diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 24 |
1 files changed, 14 insertions, 10 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index b52721008be8..ff137fd7714f 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -177,9 +177,10 @@ enum ieee80211_bss_change { * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection * @use_short_preamble: use 802.11b short preamble + * @dtim_period: num of beacons before the next DTIM, for PSM * @timestamp: beacon timestamp * @beacon_int: beacon interval - * @assoc_capability: capabbilities taken from assoc resp + * @assoc_capability: capabilities taken from assoc resp * @assoc_ht: association in HT mode * @ht_conf: ht capabilities * @ht_bss_conf: ht extended capabilities @@ -191,6 +192,7 @@ struct ieee80211_bss_conf { /* erp related data */ bool use_cts_prot; bool use_short_preamble; + u8 dtim_period; u16 beacon_int; u16 assoc_capability; u64 timestamp; @@ -430,6 +432,7 @@ enum ieee80211_conf_flags { * @radio_enabled: when zero, driver is required to switch off the radio. * TODO make a flag * @beacon_int: beacon interval (TODO make interface config) + * @listen_interval: listen interval in units of beacon interval * @flags: configuration flags defined above * @power_level: requested transmit power (in dBm) * @max_antenna_gain: maximum antenna gain (in dBi) @@ -444,6 +447,7 @@ struct ieee80211_conf { int radio_enabled; int beacon_int; + u16 listen_interval; u32 flags; int power_level; int max_antenna_gain; @@ -704,10 +708,7 @@ enum ieee80211_tkip_key_type { * rely on the host system for such buffering. This option is used * to configure the IEEE 802.11 upper layer to buffer broadcast and * multicast frames when there are power saving stations so that - * the driver can fetch them with ieee80211_get_buffered_bc(). Note - * that not setting this flag works properly only when the - * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because - * otherwise the stack will not know when the DTIM beacon was sent. + * the driver can fetch them with ieee80211_get_buffered_bc(). * * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: * Hardware is not capable of short slot operation on the 2.4 GHz band. @@ -785,6 +786,9 @@ enum ieee80211_hw_flags { * @max_signal: Maximum value for signal (rssi) in RX information, used * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB * + * @max_listen_interval: max listen interval in units of beacon interval + * that HW supports + * * @queues: number of available hardware transmit queues for * data packets. WMM/QoS requires at least four, these * queues need to have configurable access parameters. @@ -812,7 +816,9 @@ struct ieee80211_hw { unsigned int extra_tx_headroom; int channel_change_time; int vif_data_size; - u16 queues, ampdu_queues; + u16 queues; + u16 ampdu_queues; + u16 max_listen_interval; s8 max_signal; }; @@ -1090,10 +1096,8 @@ enum ieee80211_ampdu_mlme_action { * See the section "Frame filtering" for more information. * This callback must be implemented and atomic. * - * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon - * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set) - * mac80211 calls this function when a TIM bit must be set or cleared - * for a given AID. Must be atomic. + * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit + * must be set or cleared for a given AID. Must be atomic. * * @set_key: See the section "Hardware crypto acceleration" * This callback can sleep, and is only called between add_interface |