diff options
Diffstat (limited to 'include/uapi/linux/mdio.h')
| -rw-r--r-- | include/uapi/linux/mdio.h | 112 |
1 files changed, 112 insertions, 0 deletions
diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h index 4bcb41c71b8c..75b7257a51e1 100644 --- a/include/uapi/linux/mdio.h +++ b/include/uapi/linux/mdio.h @@ -53,18 +53,33 @@ #define MDIO_AN_EEE_LPABLE 61 /* EEE link partner ability */ #define MDIO_AN_EEE_ADV2 62 /* EEE advertisement 2 */ #define MDIO_AN_EEE_LPABLE2 63 /* EEE link partner ability 2 */ +#define MDIO_AN_CTRL2 64 /* AN THP bypass request control */ /* Media-dependent registers. */ #define MDIO_PMA_10GBT_SWAPPOL 130 /* 10GBASE-T pair swap & polarity */ #define MDIO_PMA_10GBT_TXPWR 131 /* 10GBASE-T TX power control */ #define MDIO_PMA_10GBT_SNR 133 /* 10GBASE-T SNR margin, lane A. * Lanes B-D are numbered 134-136. */ +#define MDIO_PMA_10GBR_FSRT_CSR 147 /* 10GBASE-R fast retrain status and control */ #define MDIO_PMA_10GBR_FECABLE 170 /* 10GBASE-R FEC ability */ #define MDIO_PCS_10GBX_STAT1 24 /* 10GBASE-X PCS status 1 */ #define MDIO_PCS_10GBRT_STAT1 32 /* 10GBASE-R/-T PCS status 1 */ #define MDIO_PCS_10GBRT_STAT2 33 /* 10GBASE-R/-T PCS status 2 */ #define MDIO_AN_10GBT_CTRL 32 /* 10GBASE-T auto-negotiation control */ #define MDIO_AN_10GBT_STAT 33 /* 10GBASE-T auto-negotiation status */ +#define MDIO_B10L_PMA_CTRL 2294 /* 10BASE-T1L PMA control */ +#define MDIO_PMA_10T1L_STAT 2295 /* 10BASE-T1L PMA status */ +#define MDIO_PCS_10T1L_CTRL 2278 /* 10BASE-T1L PCS control */ +#define MDIO_PMA_PMD_BT1 18 /* BASE-T1 PMA/PMD extended ability */ +#define MDIO_AN_T1_CTRL 512 /* BASE-T1 AN control */ +#define MDIO_AN_T1_STAT 513 /* BASE-T1 AN status */ +#define MDIO_AN_T1_ADV_L 514 /* BASE-T1 AN advertisement register [15:0] */ +#define MDIO_AN_T1_ADV_M 515 /* BASE-T1 AN advertisement register [31:16] */ +#define MDIO_AN_T1_ADV_H 516 /* BASE-T1 AN advertisement register [47:32] */ +#define MDIO_AN_T1_LP_L 517 /* BASE-T1 AN LP Base Page ability register [15:0] */ +#define MDIO_AN_T1_LP_M 518 /* BASE-T1 AN LP Base Page ability register [31:16] */ +#define MDIO_AN_T1_LP_H 519 /* BASE-T1 AN LP Base Page ability register [47:32] */ +#define MDIO_PMA_PMD_BT1_CTRL 2100 /* BASE-T1 PMA/PMD control register */ /* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */ #define MDIO_PMA_LASI_RXCTRL 0x9000 /* RX_ALARM control */ @@ -120,6 +135,8 @@ #define MDIO_PMA_SPEED_100 0x0020 /* 100M capable */ #define MDIO_PMA_SPEED_10 0x0040 /* 10M capable */ #define MDIO_PCS_SPEED_10P2B 0x0002 /* 10PASS-TS/2BASE-TL capable */ +#define MDIO_PCS_SPEED_2_5G 0x0040 /* 2.5G capable */ +#define MDIO_PCS_SPEED_5G 0x0080 /* 5G capable */ /* Device present registers. */ #define MDIO_DEVS_PRESENT(devad) (1 << (devad)) @@ -155,6 +172,7 @@ #define MDIO_PMA_CTRL2_10BT 0x000f /* 10BASE-T type */ #define MDIO_PMA_CTRL2_2_5GBT 0x0030 /* 2.5GBaseT type */ #define MDIO_PMA_CTRL2_5GBT 0x0031 /* 5GBaseT type */ +#define MDIO_PMA_CTRL2_BASET1 0x003D /* BASE-T1 type */ #define MDIO_PCS_CTRL2_TYPE 0x0003 /* PCS type selection */ #define MDIO_PCS_CTRL2_10GBR 0x0000 /* 10GBASE-R type */ #define MDIO_PCS_CTRL2_10GBX 0x0001 /* 10GBASE-X type */ @@ -208,6 +226,7 @@ #define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */ #define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */ #define MDIO_PMA_EXTABLE_10BT 0x0100 /* 10BASE-T ability */ +#define MDIO_PMA_EXTABLE_BT1 0x0800 /* BASE-T1 ability */ #define MDIO_PMA_EXTABLE_NBT 0x4000 /* 2.5/5GBASE-T ability */ /* PHY XGXS lane state register. */ @@ -237,6 +256,9 @@ #define MDIO_PMA_10GBR_FECABLE_ABLE 0x0001 /* FEC ability */ #define MDIO_PMA_10GBR_FECABLE_ERRABLE 0x0002 /* FEC error indic. ability */ +/* PMA 10GBASE-R Fast Retrain status and control register. */ +#define MDIO_PMA_10GBR_FSRT_ENABLE 0x0001 /* Fast retrain enable */ + /* PCS 10GBASE-R/-T status register 1. */ #define MDIO_PCS_10GBRT_STAT1_BLKLK 0x0001 /* Block lock attained */ @@ -245,6 +267,7 @@ #define MDIO_PCS_10GBRT_STAT2_BER 0x3f00 /* AN 10GBASE-T control register. */ +#define MDIO_AN_10GBT_CTRL_ADVFSRT2_5G 0x0020 /* Advertise 2.5GBASE-T fast retrain */ #define MDIO_AN_10GBT_CTRL_ADV2_5G 0x0080 /* Advertise 2.5GBASE-T */ #define MDIO_AN_10GBT_CTRL_ADV5G 0x0100 /* Advertise 5GBASE-T */ #define MDIO_AN_10GBT_CTRL_ADV10G 0x1000 /* Advertise 10GBASE-T */ @@ -260,6 +283,66 @@ #define MDIO_AN_10GBT_STAT_MS 0x4000 /* Master/slave config */ #define MDIO_AN_10GBT_STAT_MSFLT 0x8000 /* Master/slave config fault */ +/* 10BASE-T1L PMA control */ +#define MDIO_PMA_10T1L_CTRL_LB_EN 0x0001 /* Enable loopback mode */ +#define MDIO_PMA_10T1L_CTRL_EEE_EN 0x0400 /* Enable EEE mode */ +#define MDIO_PMA_10T1L_CTRL_LOW_POWER 0x0800 /* Low-power mode */ +#define MDIO_PMA_10T1L_CTRL_2V4_EN 0x1000 /* Enable 2.4 Vpp operating mode */ +#define MDIO_PMA_10T1L_CTRL_TX_DIS 0x4000 /* Transmit disable */ +#define MDIO_PMA_10T1L_CTRL_PMA_RST 0x8000 /* MA reset */ + +/* 10BASE-T1L PMA status register. */ +#define MDIO_PMA_10T1L_STAT_LINK 0x0001 /* PMA receive link up */ +#define MDIO_PMA_10T1L_STAT_FAULT 0x0002 /* Fault condition detected */ +#define MDIO_PMA_10T1L_STAT_POLARITY 0x0004 /* Receive polarity is reversed */ +#define MDIO_PMA_10T1L_STAT_RECV_FAULT 0x0200 /* Able to detect fault on receive path */ +#define MDIO_PMA_10T1L_STAT_EEE 0x0400 /* PHY has EEE ability */ +#define MDIO_PMA_10T1L_STAT_LOW_POWER 0x0800 /* PMA has low-power ability */ +#define MDIO_PMA_10T1L_STAT_2V4_ABLE 0x1000 /* PHY has 2.4 Vpp operating mode ability */ +#define MDIO_PMA_10T1L_STAT_LB_ABLE 0x2000 /* PHY has loopback ability */ + +/* 10BASE-T1L PCS control register. */ +#define MDIO_PCS_10T1L_CTRL_LB 0x4000 /* Enable PCS level loopback mode */ +#define MDIO_PCS_10T1L_CTRL_RESET 0x8000 /* PCS reset */ + +/* BASE-T1 PMA/PMD extended ability register. */ +#define MDIO_PMA_PMD_BT1_B10L_ABLE 0x0004 /* 10BASE-T1L Ability */ + +/* BASE-T1 auto-negotiation advertisement register [15:0] */ +#define MDIO_AN_T1_ADV_L_PAUSE_CAP ADVERTISE_PAUSE_CAP +#define MDIO_AN_T1_ADV_L_PAUSE_ASYM ADVERTISE_PAUSE_ASYM +#define MDIO_AN_T1_ADV_L_FORCE_MS 0x1000 /* Force Master/slave Configuration */ +#define MDIO_AN_T1_ADV_L_REMOTE_FAULT ADVERTISE_RFAULT +#define MDIO_AN_T1_ADV_L_ACK ADVERTISE_LPACK +#define MDIO_AN_T1_ADV_L_NEXT_PAGE_REQ ADVERTISE_NPAGE + +/* BASE-T1 auto-negotiation advertisement register [31:16] */ +#define MDIO_AN_T1_ADV_M_B10L 0x4000 /* device is compatible with 10BASE-T1L */ +#define MDIO_AN_T1_ADV_M_MST 0x0010 /* advertise master preference */ + +/* BASE-T1 auto-negotiation advertisement register [47:32] */ +#define MDIO_AN_T1_ADV_H_10L_TX_HI_REQ 0x1000 /* 10BASE-T1L High Level Transmit Request */ +#define MDIO_AN_T1_ADV_H_10L_TX_HI 0x2000 /* 10BASE-T1L High Level Transmit Ability */ + +/* BASE-T1 AN LP Base Page ability register [15:0] */ +#define MDIO_AN_T1_LP_L_PAUSE_CAP LPA_PAUSE_CAP +#define MDIO_AN_T1_LP_L_PAUSE_ASYM LPA_PAUSE_ASYM +#define MDIO_AN_T1_LP_L_FORCE_MS 0x1000 /* LP Force Master/slave Configuration */ +#define MDIO_AN_T1_LP_L_REMOTE_FAULT LPA_RFAULT +#define MDIO_AN_T1_LP_L_ACK LPA_LPACK +#define MDIO_AN_T1_LP_L_NEXT_PAGE_REQ LPA_NPAGE + +/* BASE-T1 AN LP Base Page ability register [31:16] */ +#define MDIO_AN_T1_LP_M_MST 0x0010 /* LP master preference */ +#define MDIO_AN_T1_LP_M_B10L 0x4000 /* LP is compatible with 10BASE-T1L */ + +/* BASE-T1 AN LP Base Page ability register [47:32] */ +#define MDIO_AN_T1_LP_H_10L_TX_HI_REQ 0x1000 /* 10BASE-T1L High Level LP Transmit Request */ +#define MDIO_AN_T1_LP_H_10L_TX_HI 0x2000 /* 10BASE-T1L High Level LP Transmit Ability */ + +/* BASE-T1 PMA/PMD control register */ +#define MDIO_PMA_PMD_BT1_CTRL_CFG_MST 0x4000 /* MASTER-SLAVE config value */ + /* EEE Supported/Advertisement/LP Advertisement registers. * * EEE capability Register (3.20), Advertisement (7.60) and @@ -287,6 +370,9 @@ #define MDIO_EEE_2_5GT 0x0001 /* 2.5GT EEE cap */ #define MDIO_EEE_5GT 0x0002 /* 5GT EEE cap */ +/* AN MultiGBASE-T AN control 2 */ +#define MDIO_AN_THP_BP2_5GT 0x0008 /* 2.5GT THP bypass request */ + /* 2.5G/5G Extended abilities register. */ #define MDIO_PMA_NG_EXTABLE_2_5GBT 0x0001 /* 2.5GBASET ability */ #define MDIO_PMA_NG_EXTABLE_5GBT 0x0002 /* 5GBASET ability */ @@ -324,4 +410,30 @@ static inline __u16 mdio_phy_id_c45(int prtad, int devad) return MDIO_PHY_ID_C45 | (prtad << 5) | devad; } +/* UsxgmiiChannelInfo[15:0] for USXGMII in-band auto-negotiation.*/ +#define MDIO_USXGMII_EEE_CLK_STP 0x0080 /* EEE clock stop supported */ +#define MDIO_USXGMII_EEE 0x0100 /* EEE supported */ +#define MDIO_USXGMII_SPD_MASK 0x0e00 /* USXGMII speed mask */ +#define MDIO_USXGMII_FULL_DUPLEX 0x1000 /* USXGMII full duplex */ +#define MDIO_USXGMII_DPX_SPD_MASK 0x1e00 /* USXGMII duplex and speed bits */ +#define MDIO_USXGMII_10 0x0000 /* 10Mbps */ +#define MDIO_USXGMII_10HALF 0x0000 /* 10Mbps half-duplex */ +#define MDIO_USXGMII_10FULL 0x1000 /* 10Mbps full-duplex */ +#define MDIO_USXGMII_100 0x0200 /* 100Mbps */ +#define MDIO_USXGMII_100HALF 0x0200 /* 100Mbps half-duplex */ +#define MDIO_USXGMII_100FULL 0x1200 /* 100Mbps full-duplex */ +#define MDIO_USXGMII_1000 0x0400 /* 1000Mbps */ +#define MDIO_USXGMII_1000HALF 0x0400 /* 1000Mbps half-duplex */ +#define MDIO_USXGMII_1000FULL 0x1400 /* 1000Mbps full-duplex */ +#define MDIO_USXGMII_10G 0x0600 /* 10Gbps */ +#define MDIO_USXGMII_10GHALF 0x0600 /* 10Gbps half-duplex */ +#define MDIO_USXGMII_10GFULL 0x1600 /* 10Gbps full-duplex */ +#define MDIO_USXGMII_2500 0x0800 /* 2500Mbps */ +#define MDIO_USXGMII_2500HALF 0x0800 /* 2500Mbps half-duplex */ +#define MDIO_USXGMII_2500FULL 0x1800 /* 2500Mbps full-duplex */ +#define MDIO_USXGMII_5000 0x0a00 /* 5000Mbps */ +#define MDIO_USXGMII_5000HALF 0x0a00 /* 5000Mbps half-duplex */ +#define MDIO_USXGMII_5000FULL 0x1a00 /* 5000Mbps full-duplex */ +#define MDIO_USXGMII_LINK 0x8000 /* PHY link with copper-side partner */ + #endif /* _UAPI__LINUX_MDIO_H__ */ |