diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/phy.h | 22 | ||||
| -rw-r--r-- | include/linux/phylink.h | 40 |
2 files changed, 59 insertions, 3 deletions
diff --git a/include/linux/phy.h b/include/linux/phy.h index 337230c135f7..9c66f357f489 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -280,7 +280,6 @@ static inline const char *phy_modes(phy_interface_t interface) } } - #define PHY_INIT_TIMEOUT 100000 #define PHY_FORCE_TIMEOUT 10 @@ -574,6 +573,7 @@ struct macsec_ops; * @lp_advertising: Current link partner advertised linkmodes * @eee_broken_modes: Energy efficient ethernet modes which should be prohibited * @autoneg: Flag autoneg being used + * @rate_matching: Current rate matching mode * @link: Current link state * @autoneg_complete: Flag auto negotiation of the link has completed * @mdix: Current crossover @@ -641,6 +641,8 @@ struct phy_device { unsigned irq_suspended:1; unsigned irq_rerun:1; + int rate_matching; + enum phy_state state; u32 dev_flags; @@ -805,6 +807,21 @@ struct phy_driver { */ int (*get_features)(struct phy_device *phydev); + /** + * @get_rate_matching: Get the supported type of rate matching for a + * particular phy interface. This is used by phy consumers to determine + * whether to advertise lower-speed modes for that interface. It is + * assumed that if a rate matching mode is supported on an interface, + * then that interface's rate can be adapted to all slower link speeds + * supported by the phy. If iface is %PHY_INTERFACE_MODE_NA, and the phy + * supports any kind of rate matching for any interface, then it must + * return that rate matching mode (preferring %RATE_MATCH_PAUSE to + * %RATE_MATCH_CRS). If the interface is not supported, this should + * return %RATE_MATCH_NONE. + */ + int (*get_rate_matching)(struct phy_device *phydev, + phy_interface_t iface); + /* PHY Power Management */ /** @suspend: Suspend the hardware, saving state if needed */ int (*suspend)(struct phy_device *phydev); @@ -971,6 +988,7 @@ struct phy_fixup { const char *phy_speed_to_str(int speed); const char *phy_duplex_to_str(unsigned int duplex); +const char *phy_rate_matching_to_str(int rate_matching); int phy_interface_num_ports(phy_interface_t interface); @@ -1687,6 +1705,8 @@ int phy_disable_interrupts(struct phy_device *phydev); void phy_request_interrupt(struct phy_device *phydev); void phy_free_interrupt(struct phy_device *phydev); void phy_print_status(struct phy_device *phydev); +int phy_get_rate_matching(struct phy_device *phydev, + phy_interface_t iface); void phy_set_max_speed(struct phy_device *phydev, u32 max_speed); void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode); void phy_advertise_supported(struct phy_device *phydev); diff --git a/include/linux/phylink.h b/include/linux/phylink.h index 6d06896fc20d..664dd409feb9 100644 --- a/include/linux/phylink.h +++ b/include/linux/phylink.h @@ -21,6 +21,35 @@ enum { MLO_AN_FIXED, /* Fixed-link mode */ MLO_AN_INBAND, /* In-band protocol */ + /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our + * autonegotiation advertisement. They correspond to the PAUSE and + * ASM_DIR bits defined by 802.3, respectively. + * + * The following table lists the values of tx_pause and rx_pause which + * might be requested in mac_link_up. The exact values depend on either + * the results of autonegotation (if MLO_PAUSE_AN is set) or user + * configuration (if MLO_PAUSE_AN is not set). + * + * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause + * ============= ============== ============ ================== + * 0 0 0 0/0 + * 0 0 1 0/0 + * 0 1 0 0/0, 0/1, 1/0, 1/1 + * 0 1 1 0/0, 1/0 + * 1 0 0 0/0, 1/1 + * 1 0 1 0/0, 1/1 + * 1 1 0 0/0, 0/1, 1/0, 1/1 + * 1 1 1 0/0, 0/1, 1/1 + * + * If you set MAC_ASYM_PAUSE, the user may request any combination of + * tx_pause and rx_pause. You do not have to support these + * combinations. + * + * However, you should support combinations of tx_pause and rx_pause + * which might be the result of autonegotation. For example, don't set + * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause + * at the same time. + */ MAC_SYM_PAUSE = BIT(0), MAC_ASYM_PAUSE = BIT(1), MAC_10HD = BIT(2), @@ -59,6 +88,10 @@ static inline bool phylink_autoneg_inband(unsigned int mode) * @speed: link speed, one of the SPEED_* constants. * @duplex: link duplex mode, one of DUPLEX_* constants. * @pause: link pause state, described by MLO_PAUSE_* constants. + * @rate_matching: rate matching being performed, one of the RATE_MATCH_* + * constants. If rate matching is taking place, then the speed/duplex of + * the medium link mode (@speed and @duplex) and the speed/duplex of the phy + * interface mode (@interface) are different. * @link: true if the link is up. * @an_enabled: true if autonegotiation is enabled/desired. * @an_complete: true if autonegotiation has completed. @@ -70,6 +103,7 @@ struct phylink_link_state { int speed; int duplex; int pause; + int rate_matching; unsigned int link:1; unsigned int an_enabled:1; unsigned int an_complete:1; @@ -518,8 +552,10 @@ void pcs_link_up(struct phylink_pcs *pcs, unsigned int mode, phy_interface_t interface, int speed, int duplex); #endif -void phylink_get_linkmodes(unsigned long *linkmodes, phy_interface_t interface, - unsigned long mac_capabilities); +void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps); +unsigned long phylink_get_capabilities(phy_interface_t interface, + unsigned long mac_capabilities, + int rate_matching); void phylink_generic_validate(struct phylink_config *config, unsigned long *supported, struct phylink_link_state *state); |