diff options
Diffstat (limited to 'include/asm-blackfin/mach-bf533/anomaly.h')
| -rw-r--r-- | include/asm-blackfin/mach-bf533/anomaly.h | 437 |
1 files changed, 235 insertions, 202 deletions
diff --git a/include/asm-blackfin/mach-bf533/anomaly.h b/include/asm-blackfin/mach-bf533/anomaly.h index 2a63ffc250a1..caea0b0f8326 100644 --- a/include/asm-blackfin/mach-bf533/anomaly.h +++ b/include/asm-blackfin/mach-bf533/anomaly.h @@ -7,219 +7,252 @@ */ /* This file shoule be up to date with: - * - Revision U, May 17, 2006; ADSP-BF533 Blackfin Processor Anomaly List - * - Revision Y, May 17, 2006; ADSP-BF532 Blackfin Processor Anomaly List - * - Revision T, May 17, 2006; ADSP-BF531 Blackfin Processor Anomaly List + * - Revision X, March 23, 2007; ADSP-BF533 Blackfin Processor Anomaly List + * - Revision AB, March 23, 2007; ADSP-BF532 Blackfin Processor Anomaly List + * - Revision W, March 23, 2007; ADSP-BF531 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ #define _MACH_ANOMALY_H_ /* We do not support 0.1 or 0.2 silicon - sorry */ -#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2)) -#error Kernel will not work on BF533 Version 0.1 or 0.2 +#if __SILICON_REVISION__ < 3 +# error Kernel will not work on BF533 silicon version 0.0, 0.1, or 0.2 #endif -/* Issues that are common to 0.5, 0.4, and 0.3 silicon */ -#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) \ - || defined(CONFIG_BF_REV_0_3)) -#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in - * slot1 and store of a P register in slot 2 is not - * supported */ -#define ANOMALY_05000105 /* Watchpoint Status Register (WPSTAT) bits are set on - * every corresponding match */ -#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive - * Channel DMA stops */ -#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR - * registers. */ -#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out - * upper bits*/ -#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */ -#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame - * syncs */ -#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not - * functional */ -#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable - * state */ -#define ANOMALY_05000229 /* SPI Slave Boot Mode modifies registers */ -#define ANOMALY_05000272 /* Certain data cache write through modes fail for - * VDDint <=0.9V */ -#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */ -#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after - * an edge is detected may clear interrupt */ -#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause - * DMA system instability */ -#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is - * not restored */ -#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic - * control */ -#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when - * killed in a particular stage*/ -#define ANOMALY_05000311 /* Erroneous flag pin operations under specific - * sequences */ -#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC - * registers are interrupted */ -#define ANOMALY_05000313 /* PPI Is Level-Sensitive on First Transfer */ -#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously On - * Next System MMR Access */ -#define ANOMALY_05000319 /* Internal Voltage Regulator Values of 1.05V, 1.10V - * and 1.15V Not Allowed for LQFP Packages */ -#endif /* Issues that are common to 0.5, 0.4, and 0.3 silicon */ +#if defined(__ADSPBF531__) +# define ANOMALY_BF531 1 +#else +# define ANOMALY_BF531 0 +#endif +#if defined(__ADSPBF532__) +# define ANOMALY_BF532 1 +#else +# define ANOMALY_BF532 0 +#endif +#if defined(__ADSPBF533__) +# define ANOMALY_BF533 1 +#else +# define ANOMALY_BF533 0 +#endif -/* These issues only occur on 0.3 or 0.4 BF533 */ -#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3)) -#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not - * updated at the same time. */ -#define ANOMALY_05000158 /* Boot fails when data cache enabled: Data from a Data - * Cache Fill can be corrupted after or during - * Instruction DMA if certain core stalls exist */ -#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General - * Purpose TX or RX modes */ -#define ANOMALY_05000198 /* Failing SYSTEM MMR accesses when stalled by - * preceding memory read */ -#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during - * inactive channels in certain conditions */ -#define ANOMALY_05000202 /* Possible infinite stall with specific dual dag - * situation */ -#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */ -#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */ -#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect - * data*/ -#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate - * Differences in certain Conditions */ -#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */ -#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to - * hardware reset */ -#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or - * IDLE around a Change of Control causes - * unpredictable results */ -#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the - * shadow of a conditional branch */ -#define ANOMALY_05000246 /* Data CPLB's should prevent spurious hardware - * errors */ -#define ANOMALY_05000253 /* Maximum external clock speed for Timers */ -#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event - * interrupt not functional */ -#define ANOMALY_05000257 /* An interrupt or exception during short Hardware - * loops may cause the instruction fetch unit to - * malfunction */ -#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of - * the ICPLB Data registers differ */ -#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */ -#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */ -#define ANOMALY_05000262 /* Stores to data cache may be lost */ -#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */ -#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE - * instruction will cause an infinite stall in the - * second to last instruction in a hardware loop */ -#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on - * SPORT external receive and transmit clocks. */ -#define ANOMALY_05000269 /* High I/O activity causes the output voltage of the - * internal voltage regulator (VDDint) to increase. */ -#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the - * internal voltage regulator (VDDint) to decrease */ -#endif /* issues only occur on 0.3 or 0.4 BF533 */ +/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */ +#define ANOMALY_05000074 (1) +/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */ +#define ANOMALY_05000099 (__SILICON_REVISION__ < 5) +/* Watchpoint Status Register (WPSTAT) Bits Are Set on Every Corresponding Match */ +#define ANOMALY_05000105 (1) +/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */ +#define ANOMALY_05000119 (1) +/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ +#define ANOMALY_05000122 (1) +/* Instruction DMA Can Cause Data Cache Fills to Fail (Boot Implications) */ +#define ANOMALY_05000158 (__SILICON_REVISION__ < 5) +/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */ +#define ANOMALY_05000166 (1) +/* Turning Serial Ports on with External Frame Syncs */ +#define ANOMALY_05000167 (1) +/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */ +#define ANOMALY_05000179 (__SILICON_REVISION__ < 5) +/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */ +#define ANOMALY_05000180 (1) +/* Timer Pin Limitations for PPI TX Modes with External Frame Syncs */ +#define ANOMALY_05000183 (__SILICON_REVISION__ < 4) +/* False Protection Exceptions */ +#define ANOMALY_05000189 (__SILICON_REVISION__ < 4) +/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */ +#define ANOMALY_05000193 (__SILICON_REVISION__ < 4) +/* Restarting SPORT in Specific Modes May Cause Data Corruption */ +#define ANOMALY_05000194 (__SILICON_REVISION__ < 4) +/* Failing MMR Accesses When Stalled by Preceding Memory Read */ +#define ANOMALY_05000198 (__SILICON_REVISION__ < 5) +/* Current DMA Address Shows Wrong Value During Carry Fix */ +#define ANOMALY_05000199 (__SILICON_REVISION__ < 4) +/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */ +#define ANOMALY_05000200 (__SILICON_REVISION__ < 5) +/* Receive Frame Sync Not Ignored During Active Frames in SPORT Multi-Channel Mode */ +#define ANOMALY_05000201 (__SILICON_REVISION__ < 4) +/* Possible Infinite Stall with Specific Dual-DAG Situation */ +#define ANOMALY_05000202 (__SILICON_REVISION__ < 5) +/* Specific Sequence That Can Cause DMA Error or DMA Stopping */ +#define ANOMALY_05000203 (__SILICON_REVISION__ < 4) +/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */ +#define ANOMALY_05000204 (__SILICON_REVISION__ < 4 && ANOMALY_BF533) +/* Recovery from "Brown-Out" Condition */ +#define ANOMALY_05000207 (__SILICON_REVISION__ < 4) +/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */ +#define ANOMALY_05000208 (1) +/* Speed Path in Computational Unit Affects Certain Instructions */ +#define ANOMALY_05000209 (__SILICON_REVISION__ < 4) +/* UART TX Interrupt Masked Erroneously */ +#define ANOMALY_05000215 (__SILICON_REVISION__ < 5) +/* NMI Event at Boot Time Results in Unpredictable State */ +#define ANOMALY_05000219 (1) +/* Incorrect Pulse-Width of UART Start Bit */ +#define ANOMALY_05000225 (__SILICON_REVISION__ < 5) +/* Scratchpad Memory Bank Reads May Return Incorrect Data */ +#define ANOMALY_05000227 (__SILICON_REVISION__ < 5) +/* SPI Slave Boot Mode Modifies Registers from Reset Value */ +#define ANOMALY_05000229 (1) +/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */ +#define ANOMALY_05000230 (__SILICON_REVISION__ < 5) +/* UART STB Bit Incorrectly Affects Receiver Setting */ +#define ANOMALY_05000231 (__SILICON_REVISION__ < 5) +/* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */ +#define ANOMALY_05000233 (__SILICON_REVISION__ < 4) +/* Incorrect Revision Number in DSPID Register */ +#define ANOMALY_05000234 (__SILICON_REVISION__ == 4) +/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */ +#define ANOMALY_05000242 (__SILICON_REVISION__ < 4) +/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */ +#define ANOMALY_05000244 (__SILICON_REVISION__ < 5) +/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */ +#define ANOMALY_05000245 (1) +/* Data CPLBs Should Prevent Spurious Hardware Errors */ +#define ANOMALY_05000246 (__SILICON_REVISION__ < 5) +/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */ +#define ANOMALY_05000250 (__SILICON_REVISION__ == 4) +/* Maximum External Clock Speed for Timers */ +#define ANOMALY_05000253 (__SILICON_REVISION__ < 5) +/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */ +#define ANOMALY_05000254 (__SILICON_REVISION__ > 4) +/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */ +#define ANOMALY_05000255 (__SILICON_REVISION__ < 5) +/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */ +#define ANOMALY_05000257 (__SILICON_REVISION__ < 5) +/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */ +#define ANOMALY_05000258 (__SILICON_REVISION__ < 5) +/* ICPLB_STATUS MMR Register May Be Corrupted */ +#define ANOMALY_05000260 (__SILICON_REVISION__ < 5) +/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */ +#define ANOMALY_05000261 (__SILICON_REVISION__ < 5) +/* Stores To Data Cache May Be Lost */ +#define ANOMALY_05000262 (__SILICON_REVISION__ < 5) +/* Hardware Loop Corrupted When Taking an ICPLB Exception */ +#define ANOMALY_05000263 (__SILICON_REVISION__ < 5) +/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */ +#define ANOMALY_05000264 (__SILICON_REVISION__ < 5) +/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ +#define ANOMALY_05000265 (__SILICON_REVISION__ < 5) +/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */ +#define ANOMALY_05000269 (__SILICON_REVISION__ < 5) +/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */ +#define ANOMALY_05000270 (__SILICON_REVISION__ < 5) +/* Spontaneous Reset of Internal Voltage Regulator */ +#define ANOMALY_05000271 (__SILICON_REVISION__ < 4) +/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */ +#define ANOMALY_05000272 (1) +/* Writes to Synchronous SDRAM Memory May Be Lost */ +#define ANOMALY_05000273 (1) +/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */ +#define ANOMALY_05000276 (1) +/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */ +#define ANOMALY_05000277 (1) +/* Disabling Peripherals with DMA Running May Cause DMA System Instability */ +#define ANOMALY_05000278 (1) +/* False Hardware Error Exception When ISR Context Is Not Restored */ +#define ANOMALY_05000281 (1) +/* Memory DMA Corruption with 32-Bit Data and Traffic Control */ +#define ANOMALY_05000282 (1) +/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */ +#define ANOMALY_05000283 (1) +/* SPORTs May Receive Bad Data If FIFOs Fill Up */ +#define ANOMALY_05000288 (1) +/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */ +#define ANOMALY_05000301 (1) +/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */ +#define ANOMALY_05000302 (__SILICON_REVISION__ < 5) +/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */ +#define ANOMALY_05000305 (__SILICON_REVISION__ < 5) +/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */ +#define ANOMALY_05000306 (__SILICON_REVISION__ < 5) +/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */ +#define ANOMALY_05000310 (1) +/* Erroneous Flag (GPIO) Pin Operations under Specific Sequences */ +#define ANOMALY_05000311 (1) +/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */ +#define ANOMALY_05000312 (1) +/* PPI Is Level-Sensitive on First Transfer */ +#define ANOMALY_05000313 (1) +/* Killed System MMR Write Completes Erroneously On Next System MMR Access */ +#define ANOMALY_05000315 (1) +/* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */ +#define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532) -/* These issues are only on 0.4 silicon */ -#if (defined(CONFIG_BF_REV_0_4)) -#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */ -#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel - * (TDM) */ -#endif /* issues are only on 0.4 silicon */ +/* These anomalies have been "phased" out of analog.com anomaly sheets and are + * here to show running on older silicon just isn't feasible. + */ -/* These issues are only on 0.3 silicon */ -#if defined(CONFIG_BF_REV_0_3) -#define ANOMALY_05000183 /* Timer Pin limitations for PPI TX Modes with - * External Frame Syncs */ -#define ANOMALY_05000189 /* False Protection Exceptions caused by Speculative - * Instruction or Data Fetches, or by Fetches at the - * boundary of reserved memory space */ -#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs - * when polarity setting is changed */ -#define ANOMALY_05000194 /* Sport Restarting in specific modes may cause data - * corruption */ -#define ANOMALY_05000199 /* DMA current address shows wrong value during carry - * fix */ -#define ANOMALY_05000201 /* Receive frame sync not ignored during active - * frames in sport MCM */ -#define ANOMALY_05000203 /* Specific sequence that can cause DMA error or DMA - * stopping */ -#if defined(CONFIG_BF533) -#define ANOMALY_05000204 /* Incorrect data read with write-through cache and - * allocate cache lines on reads only mode */ -#endif /* CONFIG_BF533 */ -#define ANOMALY_05000207 /* Recovery from "brown-out" condition */ -#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain - * instructions */ -#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame - * Sync Transmit Mode */ -#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */ -#endif /* only on 0.3 silicon */ +/* Watchpoints (Hardware Breakpoints) are not supported */ +#define ANOMALY_05000067 (__SILICON_REVISION__ < 3) +/* Reserved bits in SYSCFG register not set at power on */ +#define ANOMALY_05000109 (__SILICON_REVISION__ < 3) +/* Trace Buffers may record discontinuities into emulation mode and/or exception, NMI, reset handlers */ +#define ANOMALY_05000116 (__SILICON_REVISION__ < 3) +/* DTEST_COMMAND initiated memory access may be incorrect if data cache or DMA is active */ +#define ANOMALY_05000123 (__SILICON_REVISION__ < 3) +/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */ +#define ANOMALY_05000124 (__SILICON_REVISION__ < 3) +/* Erroneous exception when enabling cache */ +#define ANOMALY_05000125 (__SILICON_REVISION__ < 3) +/* SPI clock polarity and phase bits incorrect during booting */ +#define ANOMALY_05000126 (__SILICON_REVISION__ < 3) +/* DMEM_CONTROL is not set on Reset */ +#define ANOMALY_05000137 (__SILICON_REVISION__ < 3) +/* SPI boot will not complete if there is a zero fill block in the loader file */ +#define ANOMALY_05000138 (__SILICON_REVISION__ < 3) +/* Allowing the SPORT RX FIFO to fill will cause an overflow */ +#define ANOMALY_05000140 (__SILICON_REVISION__ < 3) +/* An Infinite Stall occurs with a particular sequence of consecutive dual dag events */ +#define ANOMALY_05000141 (__SILICON_REVISION__ < 3) +/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */ +#define ANOMALY_05000142 (__SILICON_REVISION__ < 3) +/* A read from external memory may return a wrong value with data cache enabled */ +#define ANOMALY_05000143 (__SILICON_REVISION__ < 3) +/* DMA and TESTSET conflict when both are accessing external memory */ +#define ANOMALY_05000144 (__SILICON_REVISION__ < 3) +/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */ +#define ANOMALY_05000145 (__SILICON_REVISION__ < 3) +/* MDMA may lose the first few words of a descriptor chain */ +#define ANOMALY_05000146 (__SILICON_REVISION__ < 3) +/* The source MDMA descriptor may stop with a DMA Error */ +#define ANOMALY_05000147 (__SILICON_REVISION__ < 3) +/* When booting from a 16-bit asynchronous memory device, the upper 8-bits of each word must be 0x00 */ +#define ANOMALY_05000148 (__SILICON_REVISION__ < 3) +/* Frame Delay in SPORT Multichannel Mode */ +#define ANOMALY_05000153 (__SILICON_REVISION__ < 3) +/* SPORT TFS signal is active in Multi-channel mode outside of valid channels */ +#define ANOMALY_05000154 (__SILICON_REVISION__ < 3) +/* Timer1 can not be used for PWMOUT mode when a certain PPI mode is in use */ +#define ANOMALY_05000155 (__SILICON_REVISION__ < 3) +/* A killed 32-bit System MMR write will lead to the next system MMR access thinking it should be 32-bit. */ +#define ANOMALY_05000157 (__SILICON_REVISION__ < 3) +/* SPORT transmit data is not gated by external frame sync in certain conditions */ +#define ANOMALY_05000163 (__SILICON_REVISION__ < 3) +/* SDRAM auto-refresh and subsequent Power Ups */ +#define ANOMALY_05000168 (__SILICON_REVISION__ < 3) +/* DATA CPLB page miss can result in lost write-through cache data writes */ +#define ANOMALY_05000169 (__SILICON_REVISION__ < 3) +/* DMA vs Core accesses to external memory */ +#define ANOMALY_05000173 (__SILICON_REVISION__ < 3) +/* Cache Fill Buffer Data lost */ +#define ANOMALY_05000174 (__SILICON_REVISION__ < 3) +/* Overlapping Sequencer and Memory Stalls */ +#define ANOMALY_05000175 (__SILICON_REVISION__ < 3) +/* Multiplication of (-1) by (-1) followed by an accumulator saturation */ +#define ANOMALY_05000176 (__SILICON_REVISION__ < 3) +/* Disabling the PPI resets the PPI configuration registers */ +#define ANOMALY_05000181 (__SILICON_REVISION__ < 3) +/* PPI TX Mode with 2 External Frame Syncs */ +#define ANOMALY_05000185 (__SILICON_REVISION__ < 3) +/* PPI does not invert the Driving PPICLK edge in Transmit Modes */ +#define ANOMALY_05000191 (__SILICON_REVISION__ < 3) +/* In PPI Transmit Modes with External Frame Syncs POLC */ +#define ANOMALY_05000192 (__SILICON_REVISION__ < 3) +/* Internal Voltage Regulator may not start up */ +#define ANOMALY_05000206 (__SILICON_REVISION__ < 3) -#if defined(CONFIG_BF_REV_0_2) -#define ANOMALY_05000067 /* Watchpoints (Hardware Breakpoints) are not - * supported */ -#define ANOMALY_05000109 /* Reserved bits in SYSCFG register not set at - * power on */ -#define ANOMALY_05000116 /* Trace Buffers may record discontinuities into - * emulation mode and/or exception, NMI, reset - * handlers */ -#define ANOMALY_05000123 /* DTEST_COMMAND initiated memory access may be - * incorrect if data cache or DMA is active */ -#define ANOMALY_05000124 /* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, - * or 1:1 */ -#define ANOMALY_05000125 /* Erroneous exception when enabling cache */ -#define ANOMALY_05000126 /* SPI clock polarity and phase bits incorrect - * during booting */ -#define ANOMALY_05000137 /* DMEM_CONTROL is not set on Reset */ -#define ANOMALY_05000138 /* SPI boot will not complete if there is a zero fill - * block in the loader file */ -#define ANOMALY_05000140 /* Allowing the SPORT RX FIFO to fill will cause an - * overflow */ -#define ANOMALY_05000141 /* An Infinite Stall occurs with a particular sequence - * of consecutive dual dag events */ -#define ANOMALY_05000142 /* Interrupts may be lost when a programmable input - * flag is configured to be edge sensitive */ -#define ANOMALY_05000143 /* A read from external memory may return a wrong - * value with data cache enabled */ -#define ANOMALY_05000144 /* DMA and TESTSET conflict when both are accessing - * external memory */ -#define ANOMALY_05000145 /* In PWM_OUT mode, you must enable the PPI block to - * generate a waveform from PPI_CLK */ -#define ANOMALY_05000146 /* MDMA may lose the first few words of a descriptor - * chain */ -#define ANOMALY_05000147 /* The source MDMA descriptor may stop with a DMA - * Error */ -#define ANOMALY_05000148 /* When booting from a 16-bit asynchronous memory - * device, the upper 8-bits of each word must be - * 0x00 */ -#define ANOMALY_05000153 /* Frame Delay in SPORT Multichannel Mode */ -#define ANOMALY_05000154 /* SPORT TFS signal is active in Multi-channel mode - * outside of valid channels */ -#define ANOMALY_05000155 /* Timer1 can not be used for PWMOUT mode when a - * certain PPI mode is in use */ -#define ANOMALY_05000157 /* A killed 32-bit System MMR write will lead to - * the next system MMR access thinking it should be - * 32-bit. */ -#define ANOMALY_05000163 /* SPORT transmit data is not gated by external frame - * sync in certain conditions */ -#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */ -#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost - * write-through cache data writes */ -#define ANOMALY_05000173 /* DMA vs Core accesses to external memory */ -#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */ -#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */ -#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an - * accumulator saturation */ -#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration - * registers */ -#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */ -#define ANOMALY_05000191 /* PPI does not invert the Driving PPICLK edge in - * Transmit Modes */ -#define ANOMALY_05000192 /* In PPI Transmit Modes with External Frame Syncs - * POLC */ -#define ANOMALY_05000206 /* Internal Voltage Regulator may not start up */ +/* Anomalies that don't exist on this proc */ +#define ANOMALY_05000266 (0) #endif - -#endif /* _MACH_ANOMALY_H_ */ |