diff options
Diffstat (limited to 'drivers/video/fbdev/omap2/dss/Kconfig')
| -rw-r--r-- | drivers/video/fbdev/omap2/dss/Kconfig | 135 |
1 files changed, 0 insertions, 135 deletions
diff --git a/drivers/video/fbdev/omap2/dss/Kconfig b/drivers/video/fbdev/omap2/dss/Kconfig deleted file mode 100644 index d1fa730c7d54..000000000000 --- a/drivers/video/fbdev/omap2/dss/Kconfig +++ /dev/null @@ -1,135 +0,0 @@ -config OMAP2_DSS_INIT - bool - -menuconfig OMAP2_DSS - tristate "OMAP2+ Display Subsystem support" - select VIDEOMODE_HELPERS - select OMAP2_DSS_INIT - select HDMI - help - OMAP2+ Display Subsystem support. - -if OMAP2_DSS - -config OMAP2_DSS_DEBUG - bool "Debug support" - default n - help - This enables printing of debug messages. Alternatively, debug messages - can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting - appropriate flags in <debugfs>/dynamic_debug/control. - -config OMAP2_DSS_DEBUGFS - bool "Debugfs filesystem support" - depends on DEBUG_FS - default n - help - This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables - querying about clock configuration and register configuration of dss, - dispc, dsi, hdmi and rfbi. - -config OMAP2_DSS_COLLECT_IRQ_STATS - bool "Collect DSS IRQ statistics" - depends on OMAP2_DSS_DEBUGFS - default n - help - Collect DSS IRQ statistics, printable via debugfs. - - The statistics can be found from - <debugfs>/omapdss/dispc_irq for DISPC interrupts, and - <debugfs>/omapdss/dsi_irq for DSI interrupts. - -config OMAP2_DSS_DPI - bool "DPI support" - default y - help - DPI Interface. This is the Parallel Display Interface. - -config OMAP2_DSS_RFBI - bool "RFBI support" - depends on BROKEN - default n - help - MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas - Instrument's terminology). - - DBI is a bus between the host processor and a peripheral, - such as a display or a framebuffer chip. - - See http://www.mipi.org/ for DBI specifications. - -config OMAP2_DSS_VENC - bool "VENC support" - default y - help - OMAP Video Encoder support for S-Video and composite TV-out. - -config OMAP2_DSS_HDMI_COMMON - bool - -config OMAP4_DSS_HDMI - bool "HDMI support for OMAP4" - default y - select OMAP2_DSS_HDMI_COMMON - help - HDMI support for OMAP4 based SoCs. - -config OMAP5_DSS_HDMI - bool "HDMI support for OMAP5" - default n - select OMAP2_DSS_HDMI_COMMON - help - HDMI Interface for OMAP5 and similar cores. This adds the High - Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI - specification. - -config OMAP2_DSS_SDI - bool "SDI support" - default n - help - SDI (Serial Display Interface) support. - - SDI is a high speed one-way display serial bus between the host - processor and a display. - -config OMAP2_DSS_DSI - bool "DSI support" - default n - help - MIPI DSI (Display Serial Interface) support. - - DSI is a high speed half-duplex serial interface between the host - processor and a peripheral, such as a display or a framebuffer chip. - - See http://www.mipi.org/ for DSI specifications. - -config OMAP2_DSS_MIN_FCK_PER_PCK - int "Minimum FCK/PCK ratio (for scaling)" - range 0 32 - default 0 - help - This can be used to adjust the minimum FCK/PCK ratio. - - With this you can make sure that DISPC FCK is at least - n x PCK. Video plane scaling requires higher FCK than - normally. - - If this is set to 0, there's no extra constraint on the - DISPC FCK. However, the FCK will at minimum be - 2xPCK (if active matrix) or 3xPCK (if passive matrix). - - Max FCK is 173MHz, so this doesn't work if your PCK - is very high. - -config OMAP2_DSS_SLEEP_AFTER_VENC_RESET - bool "Sleep 20ms after VENC reset" - default y - help - There is a 20ms sleep after VENC reset which seemed to fix the - reset. The reason for the bug is unclear, and it's also unclear - on what platforms this happens. - - This option enables the sleep, and is enabled by default. You can - disable the sleep if it doesn't cause problems on your platform. - -endif |