diff options
Diffstat (limited to 'drivers/usb/dwc2/core.h')
| -rw-r--r-- | drivers/usb/dwc2/core.h | 227 |
1 files changed, 20 insertions, 207 deletions
diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h index f28274233596..2abe15fc628e 100644 --- a/drivers/usb/dwc2/core.h +++ b/drivers/usb/dwc2/core.h @@ -314,7 +314,8 @@ enum dwc2_ep0_state { * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters * 1 - Allow dynamic FIFO sizing (default, if available) * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs - * are enabled + * are enabled for non-periodic IN endpoints in device + * mode. * @host_rx_fifo_size: Number of 4-byte words in the Rx FIFO in host mode when * dynamic FIFO sizing is enabled * 16 to 32768 @@ -430,11 +431,18 @@ struct dwc2_core_params { * dwc2_set_all_params! */ int otg_cap; +#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0 +#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1 +#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 + int otg_ver; int dma_enable; int dma_desc_enable; int dma_desc_fs_enable; int speed; +#define DWC2_SPEED_PARAM_HIGH 0 +#define DWC2_SPEED_PARAM_FULL 1 + int enable_dynamic_fifo; int en_multiple_tx_fifo; int host_rx_fifo_size; @@ -444,13 +452,23 @@ struct dwc2_core_params { int max_packet_count; int host_channels; int phy_type; +#define DWC2_PHY_TYPE_PARAM_FS 0 +#define DWC2_PHY_TYPE_PARAM_UTMI 1 +#define DWC2_PHY_TYPE_PARAM_ULPI 2 + int phy_utmi_width; int phy_ulpi_ddr; int phy_ulpi_ext_vbus; +#define DWC2_PHY_ULPI_INTERNAL_VBUS 0 +#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1 + int i2c_enable; int ulpi_fs_ls; int host_support_fs_ls_low_power; int host_ls_low_power_phy_clk; +#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 +#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 + int ts_dline; int reload_ctl; int ahbcfg; @@ -1048,216 +1066,11 @@ extern irqreturn_t dwc2_handle_common_intr(int irq, void *dev); /* The device ID match table */ extern const struct of_device_id dwc2_of_match_table[]; -/* OTG Core Parameters */ - -/* - * Specifies the OTG capabilities. The driver will automatically - * detect the value for this parameter if none is specified. - * 0 - HNP and SRP capable (default) - * 1 - SRP Only capable - * 2 - No HNP/SRP capable - */ -extern void dwc2_set_param_otg_cap(struct dwc2_hsotg *hsotg, int val); -#define DWC2_CAP_PARAM_HNP_SRP_CAPABLE 0 -#define DWC2_CAP_PARAM_SRP_ONLY_CAPABLE 1 -#define DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 - -/* - * Specifies whether to use slave or DMA mode for accessing the data - * FIFOs. The driver will automatically detect the value for this - * parameter if none is specified. - * 0 - Slave - * 1 - DMA (default, if available) - */ -extern void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val); - -/* - * When DMA mode is enabled specifies whether to use - * address DMA or DMA Descritor mode for accessing the data - * FIFOs in device mode. The driver will automatically detect - * the value for this parameter if none is specified. - * 0 - address DMA - * 1 - DMA Descriptor(default, if available) - */ -extern void dwc2_set_param_dma_desc_enable(struct dwc2_hsotg *hsotg, int val); - -/* - * When DMA mode is enabled specifies whether to use - * address DMA or DMA Descritor mode with full speed devices - * for accessing the data FIFOs in host mode. - * 0 - address DMA - * 1 - FS DMA Descriptor(default, if available) - */ -extern void dwc2_set_param_dma_desc_fs_enable(struct dwc2_hsotg *hsotg, - int val); - -/* - * Specifies the maximum speed of operation in host and device mode. - * The actual speed depends on the speed of the attached device and - * the value of phy_type. The actual speed depends on the speed of the - * attached device. - * 0 - High Speed (default) - * 1 - Full Speed - */ -extern void dwc2_set_param_speed(struct dwc2_hsotg *hsotg, int val); -#define DWC2_SPEED_PARAM_HIGH 0 -#define DWC2_SPEED_PARAM_FULL 1 - -/* - * Specifies whether low power mode is supported when attached - * to a Full Speed or Low Speed device in host mode. - * - * 0 - Don't support low power mode (default) - * 1 - Support low power mode - */ -extern void dwc2_set_param_host_support_fs_ls_low_power( - struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies the PHY clock rate in low power mode when connected to a - * Low Speed device in host mode. This parameter is applicable only if - * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS - * then defaults to 6 MHZ otherwise 48 MHZ. - * - * 0 - 48 MHz - * 1 - 6 MHz - */ -extern void dwc2_set_param_host_ls_low_power_phy_clk(struct dwc2_hsotg *hsotg, - int val); -#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 -#define DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 - -/* - * 0 - Use cC FIFO size parameters - * 1 - Allow dynamic FIFO sizing (default) - */ -extern void dwc2_set_param_enable_dynamic_fifo(struct dwc2_hsotg *hsotg, - int val); - -/* - * Number of 4-byte words in the Rx FIFO in host mode when dynamic - * FIFO sizing is enabled. - * 16 to 32768 (default 1024) - */ -extern void dwc2_set_param_host_rx_fifo_size(struct dwc2_hsotg *hsotg, int val); - -/* - * Number of 4-byte words in the non-periodic Tx FIFO in host mode - * when Dynamic FIFO sizing is enabled in the core. - * 16 to 32768 (default 256) - */ -extern void dwc2_set_param_host_nperio_tx_fifo_size(struct dwc2_hsotg *hsotg, - int val); - -/* - * Number of 4-byte words in the host periodic Tx FIFO when dynamic - * FIFO sizing is enabled. - * 16 to 32768 (default 256) - */ -extern void dwc2_set_param_host_perio_tx_fifo_size(struct dwc2_hsotg *hsotg, - int val); - -/* - * The maximum transfer size supported in bytes. - * 2047 to 65,535 (default 65,535) - */ -extern void dwc2_set_param_max_transfer_size(struct dwc2_hsotg *hsotg, int val); - -/* - * The maximum number of packets in a transfer. - * 15 to 511 (default 511) - */ -extern void dwc2_set_param_max_packet_count(struct dwc2_hsotg *hsotg, int val); - -/* - * The number of host channel registers to use. - * 1 to 16 (default 11) - * Note: The FPGA configuration supports a maximum of 11 host channels. - */ -extern void dwc2_set_param_host_channels(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies the type of PHY interface to use. By default, the driver - * will automatically detect the phy_type. - * - * 0 - Full Speed PHY - * 1 - UTMI+ (default) - * 2 - ULPI - */ -extern void dwc2_set_param_phy_type(struct dwc2_hsotg *hsotg, int val); -#define DWC2_PHY_TYPE_PARAM_FS 0 -#define DWC2_PHY_TYPE_PARAM_UTMI 1 -#define DWC2_PHY_TYPE_PARAM_ULPI 2 - -/* - * Specifies the UTMI+ Data Width. This parameter is - * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI - * PHY_TYPE, this parameter indicates the data width between - * the MAC and the ULPI Wrapper.) Also, this parameter is - * applicable only if the OTG_HSPHY_WIDTH cC parameter was set - * to "8 and 16 bits", meaning that the core has been - * configured to work at either data path width. - * - * 8 or 16 bits (default 16) - */ -extern void dwc2_set_param_phy_utmi_width(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether the ULPI operates at double or single - * data rate. This parameter is only applicable if PHY_TYPE is - * ULPI. - * - * 0 - single data rate ULPI interface with 8 bit wide data - * bus (default) - * 1 - double data rate ULPI interface with 4 bit wide data - * bus - */ -extern void dwc2_set_param_phy_ulpi_ddr(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether to use the internal or external supply to - * drive the vbus with a ULPI phy. - */ -extern void dwc2_set_param_phy_ulpi_ext_vbus(struct dwc2_hsotg *hsotg, int val); -#define DWC2_PHY_ULPI_INTERNAL_VBUS 0 -#define DWC2_PHY_ULPI_EXTERNAL_VBUS 1 - -/* - * Specifies whether to use the I2Cinterface for full speed PHY. This - * parameter is only applicable if PHY_TYPE is FS. - * 0 - No (default) - * 1 - Yes - */ -extern void dwc2_set_param_i2c_enable(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ulpi_fs_ls(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ts_dline(struct dwc2_hsotg *hsotg, int val); - -/* - * Specifies whether dedicated transmit FIFOs are - * enabled for non periodic IN endpoints in device mode - * 0 - No - * 1 - Yes - */ -extern void dwc2_set_param_en_multiple_tx_fifo(struct dwc2_hsotg *hsotg, - int val); - -extern void dwc2_set_param_reload_ctl(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_ahbcfg(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_param_otg_ver(struct dwc2_hsotg *hsotg, int val); - -extern void dwc2_set_parameters(struct dwc2_hsotg *hsotg, - const struct dwc2_core_params *params); - -extern int dwc2_get_hwparams(struct dwc2_hsotg *hsotg); - extern int dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg); extern int dwc2_lowlevel_hw_disable(struct dwc2_hsotg *hsotg); /* Parameters */ +int dwc2_get_hwparams(struct dwc2_hsotg *hsotg); int dwc2_init_params(struct dwc2_hsotg *hsotg); /* |