diff options
Diffstat (limited to 'drivers/usb/chipidea/usbmisc_imx.c')
| -rw-r--r-- | drivers/usb/chipidea/usbmisc_imx.c | 190 |
1 files changed, 183 insertions, 7 deletions
diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c index def80ff547e4..d8b67e150b12 100644 --- a/drivers/usb/chipidea/usbmisc_imx.c +++ b/drivers/usb/chipidea/usbmisc_imx.c @@ -63,11 +63,24 @@ #define MX6_BM_NON_BURST_SETTING BIT(1) #define MX6_BM_OVER_CUR_DIS BIT(7) #define MX6_BM_OVER_CUR_POLARITY BIT(8) +#define MX6_BM_PWR_POLARITY BIT(9) #define MX6_BM_WAKEUP_ENABLE BIT(10) +#define MX6_BM_UTMI_ON_CLOCK BIT(13) #define MX6_BM_ID_WAKEUP BIT(16) #define MX6_BM_VBUS_WAKEUP BIT(17) #define MX6SX_BM_DPDM_WAKEUP_EN BIT(29) #define MX6_BM_WAKEUP_INTR BIT(31) + +#define MX6_USB_HSIC_CTRL_OFFSET 0x10 +/* Send resume signal without 480Mhz PHY clock */ +#define MX6SX_BM_HSIC_AUTO_RESUME BIT(23) +/* set before portsc.suspendM = 1 */ +#define MX6_BM_HSIC_DEV_CONN BIT(21) +/* HSIC enable */ +#define MX6_BM_HSIC_EN BIT(12) +/* Force HSIC module 480M clock on, even when in Host is in suspend mode */ +#define MX6_BM_HSIC_CLK_ON BIT(11) + #define MX6_USB_OTG1_PHY_CTRL 0x18 /* For imx6dql, it is host-only controller, for later imx6, it is otg's */ #define MX6_USB_OTG2_PHY_CTRL 0x1c @@ -94,6 +107,10 @@ struct usbmisc_ops { int (*post)(struct imx_usbmisc_data *data); /* It's called when we need to enable/disable usb wakeup */ int (*set_wakeup)(struct imx_usbmisc_data *data, bool enabled); + /* It's called before setting portsc.suspendM */ + int (*hsic_set_connect)(struct imx_usbmisc_data *data); + /* It's called during suspend/resume */ + int (*hsic_set_clk)(struct imx_usbmisc_data *data, bool enabled); }; struct imx_usbmisc { @@ -120,6 +137,14 @@ static int usbmisc_imx25_init(struct imx_usbmisc_data *data) val &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PP_BIT); val |= (MX25_EHCI_INTERFACE_DIFF_UNI & MX25_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT; val |= (MX25_OTG_PM_BIT | MX25_OTG_OCPOL_BIT); + + /* + * If the polarity is not configured assume active high for + * historical reasons. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + val &= ~MX25_OTG_OCPOL_BIT; + writel(val, usbmisc->base); break; case 1: @@ -129,6 +154,13 @@ static int usbmisc_imx25_init(struct imx_usbmisc_data *data) val |= (MX25_H1_PM_BIT | MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT); + /* + * If the polarity is not configured assume active high for + * historical reasons. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + val &= ~MX25_H1_OCPOL_BIT; + writel(val, usbmisc->base); break; @@ -340,12 +372,21 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data) reg = readl(usbmisc->base + data->index * 4); if (data->disable_oc) { reg |= MX6_BM_OVER_CUR_DIS; - } else if (data->oc_polarity == 1) { - /* High active */ - reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY); } else { - reg &= ~(MX6_BM_OVER_CUR_DIS); + reg &= ~MX6_BM_OVER_CUR_DIS; + + /* + * If the polarity is not configured keep it as setup by the + * bootloader. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + reg |= MX6_BM_OVER_CUR_POLARITY; + else if (data->oc_pol_configured) + reg &= ~MX6_BM_OVER_CUR_POLARITY; } + /* If the polarity is not set keep it as setup by the bootlader */ + if (data->pwr_pol == 1) + reg |= MX6_BM_PWR_POLARITY; writel(reg, usbmisc->base + data->index * 4); /* SoC non-burst setting */ @@ -353,6 +394,18 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data) writel(reg | MX6_BM_NON_BURST_SETTING, usbmisc->base + data->index * 4); + /* For HSIC controller */ + if (data->hsic) { + reg = readl(usbmisc->base + data->index * 4); + writel(reg | MX6_BM_UTMI_ON_CLOCK, + usbmisc->base + data->index * 4); + reg = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + + (data->index - 2) * 4); + reg |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON; + writel(reg, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + + (data->index - 2) * 4); + } + spin_unlock_irqrestore(&usbmisc->lock, flags); usbmisc_imx6q_set_wakeup(data, false); @@ -360,6 +413,79 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data) return 0; } +static int usbmisc_imx6_hsic_get_reg_offset(struct imx_usbmisc_data *data) +{ + int offset, ret = 0; + + if (data->index == 2 || data->index == 3) { + offset = (data->index - 2) * 4; + } else if (data->index == 0) { + /* + * For SoCs like i.MX7D and later, each USB controller has + * its own non-core register region. For SoCs before i.MX7D, + * the first two USB controllers are non-HSIC controllers. + */ + offset = 0; + } else { + dev_err(data->dev, "index is error for usbmisc\n"); + ret = -EINVAL; + } + + return ret ? ret : offset; +} + +static int usbmisc_imx6_hsic_set_connect(struct imx_usbmisc_data *data) +{ + unsigned long flags; + u32 val; + struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev); + int offset; + + spin_lock_irqsave(&usbmisc->lock, flags); + offset = usbmisc_imx6_hsic_get_reg_offset(data); + if (offset < 0) { + spin_unlock_irqrestore(&usbmisc->lock, flags); + return offset; + } + + val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset); + if (!(val & MX6_BM_HSIC_DEV_CONN)) + writel(val | MX6_BM_HSIC_DEV_CONN, + usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset); + + spin_unlock_irqrestore(&usbmisc->lock, flags); + + return 0; +} + +static int usbmisc_imx6_hsic_set_clk(struct imx_usbmisc_data *data, bool on) +{ + unsigned long flags; + u32 val; + struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev); + int offset; + + spin_lock_irqsave(&usbmisc->lock, flags); + offset = usbmisc_imx6_hsic_get_reg_offset(data); + if (offset < 0) { + spin_unlock_irqrestore(&usbmisc->lock, flags); + return offset; + } + + val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset); + val |= MX6_BM_HSIC_EN | MX6_BM_HSIC_CLK_ON; + if (on) + val |= MX6_BM_HSIC_CLK_ON; + else + val &= ~MX6_BM_HSIC_CLK_ON; + + writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET + offset); + spin_unlock_irqrestore(&usbmisc->lock, flags); + + return 0; +} + + static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data) { void __iomem *reg = NULL; @@ -385,6 +511,13 @@ static int usbmisc_imx6sx_init(struct imx_usbmisc_data *data) spin_unlock_irqrestore(&usbmisc->lock, flags); } + /* For HSIC controller */ + if (data->hsic) { + val = readl(usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET); + val |= MX6SX_BM_HSIC_AUTO_RESUME; + writel(val, usbmisc->base + MX6_USB_HSIC_CTRL_OFFSET); + } + return 0; } @@ -444,16 +577,28 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data) reg = readl(usbmisc->base); if (data->disable_oc) { reg |= MX6_BM_OVER_CUR_DIS; - } else if (data->oc_polarity == 1) { - /* High active */ - reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY); + } else { + reg &= ~MX6_BM_OVER_CUR_DIS; + + /* + * If the polarity is not configured keep it as setup by the + * bootloader. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + reg |= MX6_BM_OVER_CUR_POLARITY; + else if (data->oc_pol_configured) + reg &= ~MX6_BM_OVER_CUR_POLARITY; } + /* If the polarity is not set keep it as setup by the bootlader */ + if (data->pwr_pol == 1) + reg |= MX6_BM_PWR_POLARITY; writel(reg, usbmisc->base); reg = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2); reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK; writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID, usbmisc->base + MX7D_USBNC_USB_CTRL2); + spin_unlock_irqrestore(&usbmisc->lock, flags); usbmisc_imx7d_set_wakeup(data, false); @@ -481,6 +626,8 @@ static const struct usbmisc_ops imx53_usbmisc_ops = { static const struct usbmisc_ops imx6q_usbmisc_ops = { .set_wakeup = usbmisc_imx6q_set_wakeup, .init = usbmisc_imx6q_init, + .hsic_set_connect = usbmisc_imx6_hsic_set_connect, + .hsic_set_clk = usbmisc_imx6_hsic_set_clk, }; static const struct usbmisc_ops vf610_usbmisc_ops = { @@ -490,6 +637,8 @@ static const struct usbmisc_ops vf610_usbmisc_ops = { static const struct usbmisc_ops imx6sx_usbmisc_ops = { .set_wakeup = usbmisc_imx6q_set_wakeup, .init = usbmisc_imx6sx_init, + .hsic_set_connect = usbmisc_imx6_hsic_set_connect, + .hsic_set_clk = usbmisc_imx6_hsic_set_clk, }; static const struct usbmisc_ops imx7d_usbmisc_ops = { @@ -546,6 +695,33 @@ int imx_usbmisc_set_wakeup(struct imx_usbmisc_data *data, bool enabled) } EXPORT_SYMBOL_GPL(imx_usbmisc_set_wakeup); +int imx_usbmisc_hsic_set_connect(struct imx_usbmisc_data *data) +{ + struct imx_usbmisc *usbmisc; + + if (!data) + return 0; + + usbmisc = dev_get_drvdata(data->dev); + if (!usbmisc->ops->hsic_set_connect || !data->hsic) + return 0; + return usbmisc->ops->hsic_set_connect(data); +} +EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_connect); + +int imx_usbmisc_hsic_set_clk(struct imx_usbmisc_data *data, bool on) +{ + struct imx_usbmisc *usbmisc; + + if (!data) + return 0; + + usbmisc = dev_get_drvdata(data->dev); + if (!usbmisc->ops->hsic_set_clk || !data->hsic) + return 0; + return usbmisc->ops->hsic_set_clk(data, on); +} +EXPORT_SYMBOL_GPL(imx_usbmisc_hsic_set_clk); static const struct of_device_id usbmisc_imx_dt_ids[] = { { .compatible = "fsl,imx25-usbmisc", |