diff options
Diffstat (limited to 'include/linux/spi/spi_bitbang.h')
| -rw-r--r-- | include/linux/spi/spi_bitbang.h | 135 |
1 files changed, 135 insertions, 0 deletions
diff --git a/include/linux/spi/spi_bitbang.h b/include/linux/spi/spi_bitbang.h new file mode 100644 index 000000000000..c961fe9bf3eb --- /dev/null +++ b/include/linux/spi/spi_bitbang.h @@ -0,0 +1,135 @@ +#ifndef __SPI_BITBANG_H +#define __SPI_BITBANG_H + +/* + * Mix this utility code with some glue code to get one of several types of + * simple SPI master driver. Two do polled word-at-a-time I/O: + * + * - GPIO/parport bitbangers. Provide chipselect() and txrx_word[](), + * expanding the per-word routines from the inline templates below. + * + * - Drivers for controllers resembling bare shift registers. Provide + * chipselect() and txrx_word[](), with custom setup()/cleanup() methods + * that use your controller's clock and chipselect registers. + * + * Some hardware works well with requests at spi_transfer scope: + * + * - Drivers leveraging smarter hardware, with fifos or DMA; or for half + * duplex (MicroWire) controllers. Provide chipslect() and txrx_bufs(), + * and custom setup()/cleanup() methods. + */ +struct spi_bitbang { + struct workqueue_struct *workqueue; + struct work_struct work; + + spinlock_t lock; + struct list_head queue; + u8 busy; + u8 shutdown; + u8 use_dma; + + struct spi_master *master; + + void (*chipselect)(struct spi_device *spi, int is_on); +#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */ +#define BITBANG_CS_INACTIVE 0 + + /* txrx_bufs() may handle dma mapping for transfers that don't + * already have one (transfer.{tx,rx}_dma is zero), or use PIO + */ + int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t); + + /* txrx_word[SPI_MODE_*]() just looks like a shift register */ + u32 (*txrx_word[4])(struct spi_device *spi, + unsigned nsecs, + u32 word, u8 bits); +}; + +/* you can call these default bitbang->master methods from your custom + * methods, if you like. + */ +extern int spi_bitbang_setup(struct spi_device *spi); +extern void spi_bitbang_cleanup(const struct spi_device *spi); +extern int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m); + +/* start or stop queue processing */ +extern int spi_bitbang_start(struct spi_bitbang *spi); +extern int spi_bitbang_stop(struct spi_bitbang *spi); + +#endif /* __SPI_BITBANG_H */ + +/*-------------------------------------------------------------------------*/ + +#ifdef EXPAND_BITBANG_TXRX + +/* + * The code that knows what GPIO pins do what should have declared four + * functions, ideally as inlines, before #defining EXPAND_BITBANG_TXRX + * and including this header: + * + * void setsck(struct spi_device *, int is_on); + * void setmosi(struct spi_device *, int is_on); + * int getmiso(struct spi_device *); + * void spidelay(unsigned); + * + * A non-inlined routine would call bitbang_txrx_*() routines. The + * main loop could easily compile down to a handful of instructions, + * especially if the delay is a NOP (to run at peak speed). + * + * Since this is software, the timings may not be exactly what your board's + * chips need ... there may be several reasons you'd need to tweak timings + * in these routines, not just make to make it faster or slower to match a + * particular CPU clock rate. + */ + +static inline u32 +bitbang_txrx_be_cpha0(struct spi_device *spi, + unsigned nsecs, unsigned cpol, + u32 word, u8 bits) +{ + /* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */ + + /* clock starts at inactive polarity */ + for (word <<= (32 - bits); likely(bits); bits--) { + + /* setup MSB (to slave) on trailing edge */ + setmosi(spi, word & (1 << 31)); + spidelay(nsecs); /* T(setup) */ + + setsck(spi, !cpol); + spidelay(nsecs); + + /* sample MSB (from slave) on leading edge */ + word <<= 1; + word |= getmiso(spi); + setsck(spi, cpol); + } + return word; +} + +static inline u32 +bitbang_txrx_be_cpha1(struct spi_device *spi, + unsigned nsecs, unsigned cpol, + u32 word, u8 bits) +{ + /* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */ + + /* clock starts at inactive polarity */ + for (word <<= (32 - bits); likely(bits); bits--) { + + /* setup MSB (to slave) on leading edge */ + setsck(spi, !cpol); + setmosi(spi, word & (1 << 31)); + spidelay(nsecs); /* T(setup) */ + + setsck(spi, cpol); + spidelay(nsecs); + + /* sample MSB (from slave) on trailing edge */ + word <<= 1; + word |= getmiso(spi); + } + return word; +} + +#endif /* EXPAND_BITBANG_TXRX */ |