diff options
Diffstat (limited to 'drivers/usb/phy')
| -rw-r--r-- | drivers/usb/phy/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-ab8500-usb.c | 26 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-am335x.c | 2 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-generic.c | 39 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-generic.h | 3 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-gpio-vbus-usb.c | 96 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-keystone.c | 2 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-tegra-usb.c | 896 | ||||
| -rw-r--r-- | drivers/usb/phy/phy-ulpi.c | 48 | ||||
| -rw-r--r-- | drivers/usb/phy/phy.c | 13 |
10 files changed, 607 insertions, 522 deletions
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index 24b4f091acb8..ff24fca0a2d9 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -162,7 +162,7 @@ config USB_MXS_PHY config USB_TEGRA_PHY tristate "NVIDIA Tegra USB PHY Driver" - depends on ARCH_TEGRA + depends on ARCH_TEGRA || COMPILE_TEST select USB_COMMON select USB_PHY select USB_ULPI @@ -172,7 +172,7 @@ config USB_TEGRA_PHY config USB_ULPI bool "Generic ULPI Transceiver Driver" - depends on ARM || ARM64 + depends on ARM || ARM64 || COMPILE_TEST select USB_ULPI_VIEWPORT help Enable this to support ULPI connected USB OTG transceivers which diff --git a/drivers/usb/phy/phy-ab8500-usb.c b/drivers/usb/phy/phy-ab8500-usb.c index 4bb4b1d42f32..20c0f082bf9c 100644 --- a/drivers/usb/phy/phy-ab8500-usb.c +++ b/drivers/usb/phy/phy-ab8500-usb.c @@ -108,7 +108,8 @@ enum ab8500_usb_mode { USB_IDLE = 0, USB_PERIPHERAL, USB_HOST, - USB_DEDICATED_CHG + USB_DEDICATED_CHG, + USB_UART }; /* Register USB_LINK_STATUS interrupt */ @@ -393,6 +394,24 @@ static int ab8505_usb_link_status_update(struct ab8500_usb *ab, usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER); break; + /* + * FIXME: For now we rely on the boot firmware to set up the necessary + * PHY/pin configuration for UART mode. + * + * AB8505 does not seem to report any status change for UART cables, + * possibly because it cannot detect them autonomously. + * We may need to measure the ID resistance manually to reliably + * detect UART cables after bootup. + */ + case USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505: + case USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505: + if (ab->mode == USB_IDLE) { + ab->mode = USB_UART; + ab8500_usb_peri_phy_en(ab); + } + + break; + default: break; } @@ -566,6 +585,11 @@ static irqreturn_t ab8500_usb_disconnect_irq(int irq, void *data) ab->vbus_draw = 0; } + if (ab->mode == USB_UART) { + ab8500_usb_peri_phy_dis(ab); + ab->mode = USB_IDLE; + } + if (is_ab8500_2p0(ab->ab8500)) { if (ab->mode == USB_DEDICATED_CHG) { ab8500_usb_wd_linkstatus(ab, diff --git a/drivers/usb/phy/phy-am335x.c b/drivers/usb/phy/phy-am335x.c index f5f0568d8533..8524475d942d 100644 --- a/drivers/usb/phy/phy-am335x.c +++ b/drivers/usb/phy/phy-am335x.c @@ -57,7 +57,7 @@ static int am335x_phy_probe(struct platform_device *pdev) am_phy->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1); - ret = usb_phy_gen_create_phy(dev, &am_phy->usb_phy_gen, NULL); + ret = usb_phy_gen_create_phy(dev, &am_phy->usb_phy_gen); if (ret) return ret; diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c index a53b89be5324..661a229c105d 100644 --- a/drivers/usb/phy/phy-generic.c +++ b/drivers/usb/phy/phy-generic.c @@ -21,8 +21,7 @@ #include <linux/clk.h> #include <linux/regulator/consumer.h> #include <linux/of.h> -#include <linux/of_gpio.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/delay.h> #include "phy-generic.h" @@ -204,8 +203,7 @@ static int nop_set_host(struct usb_otg *otg, struct usb_bus *host) return 0; } -int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop, - struct usb_phy_generic_platform_data *pdata) +int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop) { enum usb_phy_type type = USB_PHY_TYPE_USB2; int err = 0; @@ -221,28 +219,15 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop, needs_vcc = of_property_read_bool(node, "vcc-supply"); needs_clk = of_property_read_bool(node, "clocks"); - nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset", - GPIOD_ASIS); - err = PTR_ERR_OR_ZERO(nop->gpiod_reset); - if (!err) { - nop->gpiod_vbus = devm_gpiod_get_optional(dev, - "vbus-detect", - GPIOD_ASIS); - err = PTR_ERR_OR_ZERO(nop->gpiod_vbus); - } - } else if (pdata) { - type = pdata->type; - clk_rate = pdata->clk_rate; - needs_vcc = pdata->needs_vcc; - if (gpio_is_valid(pdata->gpio_reset)) { - err = devm_gpio_request_one(dev, pdata->gpio_reset, - GPIOF_ACTIVE_LOW, - dev_name(dev)); - if (!err) - nop->gpiod_reset = - gpio_to_desc(pdata->gpio_reset); - } - nop->gpiod_vbus = pdata->gpiod_vbus; + } + nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset", + GPIOD_ASIS); + err = PTR_ERR_OR_ZERO(nop->gpiod_reset); + if (!err) { + nop->gpiod_vbus = devm_gpiod_get_optional(dev, + "vbus-detect", + GPIOD_ASIS); + err = PTR_ERR_OR_ZERO(nop->gpiod_vbus); } if (err == -EPROBE_DEFER) @@ -308,7 +293,7 @@ static int usb_phy_generic_probe(struct platform_device *pdev) if (!nop) return -ENOMEM; - err = usb_phy_gen_create_phy(dev, nop, dev_get_platdata(&pdev->dev)); + err = usb_phy_gen_create_phy(dev, nop); if (err) return err; if (nop->gpiod_vbus) { diff --git a/drivers/usb/phy/phy-generic.h b/drivers/usb/phy/phy-generic.h index 97289627561d..7ee80211a688 100644 --- a/drivers/usb/phy/phy-generic.h +++ b/drivers/usb/phy/phy-generic.h @@ -22,7 +22,6 @@ struct usb_phy_generic { int usb_gen_phy_init(struct usb_phy *phy); void usb_gen_phy_shutdown(struct usb_phy *phy); -int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop, - struct usb_phy_generic_platform_data *pdata); +int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop); #endif diff --git a/drivers/usb/phy/phy-gpio-vbus-usb.c b/drivers/usb/phy/phy-gpio-vbus-usb.c index 553e2573c74f..f13f5530746c 100644 --- a/drivers/usb/phy/phy-gpio-vbus-usb.c +++ b/drivers/usb/phy/phy-gpio-vbus-usb.c @@ -7,7 +7,7 @@ #include <linux/kernel.h> #include <linux/platform_device.h> -#include <linux/gpio.h> +#include <linux/gpio/consumer.h> #include <linux/module.h> #include <linux/slab.h> #include <linux/interrupt.h> @@ -17,7 +17,6 @@ #include <linux/regulator/consumer.h> #include <linux/usb/gadget.h> -#include <linux/usb/gpio_vbus.h> #include <linux/usb/otg.h> @@ -29,6 +28,8 @@ * Needs to be loaded before the UDC driver that will use it. */ struct gpio_vbus_data { + struct gpio_desc *vbus_gpiod; + struct gpio_desc *pullup_gpiod; struct usb_phy phy; struct device *dev; struct regulator *vbus_draw; @@ -83,38 +84,30 @@ static void set_vbus_draw(struct gpio_vbus_data *gpio_vbus, unsigned mA) gpio_vbus->mA = mA; } -static int is_vbus_powered(struct gpio_vbus_mach_info *pdata) +static int is_vbus_powered(struct gpio_vbus_data *gpio_vbus) { - int vbus; - - vbus = gpio_get_value(pdata->gpio_vbus); - if (pdata->gpio_vbus_inverted) - vbus = !vbus; - - return vbus; + return gpiod_get_value(gpio_vbus->vbus_gpiod); } static void gpio_vbus_work(struct work_struct *work) { struct gpio_vbus_data *gpio_vbus = container_of(work, struct gpio_vbus_data, work.work); - struct gpio_vbus_mach_info *pdata = dev_get_platdata(gpio_vbus->dev); - int gpio, status, vbus; + int status, vbus; if (!gpio_vbus->phy.otg->gadget) return; - vbus = is_vbus_powered(pdata); + vbus = is_vbus_powered(gpio_vbus); if ((vbus ^ gpio_vbus->vbus) == 0) return; gpio_vbus->vbus = vbus; /* Peripheral controllers which manage the pullup themselves won't have - * gpio_pullup configured here. If it's configured here, we'll do what - * isp1301_omap::b_peripheral() does and enable the pullup here... although - * that may complicate usb_gadget_{,dis}connect() support. + * a pullup GPIO configured here. If it's configured here, we'll do + * what isp1301_omap::b_peripheral() does and enable the pullup here... + * although that may complicate usb_gadget_{,dis}connect() support. */ - gpio = pdata->gpio_pullup; if (vbus) { status = USB_EVENT_VBUS; @@ -126,16 +119,16 @@ static void gpio_vbus_work(struct work_struct *work) set_vbus_draw(gpio_vbus, 100); /* optionally enable D+ pullup */ - if (gpio_is_valid(gpio)) - gpio_set_value(gpio, !pdata->gpio_pullup_inverted); + if (gpio_vbus->pullup_gpiod) + gpiod_set_value(gpio_vbus->pullup_gpiod, 1); atomic_notifier_call_chain(&gpio_vbus->phy.notifier, status, gpio_vbus->phy.otg->gadget); usb_phy_set_event(&gpio_vbus->phy, USB_EVENT_ENUMERATED); } else { /* optionally disable D+ pullup */ - if (gpio_is_valid(gpio)) - gpio_set_value(gpio, pdata->gpio_pullup_inverted); + if (gpio_vbus->pullup_gpiod) + gpiod_set_value(gpio_vbus->pullup_gpiod, 0); set_vbus_draw(gpio_vbus, 0); @@ -154,12 +147,11 @@ static void gpio_vbus_work(struct work_struct *work) static irqreturn_t gpio_vbus_irq(int irq, void *data) { struct platform_device *pdev = data; - struct gpio_vbus_mach_info *pdata = dev_get_platdata(&pdev->dev); struct gpio_vbus_data *gpio_vbus = platform_get_drvdata(pdev); struct usb_otg *otg = gpio_vbus->phy.otg; dev_dbg(&pdev->dev, "VBUS %s (gadget: %s)\n", - is_vbus_powered(pdata) ? "supplied" : "inactive", + is_vbus_powered(gpio_vbus) ? "supplied" : "inactive", otg->gadget ? otg->gadget->name : "none"); if (otg->gadget) @@ -175,22 +167,18 @@ static int gpio_vbus_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget) { struct gpio_vbus_data *gpio_vbus; - struct gpio_vbus_mach_info *pdata; struct platform_device *pdev; - int gpio; gpio_vbus = container_of(otg->usb_phy, struct gpio_vbus_data, phy); pdev = to_platform_device(gpio_vbus->dev); - pdata = dev_get_platdata(gpio_vbus->dev); - gpio = pdata->gpio_pullup; if (!gadget) { dev_dbg(&pdev->dev, "unregistering gadget '%s'\n", otg->gadget->name); /* optionally disable D+ pullup */ - if (gpio_is_valid(gpio)) - gpio_set_value(gpio, pdata->gpio_pullup_inverted); + if (gpio_vbus->pullup_gpiod) + gpiod_set_value(gpio_vbus->pullup_gpiod, 0); set_vbus_draw(gpio_vbus, 0); @@ -242,16 +230,12 @@ static int gpio_vbus_set_suspend(struct usb_phy *phy, int suspend) static int gpio_vbus_probe(struct platform_device *pdev) { - struct gpio_vbus_mach_info *pdata = dev_get_platdata(&pdev->dev); struct gpio_vbus_data *gpio_vbus; struct resource *res; - int err, gpio, irq; + struct device *dev = &pdev->dev; + int err, irq; unsigned long irqflags; - if (!pdata || !gpio_is_valid(pdata->gpio_vbus)) - return -EINVAL; - gpio = pdata->gpio_vbus; - gpio_vbus = devm_kzalloc(&pdev->dev, sizeof(struct gpio_vbus_data), GFP_KERNEL); if (!gpio_vbus) @@ -273,37 +257,43 @@ static int gpio_vbus_probe(struct platform_device *pdev) gpio_vbus->phy.otg->usb_phy = &gpio_vbus->phy; gpio_vbus->phy.otg->set_peripheral = gpio_vbus_set_peripheral; - err = devm_gpio_request(&pdev->dev, gpio, "vbus_detect"); - if (err) { - dev_err(&pdev->dev, "can't request vbus gpio %d, err: %d\n", - gpio, err); + /* Look up the VBUS sensing GPIO */ + gpio_vbus->vbus_gpiod = devm_gpiod_get(dev, "vbus", GPIOD_IN); + if (IS_ERR(gpio_vbus->vbus_gpiod)) { + err = PTR_ERR(gpio_vbus->vbus_gpiod); + dev_err(&pdev->dev, "can't request vbus gpio, err: %d\n", err); return err; } - gpio_direction_input(gpio); + gpiod_set_consumer_name(gpio_vbus->vbus_gpiod, "vbus_detect"); res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); if (res) { irq = res->start; irqflags = (res->flags & IRQF_TRIGGER_MASK) | IRQF_SHARED; } else { - irq = gpio_to_irq(gpio); + irq = gpiod_to_irq(gpio_vbus->vbus_gpiod); irqflags = VBUS_IRQ_FLAGS; } gpio_vbus->irq = irq; - /* if data line pullup is in use, initialize it to "not pulling up" */ - gpio = pdata->gpio_pullup; - if (gpio_is_valid(gpio)) { - err = devm_gpio_request(&pdev->dev, gpio, "udc_pullup"); - if (err) { - dev_err(&pdev->dev, - "can't request pullup gpio %d, err: %d\n", - gpio, err); - return err; - } - gpio_direction_output(gpio, pdata->gpio_pullup_inverted); + /* + * The VBUS sensing GPIO should have a pulldown, which will normally be + * part of a resistor ladder turning a 4.0V-5.25V level on VBUS into a + * value the GPIO detects as active. Some systems will use comparators. + * Get the optional D+ or D- pullup GPIO. If the data line pullup is + * in use, initialize it to "not pulling up" + */ + gpio_vbus->pullup_gpiod = devm_gpiod_get_optional(dev, "pullup", + GPIOD_OUT_LOW); + if (IS_ERR(gpio_vbus->pullup_gpiod)) { + err = PTR_ERR(gpio_vbus->pullup_gpiod); + dev_err(&pdev->dev, "can't request pullup gpio, err: %d\n", + err); + return err; } + if (gpio_vbus->pullup_gpiod) + gpiod_set_consumer_name(gpio_vbus->pullup_gpiod, "udc_pullup"); err = devm_request_irq(&pdev->dev, irq, gpio_vbus_irq, irqflags, "vbus_detect", pdev); @@ -330,7 +320,7 @@ static int gpio_vbus_probe(struct platform_device *pdev) return err; } - device_init_wakeup(&pdev->dev, pdata->wakeup); + /* TODO: wakeup could be enabled here with device_init_wakeup(dev, 1) */ return 0; } diff --git a/drivers/usb/phy/phy-keystone.c b/drivers/usb/phy/phy-keystone.c index 110e6e9ad621..9c226b57153b 100644 --- a/drivers/usb/phy/phy-keystone.c +++ b/drivers/usb/phy/phy-keystone.c @@ -76,7 +76,7 @@ static int keystone_usbphy_probe(struct platform_device *pdev) if (IS_ERR(k_phy->phy_ctrl)) return PTR_ERR(k_phy->phy_ctrl); - ret = usb_phy_gen_create_phy(dev, &k_phy->usb_phy_gen, NULL); + ret = usb_phy_gen_create_phy(dev, &k_phy->usb_phy_gen); if (ret) return ret; diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c index ea7ef1dc0b42..037e8eee737d 100644 --- a/drivers/usb/phy/phy-tegra-usb.c +++ b/drivers/usb/phy/phy-tegra-usb.c @@ -9,54 +9,56 @@ * Venu Byravarasu <vbyravarasu@nvidia.com> */ -#include <linux/resource.h> #include <linux/delay.h> -#include <linux/slab.h> #include <linux/err.h> #include <linux/export.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <linux/iopoll.h> #include <linux/gpio.h> +#include <linux/iopoll.h> +#include <linux/module.h> #include <linux/of.h> #include <linux/of_device.h> #include <linux/of_gpio.h> -#include <linux/usb/otg.h> -#include <linux/usb/ulpi.h> -#include <linux/usb/of.h> +#include <linux/platform_device.h> +#include <linux/resource.h> +#include <linux/slab.h> +#include <linux/spinlock.h> + +#include <linux/regulator/consumer.h> + #include <linux/usb/ehci_def.h> +#include <linux/usb/of.h> #include <linux/usb/tegra_usb_phy.h> -#include <linux/regulator/consumer.h> +#include <linux/usb/ulpi.h> -#define ULPI_VIEWPORT 0x170 +#define ULPI_VIEWPORT 0x170 /* PORTSC PTS/PHCD bits, Tegra20 only */ -#define TEGRA_USB_PORTSC1 0x184 -#define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30) -#define TEGRA_USB_PORTSC1_PHCD (1 << 23) +#define TEGRA_USB_PORTSC1 0x184 +#define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30) +#define TEGRA_USB_PORTSC1_PHCD BIT(23) /* HOSTPC1 PTS/PHCD bits, Tegra30 and above */ -#define TEGRA_USB_HOSTPC1_DEVLC 0x1b4 -#define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29) -#define TEGRA_USB_HOSTPC1_DEVLC_PHCD (1 << 22) +#define TEGRA_USB_HOSTPC1_DEVLC 0x1b4 +#define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29) +#define TEGRA_USB_HOSTPC1_DEVLC_PHCD BIT(22) /* Bits of PORTSC1, which will get cleared by writing 1 into them */ #define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC) -#define USB_SUSP_CTRL 0x400 -#define USB_WAKE_ON_CNNT_EN_DEV (1 << 3) -#define USB_WAKE_ON_DISCON_EN_DEV (1 << 4) -#define USB_SUSP_CLR (1 << 5) -#define USB_PHY_CLK_VALID (1 << 7) -#define UTMIP_RESET (1 << 11) -#define UHSIC_RESET (1 << 11) -#define UTMIP_PHY_ENABLE (1 << 12) -#define ULPI_PHY_ENABLE (1 << 13) -#define USB_SUSP_SET (1 << 14) -#define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16) - -#define USB1_LEGACY_CTRL 0x410 -#define USB1_NO_LEGACY_MODE (1 << 0) +#define USB_SUSP_CTRL 0x400 +#define USB_WAKE_ON_CNNT_EN_DEV BIT(3) +#define USB_WAKE_ON_DISCON_EN_DEV BIT(4) +#define USB_SUSP_CLR BIT(5) +#define USB_PHY_CLK_VALID BIT(7) +#define UTMIP_RESET BIT(11) +#define UHSIC_RESET BIT(11) +#define UTMIP_PHY_ENABLE BIT(12) +#define ULPI_PHY_ENABLE BIT(13) +#define USB_SUSP_SET BIT(14) +#define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16) + +#define USB1_LEGACY_CTRL 0x410 +#define USB1_NO_LEGACY_MODE BIT(0) #define USB1_VBUS_SENSE_CTL_MASK (3 << 1) #define USB1_VBUS_SENSE_CTL_VBUS_WAKEUP (0 << 1) #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP \ @@ -64,94 +66,94 @@ #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD (2 << 1) #define USB1_VBUS_SENSE_CTL_A_SESS_VLD (3 << 1) -#define ULPI_TIMING_CTRL_0 0x424 -#define ULPI_OUTPUT_PINMUX_BYP (1 << 10) -#define ULPI_CLKOUT_PINMUX_BYP (1 << 11) +#define ULPI_TIMING_CTRL_0 0x424 +#define ULPI_OUTPUT_PINMUX_BYP BIT(10) +#define ULPI_CLKOUT_PINMUX_BYP BIT(11) -#define ULPI_TIMING_CTRL_1 0x428 -#define ULPI_DATA_TRIMMER_LOAD (1 << 0) -#define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1) -#define ULPI_STPDIRNXT_TRIMMER_LOAD (1 << 16) -#define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17) -#define ULPI_DIR_TRIMMER_LOAD (1 << 24) -#define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25) +#define ULPI_TIMING_CTRL_1 0x428 +#define ULPI_DATA_TRIMMER_LOAD BIT(0) +#define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1) +#define ULPI_STPDIRNXT_TRIMMER_LOAD BIT(16) +#define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17) +#define ULPI_DIR_TRIMMER_LOAD BIT(24) +#define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25) -#define UTMIP_PLL_CFG1 0x804 +#define UTMIP_PLL_CFG1 0x804 #define UTMIP_XTAL_FREQ_COUNT(x) (((x) & 0xfff) << 0) #define UTMIP_PLLU_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27) -#define UTMIP_XCVR_CFG0 0x808 +#define UTMIP_XCVR_CFG0 0x808 #define UTMIP_XCVR_SETUP(x) (((x) & 0xf) << 0) #define UTMIP_XCVR_SETUP_MSB(x) ((((x) & 0x70) >> 4) << 22) #define UTMIP_XCVR_LSRSLEW(x) (((x) & 0x3) << 8) #define UTMIP_XCVR_LSFSLEW(x) (((x) & 0x3) << 10) -#define UTMIP_FORCE_PD_POWERDOWN (1 << 14) -#define UTMIP_FORCE_PD2_POWERDOWN (1 << 16) -#define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18) -#define UTMIP_XCVR_LSBIAS_SEL (1 << 21) +#define UTMIP_FORCE_PD_POWERDOWN BIT(14) +#define UTMIP_FORCE_PD2_POWERDOWN BIT(16) +#define UTMIP_FORCE_PDZI_POWERDOWN BIT(18) +#define UTMIP_XCVR_LSBIAS_SEL BIT(21) #define UTMIP_XCVR_HSSLEW(x) (((x) & 0x3) << 4) #define UTMIP_XCVR_HSSLEW_MSB(x) ((((x) & 0x1fc) >> 2) << 25) -#define UTMIP_BIAS_CFG0 0x80c -#define UTMIP_OTGPD (1 << 11) -#define UTMIP_BIASPD (1 << 10) -#define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0) -#define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2) -#define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24) +#define UTMIP_BIAS_CFG0 0x80c +#define UTMIP_OTGPD BIT(11) +#define UTMIP_BIASPD BIT(10) +#define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0) +#define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2) +#define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24) -#define UTMIP_HSRX_CFG0 0x810 -#define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10) -#define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15) +#define UTMIP_HSRX_CFG0 0x810 +#define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10) +#define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15) -#define UTMIP_HSRX_CFG1 0x814 -#define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1) +#define UTMIP_HSRX_CFG1 0x814 +#define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1) -#define UTMIP_TX_CFG0 0x820 -#define UTMIP_FS_PREABMLE_J (1 << 19) -#define UTMIP_HS_DISCON_DISABLE (1 << 8) +#define UTMIP_TX_CFG0 0x820 +#define UTMIP_FS_PREABMLE_J BIT(19) +#define UTMIP_HS_DISCON_DISABLE BIT(8) -#define UTMIP_MISC_CFG0 0x824 -#define UTMIP_DPDM_OBSERVE (1 << 26) -#define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27) -#define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf) -#define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe) -#define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd) -#define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc) -#define UTMIP_SUSPEND_EXIT_ON_EDGE (1 << 22) +#define UTMIP_MISC_CFG0 0x824 +#define UTMIP_DPDM_OBSERVE BIT(26) +#define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27) +#define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf) +#define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe) +#define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd) +#define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc) +#define UTMIP_SUSPEND_EXIT_ON_EDGE BIT(22) -#define UTMIP_MISC_CFG1 0x828 -#define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18) -#define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6) +#define UTMIP_MISC_CFG1 0x828 +#define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18) +#define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6) -#define UTMIP_DEBOUNCE_CFG0 0x82c -#define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0) +#define UTMIP_DEBOUNCE_CFG0 0x82c +#define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0) -#define UTMIP_BAT_CHRG_CFG0 0x830 -#define UTMIP_PD_CHRG (1 << 0) +#define UTMIP_BAT_CHRG_CFG0 0x830 +#define UTMIP_PD_CHRG BIT(0) -#define UTMIP_SPARE_CFG0 0x834 -#define FUSE_SETUP_SEL (1 << 3) +#define UTMIP_SPARE_CFG0 0x834 +#define FUSE_SETUP_SEL BIT(3) -#define UTMIP_XCVR_CFG1 0x838 -#define UTMIP_FORCE_PDDISC_POWERDOWN (1 << 0) -#define UTMIP_FORCE_PDCHRP_POWERDOWN (1 << 2) -#define UTMIP_FORCE_PDDR_POWERDOWN (1 << 4) -#define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18) +#define UTMIP_XCVR_CFG1 0x838 +#define UTMIP_FORCE_PDDISC_POWERDOWN BIT(0) +#define UTMIP_FORCE_PDCHRP_POWERDOWN BIT(2) +#define UTMIP_FORCE_PDDR_POWERDOWN BIT(4) +#define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18) -#define UTMIP_BIAS_CFG1 0x83c -#define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3) +#define UTMIP_BIAS_CFG1 0x83c +#define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3) /* For Tegra30 and above only, the address is different in Tegra20 */ -#define USB_USBMODE 0x1f8 -#define USB_USBMODE_MASK (3 << 0) -#define USB_USBMODE_HOST (3 << 0) -#define USB_USBMODE_DEVICE (2 << 0) +#define USB_USBMODE 0x1f8 +#define USB_USBMODE_MASK (3 << 0) +#define USB_USBMODE_HOST (3 << 0) +#define USB_USBMODE_DEVICE (2 << 0) static DEFINE_SPINLOCK(utmip_pad_lock); -static int utmip_pad_count; +static unsigned int utmip_pad_count; struct tegra_xtal_freq { - int freq; + unsigned int freq; u8 enable_delay; u8 stable_count; u8 active_delay; @@ -194,43 +196,49 @@ static const struct tegra_xtal_freq tegra_freq_table[] = { }, }; +static inline struct tegra_usb_phy *to_tegra_usb_phy(struct usb_phy *u_phy) +{ + return container_of(u_phy, struct tegra_usb_phy, u_phy); +} + static void set_pts(struct tegra_usb_phy *phy, u8 pts_val) { void __iomem *base = phy->regs; - unsigned long val; + u32 val; if (phy->soc_config->has_hostpc) { - val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); + val = readl_relaxed(base + TEGRA_USB_HOSTPC1_DEVLC); val &= ~TEGRA_USB_HOSTPC1_DEVLC_PTS(~0); val |= TEGRA_USB_HOSTPC1_DEVLC_PTS(pts_val); - writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); + writel_relaxed(val, base + TEGRA_USB_HOSTPC1_DEVLC); } else { - val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS; + val = readl_relaxed(base + TEGRA_USB_PORTSC1); + val &= ~TEGRA_PORTSC1_RWC_BITS; val &= ~TEGRA_USB_PORTSC1_PTS(~0); val |= TEGRA_USB_PORTSC1_PTS(pts_val); - writel(val, base + TEGRA_USB_PORTSC1); + writel_relaxed(val, base + TEGRA_USB_PORTSC1); } } static void set_phcd(struct tegra_usb_phy *phy, bool enable) { void __iomem *base = phy->regs; - unsigned long val; + u32 val; if (phy->soc_config->has_hostpc) { - val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); + val = readl_relaxed(base + TEGRA_USB_HOSTPC1_DEVLC); if (enable) val |= TEGRA_USB_HOSTPC1_DEVLC_PHCD; else val &= ~TEGRA_USB_HOSTPC1_DEVLC_PHCD; - writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); + writel_relaxed(val, base + TEGRA_USB_HOSTPC1_DEVLC); } else { - val = readl(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS; + val = readl_relaxed(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS; if (enable) val |= TEGRA_USB_PORTSC1_PHCD; else val &= ~TEGRA_USB_PORTSC1_PHCD; - writel(val, base + TEGRA_USB_PORTSC1); + writel_relaxed(val, base + TEGRA_USB_PORTSC1); } } @@ -238,23 +246,6 @@ static int utmip_pad_open(struct tegra_usb_phy *phy) { int ret; - phy->pad_clk = devm_clk_get(phy->u_phy.dev, "utmi-pads"); - if (IS_ERR(phy->pad_clk)) { - ret = PTR_ERR(phy->pad_clk); - dev_err(phy->u_phy.dev, - "Failed to get UTMIP pad clock: %d\n", ret); - return ret; - } - - phy->pad_rst = devm_reset_control_get_optional_shared( - phy->u_phy.dev, "utmi-pads"); - if (IS_ERR(phy->pad_rst)) { - ret = PTR_ERR(phy->pad_rst); - dev_err(phy->u_phy.dev, - "Failed to get UTMI-pads reset: %d\n", ret); - return ret; - } - ret = clk_prepare_enable(phy->pad_clk); if (ret) { dev_err(phy->u_phy.dev, @@ -315,18 +306,21 @@ static int utmip_pad_close(struct tegra_usb_phy *phy) return ret; } -static void utmip_pad_power_on(struct tegra_usb_phy *phy) +static int utmip_pad_power_on(struct tegra_usb_phy *phy) { - unsigned long val, flags; - void __iomem *base = phy->pad_regs; struct tegra_utmip_config *config = phy->config; + void __iomem *base = phy->pad_regs; + u32 val; + int err; - clk_prepare_enable(phy->pad_clk); + err = clk_prepare_enable(phy->pad_clk); + if (err) + return err; - spin_lock_irqsave(&utmip_pad_lock, flags); + spin_lock(&utmip_pad_lock); if (utmip_pad_count++ == 0) { - val = readl(base + UTMIP_BIAS_CFG0); + val = readl_relaxed(base + UTMIP_BIAS_CFG0); val &= ~(UTMIP_OTGPD | UTMIP_BIASPD); if (phy->soc_config->requires_extra_tuning_parameters) { @@ -338,53 +332,59 @@ static void utmip_pad_power_on(struct tegra_usb_phy *phy) val |= UTMIP_HSDISCON_LEVEL(config->hsdiscon_level); val |= UTMIP_HSDISCON_LEVEL_MSB(config->hsdiscon_level); } - writel(val, base + UTMIP_BIAS_CFG0); + writel_relaxed(val, base + UTMIP_BIAS_CFG0); } - spin_unlock_irqrestore(&utmip_pad_lock, flags); + spin_unlock(&utmip_pad_lock); clk_disable_unprepare(phy->pad_clk); + + return 0; } static int utmip_pad_power_off(struct tegra_usb_phy *phy) { - unsigned long val, flags; void __iomem *base = phy->pad_regs; + u32 val; + int ret; + + ret = clk_prepare_enable(phy->pad_clk); + if (ret) + return ret; + + spin_lock(&utmip_pad_lock); if (!utmip_pad_count) { dev_err(phy->u_phy.dev, "UTMIP pad already powered off\n"); - return -EINVAL; + ret = -EINVAL; + goto ulock; } - clk_prepare_enable(phy->pad_clk); - - spin_lock_irqsave(&utmip_pad_lock, flags); - if (--utmip_pad_count == 0) { - val = readl(base + UTMIP_BIAS_CFG0); + val = readl_relaxed(base + UTMIP_BIAS_CFG0); val |= UTMIP_OTGPD | UTMIP_BIASPD; - writel(val, base + UTMIP_BIAS_CFG0); + writel_relaxed(val, base + UTMIP_BIAS_CFG0); } - - spin_unlock_irqrestore(&utmip_pad_lock, flags); +ulock: + spin_unlock(&utmip_pad_lock); clk_disable_unprepare(phy->pad_clk); - return 0; + return ret; } static int utmi_wait_register(void __iomem *reg, u32 mask, u32 result) { u32 tmp; - return readl_poll_timeout(reg, tmp, (tmp & mask) == result, - 2000, 6000); + return readl_relaxed_poll_timeout(reg, tmp, (tmp & mask) == result, + 2000, 6000); } static void utmi_phy_clk_disable(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; /* * The USB driver may have already initiated the phy clock @@ -395,27 +395,28 @@ static void utmi_phy_clk_disable(struct tegra_usb_phy *phy) return; if (phy->is_legacy_phy) { - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= USB_SUSP_SET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); - udelay(10); + usleep_range(10, 100); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~USB_SUSP_SET; - writel(val, base + USB_SUSP_CTRL); - } else + writel_relaxed(val, base + USB_SUSP_CTRL); + } else { set_phcd(phy, true); + } - if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) < 0) + if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0)) dev_err(phy->u_phy.dev, "Timeout waiting for PHY to stabilize on disable\n"); } static void utmi_phy_clk_enable(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; /* * The USB driver may have already initiated the phy clock @@ -427,97 +428,101 @@ static void utmi_phy_clk_enable(struct tegra_usb_phy *phy) return; if (phy->is_legacy_phy) { - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= USB_SUSP_CLR; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); - udelay(10); + usleep_range(10, 100); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~USB_SUSP_CLR; - writel(val, base + USB_SUSP_CTRL); - } else + writel_relaxed(val, base + USB_SUSP_CTRL); + } else { set_phcd(phy, false); + } if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, - USB_PHY_CLK_VALID)) + USB_PHY_CLK_VALID)) dev_err(phy->u_phy.dev, "Timeout waiting for PHY to stabilize on enable\n"); } static int utmi_phy_power_on(struct tegra_usb_phy *phy) { - unsigned long val; - void __iomem *base = phy->regs; struct tegra_utmip_config *config = phy->config; + void __iomem *base = phy->regs; + u32 val; + int err; - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= UTMIP_RESET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); if (phy->is_legacy_phy) { - val = readl(base + USB1_LEGACY_CTRL); + val = readl_relaxed(base + USB1_LEGACY_CTRL); val |= USB1_NO_LEGACY_MODE; - writel(val, base + USB1_LEGACY_CTRL); + writel_relaxed(val, base + USB1_LEGACY_CTRL); } - val = readl(base + UTMIP_TX_CFG0); + val = readl_relaxed(base + UTMIP_TX_CFG0); val |= UTMIP_FS_PREABMLE_J; - writel(val, base + UTMIP_TX_CFG0); + writel_relaxed(val, base + UTMIP_TX_CFG0); - val = readl(base + UTMIP_HSRX_CFG0); + val = readl_relaxed(base + UTMIP_HSRX_CFG0); val &= ~(UTMIP_IDLE_WAIT(~0) | UTMIP_ELASTIC_LIMIT(~0)); val |= UTMIP_IDLE_WAIT(config->idle_wait_delay); val |= UTMIP_ELASTIC_LIMIT(config->elastic_limit); - writel(val, base + UTMIP_HSRX_CFG0); + writel_relaxed(val, base + UTMIP_HSRX_CFG0); - val = readl(base + UTMIP_HSRX_CFG1); + val = readl_relaxed(base + UTMIP_HSRX_CFG1); val &= ~UTMIP_HS_SYNC_START_DLY(~0); val |= UTMIP_HS_SYNC_START_DLY(config->hssync_start_delay); - writel(val, base + UTMIP_HSRX_CFG1); + writel_relaxed(val, base + UTMIP_HSRX_CFG1); - val = readl(base + UTMIP_DEBOUNCE_CFG0); + val = readl_relaxed(base + UTMIP_DEBOUNCE_CFG0); val &= ~UTMIP_BIAS_DEBOUNCE_A(~0); val |= UTMIP_BIAS_DEBOUNCE_A(phy->freq->debounce); - writel(val, base + UTMIP_DEBOUNCE_CFG0); + writel_relaxed(val, base + UTMIP_DEBOUNCE_CFG0); - val = readl(base + UTMIP_MISC_CFG0); + val = readl_relaxed(base + UTMIP_MISC_CFG0); val &= ~UTMIP_SUSPEND_EXIT_ON_EDGE; - writel(val, base + UTMIP_MISC_CFG0); + writel_relaxed(val, base + UTMIP_MISC_CFG0); if (!phy->soc_config->utmi_pll_config_in_car_module) { - val = readl(base + UTMIP_MISC_CFG1); + val = readl_relaxed(base + UTMIP_MISC_CFG1); val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) | UTMIP_PLLU_STABLE_COUNT(~0)); val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) | UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count); - writel(val, base + UTMIP_MISC_CFG1); + writel_relaxed(val, base + UTMIP_MISC_CFG1); - val = readl(base + UTMIP_PLL_CFG1); + val = readl_relaxed(base + UTMIP_PLL_CFG1); val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) | UTMIP_PLLU_ENABLE_DLY_COUNT(~0)); val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) | UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay); - writel(val, base + UTMIP_PLL_CFG1); + writel_relaxed(val, base + UTMIP_PLL_CFG1); } if (phy->mode == USB_DR_MODE_PERIPHERAL) { - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV); - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); - val = readl(base + UTMIP_BAT_CHRG_CFG0); + val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); val &= ~UTMIP_PD_CHRG; - writel(val, base + UTMIP_BAT_CHRG_CFG0); + writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); } else { - val = readl(base + UTMIP_BAT_CHRG_CFG0); + val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); val |= UTMIP_PD_CHRG; - writel(val, base + UTMIP_BAT_CHRG_CFG0); + writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); } - utmip_pad_power_on(phy); + err = utmip_pad_power_on(phy); + if (err) + return err; - val = readl(base + UTMIP_XCVR_CFG0); + val = readl_relaxed(base + UTMIP_XCVR_CFG0); val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN | UTMIP_XCVR_LSBIAS_SEL | UTMIP_XCVR_SETUP(~0) | UTMIP_XCVR_SETUP_MSB(~0) | @@ -535,57 +540,57 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy) val |= UTMIP_XCVR_HSSLEW(config->xcvr_hsslew); val |= UTMIP_XCVR_HSSLEW_MSB(config->xcvr_hsslew); } - writel(val, base + UTMIP_XCVR_CFG0); + writel_relaxed(val, base + UTMIP_XCVR_CFG0); - val = readl(base + UTMIP_XCVR_CFG1); + val = readl_relaxed(base + UTMIP_XCVR_CFG1); val &= ~(UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN | UTMIP_XCVR_TERM_RANGE_ADJ(~0)); val |= UTMIP_XCVR_TERM_RANGE_ADJ(config->term_range_adj); - writel(val, base + UTMIP_XCVR_CFG1); + writel_relaxed(val, base + UTMIP_XCVR_CFG1); - val = readl(base + UTMIP_BIAS_CFG1); + val = readl_relaxed(base + UTMIP_BIAS_CFG1); val &= ~UTMIP_BIAS_PDTRK_COUNT(~0); val |= UTMIP_BIAS_PDTRK_COUNT(0x5); - writel(val, base + UTMIP_BIAS_CFG1); + writel_relaxed(val, base + UTMIP_BIAS_CFG1); - val = readl(base + UTMIP_SPARE_CFG0); + val = readl_relaxed(base + UTMIP_SPARE_CFG0); if (config->xcvr_setup_use_fuses) val |= FUSE_SETUP_SEL; else val &= ~FUSE_SETUP_SEL; - writel(val, base + UTMIP_SPARE_CFG0); + writel_relaxed(val, base + UTMIP_SPARE_CFG0); if (!phy->is_legacy_phy) { - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= UTMIP_PHY_ENABLE; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); } - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~UTMIP_RESET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); if (phy->is_legacy_phy) { - val = readl(base + USB1_LEGACY_CTRL); + val = readl_relaxed(base + USB1_LEGACY_CTRL); val &= ~USB1_VBUS_SENSE_CTL_MASK; val |= USB1_VBUS_SENSE_CTL_A_SESS_VLD; - writel(val, base + USB1_LEGACY_CTRL); + writel_relaxed(val, base + USB1_LEGACY_CTRL); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~USB_SUSP_SET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); } utmi_phy_clk_enable(phy); if (phy->soc_config->requires_usbmode_setup) { - val = readl(base + USB_USBMODE); + val = readl_relaxed(base + USB_USBMODE); val &= ~USB_USBMODE_MASK; if (phy->mode == USB_DR_MODE_HOST) val |= USB_USBMODE_HOST; else val |= USB_USBMODE_DEVICE; - writel(val, base + USB_USBMODE); + writel_relaxed(val, base + USB_USBMODE); } if (!phy->is_legacy_phy) @@ -596,258 +601,252 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy) static int utmi_phy_power_off(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; utmi_phy_clk_disable(phy); if (phy->mode == USB_DR_MODE_PERIPHERAL) { - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0); val |= USB_WAKE_ON_CNNT_EN_DEV | USB_WAKEUP_DEBOUNCE_COUNT(5); - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); } - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= UTMIP_RESET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); - val = readl(base + UTMIP_BAT_CHRG_CFG0); + val = readl_relaxed(base + UTMIP_BAT_CHRG_CFG0); val |= UTMIP_PD_CHRG; - writel(val, base + UTMIP_BAT_CHRG_CFG0); + writel_relaxed(val, base + UTMIP_BAT_CHRG_CFG0); - val = readl(base + UTMIP_XCVR_CFG0); + val = readl_relaxed(base + UTMIP_XCVR_CFG0); val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN; - writel(val, base + UTMIP_XCVR_CFG0); + writel_relaxed(val, base + UTMIP_XCVR_CFG0); - val = readl(base + UTMIP_XCVR_CFG1); + val = readl_relaxed(base + UTMIP_XCVR_CFG1); val |= UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN; - writel(val, base + UTMIP_XCVR_CFG1); + writel_relaxed(val, base + UTMIP_XCVR_CFG1); return utmip_pad_power_off(phy); } static void utmi_phy_preresume(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; - val = readl(base + UTMIP_TX_CFG0); + val = readl_relaxed(base + UTMIP_TX_CFG0); val |= UTMIP_HS_DISCON_DISABLE; - writel(val, base + UTMIP_TX_CFG0); + writel_relaxed(val, base + UTMIP_TX_CFG0); } static void utmi_phy_postresume(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; - val = readl(base + UTMIP_TX_CFG0); + val = readl_relaxed(base + UTMIP_TX_CFG0); val &= ~UTMIP_HS_DISCON_DISABLE; - writel(val, base + UTMIP_TX_CFG0); + writel_relaxed(val, base + UTMIP_TX_CFG0); } static void utmi_phy_restore_start(struct tegra_usb_phy *phy, enum tegra_usb_phy_port_speed port_speed) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; - val = readl(base + UTMIP_MISC_CFG0); + val = readl_relaxed(base + UTMIP_MISC_CFG0); val &= ~UTMIP_DPDM_OBSERVE_SEL(~0); if (port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) val |= UTMIP_DPDM_OBSERVE_SEL_FS_K; else val |= UTMIP_DPDM_OBSERVE_SEL_FS_J; - writel(val, base + UTMIP_MISC_CFG0); - udelay(1); + writel_relaxed(val, base + UTMIP_MISC_CFG0); + usleep_range(1, 10); - val = readl(base + UTMIP_MISC_CFG0); + val = readl_relaxed(base + UTMIP_MISC_CFG0); val |= UTMIP_DPDM_OBSERVE; - writel(val, base + UTMIP_MISC_CFG0); - udelay(10); + writel_relaxed(val, base + UTMIP_MISC_CFG0); + usleep_range(10, 100); } static void utmi_phy_restore_end(struct tegra_usb_phy *phy) { - unsigned long val; void __iomem *base = phy->regs; + u32 val; - val = readl(base + UTMIP_MISC_CFG0); + val = readl_relaxed(base + UTMIP_MISC_CFG0); val &= ~UTMIP_DPDM_OBSERVE; - writel(val, base + UTMIP_MISC_CFG0); - udelay(10); + writel_relaxed(val, base + UTMIP_MISC_CFG0); + usleep_range(10, 100); } static int ulpi_phy_power_on(struct tegra_usb_phy *phy) { - int ret; - unsigned long val; void __iomem *base = phy->regs; + u32 val; + int err; - ret = gpio_direction_output(phy->reset_gpio, 0); - if (ret < 0) { - dev_err(phy->u_phy.dev, "GPIO %d not set to 0: %d\n", - phy->reset_gpio, ret); - return ret; - } - msleep(5); - ret = gpio_direction_output(phy->reset_gpio, 1); - if (ret < 0) { - dev_err(phy->u_phy.dev, "GPIO %d not set to 1: %d\n", - phy->reset_gpio, ret); - return ret; - } + gpiod_set_value_cansleep(phy->reset_gpio, 1); + + err = clk_prepare_enable(phy->clk); + if (err) + return err; + + usleep_range(5000, 6000); + + gpiod_set_value_cansleep(phy->reset_gpio, 0); - clk_prepare_enable(phy->clk); - msleep(1); + usleep_range(1000, 2000); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= UHSIC_RESET; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); - val = readl(base + ULPI_TIMING_CTRL_0); + val = readl_relaxed(base + ULPI_TIMING_CTRL_0); val |= ULPI_OUTPUT_PINMUX_BYP | ULPI_CLKOUT_PINMUX_BYP; - writel(val, base + ULPI_TIMING_CTRL_0); + writel_relaxed(val, base + ULPI_TIMING_CTRL_0); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= ULPI_PHY_ENABLE; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); val = 0; - writel(val, base + ULPI_TIMING_CTRL_1); + writel_relaxed(val, base + ULPI_TIMING_CTRL_1); val |= ULPI_DATA_TRIMMER_SEL(4); val |= ULPI_STPDIRNXT_TRIMMER_SEL(4); val |= ULPI_DIR_TRIMMER_SEL(4); - writel(val, base + ULPI_TIMING_CTRL_1); - udelay(10); + writel_relaxed(val, base + ULPI_TIMING_CTRL_1); + usleep_range(10, 100); val |= ULPI_DATA_TRIMMER_LOAD; val |= ULPI_STPDIRNXT_TRIMMER_LOAD; val |= ULPI_DIR_TRIMMER_LOAD; - writel(val, base + ULPI_TIMING_CTRL_1); + writel_relaxed(val, base + ULPI_TIMING_CTRL_1); /* Fix VbusInvalid due to floating VBUS */ - ret = usb_phy_io_write(phy->ulpi, 0x40, 0x08); - if (ret) { - dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret); - return ret; + err = usb_phy_io_write(phy->ulpi, 0x40, 0x08); + if (err) { + dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err); + goto disable_clk; } - ret = usb_phy_io_write(phy->ulpi, 0x80, 0x0B); - if (ret) { - dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret); - return ret; + err = usb_phy_io_write(phy->ulpi, 0x80, 0x0B); + if (err) { + dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err); + goto disable_clk; } - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val |= USB_SUSP_CLR; - writel(val, base + USB_SUSP_CTRL); - udelay(100); + writel_relaxed(val, base + USB_SUSP_CTRL); + usleep_range(100, 1000); - val = readl(base + USB_SUSP_CTRL); + val = readl_relaxed(base + USB_SUSP_CTRL); val &= ~USB_SUSP_CLR; - writel(val, base + USB_SUSP_CTRL); + writel_relaxed(val, base + USB_SUSP_CTRL); return 0; -} -static int ulpi_phy_power_off(struct tegra_usb_phy *phy) -{ - clk_disable(phy->clk); - return gpio_direction_output(phy->reset_gpio, 0); +disable_clk: + clk_disable_unprepare(phy->clk); + + return err; } -static void tegra_usb_phy_close(struct tegra_usb_phy *phy) +static int ulpi_phy_power_off(struct tegra_usb_phy *phy) { - if (!IS_ERR(phy->vbus)) - regulator_disable(phy->vbus); + gpiod_set_value_cansleep(phy->reset_gpio, 1); + usleep_range(5000, 6000); + clk_disable_unprepare(phy->clk); - if (!phy->is_ulpi_phy) - utmip_pad_close(phy); - - clk_disable_unprepare(phy->pll_u); + return 0; } static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) { + int err; + + if (phy->powered_on) + return 0; + if (phy->is_ulpi_phy) - return ulpi_phy_power_on(phy); + err = ulpi_phy_power_on(phy); else - return utmi_phy_power_on(phy); + err = utmi_phy_power_on(phy); + if (err) + return err; + + phy->powered_on = true; + + return 0; } static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy) { + int err; + + if (!phy->powered_on) + return 0; + if (phy->is_ulpi_phy) - return ulpi_phy_power_off(phy); + err = ulpi_phy_power_off(phy); else - return utmi_phy_power_off(phy); -} + err = utmi_phy_power_off(phy); + if (err) + return err; -static int tegra_usb_phy_suspend(struct usb_phy *x, int suspend) -{ - struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); - if (suspend) - return tegra_usb_phy_power_off(phy); - else - return tegra_usb_phy_power_on(phy); + phy->powered_on = false; + + return 0; } -static int ulpi_open(struct tegra_usb_phy *phy) +static void tegra_usb_phy_shutdown(struct usb_phy *u_phy) { - int err; + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); - phy->clk = devm_clk_get(phy->u_phy.dev, "ulpi-link"); - if (IS_ERR(phy->clk)) { - err = PTR_ERR(phy->clk); - dev_err(phy->u_phy.dev, "Failed to get ULPI clock: %d\n", err); - return err; - } + if (WARN_ON(!phy->freq)) + return; - err = devm_gpio_request(phy->u_phy.dev, phy->reset_gpio, - "ulpi_phy_reset_b"); - if (err < 0) { - dev_err(phy->u_phy.dev, "Request failed for GPIO %d: %d\n", - phy->reset_gpio, err); - return err; - } + tegra_usb_phy_power_off(phy); - err = gpio_direction_output(phy->reset_gpio, 0); - if (err < 0) { - dev_err(phy->u_phy.dev, - "GPIO %d direction not set to output: %d\n", - phy->reset_gpio, err); - return err; - } + if (!phy->is_ulpi_phy) + utmip_pad_close(phy); - phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0); - if (!phy->ulpi) { - dev_err(phy->u_phy.dev, "Failed to create ULPI OTG\n"); - err = -ENOMEM; - return err; - } + regulator_disable(phy->vbus); + clk_disable_unprepare(phy->pll_u); - phy->ulpi->io_priv = phy->regs + ULPI_VIEWPORT; - return 0; + phy->freq = NULL; } -static int tegra_usb_phy_init(struct tegra_usb_phy *phy) +static int tegra_usb_phy_set_suspend(struct usb_phy *u_phy, int suspend) { + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); + + if (WARN_ON(!phy->freq)) + return -EINVAL; + + if (suspend) + return tegra_usb_phy_power_off(phy); + else + return tegra_usb_phy_power_on(phy); +} + +static int tegra_usb_phy_init(struct usb_phy *u_phy) +{ + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); unsigned long parent_rate; - int i; + unsigned int i; int err; - phy->pll_u = devm_clk_get(phy->u_phy.dev, "pll_u"); - if (IS_ERR(phy->pll_u)) { - err = PTR_ERR(phy->pll_u); - dev_err(phy->u_phy.dev, - "Failed to get pll_u clock: %d\n", err); - return err; - } + if (WARN_ON(phy->freq)) + return 0; err = clk_prepare_enable(phy->pll_u); if (err) @@ -864,64 +863,74 @@ static int tegra_usb_phy_init(struct tegra_usb_phy *phy) dev_err(phy->u_phy.dev, "Invalid pll_u parent rate %ld\n", parent_rate); err = -EINVAL; - goto fail; + goto disable_clk; } - if (!IS_ERR(phy->vbus)) { - err = regulator_enable(phy->vbus); - if (err) { - dev_err(phy->u_phy.dev, - "Failed to enable USB VBUS regulator: %d\n", - err); - goto fail; - } + err = regulator_enable(phy->vbus); + if (err) { + dev_err(phy->u_phy.dev, + "Failed to enable USB VBUS regulator: %d\n", err); + goto disable_clk; } - if (phy->is_ulpi_phy) - err = ulpi_open(phy); - else + if (!phy->is_ulpi_phy) { err = utmip_pad_open(phy); - if (err < 0) - goto fail; + if (err) + goto disable_vbus; + } + + err = tegra_usb_phy_power_on(phy); + if (err) + goto close_phy; return 0; -fail: +close_phy: + if (!phy->is_ulpi_phy) + utmip_pad_close(phy); + +disable_vbus: + regulator_disable(phy->vbus); + +disable_clk: clk_disable_unprepare(phy->pll_u); + + phy->freq = NULL; + return err; } -void tegra_usb_phy_preresume(struct usb_phy *x) +void tegra_usb_phy_preresume(struct usb_phy *u_phy) { - struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); if (!phy->is_ulpi_phy) utmi_phy_preresume(phy); } EXPORT_SYMBOL_GPL(tegra_usb_phy_preresume); -void tegra_usb_phy_postresume(struct usb_phy *x) +void tegra_usb_phy_postresume(struct usb_phy *u_phy) { - struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); if (!phy->is_ulpi_phy) utmi_phy_postresume(phy); } EXPORT_SYMBOL_GPL(tegra_usb_phy_postresume); -void tegra_ehci_phy_restore_start(struct usb_phy *x, - enum tegra_usb_phy_port_speed port_speed) +void tegra_ehci_phy_restore_start(struct usb_phy *u_phy, + enum tegra_usb_phy_port_speed port_speed) { - struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); if (!phy->is_ulpi_phy) utmi_phy_restore_start(phy, port_speed); } EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_start); -void tegra_ehci_phy_restore_end(struct usb_phy *x) +void tegra_ehci_phy_restore_end(struct usb_phy *u_phy) { - struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy); if (!phy->is_ulpi_phy) utmi_phy_restore_end(phy); @@ -932,21 +941,25 @@ static int read_utmi_param(struct platform_device *pdev, const char *param, u8 *dest) { u32 value; - int err = of_property_read_u32(pdev->dev.of_node, param, &value); - *dest = (u8)value; - if (err < 0) + int err; + + err = of_property_read_u32(pdev->dev.of_node, param, &value); + if (err) dev_err(&pdev->dev, "Failed to read USB UTMI parameter %s: %d\n", param, err); + else + *dest = value; + return err; } static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, struct platform_device *pdev) { + struct tegra_utmip_config *config; struct resource *res; int err; - struct tegra_utmip_config *config; tegra_phy->is_ulpi_phy = false; @@ -957,7 +970,7 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, } tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start, - resource_size(res)); + resource_size(res)); if (!tegra_phy->pad_regs) { dev_err(&pdev->dev, "Failed to remap UTMI pad regs\n"); return -ENOMEM; @@ -971,49 +984,49 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, config = tegra_phy->config; err = read_utmi_param(pdev, "nvidia,hssync-start-delay", - &config->hssync_start_delay); - if (err < 0) + &config->hssync_start_delay); + if (err) return err; err = read_utmi_param(pdev, "nvidia,elastic-limit", - &config->elastic_limit); - if (err < 0) + &config->elastic_limit); + if (err) return err; err = read_utmi_param(pdev, "nvidia,idle-wait-delay", - &config->idle_wait_delay); - if (err < 0) + &config->idle_wait_delay); + if (err) return err; err = read_utmi_param(pdev, "nvidia,term-range-adj", - &config->term_range_adj); - if (err < 0) + &config->term_range_adj); + if (err) return err; err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew", - &config->xcvr_lsfslew); - if (err < 0) + &config->xcvr_lsfslew); + if (err) return err; err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew", - &config->xcvr_lsrslew); - if (err < 0) + &config->xcvr_lsrslew); + if (err) return err; if (tegra_phy->soc_config->requires_extra_tuning_parameters) { err = read_utmi_param(pdev, "nvidia,xcvr-hsslew", - &config->xcvr_hsslew); - if (err < 0) + &config->xcvr_hsslew); + if (err) return err; err = read_utmi_param(pdev, "nvidia,hssquelch-level", - &config->hssquelch_level); - if (err < 0) + &config->hssquelch_level); + if (err) return err; err = read_utmi_param(pdev, "nvidia,hsdiscon-level", - &config->hsdiscon_level); - if (err < 0) + &config->hsdiscon_level); + if (err) return err; } @@ -1022,8 +1035,8 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, if (!config->xcvr_setup_use_fuses) { err = read_utmi_param(pdev, "nvidia,xcvr-setup", - &config->xcvr_setup); - if (err < 0) + &config->xcvr_setup); + if (err) return err; } @@ -1053,23 +1066,20 @@ MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table); static int tegra_usb_phy_probe(struct platform_device *pdev) { - const struct of_device_id *match; - struct resource *res; - struct tegra_usb_phy *tegra_phy = NULL; struct device_node *np = pdev->dev.of_node; + struct tegra_usb_phy *tegra_phy; enum usb_phy_interface phy_type; + struct reset_control *reset; + struct gpio_desc *gpiod; + struct resource *res; + struct usb_phy *phy; int err; tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL); if (!tegra_phy) return -ENOMEM; - match = of_match_device(tegra_usb_phy_id_table, &pdev->dev); - if (!match) { - dev_err(&pdev->dev, "Error: No device match found\n"); - return -ENODEV; - } - tegra_phy->soc_config = match->data; + tegra_phy->soc_config = of_device_get_match_data(&pdev->dev); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res) { @@ -1078,7 +1088,7 @@ static int tegra_usb_phy_probe(struct platform_device *pdev) } tegra_phy->regs = devm_ioremap(&pdev->dev, res->start, - resource_size(res)); + resource_size(res)); if (!tegra_phy->regs) { dev_err(&pdev->dev, "Failed to remap I/O memory\n"); return -ENOMEM; @@ -1087,25 +1097,86 @@ static int tegra_usb_phy_probe(struct platform_device *pdev) tegra_phy->is_legacy_phy = of_property_read_bool(np, "nvidia,has-legacy-mode"); + if (of_find_property(np, "dr_mode", NULL)) + tegra_phy->mode = usb_get_dr_mode(&pdev->dev); + else + tegra_phy->mode = USB_DR_MODE_HOST; + + if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) { + dev_err(&pdev->dev, "dr_mode is invalid\n"); + return -EINVAL; + } + + /* On some boards, the VBUS regulator doesn't need to be controlled */ + tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus"); + if (IS_ERR(tegra_phy->vbus)) + return PTR_ERR(tegra_phy->vbus); + + tegra_phy->pll_u = devm_clk_get(&pdev->dev, "pll_u"); + err = PTR_ERR_OR_ZERO(tegra_phy->pll_u); + if (err) { + dev_err(&pdev->dev, "Failed to get pll_u clock: %d\n", err); + return err; + } + phy_type = of_usb_get_phy_mode(np); switch (phy_type) { case USBPHY_INTERFACE_MODE_UTMI: err = utmi_phy_probe(tegra_phy, pdev); - if (err < 0) + if (err) return err; + + tegra_phy->pad_clk = devm_clk_get(&pdev->dev, "utmi-pads"); + err = PTR_ERR_OR_ZERO(tegra_phy->pad_clk); + if (err) { + dev_err(&pdev->dev, + "Failed to get UTMIP pad clock: %d\n", err); + return err; + } + + reset = devm_reset_control_get_optional_shared(&pdev->dev, + "utmi-pads"); + err = PTR_ERR_OR_ZERO(reset); + if (err) { + dev_err(&pdev->dev, + "Failed to get UTMI-pads reset: %d\n", err); + return err; + } + tegra_phy->pad_rst = reset; break; case USBPHY_INTERFACE_MODE_ULPI: tegra_phy->is_ulpi_phy = true; - tegra_phy->reset_gpio = - of_get_named_gpio(np, "nvidia,phy-reset-gpio", 0); - if (!gpio_is_valid(tegra_phy->reset_gpio)) { + tegra_phy->clk = devm_clk_get(&pdev->dev, "ulpi-link"); + err = PTR_ERR_OR_ZERO(tegra_phy->clk); + if (err) { + dev_err(&pdev->dev, + "Failed to get ULPI clock: %d\n", err); + return err; + } + + gpiod = devm_gpiod_get_from_of_node(&pdev->dev, np, + "nvidia,phy-reset-gpio", + 0, GPIOD_OUT_HIGH, + "ulpi_phy_reset_b"); + err = PTR_ERR_OR_ZERO(gpiod); + if (err) { dev_err(&pdev->dev, - "Invalid GPIO: %d\n", tegra_phy->reset_gpio); - return tegra_phy->reset_gpio; + "Request failed for reset GPIO: %d\n", err); + return err; + } + tegra_phy->reset_gpio = gpiod; + + phy = devm_otg_ulpi_create(&pdev->dev, + &ulpi_viewport_access_ops, 0); + if (!phy) { + dev_err(&pdev->dev, "Failed to create ULPI OTG\n"); + return -ENOMEM; } - tegra_phy->config = NULL; + + tegra_phy->ulpi = phy; + tegra_phy->ulpi->io_priv = tegra_phy->regs + ULPI_VIEWPORT; break; default: @@ -1114,40 +1185,16 @@ static int tegra_usb_phy_probe(struct platform_device *pdev) return -EINVAL; } - if (of_find_property(np, "dr_mode", NULL)) - tegra_phy->mode = usb_get_dr_mode(&pdev->dev); - else - tegra_phy->mode = USB_DR_MODE_HOST; - - if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) { - dev_err(&pdev->dev, "dr_mode is invalid\n"); - return -EINVAL; - } - - /* On some boards, the VBUS regulator doesn't need to be controlled */ - if (of_find_property(np, "vbus-supply", NULL)) { - tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus"); - if (IS_ERR(tegra_phy->vbus)) - return PTR_ERR(tegra_phy->vbus); - } else { - dev_notice(&pdev->dev, "no vbus regulator"); - tegra_phy->vbus = ERR_PTR(-ENODEV); - } - tegra_phy->u_phy.dev = &pdev->dev; - err = tegra_usb_phy_init(tegra_phy); - if (err < 0) - return err; - - tegra_phy->u_phy.set_suspend = tegra_usb_phy_suspend; + tegra_phy->u_phy.init = tegra_usb_phy_init; + tegra_phy->u_phy.shutdown = tegra_usb_phy_shutdown; + tegra_phy->u_phy.set_suspend = tegra_usb_phy_set_suspend; platform_set_drvdata(pdev, tegra_phy); err = usb_add_phy_dev(&tegra_phy->u_phy); - if (err < 0) { - tegra_usb_phy_close(tegra_phy); + if (err) return err; - } return 0; } @@ -1157,7 +1204,6 @@ static int tegra_usb_phy_remove(struct platform_device *pdev) struct tegra_usb_phy *tegra_phy = platform_get_drvdata(pdev); usb_remove_phy(&tegra_phy->u_phy); - tegra_usb_phy_close(tegra_phy); return 0; } diff --git a/drivers/usb/phy/phy-ulpi.c b/drivers/usb/phy/phy-ulpi.c index a43c49369a60..e683a37e3a7a 100644 --- a/drivers/usb/phy/phy-ulpi.c +++ b/drivers/usb/phy/phy-ulpi.c @@ -240,6 +240,21 @@ static int ulpi_set_vbus(struct usb_otg *otg, bool on) return usb_phy_io_write(phy, flags, ULPI_OTG_CTRL); } +static void otg_ulpi_init(struct usb_phy *phy, struct usb_otg *otg, + struct usb_phy_io_ops *ops, + unsigned int flags) +{ + phy->label = "ULPI"; + phy->flags = flags; + phy->io_ops = ops; + phy->otg = otg; + phy->init = ulpi_init; + + otg->usb_phy = phy; + otg->set_host = ulpi_set_host; + otg->set_vbus = ulpi_set_vbus; +} + struct usb_phy * otg_ulpi_create(struct usb_phy_io_ops *ops, unsigned int flags) @@ -257,17 +272,32 @@ otg_ulpi_create(struct usb_phy_io_ops *ops, return NULL; } - phy->label = "ULPI"; - phy->flags = flags; - phy->io_ops = ops; - phy->otg = otg; - phy->init = ulpi_init; - - otg->usb_phy = phy; - otg->set_host = ulpi_set_host; - otg->set_vbus = ulpi_set_vbus; + otg_ulpi_init(phy, otg, ops, flags); return phy; } EXPORT_SYMBOL_GPL(otg_ulpi_create); +struct usb_phy * +devm_otg_ulpi_create(struct device *dev, + struct usb_phy_io_ops *ops, + unsigned int flags) +{ + struct usb_phy *phy; + struct usb_otg *otg; + + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); + if (!phy) + return NULL; + + otg = devm_kzalloc(dev, sizeof(*otg), GFP_KERNEL); + if (!otg) { + devm_kfree(dev, phy); + return NULL; + } + + otg_ulpi_init(phy, otg, ops, flags); + + return phy; +} +EXPORT_SYMBOL_GPL(devm_otg_ulpi_create); diff --git a/drivers/usb/phy/phy.c b/drivers/usb/phy/phy.c index 0277f62739a2..ad2554630889 100644 --- a/drivers/usb/phy/phy.c +++ b/drivers/usb/phy/phy.c @@ -34,6 +34,14 @@ struct phy_devm { struct notifier_block *nb; }; +static const char *const usb_chger_type[] = { + [UNKNOWN_TYPE] = "USB_CHARGER_UNKNOWN_TYPE", + [SDP_TYPE] = "USB_CHARGER_SDP_TYPE", + [CDP_TYPE] = "USB_CHARGER_CDP_TYPE", + [DCP_TYPE] = "USB_CHARGER_DCP_TYPE", + [ACA_TYPE] = "USB_CHARGER_ACA_TYPE", +}; + static struct usb_phy *__usb_find_phy(struct list_head *list, enum usb_phy_type type) { @@ -98,7 +106,8 @@ static void usb_phy_notify_charger_work(struct work_struct *work) { struct usb_phy *usb_phy = container_of(work, struct usb_phy, chg_work); char uchger_state[50] = { 0 }; - char *envp[] = { uchger_state, NULL }; + char uchger_type[50] = { 0 }; + char *envp[] = { uchger_state, uchger_type, NULL }; unsigned int min, max; switch (usb_phy->chg_state) { @@ -122,6 +131,8 @@ static void usb_phy_notify_charger_work(struct work_struct *work) return; } + snprintf(uchger_type, ARRAY_SIZE(uchger_type), + "USB_CHARGER_TYPE=%s", usb_chger_type[usb_phy->chg_type]); kobject_uevent_env(&usb_phy->dev->kobj, KOBJ_CHANGE, envp); } |