diff options
Diffstat (limited to 'include/net/cfg80211.h')
| -rw-r--r-- | include/net/cfg80211.h | 173 |
1 files changed, 145 insertions, 28 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 2a7936d7851d..bcc9f448ec4e 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -258,13 +258,9 @@ struct ieee80211_supported_band { /** * struct vif_params - describes virtual interface parameters - * @mesh_id: mesh ID to use - * @mesh_id_len: length of the mesh ID * @use_4addr: use 4-address frames */ struct vif_params { - u8 *mesh_id; - int mesh_id_len; int use_4addr; }; @@ -424,6 +420,7 @@ struct station_parameters { * @STATION_INFO_TX_RETRIES: @tx_retries filled * @STATION_INFO_TX_FAILED: @tx_failed filled * @STATION_INFO_RX_DROP_MISC: @rx_dropped_misc filled + * @STATION_INFO_SIGNAL_AVG: @signal_avg filled */ enum station_info_flags { STATION_INFO_INACTIVE_TIME = 1<<0, @@ -439,6 +436,7 @@ enum station_info_flags { STATION_INFO_TX_RETRIES = 1<<10, STATION_INFO_TX_FAILED = 1<<11, STATION_INFO_RX_DROP_MISC = 1<<12, + STATION_INFO_SIGNAL_AVG = 1<<13, }; /** @@ -485,6 +483,7 @@ struct rate_info { * @plid: mesh peer link id * @plink_state: mesh peer link state * @signal: signal strength of last received packet in dBm + * @signal_avg: signal strength average in dBm * @txrate: current unicast bitrate to this station * @rx_packets: packets received from this station * @tx_packets: packets transmitted to this station @@ -505,6 +504,7 @@ struct station_info { u16 plid; u8 plink_state; s8 signal; + s8 signal_avg; struct rate_info txrate; u32 rx_packets; u32 tx_packets; @@ -605,6 +605,8 @@ struct mpath_info { * (or NULL for no change) * @basic_rates_len: number of basic rates * @ap_isolate: do not forward packets between connected stations + * @ht_opmode: HT Operation mode + * (u16 = opmode, -1 = do not change) */ struct bss_parameters { int use_cts_prot; @@ -613,8 +615,14 @@ struct bss_parameters { u8 *basic_rates; u8 basic_rates_len; int ap_isolate; + int ht_opmode; }; +/* + * struct mesh_config - 802.11s mesh configuration + * + * These parameters can be changed while the mesh is active. + */ struct mesh_config { /* Timeouts in ms */ /* Mesh plink management parameters */ @@ -624,6 +632,8 @@ struct mesh_config { u16 dot11MeshMaxPeerLinks; u8 dot11MeshMaxRetries; u8 dot11MeshTTL; + /* ttl used in path selection information elements */ + u8 element_ttl; bool auto_open_plinks; /* HWMP parameters */ u8 dot11MeshHWMPmaxPREQretries; @@ -636,6 +646,26 @@ struct mesh_config { }; /** + * struct mesh_setup - 802.11s mesh setup configuration + * @mesh_id: the mesh ID + * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes + * @path_sel_proto: which path selection protocol to use + * @path_metric: which metric to use + * @vendor_ie: vendor information elements (optional) + * @vendor_ie_len: length of vendor information elements + * + * These parameters are fixed when the mesh is created. + */ +struct mesh_setup { + const u8 *mesh_id; + u8 mesh_id_len; + u8 path_sel_proto; + u8 path_metric; + const u8 *vendor_ie; + u8 vendor_ie_len; +}; + +/** * struct ieee80211_txq_params - TX queue parameters * @queue: TX queue identifier (NL80211_TXQ_Q_*) * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled @@ -923,6 +953,7 @@ struct cfg80211_disassoc_request { * @privacy: this is a protected network, keys will be configured * after joining * @basic_rates: bitmap of basic rates to use when creating the IBSS + * @mcast_rate: per-band multicast rate index + 1 (0: disabled) */ struct cfg80211_ibss_params { u8 *ssid; @@ -934,6 +965,7 @@ struct cfg80211_ibss_params { u32 basic_rates; bool channel_fixed; bool privacy; + int mcast_rate[IEEE80211_NUM_BANDS]; }; /** @@ -1029,7 +1061,8 @@ struct cfg80211_pmksa { * * @add_virtual_intf: create a new virtual interface with the given name, * must set the struct wireless_dev's iftype. Beware: You must create - * the new netdev in the wiphy's network namespace! + * the new netdev in the wiphy's network namespace! Returns the netdev, + * or an ERR_PTR. * * @del_virtual_intf: remove the virtual interface determined by ifindex. * @@ -1071,9 +1104,9 @@ struct cfg80211_pmksa { * @get_mpath: get a mesh path for the given parameters * @dump_mpath: dump mesh path callback -- resume dump at index @idx * - * @get_mesh_params: Put the current mesh parameters into *params + * @get_mesh_config: Get the current mesh configuration * - * @set_mesh_params: Set mesh parameters. + * @update_mesh_config: Update mesh parameters on a running mesh. * The mask is a bitfield which tells us which parameters to * set, and which to leave alone. * @@ -1132,7 +1165,9 @@ struct cfg80211_pmksa { * @cancel_remain_on_channel: Cancel an on-going remain-on-channel operation. * This allows the operation to be terminated prior to timeout based on * the duration value. - * @mgmt_tx: Transmit a management frame + * @mgmt_tx: Transmit a management frame. + * @mgmt_tx_cancel_wait: Cancel the wait time from transmitting a management + * frame on another channel * * @testmode_cmd: run a test mode command * @@ -1150,14 +1185,23 @@ struct cfg80211_pmksa { * @mgmt_frame_register: Notify driver that a management frame type was * registered. Note that this callback may not sleep, and cannot run * concurrently with itself. + * + * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. + * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may + * reject TX/RX mask combinations they cannot support by returning -EINVAL + * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX). + * + * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant). */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy); int (*resume)(struct wiphy *wiphy); - int (*add_virtual_intf)(struct wiphy *wiphy, char *name, - enum nl80211_iftype type, u32 *flags, - struct vif_params *params); + struct net_device * (*add_virtual_intf)(struct wiphy *wiphy, + char *name, + enum nl80211_iftype type, + u32 *flags, + struct vif_params *params); int (*del_virtual_intf)(struct wiphy *wiphy, struct net_device *dev); int (*change_virtual_intf)(struct wiphy *wiphy, struct net_device *dev, @@ -1175,7 +1219,7 @@ struct cfg80211_ops { u8 key_index, bool pairwise, const u8 *mac_addr); int (*set_default_key)(struct wiphy *wiphy, struct net_device *netdev, - u8 key_index); + u8 key_index, bool unicast, bool multicast); int (*set_default_mgmt_key)(struct wiphy *wiphy, struct net_device *netdev, u8 key_index); @@ -1210,12 +1254,17 @@ struct cfg80211_ops { int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev, int idx, u8 *dst, u8 *next_hop, struct mpath_info *pinfo); - int (*get_mesh_params)(struct wiphy *wiphy, + int (*get_mesh_config)(struct wiphy *wiphy, struct net_device *dev, struct mesh_config *conf); - int (*set_mesh_params)(struct wiphy *wiphy, - struct net_device *dev, - const struct mesh_config *nconf, u32 mask); + int (*update_mesh_config)(struct wiphy *wiphy, + struct net_device *dev, u32 mask, + const struct mesh_config *nconf); + int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev, + const struct mesh_config *conf, + const struct mesh_setup *setup); + int (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev); + int (*change_bss)(struct wiphy *wiphy, struct net_device *dev, struct bss_parameters *params); @@ -1289,10 +1338,13 @@ struct cfg80211_ops { u64 cookie); int (*mgmt_tx)(struct wiphy *wiphy, struct net_device *dev, - struct ieee80211_channel *chan, + struct ieee80211_channel *chan, bool offchan, enum nl80211_channel_type channel_type, - bool channel_type_valid, + bool channel_type_valid, unsigned int wait, const u8 *buf, size_t len, u64 *cookie); + int (*mgmt_tx_cancel_wait)(struct wiphy *wiphy, + struct net_device *dev, + u64 cookie); int (*set_power_mgmt)(struct wiphy *wiphy, struct net_device *dev, bool enabled, int timeout); @@ -1304,6 +1356,9 @@ struct cfg80211_ops { void (*mgmt_frame_register)(struct wiphy *wiphy, struct net_device *dev, u16 frame_type, bool reg); + + int (*set_antenna)(struct wiphy *wiphy, u32 tx_ant, u32 rx_ant); + int (*get_antenna)(struct wiphy *wiphy, u32 *tx_ant, u32 *rx_ant); }; /* @@ -1321,13 +1376,14 @@ struct cfg80211_ops { * initiator is %REGDOM_SET_BY_CORE). * @WIPHY_FLAG_STRICT_REGULATORY: tells us the driver for this device will * ignore regulatory domain settings until it gets its own regulatory - * domain via its regulatory_hint(). After its gets its own regulatory - * domain it will only allow further regulatory domain settings to - * further enhance compliance. For example if channel 13 and 14 are - * disabled by this regulatory domain no user regulatory domain can - * enable these channels at a later time. This can be used for devices - * which do not have calibration information gauranteed for frequencies - * or settings outside of its regulatory domain. + * domain via its regulatory_hint() unless the regulatory hint is + * from a country IE. After its gets its own regulatory domain it will + * only allow further regulatory domain settings to further enhance + * compliance. For example if channel 13 and 14 are disabled by this + * regulatory domain no user regulatory domain can enable these channels + * at a later time. This can be used for devices which do not have + * calibration information guaranteed for frequencies or settings + * outside of its regulatory domain. * @WIPHY_FLAG_DISABLE_BEACON_HINTS: enable this if your driver needs to ensure * that passive scan flags and beaconing flags may not be lifted by * cfg80211 due to regulatory beacon hints. For more information on beacon @@ -1345,6 +1401,8 @@ struct cfg80211_ops { * control port protocol ethertype. The device also honours the * control_port_no_encrypt flag. * @WIPHY_FLAG_IBSS_RSN: The device supports IBSS RSN. + * @WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS: The device supports separate + * unicast and multicast TX keys. */ enum wiphy_flags { WIPHY_FLAG_CUSTOM_REGULATORY = BIT(0), @@ -1355,7 +1413,8 @@ enum wiphy_flags { WIPHY_FLAG_4ADDR_AP = BIT(5), WIPHY_FLAG_4ADDR_STATION = BIT(6), WIPHY_FLAG_CONTROL_PORT_PROTOCOL = BIT(7), - WIPHY_FLAG_IBSS_RSN = BIT(7), + WIPHY_FLAG_IBSS_RSN = BIT(8), + WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS= BIT(9), }; struct mac_address { @@ -1368,7 +1427,9 @@ struct ieee80211_txrx_stypes { /** * struct wiphy - wireless hardware description - * @reg_notifier: the driver's regulatory notification callback + * @reg_notifier: the driver's regulatory notification callback, + * note that if your driver uses wiphy_apply_custom_regulatory() + * the reg_notifier's request can be passed as NULL * @regd: the driver's regulatory domain, if one was requested via * the regulatory_hint() API. This can be used by the driver * on the reg_notifier() if it chooses to ignore future @@ -1420,6 +1481,17 @@ struct ieee80211_txrx_stypes { * @mgmt_stypes: bitmasks of frame subtypes that can be subscribed to or * transmitted through nl80211, points to an array indexed by interface * type + * + * @available_antennas_tx: bitmap of antennas which are available to be + * configured as TX antennas. Antenna configuration commands will be + * rejected unless this or @available_antennas_rx is set. + * + * @available_antennas_rx: bitmap of antennas which are available to be + * configured as RX antennas. Antenna configuration commands will be + * rejected unless this or @available_antennas_tx is set. + * + * @max_remain_on_channel_duration: Maximum time a remain-on-channel operation + * may request, if implemented. */ struct wiphy { /* assign these fields before you register the wiphy */ @@ -1457,8 +1529,13 @@ struct wiphy { char fw_version[ETHTOOL_BUSINFO_LEN]; u32 hw_version; + u16 max_remain_on_channel_duration; + u8 max_num_pmkids; + u32 available_antennas_tx; + u32 available_antennas_rx; + /* If multiple wiphys are registered and you're handed e.g. * a regular netdev with assigned ieee80211_ptr, you won't * know whether it points to a wiphy your driver has registered @@ -1624,6 +1701,8 @@ struct cfg80211_cached_keys; * @bssid: (private) Used by the internal configuration code * @ssid: (private) Used by the internal configuration code * @ssid_len: (private) Used by the internal configuration code + * @mesh_id_len: (private) Used by the internal configuration code + * @mesh_id_up_len: (private) Used by the internal configuration code * @wext: (private) Used by the internal wireless extensions compat code * @use_4addr: indicates 4addr mode is used on this interface, must be * set by driver (if supported) on add_interface BEFORE registering the @@ -1653,7 +1732,7 @@ struct wireless_dev { /* currently used for IBSS and SME - might be rearranged later */ u8 ssid[IEEE80211_MAX_SSID_LEN]; - u8 ssid_len; + u8 ssid_len, mesh_id_len, mesh_id_up_len; enum { CFG80211_SME_IDLE, CFG80211_SME_CONNECTING, @@ -2297,6 +2376,32 @@ void __cfg80211_send_disassoc(struct net_device *dev, const u8 *buf, size_t len); /** + * cfg80211_send_unprot_deauth - notification of unprotected deauthentication + * @dev: network device + * @buf: deauthentication frame (header + body) + * @len: length of the frame data + * + * This function is called whenever a received Deauthentication frame has been + * dropped in station mode because of MFP being used but the Deauthentication + * frame was not protected. This function may sleep. + */ +void cfg80211_send_unprot_deauth(struct net_device *dev, const u8 *buf, + size_t len); + +/** + * cfg80211_send_unprot_disassoc - notification of unprotected disassociation + * @dev: network device + * @buf: disassociation frame (header + body) + * @len: length of the frame data + * + * This function is called whenever a received Disassociation frame has been + * dropped in station mode because of MFP being used but the Disassociation + * frame was not protected. This function may sleep. + */ +void cfg80211_send_unprot_disassoc(struct net_device *dev, const u8 *buf, + size_t len); + +/** * cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP) * @dev: network device * @addr: The source MAC address of the frame @@ -2595,6 +2700,18 @@ void cfg80211_cqm_rssi_notify(struct net_device *dev, enum nl80211_cqm_rssi_threshold_event rssi_event, gfp_t gfp); +/** + * cfg80211_cqm_pktloss_notify - notify userspace about packetloss to peer + * @dev: network device + * @peer: peer's MAC address + * @num_packets: how many packets were lost -- should be a fixed threshold + * but probably no less than maybe 50, or maybe a throughput dependent + * threshold (to account for temporary interference) + * @gfp: context flags + */ +void cfg80211_cqm_pktloss_notify(struct net_device *dev, + const u8 *peer, u32 num_packets, gfp_t gfp); + /* Logging, debugging and troubleshooting/diagnostic helpers. */ /* wiphy_printk helpers, similar to dev_printk */ |