diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 29 |
1 files changed, 29 insertions, 0 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 2e752df57510..9edba09547e4 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -164,6 +164,7 @@ struct ieee80211_low_level_stats { * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note * that it is only ever disabled for station mode. * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. + * @BSS_CHANGED_SSID: SSID changed for this BSS (AP mode) */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -181,6 +182,7 @@ enum ieee80211_bss_change { BSS_CHANGED_ARP_FILTER = 1<<12, BSS_CHANGED_QOS = 1<<13, BSS_CHANGED_IDLE = 1<<14, + BSS_CHANGED_SSID = 1<<15, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -254,6 +256,9 @@ enum ieee80211_rssi_event { * @idle: This interface is idle. There's also a global idle flag in the * hardware config which may be more appropriate depending on what * your driver/device needs to do. + * @ssid: The SSID of the current vif. Only valid in AP-mode. + * @ssid_len: Length of SSID given in @ssid. + * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode. */ struct ieee80211_bss_conf { const u8 *bssid; @@ -280,6 +285,9 @@ struct ieee80211_bss_conf { bool arp_filter_enabled; bool qos; bool idle; + u8 ssid[IEEE80211_MAX_SSID_LEN]; + size_t ssid_len; + bool hidden_ssid; }; /** @@ -947,6 +955,9 @@ enum set_key_cmd { * @wme: indicates whether the STA supports WME. Only valid during AP-mode. * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *), size is determined in hw information. + * @uapsd_queues: bitmap of queues configured for uapsd. Only valid + * if wme is supported. + * @max_sp: max Service Period. Only valid if wme is supported. */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1096,6 +1107,10 @@ enum sta_notify_cmd { * stations based on the PM bit of incoming frames. * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure * the PS mode of connected stations. + * + * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session + * setup strictly in HW. mac80211 should not attempt to do this in + * software. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1121,6 +1136,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20, IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, IEEE80211_HW_AP_LINK_PS = 1<<22, + IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23, }; /** @@ -3220,6 +3236,19 @@ void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw); void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap, const u8 *addr); +/** + * ieee80211_send_bar - send a BlockAckReq frame + * + * can be used to flush pending frames from the peer's aggregation reorder + * buffer. + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @ra: the peer's destination address + * @tid: the TID of the aggregation session + * @ssn: the new starting sequence number for the receiver + */ +void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn); + /* Rate control API */ /** |