| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The highest-performance mode for the Cortex-A57 CPU cores supported on
R-Car H3Ne (R8A779M8) is the Power Optimized (1.5 GHz) mode. The Normal
(1.6 GHz) and High Performance (1.7 GHz) modes are not supported.
Hence drop the "turbo-mode" entries from the operating points table
inherited from r8a77951.dtsi.
Fixes: 6e87525d751fac57 ("arm64: dts: renesas: Add Renesas R8A779M8 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/aeb4530f7fbac8329b334dcb169382c836a5f32d.1655458564.git.geert+renesas@glider.be
|
|
While Renesas SoC DT bindings documents started to appear under
Documentation/devicetree/bindings/soc/renesas, these are not yet covered
by the file and directory patterns in the Renesas ARM/ARM64 Architecture
sections.
Add the missing patterns.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f99c03a95a103517418f0b23d3da45e0dd0ffb3b.1655456310.git.geert+renesas@glider.be
|
|
Don't print a misleading header length mismatch error if the i2c call
returns an error. Instead just return the error code without any error
message.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are packets which doesn't have a payload. In that case, the second
i2c_master_read() will have a zero length. But because the NFC
controller doesn't have any data left, it will NACK the I2C read and
-ENXIO will be returned. In case there is no payload, just skip the
second i2c master read.
Fixes: 6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following is now supported:
$ tc qdisc add PORT clsact
$ tc filter add dev PORT egress ...
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, this script sets up the test scenario, which is supposed to end
in an inability of the system to negotiate a link. It then waits for a bit,
and verifies that the system can diagnose why the link was not established.
The wait time for the scenario where different link speeds are forced on
the two ends of a loopback cable, was set to 4 seconds, which exactly
covered it. As of a recent mlxsw firmware update, this time gets longer,
and this test starts failing.
The time that selftests currently wait for links to be established is
currently $WAIT_TIMEOUT, or 20 seconds. It seems reasonable that if this is
the time necessary to establish and bring up a link, it should also be
enough to determine that a link cannot be established and why.
Therefore in this patch, convert the sleeps to busywaits, so that if a
failure is established sooner (as is expected), the test runs quicker. And
use $WAIT_TIMEOUT as the time to wait.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of spelling and language mistakes in the flower section are
fixed. The spacing between the text inside some comments and the comment
symbols are also updated for consistency.
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pagecache handles readpage failing by itself; it doesn't want
filesystems to remove pages from under it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If a buffer is completed with an error, its uptodate flag will be clear,
so the page_uptodate variable will have been set to 0. There's no
need to check PageError here.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
The page cache clears the error bit before calling ->read_folio(),
so this condition could never have been true.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
Just because there has been a read error doesn't mean we should avoid
marking this part of the folio as uptodate. Indeed, it may overwrite
the error part of the folio and let us mark the entire folio uptodate.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
Pages returned from read_mapping_page() are always uptodate, so
this check is unnecessary.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
read_mapping_folio() returns an ERR_PTR if the folio is not
uptodate, so this check is simply dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not
a page with PageError set, or a page that is not Uptodate, so this is
dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this test is not needed.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this test is not needed.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() encounters an error, it returns an errno, not a
page with PageError set, so this is dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If read_mapping_page() sees a page with PageError set, it returns a
PTR_ERR(). Checking PageError again is simply dead code.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
Add information on the use of 'file', whether ->read_folio should be
synchronous, and steer new callers towards calling read_mapping_folio()
instead of calling ->read_folio directly.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
By passing ->read_folio to filemap_read_folio(), we can use
filemap_read_folio() in do_read_cache_folio().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If the call to filler() returns AOP_TRUNCATED_PAGE, we need to
retry the page cache lookup.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
No functionality change intended; this simply moves code around to
disentangle the function a little.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
The 'extern' keyword is not necessary and removing it lets us shorten
some lines.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
All callers of find_get_pages_range(), pagevec_lookup_range() and
pagevec_lookup() have now been removed.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
This is a straightforward conversion.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Change the guts of check_move_unevictable_pages() over to use folios
and add check_move_unevictable_pages() as a wrapper.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Use folios throughout.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Use folios throughout this function. That removes the last caller of
huge_pagevec_release(), so delete that too.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Convert this function to use folios throughout.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Acked-by: Chao Yu <chao@kernel.org>
|
|
The called functions all use pages, so just convert back to a page.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
If the folio is large, it may overlap the beginning or end of the
unused range. If it does, we need to avoid invalidating it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
Use a folio throughout this function.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
This is the equivalent of find_get_pages() but fills a folio_batch
instead of an array of pages.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
|
|
These functions have no more users, so delete them.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
|
|
Remove the last caller of add_to_page_cache()
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
|
|
Pass in a folio from mpage_readahead(). Also convert map_buffer_to_page()
to map_buffer_to_folio(). There's still no support for large folios here;
there are numerous places which depend on the folio being PAGE_SIZE.
The VM_BUG_ON prevents anyone from thinking that it will work.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
This wrapper is no longer used. Remove it and all references to it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
If the last folio in a file is split as a result of truncation,
we simply clear the dirty bits for the pages we're discarding.
That causes NR_FILE_DIRTY (among other counters) to be thrown off
and eventually Linux will hang in balance_dirty_pages_ratelimited()
Reported-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Fixes: d68eccad3706 ("mm/filemap: Allow large folios to be added to the page cache")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
Free sk in case tipc_sk_insert() fails.
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Arun Ramadoss says:
====================
net: dsa: microchip: use ksz_chip_reg for
This patch series tries to use the same approach as struct ksz8 for
register which has different address for different switch family. It
moves the struct ksz8 from ksz8.h to struct ksz_chip_reg. Based on the
switch detect, the corresponding mask, reg and shifts are assigned.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Geert Uytterhoeven
Michael Walle
Maksym Glubokiy
Petr Machata
Walter Heymans
Matthew Wilcox (Oracle)
Hangyu Hua
David S. Miller
Arun Ramadoss