diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 21 |
1 files changed, 11 insertions, 10 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 78908b516f42..54aa16b98b76 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -145,6 +145,7 @@ struct ieee80211_low_level_stats { * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be * enabled/disabled (beaconing modes) * @BSS_CHANGED_CQM: Connection quality monitor config changed + * @BSS_CHANGED_IBSS: IBSS join status changed */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -158,6 +159,7 @@ enum ieee80211_bss_change { BSS_CHANGED_BEACON = 1<<8, BSS_CHANGED_BEACON_ENABLED = 1<<9, BSS_CHANGED_CQM = 1<<10, + BSS_CHANGED_IBSS = 1<<11, }; /** @@ -167,6 +169,8 @@ enum ieee80211_bss_change { * to that BSS) that can change during the lifetime of the BSS. * * @assoc: association status + * @ibss_joined: indicates whether this station is part of an IBSS + * or not * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection * @use_short_preamble: use 802.11b short preamble; @@ -194,7 +198,7 @@ enum ieee80211_bss_change { struct ieee80211_bss_conf { const u8 *bssid; /* association related data */ - bool assoc; + bool assoc, ibss_joined; u16 aid; /* erp related data */ bool use_cts_prot; @@ -556,7 +560,6 @@ enum mac80211_rx_flags { * @signal: signal strength when receiving this frame, either in dBm, in dB or * unspecified depending on the hardware capabilities flags * @IEEE80211_HW_SIGNAL_* - * @noise: noise when receiving this frame, in dBm (DEPRECATED). * @antenna: antenna used * @rate_idx: index of data rate into band's supported rates or MCS index if * HT rates are use (RX_FLAG_HT) @@ -567,7 +570,6 @@ struct ieee80211_rx_status { enum ieee80211_band band; int freq; int signal; - int noise __deprecated; int antenna; int rate_idx; int flag; @@ -668,6 +670,9 @@ enum ieee80211_smps_mode { * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the * powersave documentation below. This variable is valid only when * the CONF_PS flag is set. + * @dynamic_ps_forced_timeout: The dynamic powersave timeout (in ms) configured + * by cfg80211 (essentially, wext) If set, this value overrules the value + * chosen by mac80211 based on ps qos network latency. * * @power_level: requested transmit power (in dBm) * @@ -687,7 +692,7 @@ enum ieee80211_smps_mode { */ struct ieee80211_conf { u32 flags; - int power_level, dynamic_ps_timeout; + int power_level, dynamic_ps_timeout, dynamic_ps_forced_timeout; int max_sleep_period; u16 listen_interval; @@ -927,10 +932,6 @@ enum ieee80211_tkip_key_type { * one milliwatt. This is the preferred method since it is standardized * between different devices. @max_signal does not need to be set. * - * @IEEE80211_HW_NOISE_DBM: - * Hardware can provide noise (radio interference) values in units dBm, - * decibel difference from one milliwatt. - * * @IEEE80211_HW_SPECTRUM_MGMT: * Hardware supports spectrum management defined in 802.11h * Measurement, Channel Switch, Quieting, TPC @@ -994,7 +995,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, IEEE80211_HW_SIGNAL_DBM = 1<<6, - IEEE80211_HW_NOISE_DBM = 1<<7, + /* use this hole */ IEEE80211_HW_SPECTRUM_MGMT = 1<<8, IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, IEEE80211_HW_SUPPORTS_PS = 1<<10, @@ -1654,7 +1655,7 @@ struct ieee80211_ops { struct ieee80211_key_conf *conf, struct ieee80211_sta *sta, u32 iv32, u16 *phase1key); - int (*hw_scan)(struct ieee80211_hw *hw, + int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_scan_request *req); void (*sw_scan_start)(struct ieee80211_hw *hw); void (*sw_scan_complete)(struct ieee80211_hw *hw); |