diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 67 |
1 files changed, 55 insertions, 12 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index e5f02909f1ad..ab94dbc331a0 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -152,11 +152,14 @@ struct ieee80211_low_level_stats { * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed + * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel, + * this is used only with channel switching with CSA */ enum ieee80211_chanctx_change { IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), + IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3), }; /** @@ -811,6 +814,8 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC * is stored in the @ampdu_delimiter_crc field) * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 + * @RX_FLAG_10MHZ: 10 MHz (half channel) was used + * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used */ enum mac80211_rx_flags { RX_FLAG_MMIC_ERROR = BIT(0), @@ -839,6 +844,8 @@ enum mac80211_rx_flags { RX_FLAG_80P80MHZ = BIT(24), RX_FLAG_160MHZ = BIT(25), RX_FLAG_STBC_MASK = BIT(26) | BIT(27), + RX_FLAG_10MHZ = BIT(28), + RX_FLAG_5MHZ = BIT(29), }; #define RX_FLAG_STBC_SHIFT 26 @@ -1004,11 +1011,11 @@ enum ieee80211_smps_mode { * @radar_enabled: whether radar detection is enabled * * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame - * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, - * but actually means the number of transmissions not the number of retries + * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, + * but actually means the number of transmissions not the number of retries * @short_frame_max_tx_count: Maximum number of transmissions for a "short" - * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the - * number of transmissions not the number of retries + * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the + * number of transmissions not the number of retries * * @smps_mode: spatial multiplexing powersave mode; note that * %IEEE80211_SMPS_STATIC is used when the device is not @@ -1080,6 +1087,7 @@ enum ieee80211_vif_flags { * @addr: address of this interface * @p2p: indicates whether this AP or STA interface is a p2p * interface, i.e. a GO or p2p-sta respectively + * @csa_active: marks whether a channel switch is going on * @driver_flags: flags/capabilities the driver has for this interface, * these need to be set (or cleared) when the interface is added * or, if supported by the driver, the interface type is changed @@ -1092,7 +1100,7 @@ enum ieee80211_vif_flags { * be off when it is %NULL there can still be races and packets could be * processed after it switches back to %NULL. * @debugfs_dir: debugfs dentry, can be used by drivers to create own per - * interface debug files. Note that it will be NULL for the virtual + * interface debug files. Note that it will be NULL for the virtual * monitor interface (if that is requested.) * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *). @@ -1102,6 +1110,7 @@ struct ieee80211_vif { struct ieee80211_bss_conf bss_conf; u8 addr[ETH_ALEN]; bool p2p; + bool csa_active; u8 cab_queue; u8 hw_queue[IEEE80211_NUM_ACS]; @@ -1425,10 +1434,10 @@ struct ieee80211_tx_control { * the stack. * * @IEEE80211_HW_CONNECTION_MONITOR: - * The hardware performs its own connection monitoring, including - * periodic keep-alives to the AP and probing the AP on beacon loss. - * When this flag is set, signaling beacon-loss will cause an immediate - * change to disassociated state. + * The hardware performs its own connection monitoring, including + * periodic keep-alives to the AP and probing the AP on beacon loss. + * When this flag is set, signaling beacon-loss will cause an immediate + * change to disassociated state. * * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: * This device needs to get data from beacon before association (i.e. @@ -1526,10 +1535,10 @@ enum ieee80211_hw_flags { * @channel_change_time: time (in microseconds) it takes to change channels. * * @max_signal: Maximum value for signal (rssi) in RX information, used - * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB + * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB * * @max_listen_interval: max listen interval in units of beacon interval - * that HW supports + * that HW supports * * @queues: number of available hardware transmit queues for * data packets. WMM/QoS requires at least four, these @@ -2443,7 +2452,7 @@ enum ieee80211_roc_type { * The callback can sleep. * * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. - * Currently, this is only used for IBSS mode debugging. Is not a + * Currently, this is only used for IBSS mode debugging. Is not a * required function. * The callback can sleep. * @@ -2633,6 +2642,16 @@ enum ieee80211_roc_type { * @ipv6_addr_change: IPv6 address assignment on the given interface changed. * Currently, this is only called for managed or P2P client interfaces. * This callback is optional; it must not sleep. + * + * @channel_switch_beacon: Starts a channel switch to a new channel. + * Beacons are modified to include CSA or ECSA IEs before calling this + * function. The corresponding count fields in these IEs must be + * decremented, and when they reach zero the driver must call + * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get() + * get the csa counter decremented by mac80211, but must check if it is + * zero using ieee80211_csa_is_complete() after the beacon has been + * transmitted and then call ieee80211_csa_finish(). + * */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2820,6 +2839,9 @@ struct ieee80211_ops { struct ieee80211_vif *vif, struct inet6_dev *idev); #endif + void (*channel_switch_beacon)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct cfg80211_chan_def *chandef); }; /** @@ -3315,6 +3337,25 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, } /** + * ieee80211_csa_finish - notify mac80211 about channel switch + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * After a channel switch announcement was scheduled and the counter in this + * announcement hit zero, this function must be called by the driver to + * notify mac80211 that the channel can be changed. + */ +void ieee80211_csa_finish(struct ieee80211_vif *vif); + +/** + * ieee80211_csa_is_complete - find out if counters reached zero + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * This function returns whether the channel switch counters reached zero. + */ +bool ieee80211_csa_is_complete(struct ieee80211_vif *vif); + + +/** * ieee80211_proberesp_get - retrieve a Probe Response template * @hw: pointer obtained from ieee80211_alloc_hw(). * @vif: &struct ieee80211_vif pointer from the add_interface callback. @@ -4204,8 +4245,10 @@ struct rate_control_ops { void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp); void (*rate_init)(void *priv, struct ieee80211_supported_band *sband, + struct cfg80211_chan_def *chandef, struct ieee80211_sta *sta, void *priv_sta); void (*rate_update)(void *priv, struct ieee80211_supported_band *sband, + struct cfg80211_chan_def *chandef, struct ieee80211_sta *sta, void *priv_sta, u32 changed); void (*free_sta)(void *priv, struct ieee80211_sta *sta, |