diff options
Diffstat (limited to 'drivers/usb/host/xhci.c')
| -rw-r--r-- | drivers/usb/host/xhci.c | 491 |
1 files changed, 483 insertions, 8 deletions
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 36641a7f2371..a979cd0dbe0f 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -152,7 +152,7 @@ int xhci_reset(struct xhci_hcd *xhci) { u32 command; u32 state; - int ret; + int ret, i; state = xhci_readl(xhci, &xhci->op_regs->status); if ((state & STS_HALT) == 0) { @@ -175,7 +175,15 @@ int xhci_reset(struct xhci_hcd *xhci) * xHCI cannot write to any doorbells or operational registers other * than status until the "Controller Not Ready" flag is cleared. */ - return handshake(xhci, &xhci->op_regs->status, STS_CNR, 0, 250 * 1000); + ret = handshake(xhci, &xhci->op_regs->status, STS_CNR, 0, 250 * 1000); + + for (i = 0; i < 2; ++i) { + xhci->bus_state[i].port_c_suspend = 0; + xhci->bus_state[i].suspended_ports = 0; + xhci->bus_state[i].resuming_ports = 0; + } + + return ret; } #ifdef CONFIG_PCI @@ -787,8 +795,8 @@ int xhci_suspend(struct xhci_hcd *xhci) command = xhci_readl(xhci, &xhci->op_regs->command); command |= CMD_CSS; xhci_writel(xhci, command, &xhci->op_regs->command); - if (handshake(xhci, &xhci->op_regs->status, STS_SAVE, 0, 10*100)) { - xhci_warn(xhci, "WARN: xHC CMD_CSS timeout\n"); + if (handshake(xhci, &xhci->op_regs->status, STS_SAVE, 0, 10 * 1000)) { + xhci_warn(xhci, "WARN: xHC save state timeout\n"); spin_unlock_irq(&xhci->lock); return -ETIMEDOUT; } @@ -840,8 +848,8 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) command |= CMD_CRS; xhci_writel(xhci, command, &xhci->op_regs->command); if (handshake(xhci, &xhci->op_regs->status, - STS_RESTORE, 0, 10*100)) { - xhci_dbg(xhci, "WARN: xHC CMD_CSS timeout\n"); + STS_RESTORE, 0, 10 * 1000)) { + xhci_warn(xhci, "WARN: xHC restore state timeout\n"); spin_unlock_irq(&xhci->lock); return -ETIMEDOUT; } @@ -2438,7 +2446,7 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, udev->slot_id, must_succeed); else ret = xhci_queue_evaluate_context(xhci, in_ctx->dma, - udev->slot_id); + udev->slot_id, must_succeed); if (ret < 0) { if (command) list_del(&command->cmd_list); @@ -3863,6 +3871,474 @@ int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev) #endif /* CONFIG_USB_SUSPEND */ +/*---------------------- USB 3.0 Link PM functions ------------------------*/ + +#ifdef CONFIG_PM +/* Service interval in nanoseconds = 2^(bInterval - 1) * 125us * 1000ns / 1us */ +static unsigned long long xhci_service_interval_to_ns( + struct usb_endpoint_descriptor *desc) +{ + return (1 << (desc->bInterval - 1)) * 125 * 1000; +} + +static u16 xhci_get_timeout_no_hub_lpm(struct usb_device *udev, + enum usb3_link_state state) +{ + unsigned long long sel; + unsigned long long pel; + unsigned int max_sel_pel; + char *state_name; + + switch (state) { + case USB3_LPM_U1: + /* Convert SEL and PEL stored in nanoseconds to microseconds */ + sel = DIV_ROUND_UP(udev->u1_params.sel, 1000); + pel = DIV_ROUND_UP(udev->u1_params.pel, 1000); + max_sel_pel = USB3_LPM_MAX_U1_SEL_PEL; + state_name = "U1"; + break; + case USB3_LPM_U2: + sel = DIV_ROUND_UP(udev->u2_params.sel, 1000); + pel = DIV_ROUND_UP(udev->u2_params.pel, 1000); + max_sel_pel = USB3_LPM_MAX_U2_SEL_PEL; + state_name = "U2"; + break; + default: + dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n", + __func__); + return USB3_LPM_DISABLED; + } + + if (sel <= max_sel_pel && pel <= max_sel_pel) + return USB3_LPM_DEVICE_INITIATED; + + if (sel > max_sel_pel) + dev_dbg(&udev->dev, "Device-initiated %s disabled " + "due to long SEL %llu ms\n", + state_name, sel); + else + dev_dbg(&udev->dev, "Device-initiated %s disabled " + "due to long PEL %llu\n ms", + state_name, pel); + return USB3_LPM_DISABLED; +} + +/* Returns the hub-encoded U1 timeout value. + * The U1 timeout should be the maximum of the following values: + * - For control endpoints, U1 system exit latency (SEL) * 3 + * - For bulk endpoints, U1 SEL * 5 + * - For interrupt endpoints: + * - Notification EPs, U1 SEL * 3 + * - Periodic EPs, max(105% of bInterval, U1 SEL * 2) + * - For isochronous endpoints, max(105% of bInterval, U1 SEL * 2) + */ +static u16 xhci_calculate_intel_u1_timeout(struct usb_device *udev, + struct usb_endpoint_descriptor *desc) +{ + unsigned long long timeout_ns; + int ep_type; + int intr_type; + + ep_type = usb_endpoint_type(desc); + switch (ep_type) { + case USB_ENDPOINT_XFER_CONTROL: + timeout_ns = udev->u1_params.sel * 3; + break; + case USB_ENDPOINT_XFER_BULK: + timeout_ns = udev->u1_params.sel * 5; + break; + case USB_ENDPOINT_XFER_INT: + intr_type = usb_endpoint_interrupt_type(desc); + if (intr_type == USB_ENDPOINT_INTR_NOTIFICATION) { + timeout_ns = udev->u1_params.sel * 3; + break; + } + /* Otherwise the calculation is the same as isoc eps */ + case USB_ENDPOINT_XFER_ISOC: + timeout_ns = xhci_service_interval_to_ns(desc); + timeout_ns = DIV_ROUND_UP_ULL(timeout_ns * 105, 100); + if (timeout_ns < udev->u1_params.sel * 2) + timeout_ns = udev->u1_params.sel * 2; + break; + default: + return 0; + } + + /* The U1 timeout is encoded in 1us intervals. */ + timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 1000); + /* Don't return a timeout of zero, because that's USB3_LPM_DISABLED. */ + if (timeout_ns == USB3_LPM_DISABLED) + timeout_ns++; + + /* If the necessary timeout value is bigger than what we can set in the + * USB 3.0 hub, we have to disable hub-initiated U1. + */ + if (timeout_ns <= USB3_LPM_U1_MAX_TIMEOUT) + return timeout_ns; + dev_dbg(&udev->dev, "Hub-initiated U1 disabled " + "due to long timeout %llu ms\n", timeout_ns); + return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U1); +} + +/* Returns the hub-encoded U2 timeout value. + * The U2 timeout should be the maximum of: + * - 10 ms (to avoid the bandwidth impact on the scheduler) + * - largest bInterval of any active periodic endpoint (to avoid going + * into lower power link states between intervals). + * - the U2 Exit Latency of the device + */ +static u16 xhci_calculate_intel_u2_timeout(struct usb_device *udev, + struct usb_endpoint_descriptor *desc) +{ + unsigned long long timeout_ns; + unsigned long long u2_del_ns; + + timeout_ns = 10 * 1000 * 1000; + + if ((usb_endpoint_xfer_int(desc) || usb_endpoint_xfer_isoc(desc)) && + (xhci_service_interval_to_ns(desc) > timeout_ns)) + timeout_ns = xhci_service_interval_to_ns(desc); + + u2_del_ns = udev->bos->ss_cap->bU2DevExitLat * 1000; + if (u2_del_ns > timeout_ns) + timeout_ns = u2_del_ns; + + /* The U2 timeout is encoded in 256us intervals */ + timeout_ns = DIV_ROUND_UP_ULL(timeout_ns, 256 * 1000); + /* If the necessary timeout value is bigger than what we can set in the + * USB 3.0 hub, we have to disable hub-initiated U2. + */ + if (timeout_ns <= USB3_LPM_U2_MAX_TIMEOUT) + return timeout_ns; + dev_dbg(&udev->dev, "Hub-initiated U2 disabled " + "due to long timeout %llu ms\n", timeout_ns); + return xhci_get_timeout_no_hub_lpm(udev, USB3_LPM_U2); +} + +static u16 xhci_call_host_update_timeout_for_endpoint(struct xhci_hcd *xhci, + struct usb_device *udev, + struct usb_endpoint_descriptor *desc, + enum usb3_link_state state, + u16 *timeout) +{ + if (state == USB3_LPM_U1) { + if (xhci->quirks & XHCI_INTEL_HOST) + return xhci_calculate_intel_u1_timeout(udev, desc); + } else { + if (xhci->quirks & XHCI_INTEL_HOST) + return xhci_calculate_intel_u2_timeout(udev, desc); + } + + return USB3_LPM_DISABLED; +} + +static int xhci_update_timeout_for_endpoint(struct xhci_hcd *xhci, + struct usb_device *udev, + struct usb_endpoint_descriptor *desc, + enum usb3_link_state state, + u16 *timeout) +{ + u16 alt_timeout; + + alt_timeout = xhci_call_host_update_timeout_for_endpoint(xhci, udev, + desc, state, timeout); + + /* If we found we can't enable hub-initiated LPM, or + * the U1 or U2 exit latency was too high to allow + * device-initiated LPM as well, just stop searching. + */ + if (alt_timeout == USB3_LPM_DISABLED || + alt_timeout == USB3_LPM_DEVICE_INITIATED) { + *timeout = alt_timeout; + return -E2BIG; + } + if (alt_timeout > *timeout) + *timeout = alt_timeout; + return 0; +} + +static int xhci_update_timeout_for_interface(struct xhci_hcd *xhci, + struct usb_device *udev, + struct usb_host_interface *alt, + enum usb3_link_state state, + u16 *timeout) +{ + int j; + + for (j = 0; j < alt->desc.bNumEndpoints; j++) { + if (xhci_update_timeout_for_endpoint(xhci, udev, + &alt->endpoint[j].desc, state, timeout)) + return -E2BIG; + continue; + } + return 0; +} + +static int xhci_check_intel_tier_policy(struct usb_device *udev, + enum usb3_link_state state) +{ + struct usb_device *parent; + unsigned int num_hubs; + + if (state == USB3_LPM_U2) + return 0; + + /* Don't enable U1 if the device is on a 2nd tier hub or lower. */ + for (parent = udev->parent, num_hubs = 0; parent->parent; + parent = parent->parent) + num_hubs++; + + if (num_hubs < 2) + return 0; + + dev_dbg(&udev->dev, "Disabling U1 link state for device" + " below second-tier hub.\n"); + dev_dbg(&udev->dev, "Plug device into first-tier hub " + "to decrease power consumption.\n"); + return -E2BIG; +} + +static int xhci_check_tier_policy(struct xhci_hcd *xhci, + struct usb_device *udev, + enum usb3_link_state state) +{ + if (xhci->quirks & XHCI_INTEL_HOST) + return xhci_check_intel_tier_policy(udev, state); + return -EINVAL; +} + +/* Returns the U1 or U2 timeout that should be enabled. + * If the tier check or timeout setting functions return with a non-zero exit + * code, that means the timeout value has been finalized and we shouldn't look + * at any more endpoints. + */ +static u16 xhci_calculate_lpm_timeout(struct usb_hcd *hcd, + struct usb_device *udev, enum usb3_link_state state) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + struct usb_host_config *config; + char *state_name; + int i; + u16 timeout = USB3_LPM_DISABLED; + + if (state == USB3_LPM_U1) + state_name = "U1"; + else if (state == USB3_LPM_U2) + state_name = "U2"; + else { + dev_warn(&udev->dev, "Can't enable unknown link state %i\n", + state); + return timeout; + } + + if (xhci_check_tier_policy(xhci, udev, state) < 0) + return timeout; + + /* Gather some information about the currently installed configuration + * and alternate interface settings. + */ + if (xhci_update_timeout_for_endpoint(xhci, udev, &udev->ep0.desc, + state, &timeout)) + return timeout; + + config = udev->actconfig; + if (!config) + return timeout; + + for (i = 0; i < USB_MAXINTERFACES; i++) { + struct usb_driver *driver; + struct usb_interface *intf = config->interface[i]; + + if (!intf) + continue; + + /* Check if any currently bound drivers want hub-initiated LPM + * disabled. + */ + if (intf->dev.driver) { + driver = to_usb_driver(intf->dev.driver); + if (driver && driver->disable_hub_initiated_lpm) { + dev_dbg(&udev->dev, "Hub-initiated %s disabled " + "at request of driver %s\n", + state_name, driver->name); + return xhci_get_timeout_no_hub_lpm(udev, state); + } + } + + /* Not sure how this could happen... */ + if (!intf->cur_altsetting) + continue; + + if (xhci_update_timeout_for_interface(xhci, udev, + intf->cur_altsetting, + state, &timeout)) + return timeout; + } + return timeout; +} + +/* + * Issue an Evaluate Context command to change the Maximum Exit Latency in the + * slot context. If that succeeds, store the new MEL in the xhci_virt_device. + */ +static int xhci_change_max_exit_latency(struct xhci_hcd *xhci, + struct usb_device *udev, u16 max_exit_latency) +{ + struct xhci_virt_device *virt_dev; + struct xhci_command *command; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_slot_ctx *slot_ctx; + unsigned long flags; + int ret; + + spin_lock_irqsave(&xhci->lock, flags); + if (max_exit_latency == xhci->devs[udev->slot_id]->current_mel) { + spin_unlock_irqrestore(&xhci->lock, flags); + return 0; + } + + /* Attempt to issue an Evaluate Context command to change the MEL. */ + virt_dev = xhci->devs[udev->slot_id]; + command = xhci->lpm_command; + xhci_slot_copy(xhci, command->in_ctx, virt_dev->out_ctx); + spin_unlock_irqrestore(&xhci->lock, flags); + + ctrl_ctx = xhci_get_input_control_ctx(xhci, command->in_ctx); + ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG); + slot_ctx = xhci_get_slot_ctx(xhci, command->in_ctx); + slot_ctx->dev_info2 &= cpu_to_le32(~((u32) MAX_EXIT)); + slot_ctx->dev_info2 |= cpu_to_le32(max_exit_latency); + + xhci_dbg(xhci, "Set up evaluate context for LPM MEL change.\n"); + xhci_dbg(xhci, "Slot %u Input Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, command->in_ctx, 0); + + /* Issue and wait for the evaluate context command. */ + ret = xhci_configure_endpoint(xhci, udev, command, + true, true); + xhci_dbg(xhci, "Slot %u Output Context:\n", udev->slot_id); + xhci_dbg_ctx(xhci, virt_dev->out_ctx, 0); + + if (!ret) { + spin_lock_irqsave(&xhci->lock, flags); + virt_dev->current_mel = max_exit_latency; + spin_unlock_irqrestore(&xhci->lock, flags); + } + return ret; +} + +static int calculate_max_exit_latency(struct usb_device *udev, + enum usb3_link_state state_changed, + u16 hub_encoded_timeout) +{ + unsigned long long u1_mel_us = 0; + unsigned long long u2_mel_us = 0; + unsigned long long mel_us = 0; + bool disabling_u1; + bool disabling_u2; + bool enabling_u1; + bool enabling_u2; + + disabling_u1 = (state_changed == USB3_LPM_U1 && + hub_encoded_timeout == USB3_LPM_DISABLED); + disabling_u2 = (state_changed == USB3_LPM_U2 && + hub_encoded_timeout == USB3_LPM_DISABLED); + + enabling_u1 = (state_changed == USB3_LPM_U1 && + hub_encoded_timeout != USB3_LPM_DISABLED); + enabling_u2 = (state_changed == USB3_LPM_U2 && + hub_encoded_timeout != USB3_LPM_DISABLED); + + /* If U1 was already enabled and we're not disabling it, + * or we're going to enable U1, account for the U1 max exit latency. + */ + if ((udev->u1_params.timeout != USB3_LPM_DISABLED && !disabling_u1) || + enabling_u1) + u1_mel_us = DIV_ROUND_UP(udev->u1_params.mel, 1000); + if ((udev->u2_params.timeout != USB3_LPM_DISABLED && !disabling_u2) || + enabling_u2) + u2_mel_us = DIV_ROUND_UP(udev->u2_params.mel, 1000); + + if (u1_mel_us > u2_mel_us) + mel_us = u1_mel_us; + else + mel_us = u2_mel_us; + /* xHCI host controller max exit latency field is only 16 bits wide. */ + if (mel_us > MAX_EXIT) { + dev_warn(&udev->dev, "Link PM max exit latency of %lluus " + "is too big.\n", mel_us); + return -E2BIG; + } + return mel_us; +} + +/* Returns the USB3 hub-encoded value for the U1/U2 timeout. */ +int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd, + struct usb_device *udev, enum usb3_link_state state) +{ + struct xhci_hcd *xhci; + u16 hub_encoded_timeout; + int mel; + int ret; + + xhci = hcd_to_xhci(hcd); + /* The LPM timeout values are pretty host-controller specific, so don't + * enable hub-initiated timeouts unless the vendor has provided + * information about their timeout algorithm. + */ + if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) || + !xhci->devs[udev->slot_id]) + return USB3_LPM_DISABLED; + + hub_encoded_timeout = xhci_calculate_lpm_timeout(hcd, udev, state); + mel = calculate_max_exit_latency(udev, state, hub_encoded_timeout); + if (mel < 0) { + /* Max Exit Latency is too big, disable LPM. */ + hub_encoded_timeout = USB3_LPM_DISABLED; + mel = 0; + } + + ret = xhci_change_max_exit_latency(xhci, udev, mel); + if (ret) + return ret; + return hub_encoded_timeout; +} + +int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd, + struct usb_device *udev, enum usb3_link_state state) +{ + struct xhci_hcd *xhci; + u16 mel; + int ret; + + xhci = hcd_to_xhci(hcd); + if (!xhci || !(xhci->quirks & XHCI_LPM_SUPPORT) || + !xhci->devs[udev->slot_id]) + return 0; + + mel = calculate_max_exit_latency(udev, state, USB3_LPM_DISABLED); + ret = xhci_change_max_exit_latency(xhci, udev, mel); + if (ret) + return ret; + return 0; +} +#else /* CONFIG_PM */ + +int xhci_enable_usb3_lpm_timeout(struct usb_hcd *hcd, + struct usb_device *udev, enum usb3_link_state state) +{ + return USB3_LPM_DISABLED; +} + +int xhci_disable_usb3_lpm_timeout(struct usb_hcd *hcd, + struct usb_device *udev, enum usb3_link_state state) +{ + return 0; +} +#endif /* CONFIG_PM */ + +/*-------------------------------------------------------------------------*/ + /* Once a hub descriptor is fetched for a device, we need to update the xHC's * internal data structures for the device. */ @@ -4090,7 +4566,6 @@ static int __init xhci_hcd_init(void) BUILD_BUG_ON(sizeof(struct xhci_intr_reg) != 8*32/8); /* xhci_run_regs has eight fields and embeds 128 xhci_intr_regs */ BUILD_BUG_ON(sizeof(struct xhci_run_regs) != (8+8*128)*32/8); - BUILD_BUG_ON(sizeof(struct xhci_doorbell_array) != 256*32/8); return 0; unreg_pci: xhci_unregister_pci(); |