1 files changed, 65 insertions, 1 deletions

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 82bc075ba97c..359824c871cd 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -1580,7 +1580,7 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 {
 	struct dwc3		*dwc = dep->dwc;
 
-	if (!dep->endpoint.desc) {
+	if (!dep->endpoint.desc || !dwc->pullups_connected) {
 		dev_err(dwc->dev, "%s: can't queue to disabled endpoint\n",
 				dep->name);
 		return -ESHUTDOWN;
@@ -1999,6 +1999,21 @@ static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,
 	return 0;
 }
 
+static void dwc3_stop_active_transfers(struct dwc3 *dwc)
+{
+	u32 epnum;
+
+	for (epnum = 2; epnum < dwc->num_eps; epnum++) {
+		struct dwc3_ep *dep;
+
+		dep = dwc->eps[epnum];
+		if (!dep)
+			continue;
+
+		dwc3_remove_requests(dwc, dep);
+	}
+}
+
 static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
 {
 	u32			reg;
@@ -2044,6 +2059,9 @@ static int dwc3_gadget_run_stop(struct dwc3 *dwc, int is_on, int suspend)
 	return 0;
 }
 
+static void dwc3_gadget_disable_irq(struct dwc3 *dwc);
+static void __dwc3_gadget_stop(struct dwc3 *dwc);
+
 static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 {
 	struct dwc3		*dwc = gadget_to_dwc(g);
@@ -2067,7 +2085,46 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 		}
 	}
 
+	/*
+	 * Synchronize any pending event handling before executing the controller
+	 * halt routine.
+	 */
+	if (!is_on) {
+		dwc3_gadget_disable_irq(dwc);
+		synchronize_irq(dwc->irq_gadget);
+	}
+
 	spin_lock_irqsave(&dwc->lock, flags);
+
+	if (!is_on) {
+		u32 count;
+
+		/*
+		 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
+		 * Section 4.1.8 Table 4-7, it states that for a device-initiated
+		 * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
+		 * command for any active transfers" before clearing the RunStop
+		 * bit.
+		 */
+		dwc3_stop_active_transfers(dwc);
+		__dwc3_gadget_stop(dwc);
+
+		/*
+		 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
+		 * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
+		 * "software needs to acknowledge the events that are generated
+		 * (by writing to GEVNTCOUNTn) while it is waiting for this bit
+		 * to be set to '1'."
+		 */
+		count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+		count &= DWC3_GEVNTCOUNT_MASK;
+		if (count > 0) {
+			dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
+			dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
+						dwc->ev_buf->length;
+		}
+	}
+
 	ret = dwc3_gadget_run_stop(dwc, is_on, false);
 	spin_unlock_irqrestore(&dwc->lock, flags);
 
@@ -3200,6 +3257,13 @@ static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
 	}
 
 	dwc3_reset_gadget(dwc);
+	/*
+	 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
+	 * Section 4.1.2 Table 4-2, it states that during a USB reset, the SW
+	 * needs to ensure that it sends "a DEPENDXFER command for any active
+	 * transfers."
+	 */
+	dwc3_stop_active_transfers(dwc);
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg &= ~DWC3_DCTL_TSTCTRL_MASK;