diff options
Diffstat (limited to 'include/linux/phy.h')
| -rw-r--r-- | include/linux/phy.h | 925 |
1 files changed, 711 insertions, 214 deletions
diff --git a/include/linux/phy.h b/include/linux/phy.h index 452e8ba8665f..ddf66198f751 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -15,6 +15,7 @@ #include <linux/spinlock.h> #include <linux/ethtool.h> #include <linux/linkmode.h> +#include <linux/netlink.h> #include <linux/mdio.h> #include <linux/mii.h> #include <linux/mii_timestamper.h> @@ -23,6 +24,9 @@ #include <linux/workqueue.h> #include <linux/mod_devicetable.h> #include <linux/u64_stats_sync.h> +#include <linux/irqreturn.h> +#include <linux/iopoll.h> +#include <linux/refcount.h> #include <linux/atomic.h> @@ -61,23 +65,62 @@ extern const int phy_basic_ports_array[3]; extern const int phy_fibre_port_array[1]; extern const int phy_all_ports_features_array[7]; extern const int phy_10_100_features_array[4]; -extern const int phy_basic_t1_features_array[2]; +extern const int phy_basic_t1_features_array[3]; extern const int phy_gbit_features_array[2]; extern const int phy_10gbit_features_array[1]; /* * Set phydev->irq to PHY_POLL if interrupts are not supported, - * or not desired for this PHY. Set to PHY_IGNORE_INTERRUPT if - * the attached driver handles the interrupt + * or not desired for this PHY. Set to PHY_MAC_INTERRUPT if + * the attached MAC driver handles the interrupt */ #define PHY_POLL -1 -#define PHY_IGNORE_INTERRUPT -2 +#define PHY_MAC_INTERRUPT -2 #define PHY_IS_INTERNAL 0x00000001 #define PHY_RST_AFTER_CLK_EN 0x00000002 +#define PHY_POLL_CABLE_TEST 0x00000004 #define MDIO_DEVICE_IS_PHY 0x80000000 -/* Interface Mode definitions */ +/** + * enum phy_interface_t - Interface Mode definitions + * + * @PHY_INTERFACE_MODE_NA: Not Applicable - don't touch + * @PHY_INTERFACE_MODE_INTERNAL: No interface, MAC and PHY combined + * @PHY_INTERFACE_MODE_MII: Media-independent interface + * @PHY_INTERFACE_MODE_GMII: Gigabit media-independent interface + * @PHY_INTERFACE_MODE_SGMII: Serial gigabit media-independent interface + * @PHY_INTERFACE_MODE_TBI: Ten Bit Interface + * @PHY_INTERFACE_MODE_REVMII: Reverse Media Independent Interface + * @PHY_INTERFACE_MODE_RMII: Reduced Media Independent Interface + * @PHY_INTERFACE_MODE_REVRMII: Reduced Media Independent Interface in PHY role + * @PHY_INTERFACE_MODE_RGMII: Reduced gigabit media-independent interface + * @PHY_INTERFACE_MODE_RGMII_ID: RGMII with Internal RX+TX delay + * @PHY_INTERFACE_MODE_RGMII_RXID: RGMII with Internal RX delay + * @PHY_INTERFACE_MODE_RGMII_TXID: RGMII with Internal RX delay + * @PHY_INTERFACE_MODE_RTBI: Reduced TBI + * @PHY_INTERFACE_MODE_SMII: Serial MII + * @PHY_INTERFACE_MODE_XGMII: 10 gigabit media-independent interface + * @PHY_INTERFACE_MODE_XLGMII:40 gigabit media-independent interface + * @PHY_INTERFACE_MODE_MOCA: Multimedia over Coax + * @PHY_INTERFACE_MODE_QSGMII: Quad SGMII + * @PHY_INTERFACE_MODE_TRGMII: Turbo RGMII + * @PHY_INTERFACE_MODE_100BASEX: 100 BaseX + * @PHY_INTERFACE_MODE_1000BASEX: 1000 BaseX + * @PHY_INTERFACE_MODE_2500BASEX: 2500 BaseX + * @PHY_INTERFACE_MODE_5GBASER: 5G BaseR + * @PHY_INTERFACE_MODE_RXAUI: Reduced XAUI + * @PHY_INTERFACE_MODE_XAUI: 10 Gigabit Attachment Unit Interface + * @PHY_INTERFACE_MODE_10GBASER: 10G BaseR + * @PHY_INTERFACE_MODE_25GBASER: 25G BaseR + * @PHY_INTERFACE_MODE_USXGMII: Universal Serial 10GE MII + * @PHY_INTERFACE_MODE_10GKR: 10GBASE-KR - with Clause 73 AN + * @PHY_INTERFACE_MODE_QUSGMII: Quad Universal SGMII + * @PHY_INTERFACE_MODE_1000BASEKX: 1000Base-KX - with Clause 73 AN + * @PHY_INTERFACE_MODE_MAX: Book keeping + * + * Describes the interface between the MAC and PHY. + */ typedef enum { PHY_INTERFACE_MODE_NA, PHY_INTERFACE_MODE_INTERNAL, @@ -87,6 +130,7 @@ typedef enum { PHY_INTERFACE_MODE_TBI, PHY_INTERFACE_MODE_REVMII, PHY_INTERFACE_MODE_RMII, + PHY_INTERFACE_MODE_REVRMII, PHY_INTERFACE_MODE_RGMII, PHY_INTERFACE_MODE_RGMII_ID, PHY_INTERFACE_MODE_RGMII_RXID, @@ -94,31 +138,63 @@ typedef enum { PHY_INTERFACE_MODE_RTBI, PHY_INTERFACE_MODE_SMII, PHY_INTERFACE_MODE_XGMII, + PHY_INTERFACE_MODE_XLGMII, PHY_INTERFACE_MODE_MOCA, PHY_INTERFACE_MODE_QSGMII, PHY_INTERFACE_MODE_TRGMII, + PHY_INTERFACE_MODE_100BASEX, PHY_INTERFACE_MODE_1000BASEX, PHY_INTERFACE_MODE_2500BASEX, + PHY_INTERFACE_MODE_5GBASER, PHY_INTERFACE_MODE_RXAUI, PHY_INTERFACE_MODE_XAUI, /* 10GBASE-R, XFI, SFI - single lane 10G Serdes */ PHY_INTERFACE_MODE_10GBASER, + PHY_INTERFACE_MODE_25GBASER, PHY_INTERFACE_MODE_USXGMII, /* 10GBASE-KR - with Clause 73 AN */ PHY_INTERFACE_MODE_10GKR, + PHY_INTERFACE_MODE_QUSGMII, + PHY_INTERFACE_MODE_1000BASEKX, PHY_INTERFACE_MODE_MAX, } phy_interface_t; -/** - * phy_supported_speeds - return all speeds currently supported by a phy device - * @phy: The phy device to return supported speeds of. - * @speeds: buffer to store supported speeds in. - * @size: size of speeds buffer. - * - * Description: Returns the number of supported speeds, and fills - * the speeds buffer with the supported speeds. If speeds buffer is - * too small to contain all currently supported speeds, will return as - * many speeds as can fit. +/* PHY interface mode bitmap handling */ +#define DECLARE_PHY_INTERFACE_MASK(name) \ + DECLARE_BITMAP(name, PHY_INTERFACE_MODE_MAX) + +static inline void phy_interface_zero(unsigned long *intf) +{ + bitmap_zero(intf, PHY_INTERFACE_MODE_MAX); +} + +static inline bool phy_interface_empty(const unsigned long *intf) +{ + return bitmap_empty(intf, PHY_INTERFACE_MODE_MAX); +} + +static inline void phy_interface_and(unsigned long *dst, const unsigned long *a, + const unsigned long *b) +{ + bitmap_and(dst, a, b, PHY_INTERFACE_MODE_MAX); +} + +static inline void phy_interface_or(unsigned long *dst, const unsigned long *a, + const unsigned long *b) +{ + bitmap_or(dst, a, b, PHY_INTERFACE_MODE_MAX); +} + +static inline void phy_interface_set_rgmii(unsigned long *intf) +{ + __set_bit(PHY_INTERFACE_MODE_RGMII, intf); + __set_bit(PHY_INTERFACE_MODE_RGMII_ID, intf); + __set_bit(PHY_INTERFACE_MODE_RGMII_RXID, intf); + __set_bit(PHY_INTERFACE_MODE_RGMII_TXID, intf); +} + +/* + * phy_supported_speeds - return all speeds currently supported by a PHY device */ unsigned int phy_supported_speeds(struct phy_device *phy, unsigned int *speeds, @@ -128,9 +204,9 @@ unsigned int phy_supported_speeds(struct phy_device *phy, * phy_modes - map phy_interface_t enum to device tree binding of phy-mode * @interface: enum phy_interface_t value * - * Description: maps 'enum phy_interface_t' defined in this file + * Description: maps enum &phy_interface_t defined in this file * into the device tree binding of 'phy-mode', so that Ethernet - * device driver can get phy interface from device tree. + * device driver can get PHY interface from device tree. */ static inline const char *phy_modes(phy_interface_t interface) { @@ -151,6 +227,8 @@ static inline const char *phy_modes(phy_interface_t interface) return "rev-mii"; case PHY_INTERFACE_MODE_RMII: return "rmii"; + case PHY_INTERFACE_MODE_REVRMII: + return "rev-rmii"; case PHY_INTERFACE_MODE_RGMII: return "rgmii"; case PHY_INTERFACE_MODE_RGMII_ID: @@ -165,6 +243,8 @@ static inline const char *phy_modes(phy_interface_t interface) return "smii"; case PHY_INTERFACE_MODE_XGMII: return "xgmii"; + case PHY_INTERFACE_MODE_XLGMII: + return "xlgmii"; case PHY_INTERFACE_MODE_MOCA: return "moca"; case PHY_INTERFACE_MODE_QSGMII: @@ -173,24 +253,33 @@ static inline const char *phy_modes(phy_interface_t interface) return "trgmii"; case PHY_INTERFACE_MODE_1000BASEX: return "1000base-x"; + case PHY_INTERFACE_MODE_1000BASEKX: + return "1000base-kx"; case PHY_INTERFACE_MODE_2500BASEX: return "2500base-x"; + case PHY_INTERFACE_MODE_5GBASER: + return "5gbase-r"; case PHY_INTERFACE_MODE_RXAUI: return "rxaui"; case PHY_INTERFACE_MODE_XAUI: return "xaui"; case PHY_INTERFACE_MODE_10GBASER: return "10gbase-r"; + case PHY_INTERFACE_MODE_25GBASER: + return "25gbase-r"; case PHY_INTERFACE_MODE_USXGMII: return "usxgmii"; case PHY_INTERFACE_MODE_10GKR: return "10gbase-kr"; + case PHY_INTERFACE_MODE_100BASEX: + return "100base-x"; + case PHY_INTERFACE_MODE_QUSGMII: + return "qusgmii"; default: return "unknown"; } } - #define PHY_INIT_TIMEOUT 100000 #define PHY_FORCE_TIMEOUT 10 @@ -201,18 +290,20 @@ static inline const char *phy_modes(phy_interface_t interface) #define MII_BUS_ID_SIZE 61 -/* Or MII_ADDR_C45 into regnum for read/write on mii_bus to enable the 21 bit - IEEE 802.3ae clause 45 addressing mode used by 10GIGE phy chips. */ -#define MII_ADDR_C45 (1<<30) -#define MII_DEVADDR_C45_SHIFT 16 -#define MII_REGADDR_C45_MASK GENMASK(15, 0) - struct device; struct phylink; struct sfp_bus; struct sfp_upstream_ops; struct sk_buff; +/** + * struct mdio_bus_stats - Statistics counters for MDIO busses + * @transfers: Total number of transfers, i.e. @writes + @reads + * @errors: Number of MDIO transfers that returned an error + * @writes: Number of write transfers + * @reads: Number of read transfers + * @syncp: Synchronisation for incrementing statistics + */ struct mdio_bus_stats { u64_stats_t transfers; u64_stats_t errors; @@ -222,7 +313,45 @@ struct mdio_bus_stats { struct u64_stats_sync syncp; }; -/* +/** + * struct phy_package_shared - Shared information in PHY packages + * @addr: Common PHY address used to combine PHYs in one package + * @refcnt: Number of PHYs connected to this shared data + * @flags: Initialization of PHY package + * @priv_size: Size of the shared private data @priv + * @priv: Driver private data shared across a PHY package + * + * Represents a shared structure between different phydev's in the same + * package, for example a quad PHY. See phy_package_join() and + * phy_package_leave(). + */ +struct phy_package_shared { + int addr; + refcount_t refcnt; + unsigned long flags; + size_t priv_size; + + /* private data pointer */ + /* note that this pointer is shared between different phydevs and + * the user has to take care of appropriate locking. It is allocated + * and freed automatically by phy_package_join() and + * phy_package_leave(). + */ + void *priv; +}; + +/* used as bit number in atomic bitops */ +#define PHY_SHARED_F_INIT_DONE 0 +#define PHY_SHARED_F_PROBE_DONE 1 + +/** + * struct mii_bus - Represents an MDIO bus + * + * @owner: Who owns this device + * @name: User friendly name for this MDIO device, or driver name + * @id: Unique identifier for this bus, typical from bus hierarchy + * @priv: Driver private data + * * The Bus class for PHYs. Devices which provide access to * PHYs should register using this structure */ @@ -231,56 +360,93 @@ struct mii_bus { const char *name; char id[MII_BUS_ID_SIZE]; void *priv; + /** @read: Perform a read transfer on the bus */ int (*read)(struct mii_bus *bus, int addr, int regnum); + /** @write: Perform a write transfer on the bus */ int (*write)(struct mii_bus *bus, int addr, int regnum, u16 val); + /** @reset: Perform a reset of the bus */ int (*reset)(struct mii_bus *bus); + + /** @stats: Statistic counters per device on the bus */ struct mdio_bus_stats stats[PHY_MAX_ADDR]; - /* - * A lock to ensure that only one thing can read/write + /** + * @mdio_lock: A lock to ensure that only one thing can read/write * the MDIO bus at a time */ struct mutex mdio_lock; + /** @parent: Parent device of this bus */ struct device *parent; + /** @state: State of bus structure */ enum { MDIOBUS_ALLOCATED = 1, MDIOBUS_REGISTERED, MDIOBUS_UNREGISTERED, MDIOBUS_RELEASED, } state; + + /** @dev: Kernel device representation */ struct device dev; - /* list of all PHYs on bus */ + /** @mdio_map: list of all MDIO devices on bus */ struct mdio_device *mdio_map[PHY_MAX_ADDR]; - /* PHY addresses to be ignored when probing */ + /** @phy_mask: PHY addresses to be ignored when probing */ u32 phy_mask; - /* PHY addresses to ignore the TA/read failure */ + /** @phy_ignore_ta_mask: PHY addresses to ignore the TA/read failure */ u32 phy_ignore_ta_mask; - /* - * An array of interrupts, each PHY's interrupt at the index + /** + * @irq: An array of interrupts, each PHY's interrupt at the index * matching its address */ int irq[PHY_MAX_ADDR]; - /* GPIO reset pulse width in microseconds */ + /** @reset_delay_us: GPIO reset pulse width in microseconds */ int reset_delay_us; - /* RESET GPIO descriptor pointer */ + /** @reset_post_delay_us: GPIO reset deassert delay in microseconds */ + int reset_post_delay_us; + /** @reset_gpiod: Reset GPIO descriptor pointer */ struct gpio_desc *reset_gpiod; + + /** @probe_capabilities: bus capabilities, used for probing */ + enum { + MDIOBUS_NO_CAP = 0, + MDIOBUS_C22, + MDIOBUS_C45, + MDIOBUS_C22_C45, + } probe_capabilities; + + /** @shared_lock: protect access to the shared element */ + struct mutex shared_lock; + + /** @shared: shared state across different PHYs */ + struct phy_package_shared *shared[PHY_MAX_ADDR]; }; #define to_mii_bus(d) container_of(d, struct mii_bus, dev) -struct mii_bus *mdiobus_alloc_size(size_t); +struct mii_bus *mdiobus_alloc_size(size_t size); + +/** + * mdiobus_alloc - Allocate an MDIO bus structure + * + * The internal state of the MDIO bus will be set of MDIOBUS_ALLOCATED ready + * for the driver to register the bus. + */ static inline struct mii_bus *mdiobus_alloc(void) { return mdiobus_alloc_size(0); } int __mdiobus_register(struct mii_bus *bus, struct module *owner); +int __devm_mdiobus_register(struct device *dev, struct mii_bus *bus, + struct module *owner); #define mdiobus_register(bus) __mdiobus_register(bus, THIS_MODULE) +#define devm_mdiobus_register(dev, bus) \ + __devm_mdiobus_register(dev, bus, THIS_MODULE) + void mdiobus_unregister(struct mii_bus *bus); void mdiobus_free(struct mii_bus *bus); struct mii_bus *devm_mdiobus_alloc_size(struct device *dev, int sizeof_priv); @@ -289,40 +455,47 @@ static inline struct mii_bus *devm_mdiobus_alloc(struct device *dev) return devm_mdiobus_alloc_size(dev, 0); } -void devm_mdiobus_free(struct device *dev, struct mii_bus *bus); +struct mii_bus *mdio_find_bus(const char *mdio_name); struct phy_device *mdiobus_scan(struct mii_bus *bus, int addr); #define PHY_INTERRUPT_DISABLED false #define PHY_INTERRUPT_ENABLED true -/* PHY state machine states: +/** + * enum phy_state - PHY state machine states: * - * DOWN: PHY device and driver are not ready for anything. probe + * @PHY_DOWN: PHY device and driver are not ready for anything. probe * should be called if and only if the PHY is in this state, * given that the PHY device exists. - * - PHY driver probe function will set the state to READY + * - PHY driver probe function will set the state to @PHY_READY * - * READY: PHY is ready to send and receive packets, but the + * @PHY_READY: PHY is ready to send and receive packets, but the * controller is not. By default, PHYs which do not implement * probe will be set to this state by phy_probe(). * - start will set the state to UP * - * UP: The PHY and attached device are ready to do work. + * @PHY_UP: The PHY and attached device are ready to do work. * Interrupts should be started here. - * - timer moves to NOLINK or RUNNING + * - timer moves to @PHY_NOLINK or @PHY_RUNNING * - * NOLINK: PHY is up, but not currently plugged in. - * - irq or timer will set RUNNING if link comes back - * - phy_stop moves to HALTED + * @PHY_NOLINK: PHY is up, but not currently plugged in. + * - irq or timer will set @PHY_RUNNING if link comes back + * - phy_stop moves to @PHY_HALTED * - * RUNNING: PHY is currently up, running, and possibly sending + * @PHY_RUNNING: PHY is currently up, running, and possibly sending * and/or receiving packets - * - irq or timer will set NOLINK if link goes down - * - phy_stop moves to HALTED + * - irq or timer will set @PHY_NOLINK if link goes down + * - phy_stop moves to @PHY_HALTED * - * HALTED: PHY is up, but no polling or interrupts are done. Or + * @PHY_CABLETEST: PHY is performing a cable test. Packet reception/sending + * is not expected to work, carrier will be indicated as down. PHY will be + * poll once per second, or on interrupt for it current state. + * Once complete, move to UP to restart the PHY. + * - phy_stop aborts the running test and moves to @PHY_HALTED + * + * @PHY_HALTED: PHY is up, but no polling or interrupts are done. Or * PHY is in an error state. - * - phy_start moves to UP + * - phy_start moves to @PHY_UP */ enum phy_state { PHY_DOWN = 0, @@ -331,48 +504,104 @@ enum phy_state { PHY_UP, PHY_RUNNING, PHY_NOLINK, + PHY_CABLETEST, }; +#define MDIO_MMD_NUM 32 + /** * struct phy_c45_device_ids - 802.3-c45 Device Identifiers - * @devices_in_package: Bit vector of devices present. + * @devices_in_package: IEEE 802.3 devices in package register value. + * @mmds_present: bit vector of MMDs present. * @device_ids: The device identifer for each present device. */ struct phy_c45_device_ids { u32 devices_in_package; - u32 device_ids[8]; + u32 mmds_present; + u32 device_ids[MDIO_MMD_NUM]; }; struct macsec_context; struct macsec_ops; -/* phy_device: An instance of a PHY +/** + * struct phy_device - An instance of a PHY + * + * @mdio: MDIO bus this PHY is on + * @drv: Pointer to the driver for this PHY instance + * @phy_id: UID for this device found during discovery + * @c45_ids: 802.3-c45 Device Identifiers if is_c45. + * @is_c45: Set to true if this PHY uses clause 45 addressing. + * @is_internal: Set to true if this PHY is internal to a MAC. + * @is_pseudo_fixed_link: Set to true if this PHY is an Ethernet switch, etc. + * @is_gigabit_capable: Set to true if PHY supports 1000Mbps + * @has_fixups: Set to true if this PHY has fixups/quirks. + * @suspended: Set to true if this PHY has been suspended successfully. + * @suspended_by_mdio_bus: Set to true if this PHY was suspended by MDIO bus. + * @sysfs_links: Internal boolean tracking sysfs symbolic links setup/removal. + * @loopback_enabled: Set true if this PHY has been loopbacked successfully. + * @downshifted_rate: Set true if link speed has been downshifted. + * @is_on_sfp_module: Set true if PHY is located on an SFP module. + * @mac_managed_pm: Set true if MAC driver takes of suspending/resuming PHY + * @state: State of the PHY for management purposes + * @dev_flags: Device-specific flags used by the PHY driver. * - * drv: Pointer to the driver for this PHY instance - * phy_id: UID for this device found during discovery - * c45_ids: 802.3-c45 Device Identifers if is_c45. - * is_c45: Set to true if this phy uses clause 45 addressing. - * is_internal: Set to true if this phy is internal to a MAC. - * is_pseudo_fixed_link: Set to true if this phy is an Ethernet switch, etc. - * is_gigabit_capable: Set to true if PHY supports 1000Mbps - * has_fixups: Set to true if this phy has fixups/quirks. - * suspended: Set to true if this phy has been suspended successfully. - * suspended_by_mdio_bus: Set to true if this phy was suspended by MDIO bus. - * sysfs_links: Internal boolean tracking sysfs symbolic links setup/removal. - * loopback_enabled: Set true if this phy has been loopbacked successfully. - * state: state of the PHY for management purposes - * dev_flags: Device-specific flags used by the PHY driver. - * irq: IRQ number of the PHY's interrupt (-1 if none) - * phy_timer: The timer for handling the state machine - * sfp_bus_attached: flag indicating whether the SFP bus has been attached - * sfp_bus: SFP bus attached to this PHY's fiber port - * attached_dev: The attached enet driver's device instance ptr - * adjust_link: Callback for the enet controller to respond to - * changes in the link state. - * macsec_ops: MACsec offloading ops. + * - Bits [15:0] are free to use by the PHY driver to communicate + * driver specific behavior. + * - Bits [23:16] are currently reserved for future use. + * - Bits [31:24] are reserved for defining generic + * PHY driver behavior. + * @irq: IRQ number of the PHY's interrupt (-1 if none) + * @phy_timer: The timer for handling the state machine + * @phylink: Pointer to phylink instance for this PHY + * @sfp_bus_attached: Flag indicating whether the SFP bus has been attached + * @sfp_bus: SFP bus attached to this PHY's fiber port + * @attached_dev: The attached enet driver's device instance ptr + * @adjust_link: Callback for the enet controller to respond to changes: in the + * link state. + * @phy_link_change: Callback for phylink for notification of link change + * @macsec_ops: MACsec offloading ops. * - * speed, duplex, pause, supported, advertising, lp_advertising, - * and autoneg are used like in mii_if_info + * @speed: Current link speed + * @duplex: Current duplex + * @port: Current port + * @pause: Current pause + * @asym_pause: Current asymmetric pause + * @supported: Combined MAC/PHY supported linkmodes + * @advertising: Currently advertised linkmodes + * @adv_old: Saved advertised while power saving for WoL + * @lp_advertising: Current link partner advertised linkmodes + * @host_interfaces: PHY interface modes supported by host + * @eee_broken_modes: Energy efficient ethernet modes which should be prohibited + * @autoneg: Flag autoneg being used + * @rate_matching: Current rate matching mode + * @link: Current link state + * @autoneg_complete: Flag auto negotiation of the link has completed + * @mdix: Current crossover + * @mdix_ctrl: User setting of crossover + * @pma_extable: Cached value of PMA/PMD Extended Abilities Register + * @interrupts: Flag interrupts have been enabled + * @irq_suspended: Flag indicating PHY is suspended and therefore interrupt + * handling shall be postponed until PHY has resumed + * @irq_rerun: Flag indicating interrupts occurred while PHY was suspended, + * requiring a rerun of the interrupt handler after resume + * @interface: enum phy_interface_t value + * @skb: Netlink message for cable diagnostics + * @nest: Netlink nest used for cable diagnostics + * @ehdr: nNtlink header for cable diagnostics + * @phy_led_triggers: Array of LED triggers + * @phy_num_led_triggers: Number of triggers in @phy_led_triggers + * @led_link_trigger: LED trigger for link up/down + * @last_triggered: last LED trigger for link speed + * @master_slave_set: User requested master/slave configuration + * @master_slave_get: Current master/slave advertisement + * @master_slave_state: Current master/slave configuration + * @mii_ts: Pointer to time stamper callbacks + * @psec: Pointer to Power Sourcing Equipment control struct + * @lock: Mutex for serialization access to PHY + * @state_queue: Work queue for state machine + * @shared: Pointer to private data shared by phys in one package + * @priv: Pointer to driver private data * * interrupts currently only supports enabled or disabled, * but could be changed in the future to support enabling @@ -400,6 +629,9 @@ struct phy_device { unsigned suspended_by_mdio_bus:1; unsigned sysfs_links:1; unsigned loopback_enabled:1; + unsigned downshifted_rate:1; + unsigned is_on_sfp_module:1; + unsigned mac_managed_pm:1; unsigned autoneg:1; /* The most recently read link state */ @@ -408,6 +640,10 @@ struct phy_device { /* Interrupts are enabled */ unsigned interrupts:1; + unsigned irq_suspended:1; + unsigned irq_rerun:1; + + int rate_matching; enum phy_state state; @@ -421,8 +657,12 @@ struct phy_device { */ int speed; int duplex; + int port; int pause; int asym_pause; + u8 master_slave_get; + u8 master_slave_set; + u8 master_slave_state; /* Union of PHY and Attached devices' supported link modes */ /* See ethtool.h for more info */ @@ -432,6 +672,9 @@ struct phy_device { /* used with phy_speed_down */ __ETHTOOL_DECLARE_LINK_MODE_MASK(adv_old); + /* Host supported PHY interface types. Should be ignored if empty. */ + DECLARE_PHY_INTERFACE_MASK(host_interfaces); + /* Energy efficient ethernet modes which should be prohibited */ u32 eee_broken_modes; @@ -453,6 +696,15 @@ struct phy_device { /* For use by PHYs to maintain extra state */ void *priv; + /* shared data pointer */ + /* For use by PHYs inside the same package that need a shared state. */ + struct phy_package_shared *shared; + + /* Reporting cable test results */ + struct sk_buff *skb; + void *ehdr; + struct nlattr *nest; + /* Interrupt and Polling infrastructure */ struct delayed_work state_queue; @@ -464,11 +716,14 @@ struct phy_device { struct phylink *phylink; struct net_device *attached_dev; struct mii_timestamper *mii_ts; + struct pse_control *psec; u8 mdix; u8 mdix_ctrl; - void (*phy_link_change)(struct phy_device *, bool up, bool do_carrier); + int pma_extable; + + void (*phy_link_change)(struct phy_device *phydev, bool up); void (*adjust_link)(struct net_device *dev); #if IS_ENABLED(CONFIG_MACSEC) @@ -476,21 +731,47 @@ struct phy_device { const struct macsec_ops *macsec_ops; #endif }; -#define to_phy_device(d) container_of(to_mdio_device(d), \ - struct phy_device, mdio) -/* struct phy_driver: Driver structure for a particular PHY type +static inline struct phy_device *to_phy_device(const struct device *dev) +{ + return container_of(to_mdio_device(dev), struct phy_device, mdio); +} + +/** + * struct phy_tdr_config - Configuration of a TDR raw test * - * driver_data: static driver data - * phy_id: The result of reading the UID registers of this PHY + * @first: Distance for first data collection point + * @last: Distance for last data collection point + * @step: Step between data collection points + * @pair: Bitmap of cable pairs to collect data for + * + * A structure containing possible configuration parameters + * for a TDR cable test. The driver does not need to implement + * all the parameters, but should report what is actually used. + * All distances are in centimeters. + */ +struct phy_tdr_config { + u32 first; + u32 last; + u32 step; + s8 pair; +}; +#define PHY_PAIR_ALL -1 + +/** + * struct phy_driver - Driver structure for a particular PHY type + * + * @mdiodrv: Data common to all MDIO devices + * @phy_id: The result of reading the UID registers of this PHY * type, and ANDing them with the phy_id_mask. This driver * only works for PHYs with IDs which match this field - * name: The friendly name of this PHY type - * phy_id_mask: Defines the important bits of the phy_id - * features: A mandatory list of features (speed, duplex, etc) + * @name: The friendly name of this PHY type + * @phy_id_mask: Defines the important bits of the phy_id + * @features: A mandatory list of features (speed, duplex, etc) * supported by this PHY - * flags: A bitfield defining certain other features this PHY + * @flags: A bitfield defining certain other features this PHY * supports (like interrupts) + * @driver_data: Static driver data * * All functions are optional. If config_aneg or read_status * are not implemented, the phy core uses the genphy versions. @@ -509,138 +790,188 @@ struct phy_driver { u32 flags; const void *driver_data; - /* - * Called to issue a PHY software reset + /** + * @soft_reset: Called to issue a PHY software reset */ int (*soft_reset)(struct phy_device *phydev); - /* - * Called to initialize the PHY, + /** + * @config_init: Called to initialize the PHY, * including after a reset */ int (*config_init)(struct phy_device *phydev); - /* - * Called during discovery. Used to set + /** + * @probe: Called during discovery. Used to set * up device-specific structures, if any */ int (*probe)(struct phy_device *phydev); - /* - * Probe the hardware to determine what abilities it has. - * Should only set phydev->supported. + /** + * @get_features: Probe the hardware to determine what + * abilities it has. Should only set phydev->supported. */ int (*get_features)(struct phy_device *phydev); + /** + * @get_rate_matching: Get the supported type of rate matching for a + * particular phy interface. This is used by phy consumers to determine + * whether to advertise lower-speed modes for that interface. It is + * assumed that if a rate matching mode is supported on an interface, + * then that interface's rate can be adapted to all slower link speeds + * supported by the phy. If iface is %PHY_INTERFACE_MODE_NA, and the phy + * supports any kind of rate matching for any interface, then it must + * return that rate matching mode (preferring %RATE_MATCH_PAUSE to + * %RATE_MATCH_CRS). If the interface is not supported, this should + * return %RATE_MATCH_NONE. + */ + int (*get_rate_matching)(struct phy_device *phydev, + phy_interface_t iface); + /* PHY Power Management */ + /** @suspend: Suspend the hardware, saving state if needed */ int (*suspend)(struct phy_device *phydev); + /** @resume: Resume the hardware, restoring state if needed */ int (*resume)(struct phy_device *phydev); - /* - * Configures the advertisement and resets + /** + * @config_aneg: Configures the advertisement and resets * autonegotiation if phydev->autoneg is on, * forces the speed to the current settings in phydev * if phydev->autoneg is off */ int (*config_aneg)(struct phy_device *phydev); - /* Determines the auto negotiation result */ + /** @aneg_done: Determines the auto negotiation result */ int (*aneg_done)(struct phy_device *phydev); - /* Determines the negotiated speed and duplex */ + /** @read_status: Determines the negotiated speed and duplex */ int (*read_status)(struct phy_device *phydev); - /* Clears any pending interrupts */ - int (*ack_interrupt)(struct phy_device *phydev); - - /* Enables or disables interrupts */ - int (*config_intr)(struct phy_device *phydev); - - /* - * Checks if the PHY generated an interrupt. - * For multi-PHY devices with shared PHY interrupt pin - * Set interrupt bits have to be cleared. + /** + * @config_intr: Enables or disables interrupts. + * It should also clear any pending interrupts prior to enabling the + * IRQs and after disabling them. */ - int (*did_interrupt)(struct phy_device *phydev); + int (*config_intr)(struct phy_device *phydev); - /* Override default interrupt handling */ - int (*handle_interrupt)(struct phy_device *phydev); + /** @handle_interrupt: Override default interrupt handling */ + irqreturn_t (*handle_interrupt)(struct phy_device *phydev); - /* Clears up any memory if needed */ + /** @remove: Clears up any memory if needed */ void (*remove)(struct phy_device *phydev); - /* Returns true if this is a suitable driver for the given - * phydev. If NULL, matching is based on phy_id and - * phy_id_mask. + /** + * @match_phy_device: Returns true if this is a suitable + * driver for the given phydev. If NULL, matching is based on + * phy_id and phy_id_mask. */ int (*match_phy_device)(struct phy_device *phydev); - /* Some devices (e.g. qnap TS-119P II) require PHY register changes to - * enable Wake on LAN, so set_wol is provided to be called in the - * ethernet driver's set_wol function. */ + /** + * @set_wol: Some devices (e.g. qnap TS-119P II) require PHY + * register changes to enable Wake on LAN, so set_wol is + * provided to be called in the ethernet driver's set_wol + * function. + */ int (*set_wol)(struct phy_device *dev, struct ethtool_wolinfo *wol); - /* See set_wol, but for checking whether Wake on LAN is enabled. */ + /** + * @get_wol: See set_wol, but for checking whether Wake on LAN + * is enabled. + */ void (*get_wol)(struct phy_device *dev, struct ethtool_wolinfo *wol); - /* - * Called to inform a PHY device driver when the core is about to - * change the link state. This callback is supposed to be used as - * fixup hook for drivers that need to take action when the link - * state changes. Drivers are by no means allowed to mess with the + /** + * @link_change_notify: Called to inform a PHY device driver + * when the core is about to change the link state. This + * callback is supposed to be used as fixup hook for drivers + * that need to take action when the link state + * changes. Drivers are by no means allowed to mess with the * PHY device structure in their implementations. */ void (*link_change_notify)(struct phy_device *dev); - /* - * Phy specific driver override for reading a MMD register. - * This function is optional for PHY specific drivers. When - * not provided, the default MMD read function will be used - * by phy_read_mmd(), which will use either a direct read for - * Clause 45 PHYs or an indirect read for Clause 22 PHYs. - * devnum is the MMD device number within the PHY device, - * regnum is the register within the selected MMD device. + /** + * @read_mmd: PHY specific driver override for reading a MMD + * register. This function is optional for PHY specific + * drivers. When not provided, the default MMD read function + * will be used by phy_read_mmd(), which will use either a + * direct read for Clause 45 PHYs or an indirect read for + * Clause 22 PHYs. devnum is the MMD device number within the + * PHY device, regnum is the register within the selected MMD + * device. */ int (*read_mmd)(struct phy_device *dev, int devnum, u16 regnum); - /* - * Phy specific driver override for writing a MMD register. - * This function is optional for PHY specific drivers. When - * not provided, the default MMD write function will be used - * by phy_write_mmd(), which will use either a direct write for - * Clause 45 PHYs, or an indirect write for Clause 22 PHYs. - * devnum is the MMD device number within the PHY device, - * regnum is the register within the selected MMD device. - * val is the value to be written. + /** + * @write_mmd: PHY specific driver override for writing a MMD + * register. This function is optional for PHY specific + * drivers. When not provided, the default MMD write function + * will be used by phy_write_mmd(), which will use either a + * direct write for Clause 45 PHYs, or an indirect write for + * Clause 22 PHYs. devnum is the MMD device number within the + * PHY device, regnum is the register within the selected MMD + * device. val is the value to be written. */ int (*write_mmd)(struct phy_device *dev, int devnum, u16 regnum, u16 val); + /** @read_page: Return the current PHY register page number */ int (*read_page)(struct phy_device *dev); + /** @write_page: Set the current PHY register page number */ int (*write_page)(struct phy_device *dev, int page); - /* Get the size and type of the eeprom contained within a plug-in - * module */ + /** + * @module_info: Get the size and type of the eeprom contained + * within a plug-in module + */ int (*module_info)(struct phy_device *dev, struct ethtool_modinfo *modinfo); - /* Get the eeprom information from the plug-in module */ + /** + * @module_eeprom: Get the eeprom information from the plug-in + * module + */ int (*module_eeprom)(struct phy_device *dev, struct ethtool_eeprom *ee, u8 *data); - /* Get statistics from the phy using ethtool */ + /** @cable_test_start: Start a cable test */ + int (*cable_test_start)(struct phy_device *dev); + + /** @cable_test_tdr_start: Start a raw TDR cable test */ + int (*cable_test_tdr_start)(struct phy_device *dev, + const struct phy_tdr_config *config); + + /** + * @cable_test_get_status: Once per second, or on interrupt, + * request the status of the test. + */ + int (*cable_test_get_status)(struct phy_device *dev, bool *finished); + + /* Get statistics from the PHY using ethtool */ + /** @get_sset_count: Number of statistic counters */ int (*get_sset_count)(struct phy_device *dev); + /** @get_strings: Names of the statistic counters */ void (*get_strings)(struct phy_device *dev, u8 *data); + /** @get_stats: Return the statistic counter values */ void (*get_stats)(struct phy_device *dev, struct ethtool_stats *stats, u64 *data); /* Get and Set PHY tunables */ + /** @get_tunable: Return the value of a tunable */ int (*get_tunable)(struct phy_device *dev, struct ethtool_tunable *tuna, void *data); + /** @set_tunable: Set the value of a tunable */ int (*set_tunable)(struct phy_device *dev, struct ethtool_tunable *tuna, const void *data); + /** @set_loopback: Set the loopback mood of the PHY */ int (*set_loopback)(struct phy_device *dev, bool enable); + /** @get_sqi: Get the signal quality indication */ + int (*get_sqi)(struct phy_device *dev); + /** @get_sqi_max: Get the maximum signal quality indication */ + int (*get_sqi_max)(struct phy_device *dev); }; #define to_phy_driver(d) container_of(to_mdio_common_driver(d), \ struct phy_driver, mdiodrv) @@ -663,6 +994,9 @@ struct phy_fixup { const char *phy_speed_to_str(int speed); const char *phy_duplex_to_str(unsigned int duplex); +const char *phy_rate_matching_to_str(int rate_matching); + +int phy_interface_num_ports(phy_interface_t interface); /* A structure for mapping a particular speed and duplex * combination to a particular SUPPORTED and ADVERTISED value @@ -693,6 +1027,7 @@ static inline bool phy_is_started(struct phy_device *phydev) void phy_resolve_aneg_pause(struct phy_device *phydev); void phy_resolve_aneg_linkmode(struct phy_device *phydev); +void phy_check_downshift(struct phy_device *phydev); /** * phy_read - Convenience function for reading a given PHY register @@ -708,6 +1043,19 @@ static inline int phy_read(struct phy_device *phydev, u32 regnum) return mdiobus_read(phydev->mdio.bus, phydev->mdio.addr, regnum); } +#define phy_read_poll_timeout(phydev, regnum, val, cond, sleep_us, \ + timeout_us, sleep_before_read) \ +({ \ + int __ret = read_poll_timeout(phy_read, val, (cond) || val < 0, \ + sleep_us, timeout_us, sleep_before_read, phydev, regnum); \ + if (val < 0) \ + __ret = val; \ + if (__ret) \ + phydev_err(phydev, "%s failed: %d\n", __func__, __ret); \ + __ret; \ +}) + + /** * __phy_read - convenience function for reading a given PHY register * @phydev: the phy_device struct @@ -750,48 +1098,76 @@ static inline int __phy_write(struct phy_device *phydev, u32 regnum, u16 val) } /** + * __phy_modify_changed() - Convenience function for modifying a PHY register + * @phydev: a pointer to a &struct phy_device + * @regnum: register number + * @mask: bit mask of bits to clear + * @set: bit mask of bits to set + * + * Unlocked helper function which allows a PHY register to be modified as + * new register value = (old register value & ~mask) | set + * + * Returns negative errno, 0 if there was no change, and 1 in case of change + */ +static inline int __phy_modify_changed(struct phy_device *phydev, u32 regnum, + u16 mask, u16 set) +{ + return __mdiobus_modify_changed(phydev->mdio.bus, phydev->mdio.addr, + regnum, mask, set); +} + +/* * phy_read_mmd - Convenience function for reading a register * from an MMD on a given PHY. - * @phydev: The phy_device struct - * @devad: The MMD to read from - * @regnum: The register on the MMD to read - * - * Same rules as for phy_read(); */ int phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum); /** - * __phy_read_mmd - Convenience function for reading a register - * from an MMD on a given PHY. + * phy_read_mmd_poll_timeout - Periodically poll a PHY register until a + * condition is met or a timeout occurs + * * @phydev: The phy_device struct - * @devad: The MMD to read from + * @devaddr: The MMD to read from * @regnum: The register on the MMD to read - * - * Same rules as for __phy_read(); + * @val: Variable to read the register into + * @cond: Break condition (usually involving @val) + * @sleep_us: Maximum time to sleep between reads in us (0 + * tight-loops). Should be less than ~20ms since usleep_range + * is used (see Documentation/timers/timers-howto.rst). + * @timeout_us: Timeout in us, 0 means never timeout + * @sleep_before_read: if it is true, sleep @sleep_us before read. + * Returns 0 on success and -ETIMEDOUT upon a timeout. In either + * case, the last read value at @args is stored in @val. Must not + * be called from atomic context if sleep_us or timeout_us are used. + */ +#define phy_read_mmd_poll_timeout(phydev, devaddr, regnum, val, cond, \ + sleep_us, timeout_us, sleep_before_read) \ +({ \ + int __ret = read_poll_timeout(phy_read_mmd, val, (cond) || val < 0, \ + sleep_us, timeout_us, sleep_before_read, \ + phydev, devaddr, regnum); \ + if (val < 0) \ + __ret = val; \ + if (__ret) \ + phydev_err(phydev, "%s failed: %d\n", __func__, __ret); \ + __ret; \ +}) + +/* + * __phy_read_mmd - Convenience function for reading a register + * from an MMD on a given PHY. */ int __phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum); -/** +/* * phy_write_mmd - Convenience function for writing a register * on an MMD on a given PHY. - * @phydev: The phy_device struct - * @devad: The MMD to write to - * @regnum: The register on the MMD to read - * @val: value to write to @regnum - * - * Same rules as for phy_write(); */ int phy_write_mmd(struct phy_device *phydev, int devad, u32 regnum, u16 val); -/** +/* * __phy_write_mmd - Convenience function for writing a register * on an MMD on a given PHY. - * @phydev: The phy_device struct - * @devad: The MMD to write to - * @regnum: The register on the MMD to read - * @val: value to write to @regnum - * - * Same rules as for __phy_write(); */ int __phy_write_mmd(struct phy_device *phydev, int devad, u32 regnum, u16 val); @@ -925,11 +1301,11 @@ static inline int phy_clear_bits_mmd(struct phy_device *phydev, int devad, * @phydev: the phy_device struct * * NOTE: must be kept in sync with addition/removal of PHY_POLL and - * PHY_IGNORE_INTERRUPT + * PHY_MAC_INTERRUPT */ static inline bool phy_interrupt_is_valid(struct phy_device *phydev) { - return phydev->irq != PHY_POLL && phydev->irq != PHY_IGNORE_INTERRUPT; + return phydev->irq != PHY_POLL && phydev->irq != PHY_MAC_INTERRUPT; } /** @@ -939,6 +1315,10 @@ static inline bool phy_interrupt_is_valid(struct phy_device *phydev) */ static inline bool phy_polling_mode(struct phy_device *phydev) { + if (phydev->state == PHY_CABLETEST) + if (phydev->drv->flags & PHY_POLL_CABLE_TEST) + return true; + return phydev->irq == PHY_POLL; } @@ -1012,9 +1392,18 @@ static inline bool phy_is_internal(struct phy_device *phydev) } /** + * phy_on_sfp - Convenience function for testing if a PHY is on an SFP module + * @phydev: the phy_device struct + */ +static inline bool phy_on_sfp(struct phy_device *phydev) +{ + return phydev->is_on_sfp_module; +} + +/** * phy_interface_mode_is_rgmii - Convenience function for testing if a * PHY interface mode is RGMII (all variants) - * @mode: the phy_interface_t enum + * @mode: the &phy_interface_t enum */ static inline bool phy_interface_mode_is_rgmii(phy_interface_t mode) { @@ -1023,11 +1412,11 @@ static inline bool phy_interface_mode_is_rgmii(phy_interface_t mode) }; /** - * phy_interface_mode_is_8023z() - does the phy interface mode use 802.3z + * phy_interface_mode_is_8023z() - does the PHY interface mode use 802.3z * negotiation * @mode: one of &enum phy_interface_t * - * Returns true if the phy interface mode uses the 16-bit negotiation + * Returns true if the PHY interface mode uses the 16-bit negotiation * word as defined in 802.3z. (See 802.3-2015 37.2.1 Config_Reg encoding) */ static inline bool phy_interface_mode_is_8023z(phy_interface_t mode) @@ -1046,7 +1435,7 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev) return phy_interface_mode_is_rgmii(phydev->interface); }; -/* +/** * phy_is_pseudo_fixed_link - Convenience function for testing if this * PHY is the CPU port facing side of an Ethernet switch, or similar. * @phydev: the phy_device struct @@ -1070,10 +1459,42 @@ struct phy_device *phy_device_create(struct mii_bus *bus, int addr, u32 phy_id, bool is_c45, struct phy_c45_device_ids *c45_ids); #if IS_ENABLED(CONFIG_PHYLIB) +int fwnode_get_phy_id(struct fwnode_handle *fwnode, u32 *phy_id); +struct mdio_device *fwnode_mdio_find_device(struct fwnode_handle *fwnode); +struct phy_device *fwnode_phy_find_device(struct fwnode_handle *phy_fwnode); +struct phy_device *device_phy_find_device(struct device *dev); +struct fwnode_handle *fwnode_get_phy_node(struct fwnode_handle *fwnode); struct phy_device *get_phy_device(struct mii_bus *bus, int addr, bool is_c45); int phy_device_register(struct phy_device *phy); void phy_device_free(struct phy_device *phydev); #else +static inline int fwnode_get_phy_id(struct fwnode_handle *fwnode, u32 *phy_id) +{ + return 0; +} +static inline +struct mdio_device *fwnode_mdio_find_device(struct fwnode_handle *fwnode) +{ + return 0; +} + +static inline +struct phy_device *fwnode_phy_find_device(struct fwnode_handle *phy_fwnode) +{ + return NULL; +} + +static inline struct phy_device *device_phy_find_device(struct device *dev) +{ + return NULL; +} + +static inline +struct fwnode_handle *fwnode_get_phy_node(struct fwnode_handle *fwnode) +{ + return NULL; +} + static inline struct phy_device *get_phy_device(struct mii_bus *bus, int addr, bool is_c45) { @@ -1088,6 +1509,7 @@ static inline int phy_device_register(struct phy_device *phy) static inline void phy_device_free(struct phy_device *phydev) { } #endif /* CONFIG_PHYLIB */ void phy_device_remove(struct phy_device *phydev); +int phy_get_c45_ids(struct phy_device *phydev); int phy_init_hw(struct phy_device *phydev); int phy_suspend(struct phy_device *phydev); int phy_resume(struct phy_device *phydev); @@ -1112,6 +1534,7 @@ void phy_disconnect(struct phy_device *phydev); void phy_detach(struct phy_device *phydev); void phy_start(struct phy_device *phydev); void phy_stop(struct phy_device *phydev); +int phy_config_aneg(struct phy_device *phydev); int phy_start_aneg(struct phy_device *phydev); int phy_aneg_done(struct phy_device *phydev); int phy_speed_down(struct phy_device *phydev, bool sync); @@ -1120,6 +1543,34 @@ int phy_speed_up(struct phy_device *phydev); int phy_restart_aneg(struct phy_device *phydev); int phy_reset_after_clk_enable(struct phy_device *phydev); +#if IS_ENABLED(CONFIG_PHYLIB) +int phy_start_cable_test(struct phy_device *phydev, + struct netlink_ext_ack *extack); +int phy_start_cable_test_tdr(struct phy_device *phydev, + struct netlink_ext_ack *extack, + const struct phy_tdr_config *config); +#else +static inline +int phy_start_cable_test(struct phy_device *phydev, + struct netlink_ext_ack *extack) +{ + NL_SET_ERR_MSG(extack, "Kernel not compiled with PHYLIB support"); + return -EOPNOTSUPP; +} +static inline +int phy_start_cable_test_tdr(struct phy_device *phydev, + struct netlink_ext_ack *extack, + const struct phy_tdr_config *config) +{ + NL_SET_ERR_MSG(extack, "Kernel not compiled with PHYLIB support"); + return -EOPNOTSUPP; +} +#endif + +int phy_cable_test_result(struct phy_device *phydev, u8 pair, u16 result); +int phy_cable_test_fault_length(struct phy_device *phydev, u8 pair, + u16 cm); + static inline void phy_device_reset(struct phy_device *phydev, int value) { mdio_device_reset(&phydev->mdio, value); @@ -1128,6 +1579,9 @@ static inline void phy_device_reset(struct phy_device *phydev, int value) #define phydev_err(_phydev, format, args...) \ dev_err(&_phydev->mdio.dev, format, ##args) +#define phydev_err_probe(_phydev, err, format, args...) \ + dev_err_probe(&_phydev->mdio.dev, err, format, ##args) + #define phydev_info(_phydev, format, args...) \ dev_info(&_phydev->mdio.dev, format, ##args) @@ -1170,24 +1624,18 @@ int genphy_update_link(struct phy_device *phydev); int genphy_read_lpa(struct phy_device *phydev); int genphy_read_status_fixed(struct phy_device *phydev); int genphy_read_status(struct phy_device *phydev); +int genphy_read_master_slave(struct phy_device *phydev); int genphy_suspend(struct phy_device *phydev); int genphy_resume(struct phy_device *phydev); int genphy_loopback(struct phy_device *phydev, bool enable); int genphy_soft_reset(struct phy_device *phydev); +irqreturn_t genphy_handle_interrupt_no_ack(struct phy_device *phydev); static inline int genphy_config_aneg(struct phy_device *phydev) { return __genphy_config_aneg(phydev, false); } -static inline int genphy_no_soft_reset(struct phy_device *phydev) -{ - return 0; -} -static inline int genphy_no_ack_interrupt(struct phy_device *phydev) -{ - return 0; -} static inline int genphy_no_config_intr(struct phy_device *phydev) { return 0; @@ -1209,12 +1657,22 @@ int genphy_c45_read_link(struct phy_device *phydev); int genphy_c45_read_lpa(struct phy_device *phydev); int genphy_c45_read_pma(struct phy_device *phydev); int genphy_c45_pma_setup_forced(struct phy_device *phydev); +int genphy_c45_pma_baset1_setup_master_slave(struct phy_device *phydev); int genphy_c45_an_config_aneg(struct phy_device *phydev); int genphy_c45_an_disable_aneg(struct phy_device *phydev); int genphy_c45_read_mdix(struct phy_device *phydev); int genphy_c45_pma_read_abilities(struct phy_device *phydev); +int genphy_c45_pma_baset1_read_master_slave(struct phy_device *phydev); int genphy_c45_read_status(struct phy_device *phydev); +int genphy_c45_baset1_read_status(struct phy_device *phydev); int genphy_c45_config_aneg(struct phy_device *phydev); +int genphy_c45_loopback(struct phy_device *phydev, bool enable); +int genphy_c45_pma_resume(struct phy_device *phydev); +int genphy_c45_pma_suspend(struct phy_device *phydev); +int genphy_c45_fast_retrain(struct phy_device *phydev, bool enable); + +/* Generic C45 PHY driver */ +extern struct phy_driver genphy_c45_driver; /* The gen10g_* functions are the old Clause 45 stub */ int gen10g_config_aneg(struct phy_device *phydev); @@ -1235,8 +1693,10 @@ void phy_drivers_unregister(struct phy_driver *drv, int n); int phy_driver_register(struct phy_driver *new_driver, struct module *owner); int phy_drivers_register(struct phy_driver *new_driver, int n, struct module *owner); +void phy_error(struct phy_device *phydev); void phy_state_machine(struct work_struct *work); void phy_queue_state_machine(struct phy_device *phydev, unsigned long jiffies); +void phy_trigger_machine(struct phy_device *phydev); void phy_mac_interrupt(struct phy_device *phydev); void phy_start_machine(struct phy_device *phydev); void phy_stop_machine(struct phy_device *phydev); @@ -1247,10 +1707,13 @@ int phy_ethtool_ksettings_set(struct phy_device *phydev, int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd); int phy_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd); int phy_do_ioctl_running(struct net_device *dev, struct ifreq *ifr, int cmd); +int phy_disable_interrupts(struct phy_device *phydev); void phy_request_interrupt(struct phy_device *phydev); void phy_free_interrupt(struct phy_device *phydev); void phy_print_status(struct phy_device *phydev); -int phy_set_max_speed(struct phy_device *phydev, u32 max_speed); +int phy_get_rate_matching(struct phy_device *phydev, + phy_interface_t iface); +void phy_set_max_speed(struct phy_device *phydev, u32 max_speed); void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode); void phy_advertise_supported(struct phy_device *phydev); void phy_support_sym_pause(struct phy_device *phydev); @@ -1260,6 +1723,13 @@ void phy_set_sym_pause(struct phy_device *phydev, bool rx, bool tx, void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx); bool phy_validate_pause(struct phy_device *phydev, struct ethtool_pauseparam *pp); +void phy_get_pause(struct phy_device *phydev, bool *tx_pause, bool *rx_pause); + +s32 phy_get_internal_delay(struct phy_device *phydev, struct device *dev, + const int *delay_values, int size, bool is_rx); + +void phy_resolve_pause(unsigned long *local_adv, unsigned long *partner_adv, + bool *tx_pause, bool *rx_pause); int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask, int (*run)(struct phy_device *)); @@ -1284,56 +1754,82 @@ int phy_ethtool_get_link_ksettings(struct net_device *ndev, int phy_ethtool_set_link_ksettings(struct net_device *ndev, const struct ethtool_link_ksettings *cmd); int phy_ethtool_nway_reset(struct net_device *ndev); +int phy_package_join(struct phy_device *phydev, int addr, size_t priv_size); +void phy_package_leave(struct phy_device *phydev); +int devm_phy_package_join(struct device *dev, struct phy_device *phydev, + int addr, size_t priv_size); #if IS_ENABLED(CONFIG_PHYLIB) int __init mdio_bus_init(void); void mdio_bus_exit(void); #endif -/* Inline function for use within net/core/ethtool.c (built-in) */ -static inline int phy_ethtool_get_strings(struct phy_device *phydev, u8 *data) +int phy_ethtool_get_strings(struct phy_device *phydev, u8 *data); +int phy_ethtool_get_sset_count(struct phy_device *phydev); +int phy_ethtool_get_stats(struct phy_device *phydev, + struct ethtool_stats *stats, u64 *data); + +static inline int phy_package_read(struct phy_device *phydev, u32 regnum) { - if (!phydev->drv) - return -EIO; + struct phy_package_shared *shared = phydev->shared; - mutex_lock(&phydev->lock); - phydev->drv->get_strings(phydev, data); - mutex_unlock(&phydev->lock); + if (!shared) + return -EIO; - return 0; + return mdiobus_read(phydev->mdio.bus, shared->addr, regnum); } -static inline int phy_ethtool_get_sset_count(struct phy_device *phydev) +static inline int __phy_package_read(struct phy_device *phydev, u32 regnum) { - int ret; + struct phy_package_shared *shared = phydev->shared; - if (!phydev->drv) + if (!shared) return -EIO; - if (phydev->drv->get_sset_count && - phydev->drv->get_strings && - phydev->drv->get_stats) { - mutex_lock(&phydev->lock); - ret = phydev->drv->get_sset_count(phydev); - mutex_unlock(&phydev->lock); + return __mdiobus_read(phydev->mdio.bus, shared->addr, regnum); +} - return ret; - } +static inline int phy_package_write(struct phy_device *phydev, + u32 regnum, u16 val) +{ + struct phy_package_shared *shared = phydev->shared; - return -EOPNOTSUPP; + if (!shared) + return -EIO; + + return mdiobus_write(phydev->mdio.bus, shared->addr, regnum, val); } -static inline int phy_ethtool_get_stats(struct phy_device *phydev, - struct ethtool_stats *stats, u64 *data) +static inline int __phy_package_write(struct phy_device *phydev, + u32 regnum, u16 val) { - if (!phydev->drv) + struct phy_package_shared *shared = phydev->shared; + + if (!shared) return -EIO; - mutex_lock(&phydev->lock); - phydev->drv->get_stats(phydev, stats, data); - mutex_unlock(&phydev->lock); + return __mdiobus_write(phydev->mdio.bus, shared->addr, regnum, val); +} - return 0; +static inline bool __phy_package_set_once(struct phy_device *phydev, + unsigned int b) +{ + struct phy_package_shared *shared = phydev->shared; + + if (!shared) + return false; + + return !test_and_set_bit(b, &shared->flags); +} + +static inline bool phy_package_init_once(struct phy_device *phydev) +{ + return __phy_package_set_once(phydev, PHY_SHARED_F_INIT_DONE); +} + +static inline bool phy_package_probe_once(struct phy_device *phydev) +{ + return __phy_package_set_once(phydev, PHY_SHARED_F_PROBE_DONE); } extern struct bus_type mdio_bus_type; @@ -1358,8 +1854,9 @@ static inline int mdiobus_register_board_info(const struct mdio_board_info *i, /** - * module_phy_driver() - Helper macro for registering PHY drivers + * phy_module_driver() - Helper macro for registering PHY drivers * @__phy_drivers: array of PHY drivers to register + * @__count: Numbers of members in array * * Helper macro for PHY drivers which do not do anything special in module * init/exit. Each module may only use this macro once, and calling it |