,
-		pbn_b0_4_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8, 0, 0,
-		pbn_b0_8_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_485, 0, 0,
-		pbn_b0_2_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_485, 0, 0,
-		pbn_b0_4_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
-		PCI_SUBVENDOR_ID_CONNECT_TECH,
-		PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_485, 0, 0,
-		pbn_b0_8_1843200_200 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_VENDOR_ID_IBM, PCI_SUBDEVICE_ID_IBM_SATURN_SERIAL_ONE_PORT,
-		0, 0, pbn_exar_ibm_saturn },
-
 	{	PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b2_bt_1_115200 },
@@ -4938,45 +4534,6 @@ static struct pci_device_id serial_pci_tbl[] = {
 	{	PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM8,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b3_8_115200 },
-
-	/*
-	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
-	 */
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17C152 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17C154 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17C158 },
-	/*
-	 * Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs
-	 */
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V352 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V354,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V354 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V358,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V358 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V4358,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V4358 },
-	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V8358 },
 	/*
 	 * Pericom PI7C9X795[1248] Uno/Dual/Quad/Octal UART
 	 */
@@ -5552,43 +5109,15 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_wch384_4 },
 
-	/*
-	 * Commtech, Inc. Fastcom adapters
-	 */
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4222PCI335,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_b0_2_1152000_200 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4224PCI335,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_b0_4_1152000_200 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_2324PCI335,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_b0_4_1152000_200 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_2328PCI335,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_b0_8_1152000_200 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4222PCIE,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V352 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4224PCIE,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V354 },
-	{	PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4228PCIE,
-		PCI_ANY_ID, PCI_ANY_ID,
-		0,
-		0, pbn_exar_XR17V358 },
-
 	/* Fintek PCI serial cards */
 	{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
 	{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
 	{ PCI_DEVICE(0x1c29, 0x1112), .driver_data = pbn_fintek_12 },
 
+	/* MKS Tenta SCOM-080x serial cards */
+	{ PCI_DEVICE(0x1601, 0x0800), .driver_data = pbn_b0_4_1250000 },
+	{ PCI_DEVICE(0x1601, 0xa801), .driver_data = pbn_b0_4_1250000 },
+
 	/*
 	 * These entries match devices with class COMMUNICATION_SERIAL,
 	 * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index c13fec451d03..6119516ef5fc 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -45,6 +45,12 @@
 #include "8250.h"
 
 /*
+ * These are definitions for the Exar XR17V35X and XR17(C|D)15X
+ */
+#define UART_EXAR_SLEEP		0x8b	/* Sleep mode */
+#define UART_EXAR_DVID		0x8d	/* Device identification */
+
+/*
  * Debugging.
  */
 #if 0
@@ -273,6 +279,15 @@ static const struct serial8250_config uart_config[] = {
 		.rxtrig_bytes	= {1, 4, 8, 14},
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_DA830] = {
+		.name		= "TI DA8xx/66AK2x",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
+				  UART_FCR_R_TRIG_10,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
 };
 
 /* Uart divisor latch read */
@@ -1753,8 +1768,6 @@ void serial8250_tx_chars(struct uart_8250_port *up)
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(port);
 
-	pr_debug("%s: THRE\n", __func__);
-
 	/*
 	 * With RPM enabled, we have to wait until the FIFO is empty before the
 	 * HW can go idle. So we get here once again with empty FIFO and disable
@@ -1819,8 +1832,6 @@ int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
 
 	status = serial_port_in(port, UART_LSR);
 
-	pr_debug("%s: status = %x\n", __func__, status);
-
 	if (status & (UART_LSR_DR | UART_LSR_BI)) {
 		if (!up->dma || handle_rx_dma(up, iir))
 			status = serial8250_rx_chars(up, status);
@@ -2118,6 +2129,19 @@ int serial8250_do_startup(struct uart_port *port)
 		serial_port_out(port, UART_LCR, 0);
 	}
 
+	if (port->type == PORT_DA830) {
+		/* Reset the port */
+		serial_port_out(port, UART_IER, 0);
+		serial_port_out(port, UART_DA830_PWREMU_MGMT, 0);
+		mdelay(10);
+
+		/* Enable Tx, Rx and free run mode */
+		serial_port_out(port, UART_DA830_PWREMU_MGMT,
+				UART_DA830_PWREMU_MGMT_UTRST |
+				UART_DA830_PWREMU_MGMT_URRST |
+				UART_DA830_PWREMU_MGMT_FREE);
+	}
+
 #ifdef CONFIG_SERIAL_8250_RSA
 	/*
 	 * If this is an RSA port, see if we can kick it up to the
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 0b8b6740ba43..a65fb8197aec 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -117,7 +117,7 @@ config SERIAL_8250_DMA
 	  compatible UART controllers that support DMA signaling.
 
 config SERIAL_8250_PCI
-	tristate "8250/16550 PCI device support" if EXPERT
+	tristate "8250/16550 PCI device support"
 	depends on SERIAL_8250 && PCI
 	default SERIAL_8250
 	help
@@ -127,6 +127,11 @@ config SERIAL_8250_PCI
 	  Note that serial ports on NetMos 9835 Multi-I/O cards are handled
 	  by the parport_serial driver, enabled with CONFIG_PARPORT_SERIAL.
 
+config SERIAL_8250_EXAR
+        tristate "8250/16550 PCI device support"
+        depends on SERIAL_8250_PCI
+	default SERIAL_8250
+
 config SERIAL_8250_HP300
 	tristate
 	depends on SERIAL_8250 && HP300
@@ -402,7 +407,7 @@ config SERIAL_8250_INGENIC
 	  its UARTs, say Y to this option. If unsure, say N.
 
 config SERIAL_8250_LPSS
-	tristate "Support for serial ports on Intel LPSS platforms" if EXPERT
+	tristate "Support for serial ports on Intel LPSS platforms"
 	default SERIAL_8250
 	depends on SERIAL_8250 && PCI
 	depends on X86 || COMPILE_TEST
@@ -417,7 +422,7 @@ config SERIAL_8250_LPSS
 	    - Intel Quark X1000 SoC
 
 config SERIAL_8250_MID
-	tristate "Support for serial ports on Intel MID platforms" if EXPERT
+	tristate "Support for serial ports on Intel MID platforms"
 	default SERIAL_8250
 	depends on SERIAL_8250 && PCI
 	depends on X86 || COMPILE_TEST
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 850e721877a9..2f30f9ecdb1b 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SERIAL_8250)		+= 8250.o 8250_base.o
 8250_base-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
+obj-$(CONFIG_SERIAL_8250_EXAR)		+= 8250_exar.o
 obj-$(CONFIG_SERIAL_8250_HP300)		+= 8250_hp300.o
 obj-$(CONFIG_SERIAL_8250_CS)		+= serial_cs.o
 obj-$(CONFIG_SERIAL_8250_ACORN)		+= 8250_acorn.o