| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The board has a microchip 24aa025e48 eeprom, which is a 2 Kbits memory,
so it's compatible with at24c02 not at24c32.
Also the size property is wrong, it's not 128 bytes, but 256 bytes.
Thus removing and leaving it to the default (256).
Fixes: 1e5f532c27371 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220607090455.80433-1-eugen.hristev@microchip.com
|
|
Use proper compatible strings for SAMA7G5's RTC and RTT IPs. These are
necessary for configuring wakeup sources for ULP1 PM mode.
Fixes: 6501330f9f5e ("ARM: at91: pm: add pm support for SAMA7G5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220523092421.317345-4-claudiu.beznea@microchip.com
|
|
Use proper compatible strings for SAM9X60's RTC and RTT IPs. These are
necessary for configuring wakeup sources for ULP1 PM mode.
Fixes: eaedc0d379da ("ARM: at91: pm: add ULP1 support for SAM9X60")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220523092421.317345-3-claudiu.beznea@microchip.com
|
|
Use proper compatible strings for SAMA5D2's RTC IPs. This is necessary
for configuring wakeup sources for ULP1 PM mode.
Fixes: d7484f5c6b3b ("ARM: at91: pm: configure wakeup sources for ULP1 mode")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220523092421.317345-2-claudiu.beznea@microchip.com
|
|
Commit ceaf69f8eadc ("fanotify: do not allow setting dirent events in
mask of non-dir") added restrictions about setting dirent events in the
mask of a non-dir inode mark, which does not make any sense.
For backward compatibility, these restictions were added only to new
(v5.17+) APIs.
It also does not make any sense to set the flags FAN_EVENT_ON_CHILD or
FAN_ONDIR in the mask of a non-dir inode. Add these flags to the
dir-only restriction of the new APIs as well.
Move the check of the dir-only flags for new APIs into the helper
fanotify_events_supported(), which is only called for FAN_MARK_ADD,
because there is no need to error on an attempt to remove the dir-only
flags from non-dir inode.
Fixes: ceaf69f8eadc ("fanotify: do not allow setting dirent events in mask of non-dir")
Link: https://lore.kernel.org/linux-fsdevel/20220627113224.kr2725conevh53u4@quack3.lan/
Link: https://lore.kernel.org/r/20220627174719.2838175-1-amir73il@gmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Delete the redundant word 'the'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
The mask_ack operation clears the interrupt by writing to the PICSR
register. This we don't want for level triggered interrupt because
it does not actually clear the interrupt on the source hardware.
This was causing issues in qemu with multi core setups where
interrupts would continue to fire even though they had been cleared in
PICSR.
Just remove the mask_ack operation.
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
Fix the below kernel-doc warning by adding the description for return
value.
"warning: No description found for return value of
'zynqmp_pmux_get_function_groups'".
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/1655462819-28801-5-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations. As part of the output-enable configuration, ZynqMP pinctrl
driver takes care of removing the pins from tri-state.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/1655462819-28801-4-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add 'output-enable' configuration parameter to the properties list.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1655462819-28801-3-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add configuration values(enable/disable) for tri-state parameter.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/1655462819-28801-2-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This SoC shall use the mediatek-cpufreq driver, or the system will
crash upon any clock scaling request: add it to the cpufreq-dt-platdev
blocklist.
Fixes: 39b360102f3a ("cpufreq: mediatek: Add support for MT8186")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In pmac_cpufreq_init_MacRISC3(), we need to add corresponding
of_node_put() for the three node pointers whose refcount have
been incremented by of_find_node_by_name().
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Offlining cpu6 and cpu7 and then onlining cpu6 hangs on
sc7180-trogdor-lazor because the throttle interrupt doesn't exist.
Similarly, things go sideways when suspend/resume runs. That's because
the qcom_cpufreq_hw_cpu_online() and qcom_cpufreq_hw_lmh_exit()
functions are calling genirq APIs with an interrupt value of '-6', i.e.
-ENXIO, and that isn't good.
Check the value of the throttle interrupt like we already do in other
functions in this file and bail out early from lmh code to fix the hang.
Reported-by: Rob Clark <robdclark@chromium.org>
Cc: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: a1eb080a0447 ("cpufreq: qcom-hw: provide online/offline operations")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes: 157f527639da ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ]
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
syzbot reproduced the bug ...
BUG: sleeping function called from invalid context at kernel/workqueue.c:3010
... with the following stack trace fragment ...
start_flush_work kernel/workqueue.c:3010 [inline]
__flush_work+0x109/0xb10 kernel/workqueue.c:3074
__cancel_work_timer+0x3f9/0x570 kernel/workqueue.c:3162
sk_psock_stop+0x4cb/0x630 net/core/skmsg.c:802
sock_map_destroy+0x333/0x760 net/core/sock_map.c:1581
inet_csk_destroy_sock+0x196/0x440 net/ipv4/inet_connection_sock.c:1130
__tcp_close+0xd5b/0x12b0 net/ipv4/tcp.c:2897
tcp_close+0x29/0xc0 net/ipv4/tcp.c:2909
... introduced by d8616ee2affc. Do a quick trace of the code path and the
bug is obvious:
inet_csk_destroy_sock(sk)
sk_prot->destroy(sk); <--- sock_map_destroy
sk_psock_stop(, true); <--- true so cancel workqueue
cancel_work_sync() <--- splat, because *_bh_disable()
We can not call cancel_work_sync() from inside destroy path. So mark
the sk_psock_stop call to skip this cancel_work_sync(). This will avoid
the BUG, but means we may run sk_psock_backlog after or during the
destroy op. We zapped the ingress_skb queue in sk_psock_stop (safe to
do with local_bh_disable) so its empty and the sk_psock_backlog work
item will not find any pkts to process here. However, because we are
not going to wait for it or clear its ->state its possible it kicks off
or is already running. This should be 'safe' up until psock drops its
refcnt to psock->sk. The sock_put() that drops this reference is only
done at psock destroy time from sk_psock_destroy(). This is done through
workqueue when sk_psock_drop() is called on psock refnt reaches 0.
And importantly sk_psock_destroy() does a cancel_work_sync(). So trivial
fix works.
I've had hit or miss luck reproducing this caught it once or twice with
the provided reproducer when running with many runners. However, syzkaller
is very good at reproducing so relying on syzkaller to verify fix.
Fixes: d8616ee2affc ("bpf, sockmap: Fix sk->sk_forward_alloc warn_on in sk_stream_kill_queues")
Reported-by: syzbot+140186ceba0c496183bc@syzkaller.appspotmail.com
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/bpf/20220628035803.317876-1-john.fastabend@gmail.com
|
|
Set PINCTRL_OCELOT config option as a tristate and add
MODULE_DEVICE_TABLE()/MODULE_LICENSE() to export appropriate
information. Moreover, switch from builtin_platform_driver()
to module_platform_driver().
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220617103548.490092-1-clement.leger@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
find_energy_efficient_cpu() integrates a margin to protect tasks from
bouncing back and forth from a CPU to another. This margin is set as being
6% of the total current energy estimated on the system. This however does
not work for two reasons:
1. The energy estimation is not a good absolute value:
compute_energy() used in feec() is a good estimation for task placement as
it allows to compare the energy with and without a task. The computed
delta will give a good overview of the cost for a certain task placement.
It, however, doesn't work as an absolute estimation for the total energy
of the system. First it adds the contribution to idle CPUs into the
energy, second it mixes util_avg with util_est values. util_avg contains
the near history for a CPU usage, it doesn't tell at all what the current
utilization is. A system that has been quite busy in the near past will
hold a very high energy and then a high margin preventing any task
migration to a lower capacity CPU, wasting energy. It even creates a
negative feedback loop: by holding the tasks on a less efficient CPU, the
margin contributes in keeping the energy high.
2. The margin handicaps small tasks:
On a system where the workload is composed mostly of small tasks (which is
often the case on Android), the overall energy will be high enough to
create a margin none of those tasks can cross. On a Pixel4, a small
utilization of 5% on all the CPUs creates a global estimated energy of 140
joules, as per the Energy Model declaration of that same device. This
means, after applying the 6% margin that any migration must save more than
8 joules to happen. No task with a utilization lower than 40 would then be
able to migrate away from the biggest CPU of the system.
The 6% of the overall system energy was brought by the following patch:
(eb92692b2544 sched/fair: Speed-up energy-aware wake-ups)
It was previously 6% of the prev_cpu energy. Also, the following one
made this margin value conditional on the clusters where the task fits:
(8d4c97c105ca sched/fair: Only compute base_energy_pd if necessary)
We could simply revert that margin change to what it was, but the original
version didn't have strong grounds neither and as demonstrated in (1.) the
estimated energy isn't a good absolute value. Instead, removing it
completely. It is indeed, made possible by recent changes that improved
energy estimation comparison fairness (sched/fair: Remove task_util from
effective utilization in feec()) (PM: EM: Increase energy calculation
precision) and task utilization stabilization (sched/fair: Decay task
util_avg during migration)
Without a margin, we could have feared bouncing between CPUs. But running
LISA's eas_behaviour test coverage on three different platforms (Hikey960,
RB-5 and DB-845) showed no issue.
Removing the energy margin enables more energy-optimized placements for a
more energy efficient system.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-8-vdonnefort@google.com
|
|
The energy estimation in find_energy_efficient_cpu() (feec()) relies on
the computation of the effective utilization for each CPU of a perf domain
(PD). This effective utilization is then used as an estimation of the busy
time for this pd. The function effective_cpu_util() which gives this value,
scales the utilization relative to IRQ pressure on the CPU to take into
account that the IRQ time is hidden from the task clock. The IRQ scaling is
as follow:
effective_cpu_util = irq + (cpu_cap - irq)/cpu_cap * util
Where util is the sum of CFS/RT/DL utilization, cpu_cap the capacity of
the CPU and irq the IRQ avg time.
If now we take as an example a task placement which doesn't raise the OPP
on the candidate CPU, we can write the energy delta as:
delta = OPPcost/cpu_cap * (effective_cpu_util(cpu_util + task_util) -
effective_cpu_util(cpu_util))
= OPPcost/cpu_cap * (cpu_cap - irq)/cpu_cap * task_util
We end-up with an energy delta depending on the IRQ avg time, which is a
problem: first the time spent on IRQs by a CPU has no effect on the
additional energy that would be consumed by a task. Second, we don't want
to favour a CPU with a higher IRQ avg time value.
Nonetheless, we need to take the IRQ avg time into account. If a task
placement raises the PD's frequency, it will increase the energy cost for
the entire time where the CPU is busy. A solution is to only use
effective_cpu_util() with the CPU contribution part. The task contribution
is added separately and scaled according to prev_cpu's IRQ time.
No change for the FREQUENCY_UTIL component of the energy estimation. We
still want to get the actual frequency that would be selected after the
task placement.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-7-vdonnefort@google.com
|
|
The Perf Domain (PD) cpumask (struct em_perf_domain.cpus) stays
invariant after Energy Model creation, i.e. it is not updated after
CPU hotplug operations.
That's why the PD mask is used in conjunction with the cpu_online_mask
(or Sched Domain cpumask). Thereby the cpu_online_mask is fetched
multiple times (in compute_energy()) during a run-queue selection
for a task.
cpu_online_mask may change during this time which can lead to wrong
energy calculations.
To be able to avoid this, use the select_rq_mask per-cpu cpumask to
create a cpumask out of PD cpumask and cpu_online_mask and pass it
through the function calls of the EAS run-queue selection path.
The PD cpumask for max_spare_cap_cpu/compute_prev_delta selection
(find_energy_efficient_cpu()) is now ANDed not only with the SD mask
but also with the cpu_online_mask. This is fine since this cpumask
has to be in syc with the one used for energy computation
(compute_energy()).
An exclusive cpuset setup with at least one asymmetric CPU capacity
island (hence the additional AND with the SD cpumask) is the obvious
exception here.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-6-vdonnefort@google.com
|
|
On 21/06/2022 11:04, Vincent Donnefort wrote:
> From: Dietmar Eggemann <dietmar.eggemann@arm.com>
https://lkml.kernel.org/r/202206221253.ZVyGQvPX-lkp@intel.com discovered
that this patch doesn't build anymore (on tip sched/core or linux-next)
because of commit f5b2eeb499910 ("sched/fair: Consider CPU affinity when
allowing NUMA imbalance in find_idlest_group()").
New version of [PATCH v11 4/7] sched/fair: Rename select_idle_mask to
select_rq_mask below.
-- >8 --
Decouple the name of the per-cpu cpumask select_idle_mask from its usage
in select_idle_[cpu/capacity]() of the CFS run-queue selection
(select_task_rq_fair()).
This is to support the reuse of this cpumask in the Energy Aware
Scheduling (EAS) path (find_energy_efficient_cpu()) of the CFS run-queue
selection.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/250691c7-0e2b-05ab-bedf-b245c11d9400@arm.com
|
|
effective_cpu_util() already has a `int cpu' parameter which allows to
retrieve the CPU capacity scale factor (or maximum CPU capacity) inside
this function via an arch_scale_cpu_capacity(cpu).
A lot of code calling effective_cpu_util() (or the shim
sched_cpu_util()) needs the maximum CPU capacity, i.e. it will call
arch_scale_cpu_capacity() already.
But not having to pass it into effective_cpu_util() will make the EAS
wake-up code easier, especially when the maximum CPU capacity reduced
by the thermal pressure is passed through the EAS wake-up functions.
Due to the asymmetric CPU capacity support of arm/arm64 architectures,
arch_scale_cpu_capacity(int cpu) is a per-CPU variable read access via
per_cpu(cpu_scale, cpu) on such a system.
On all other architectures it is a a compile-time constant
(SCHED_CAPACITY_SCALE).
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-4-vdonnefort@google.com
|
|
Before being migrated to a new CPU, a task sees its PELT values
synchronized with rq last_update_time. Once done, that same task will also
have its sched_avg last_update_time reset. This means the time between
the migration and the last clock update will not be accounted for in
util_avg and a discontinuity will appear. This issue is amplified by the
PELT clock scaling. It takes currently one tick after the CPU being idle
to let clock_pelt catching up clock_task.
This is especially problematic for asymmetric CPU capacity systems which
need stable util_avg signals for task placement and energy estimation.
Ideally, this problem would be solved by updating the runqueue clocks
before the migration. But that would require taking the runqueue lock
which is quite expensive [1]. Instead estimate the missing time and update
the task util_avg with that value.
To that end, we need sched_clock_cpu() but it is a costly function. Limit
the usage to the case where the source CPU is idle as we know this is when
the clock is having the biggest risk of being outdated.
See comment in migrate_se_pelt_lag() for more details about how the PELT
value is estimated. Notice though this estimation doesn't take into account
IRQ and Paravirt time.
[1] https://lkml.kernel.org/r/20190709115759.10451-1-chris.redpath@arm.com
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-3-vdonnefort@google.com
|
|
Introducing macro helpers u64_u32_{store,load}() to factorize lockless
accesses to u64 variables for 32-bits architectures.
Users are for now cfs_rq.min_vruntime and sched_avg.last_update_time. To
accommodate the later where the copy lies outside of the structure
(cfs_rq.last_udpate_time_copy instead of sched_avg.last_update_time_copy),
use the _copy() version of those helpers.
Those new helpers encapsulate smp_rmb() and smp_wmb() synchronization and
therefore, have a small penalty for 32-bits machines in set_task_rq_fair()
and init_cfs_rq().
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/20220621090414.433602-2-vdonnefort@google.com
|
|
Sometimes we want to know an accurate number of samples even if it's
lost. Currenlty PERF_RECORD_LOST is generated for a ring-buffer which
might be shared with other events. So it's hard to know per-event
lost count.
Add event->lost_samples field and PERF_FORMAT_LOST to retrieve it from
userspace.
Original-patch-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220616180623.1358843-1-namhyung@kernel.org
|
|
[Problem Statement]
select_idle_cpu() might spend too much time searching for an idle CPU,
when the system is overloaded.
The following histogram is the time spent in select_idle_cpu(),
when running 224 instances of netperf on a system with 112 CPUs
per LLC domain:
@usecs:
[0] 533 | |
[1] 5495 | |
[2, 4) 12008 | |
[4, 8) 239252 | |
[8, 16) 4041924 |@@@@@@@@@@@@@@ |
[16, 32) 12357398 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[32, 64) 14820255 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[64, 128) 13047682 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[128, 256) 8235013 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[256, 512) 4507667 |@@@@@@@@@@@@@@@ |
[512, 1K) 2600472 |@@@@@@@@@ |
[1K, 2K) 927912 |@@@ |
[2K, 4K) 218720 | |
[4K, 8K) 98161 | |
[8K, 16K) 37722 | |
[16K, 32K) 6715 | |
[32K, 64K) 477 | |
[64K, 128K) 7 | |
netperf latency usecs:
=======
case load Lat_99th std%
TCP_RR thread-224 257.39 ( 0.21)
The time spent in select_idle_cpu() is visible to netperf and might have a negative
impact.
[Symptom analysis]
The patch [1] from Mel Gorman has been applied to track the efficiency
of select_idle_sibling. Copy the indicators here:
SIS Search Efficiency(se_eff%):
A ratio expressed as a percentage of runqueues scanned versus
idle CPUs found. A 100% efficiency indicates that the target,
prev or recent CPU of a task was idle at wakeup. The lower the
efficiency, the more runqueues were scanned before an idle CPU
was found.
SIS Domain Search Efficiency(dom_eff%):
Similar, except only for the slower SIS
patch.
SIS Fast Success Rate(fast_rate%):
Percentage of SIS that used target, prev or
recent CPUs.
SIS Success rate(success_rate%):
Percentage of scans that found an idle CPU.
The test is based on Aubrey's schedtests tool, including netperf, hackbench,
schbench and tbench.
Test on vanilla kernel:
schedstat_parse.py -f netperf_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
TCP_RR 28 threads 99.978 18.535 99.995 100.000
TCP_RR 56 threads 99.397 5.671 99.964 100.000
TCP_RR 84 threads 21.721 6.818 73.632 100.000
TCP_RR 112 threads 12.500 5.533 59.000 100.000
TCP_RR 140 threads 8.524 4.535 49.020 100.000
TCP_RR 168 threads 6.438 3.945 40.309 99.999
TCP_RR 196 threads 5.397 3.718 32.320 99.982
TCP_RR 224 threads 4.874 3.661 25.775 99.767
UDP_RR 28 threads 99.988 17.704 99.997 100.000
UDP_RR 56 threads 99.528 5.977 99.970 100.000
UDP_RR 84 threads 24.219 6.992 76.479 100.000
UDP_RR 112 threads 13.907 5.706 62.538 100.000
UDP_RR 140 threads 9.408 4.699 52.519 100.000
UDP_RR 168 threads 7.095 4.077 44.352 100.000
UDP_RR 196 threads 5.757 3.775 35.764 99.991
UDP_RR 224 threads 5.124 3.704 28.748 99.860
schedstat_parse.py -f schbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
normal 1 mthread 99.152 6.400 99.941 100.000
normal 2 mthreads 97.844 4.003 99.908 100.000
normal 3 mthreads 96.395 2.118 99.917 99.998
normal 4 mthreads 55.288 1.451 98.615 99.804
normal 5 mthreads 7.004 1.870 45.597 61.036
normal 6 mthreads 3.354 1.346 20.777 34.230
normal 7 mthreads 2.183 1.028 11.257 21.055
normal 8 mthreads 1.653 0.825 7.849 15.549
schedstat_parse.py -f hackbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
process-pipe 1 group 99.991 7.692 99.999 100.000
process-pipe 2 groups 99.934 4.615 99.997 100.000
process-pipe 3 groups 99.597 3.198 99.987 100.000
process-pipe 4 groups 98.378 2.464 99.958 100.000
process-pipe 5 groups 27.474 3.653 89.811 99.800
process-pipe 6 groups 20.201 4.098 82.763 99.570
process-pipe 7 groups 16.423 4.156 77.398 99.316
process-pipe 8 groups 13.165 3.920 72.232 98.828
process-sockets 1 group 99.977 5.882 99.999 100.000
process-sockets 2 groups 99.927 5.505 99.996 100.000
process-sockets 3 groups 99.397 3.250 99.980 100.000
process-sockets 4 groups 79.680 4.258 98.864 99.998
process-sockets 5 groups 7.673 2.503 63.659 92.115
process-sockets 6 groups 4.642 1.584 58.946 88.048
process-sockets 7 groups 3.493 1.379 49.816 81.164
process-sockets 8 groups 3.015 1.407 40.845 75.500
threads-pipe 1 group 99.997 0.000 100.000 100.000
threads-pipe 2 groups 99.894 2.932 99.997 100.000
threads-pipe 3 groups 99.611 4.117 99.983 100.000
threads-pipe 4 groups 97.703 2.624 99.937 100.000
threads-pipe 5 groups 22.919 3.623 87.150 99.764
threads-pipe 6 groups 18.016 4.038 80.491 99.557
threads-pipe 7 groups 14.663 3.991 75.239 99.247
threads-pipe 8 groups 12.242 3.808 70.651 98.644
threads-sockets 1 group 99.990 6.667 99.999 100.000
threads-sockets 2 groups 99.940 5.114 99.997 100.000
threads-sockets 3 groups 99.469 4.115 99.977 100.000
threads-sockets 4 groups 87.528 4.038 99.400 100.000
threads-sockets 5 groups 6.942 2.398 59.244 88.337
threads-sockets 6 groups 4.359 1.954 49.448 87.860
threads-sockets 7 groups 2.845 1.345 41.198 77.102
threads-sockets 8 groups 2.871 1.404 38.512 74.312
schedstat_parse.py -f tbench_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
loopback 28 threads 99.976 18.369 99.995 100.000
loopback 56 threads 99.222 7.799 99.934 100.000
loopback 84 threads 19.723 6.819 70.215 100.000
loopback 112 threads 11.283 5.371 55.371 99.999
loopback 140 threads 0.000 0.000 0.000 0.000
loopback 168 threads 0.000 0.000 0.000 0.000
loopback 196 threads 0.000 0.000 0.000 0.000
loopback 224 threads 0.000 0.000 0.000 0.000
According to the test above, if the system becomes busy, the
SIS Search Efficiency(se_eff%) drops significantly. Although some
benchmarks would finally find an idle CPU(success_rate% = 100%), it is
doubtful whether it is worth it to search the whole LLC domain.
[Proposal]
It would be ideal to have a crystal ball to answer this question:
How many CPUs must a wakeup path walk down, before it can find an idle
CPU? Many potential metrics could be used to predict the number.
One candidate is the sum of util_avg in this LLC domain. The benefit
of choosing util_avg is that it is a metric of accumulated historic
activity, which seems to be smoother than instantaneous metrics
(such as rq->nr_running). Besides, choosing the sum of util_avg
would help predict the load of the LLC domain more precisely, because
SIS_PROP uses one CPU's idle time to estimate the total LLC domain idle
time.
In summary, the lower the util_avg is, the more select_idle_cpu()
should scan for idle CPU, and vice versa. When the sum of util_avg
in this LLC domain hits 85% or above, the scan stops. The reason to
choose 85% as the threshold is that this is the imbalance_pct(117)
when a LLC sched group is overloaded.
Introduce the quadratic function:
y = SCHED_CAPACITY_SCALE - p * x^2
and y'= y / SCHED_CAPACITY_SCALE
x is the ratio of sum_util compared to the CPU capacity:
x = sum_util / (llc_weight * SCHED_CAPACITY_SCALE)
y' is the ratio of CPUs to be scanned in the LLC domain,
and the number of CPUs to scan is calculated by:
nr_scan = llc_weight * y'
Choosing quadratic function is because:
[1] Compared to the linear function, it scans more aggressively when the
sum_util is low.
[2] Compared to the exponential function, it is easier to calculate.
[3] It seems that there is no accurate mapping between the sum of util_avg
and the number of CPUs to be scanned. Use heuristic scan for now.
For a platform with 112 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 112 111 108 102 93 81 65 47 25 1 0 ...
For a platform with 16 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 16 15 15 14 13 11 9 6 3 0 0 ...
Furthermore, to minimize the overhead of calculating the metrics in
select_idle_cpu(), borrow the statistics from periodic load balance.
As mentioned by Abel, on a platform with 112 CPUs per LLC, the
sum_util calculated by periodic load balance after 112 ms would
decay to about 0.5 * 0.5 * 0.5 * 0.7 = 8.75%, thus bringing a delay
in reflecting the latest utilization. But it is a trade-off.
Checking the util_avg in newidle load balance would be more frequent,
but it brings overhead - multiple CPUs write/read the per-LLC shared
variable and introduces cache contention. Tim also mentioned that,
it is allowed to be non-optimal in terms of scheduling for the
short-term variations, but if there is a long-term trend in the load
behavior, the scheduler can adjust for that.
When SIS_UTIL is enabled, the select_idle_cpu() uses the nr_scan
calculated by SIS_UTIL instead of the one from SIS_PROP. As Peter and
Mel suggested, SIS_UTIL should be enabled by default.
This patch is based on the util_avg, which is very sensitive to the
CPU frequency invariance. There is an issue that, when the max frequency
has been clamp, the util_avg would decay insanely fast when
the CPU is idle. Commit addca285120b ("cpufreq: intel_pstate: Handle no_turbo
in frequency invariance") could be used to mitigate this symptom, by adjusting
the arch_max_freq_ratio when turbo is disabled. But this issue is still
not thoroughly fixed, because the current code is unaware of the user-specified
max CPU frequency.
[Test result]
netperf and tbench were launched with 25% 50% 75% 100% 125% 150%
175% 200% of CPU number respectively. Hackbench and schbench were launched
by 1, 2 ,4, 8 groups. Each test lasts for 100 seconds and repeats 3 times.
The following is the benchmark result comparison between
baseline:vanilla v5.19-rc1 and compare:patched kernel. Positive compare%
indicates better performance.
Each netperf test is a:
netperf -4 -H 127.0.1 -t TCP/UDP_RR -c -C -l 100
netperf.throughput
=======
case load baseline(std%) compare%( std%)
TCP_RR 28 threads 1.00 ( 0.34) -0.16 ( 0.40)
TCP_RR 56 threads 1.00 ( 0.19) -0.02 ( 0.20)
TCP_RR 84 threads 1.00 ( 0.39) -0.47 ( 0.40)
TCP_RR 112 threads 1.00 ( 0.21) -0.66 ( 0.22)
TCP_RR 140 threads 1.00 ( 0.19) -0.69 ( 0.19)
TCP_RR 168 threads 1.00 ( 0.18) -0.48 ( 0.18)
TCP_RR 196 threads 1.00 ( 0.16) +194.70 ( 16.43)
TCP_RR 224 threads 1.00 ( 0.16) +197.30 ( 7.85)
UDP_RR 28 threads 1.00 ( 0.37) +0.35 ( 0.33)
UDP_RR 56 threads 1.00 ( 11.18) -0.32 ( 0.21)
UDP_RR 84 threads 1.00 ( 1.46) -0.98 ( 0.32)
UDP_RR 112 threads 1.00 ( 28.85) -2.48 ( 19.61)
UDP_RR 140 threads 1.00 ( 0.70) -0.71 ( 14.04)
UDP_RR 168 threads 1.00 ( 14.33) -0.26 ( 11.16)
UDP_RR 196 threads 1.00 ( 12.92) +186.92 ( 20.93)
UDP_RR 224 threads 1.00 ( 11.74) +196.79 ( 18.62)
Take the 224 threads as an example, the SIS search metrics changes are
illustrated below:
vanilla patched
4544492 +237.5% 15338634 sched_debug.cpu.sis_domain_search.avg
38539 +39686.8% 15333634 sched_debug.cpu.sis_failed.avg
128300000 -87.9% 15551326 sched_debug.cpu.sis_scanned.avg
5842896 +162.7% 15347978 sched_debug.cpu.sis_search.avg
There is -87.9% less CPU scans after patched, which indicates lower overhead.
Besides, with this patch applied, there is -13% less rq lock contention
in perf-profile.calltrace.cycles-pp._raw_spin_lock.raw_spin_rq_lock_nested
.try_to_wake_up.default_wake_function.woken_wake_function.
This might help explain the performance improvement - Because this patch allows
the waking task to remain on the previous CPU, rather than grabbing other CPUs'
lock.
Each hackbench test is a:
hackbench -g $job --process/threads --pipe/sockets -l 1000000 -s 100
hackbench.throughput
=========
case load baseline(std%) compare%( std%)
process-pipe 1 group 1.00 ( 1.29) +0.57 ( 0.47)
process-pipe 2 groups 1.00 ( 0.27) +0.77 ( 0.81)
process-pipe 4 groups 1.00 ( 0.26) +1.17 ( 0.02)
process-pipe 8 groups 1.00 ( 0.15) -4.79 ( 0.02)
process-sockets 1 group 1.00 ( 0.63) -0.92 ( 0.13)
process-sockets 2 groups 1.00 ( 0.03) -0.83 ( 0.14)
process-sockets 4 groups 1.00 ( 0.40) +5.20 ( 0.26)
process-sockets 8 groups 1.00 ( 0.04) +3.52 ( 0.03)
threads-pipe 1 group 1.00 ( 1.28) +0.07 ( 0.14)
threads-pipe 2 groups 1.00 ( 0.22) -0.49 ( 0.74)
threads-pipe 4 groups 1.00 ( 0.05) +1.88 ( 0.13)
threads-pipe 8 groups 1.00 ( 0.09) -4.90 ( 0.06)
threads-sockets 1 group 1.00 ( 0.25) -0.70 ( 0.53)
threads-sockets 2 groups 1.00 ( 0.10) -0.63 ( 0.26)
threads-sockets 4 groups 1.00 ( 0.19) +11.92 ( 0.24)
threads-sockets 8 groups 1.00 ( 0.08) +4.31 ( 0.11)
Each tbench test is a:
tbench -t 100 $job 127.0.0.1
tbench.throughput
======
case load baseline(std%) compare%( std%)
loopback 28 threads 1.00 ( 0.06) -0.14 ( 0.09)
loopback 56 threads 1.00 ( 0.03) -0.04 ( 0.17)
loopback 84 threads 1.00 ( 0.05) +0.36 ( 0.13)
loopback 112 threads 1.00 ( 0.03) +0.51 ( 0.03)
loopback 140 threads 1.00 ( 0.02) -1.67 ( 0.19)
loopback 168 threads 1.00 ( 0.38) +1.27 ( 0.27)
loopback 196 threads 1.00 ( 0.11) +1.34 ( 0.17)
loopback 224 threads 1.00 ( 0.11) +1.67 ( 0.22)
Each schbench test is a:
schbench -m $job -t 28 -r 100 -s 30000 -c 30000
schbench.latency_90%_us
========
case load baseline(std%) compare%( std%)
normal 1 mthread 1.00 ( 31.22) -7.36 ( 20.25)*
normal 2 mthreads 1.00 ( 2.45) -0.48 ( 1.79)
normal 4 mthreads 1.00 ( 1.69) +0.45 ( 0.64)
normal 8 mthreads 1.00 ( 5.47) +9.81 ( 14.28)
*Consider the Standard Deviation, this -7.36% regression might not be valid.
Also, a OLTP workload with a commercial RDBMS has been tested, and there
is no significant change.
There were concerns that unbalanced tasks among CPUs would cause problems.
For example, suppose the LLC domain is composed of 8 CPUs, and 7 tasks are
bound to CPU0~CPU6, while CPU7 is idle:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
util_avg 1024 1024 1024 1024 1024 1024 1024 0
Since the util_avg ratio is 87.5%( = 7/8 ), which is higher than 85%,
select_idle_cpu() will not scan, thus CPU7 is undetected during scan.
But according to Mel, it is unlikely the CPU7 will be idle all the time
because CPU7 could pull some tasks via CPU_NEWLY_IDLE.
lkp(kernel test robot) has reported a regression on stress-ng.sock on a
very busy system. According to the sched_debug statistics, it might be caused
by SIS_UTIL terminates the scan and chooses a previous CPU earlier, and this
might introduce more context switch, especially involuntary preemption, which
impacts a busy stress-ng. This regression has shown that, not all benchmarks
in every scenario benefit from idle CPU scan limit, and it needs further
investigation.
Besides, there is slight regression in hackbench's 16 groups case when the
LLC domain has 16 CPUs. Prateek mentioned that we should scan aggressively
in an LLC domain with 16 CPUs. Because the cost to search for an idle one
among 16 CPUs is negligible. The current patch aims to propose a generic
solution and only considers the util_avg. Something like the below could
be applied on top of the current patch to fulfill the requirement:
if (llc_weight <= 16)
nr_scan = nr_scan * 32 / llc_weight;
For LLC domain with 16 CPUs, the nr_scan will be expanded to 2 times large.
The smaller the CPU number this LLC domain has, the larger nr_scan will be
expanded. This needs further investigation.
There is also ongoing work[2] from Abel to filter out the busy CPUs during
wakeup, to further speed up the idle CPU scan. And it could be a following-up
optimization on top of this change.
Suggested-by: Tim Chen <tim.c.chen@intel.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Tested-by: Mohini Narkhede <mohini.narkhede@intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20220612163428.849378-1-yu.c.chen@intel.com
|
|
sched_setattr(2) issues via kernel/sched/core.c:__sched_setscheduler()
a CAP_SYS_NICE audit event unconditionally, even when the requested
operation does not require that capability / is unprivileged, i.e. for
reducing niceness.
This is relevant in connection with SELinux, where a capability check
results in a policy decision and by default a denial message on
insufficient permission is issued.
It can lead to three undesired cases:
1. A denial message is generated, even in case the operation was an
unprivileged one and thus the syscall succeeded, creating noise.
2. To avoid the noise from 1. the policy writer adds a rule to ignore
those denial messages, hiding future syscalls, where the task
performs an actual privileged operation, leading to hidden limited
functionality of that task.
3. To avoid the noise from 1. the policy writer adds a rule to allow
the task the capability CAP_SYS_NICE, while it does not need it,
violating the principle of least privilege.
Conduct privilged/unprivileged categorization first and perform a
capable test (and at most once) only if needed.
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220615152505.310488-1-cgzones@googlemail.com
|
|
As of commit afe06efdf07c ("sched: Extend scheduler's asym packing")
group_first_cpu() became an unused function, remove it.
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Link: https://lore.kernel.org/r/20220617181151.29980-3-zhangqiao22@huawei.com
|
|
" *" is redundant. so remove it.
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220617181151.29980-2-zhangqiao22@huawei.com
|
|
When checking for libc rseq support in the library constructor, don't
only depend on the symbols presence, check that the registration was
completed.
This targets a scenario where the libc has rseq support but it is not
wired for the current architecture in 'bits/rseq.h', we want to fallback
to our internal registration mechanism.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/r/20220614154830.1367382-4-mjeanson@efficios.com
|
|
This header is also used in librseq where it can be included in C++
code, add a space between literals and string macros.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/r/20220614154830.1367382-3-mjeanson@efficios.com
|
|
Make the RISC-V rseq selftests compatible with glibc-2.35 by using the
rseq_get_abi() helper.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/r/20220614154830.1367382-2-mjeanson@efficios.com
|
|
Replace apprpriately with appropriately.
Fixes: 1e4d84c6589e9 ("drm/doc: Polish plane composition property docs")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Simon Ser <contact@emersion.fr>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628003407.77765-1-marex@denx.de
|
|
The convention for indentation seems to be a single tab. Help text is
further indented by an additional two whitespaces. Fix the lines that
violate these rules.
While at it, remove an extra tab.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Message-Id: <20220523063040.10991-1-juergh@canonical.com>
[tony@atomide.com: updated for extra tab]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When routes corresponding to addresses are restored by
fixup_permanent_addr(), the dst_nopolicy parameter was not set.
The typical use case is a user that configures an address on a down
interface and then put this interface up.
Let's take care of this flag in addrconf_f6i_alloc(), so that every callers
benefit ont it.
CC: stable@kernel.org
CC: David Forster <dforster@brocade.com>
Fixes: df789fe75206 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Reported-by: Siwar Zitouni <siwar.zitouni@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220623120015.32640-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'vlan_bitmap' is a bitmap and is used as such. So allocate it with
devm_bitmap_zalloc() and its explicit bit size (i.e. VLAN_N_VID).
This avoids the need of the VLAN_BITMAP_SIZE macro which:
- needlessly has a 'nic_dev' parameter
- should be "long" (and not byte) aligned, so that the bitmap semantic
is respected
This is in fact not an issue because VLAN_N_VID is 4096 at the time
being, but devm_bitmap_zalloc() is less verbose and easier to understand.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/6ff7b7d21414240794a77dc2456914412718a145.1656260842.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1e037794f7f0 ("ARM: OMAP3+: PRM: register interrupt information from DT")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Simon Horman says:
====================
nfp: add VEPA and adapter selftest support
1. Support for ethtool -t: adapter selftest
2. VEPA mode in HW bridge.
This supplements existing support for VEB mode.
====================
Link: https://lore.kernel.org/r/20220624073816.1272984-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for ethtool selftest.
e.g.
# ethtool -t DEVNAME
test result like:
The test result is PASS
The test extra info:
Link Test 0
NSP Test 0
Firmware Test 0
Register Test 0
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for VEPA mode of HW bridge.
The default remains VEB mode.
The mode may be configured using ndo_bridge_setlink,
and inspected using ndo_bridge_getlink.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete the redundant word 'the'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220625071558.3852-1-yuanjilin@cdjrlc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete the redundant word 'use'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220625070633.64982-1-yuanjilin@cdjrlc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete the redundant word 'the'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220625065745.61464-1-yuanjilin@cdjrlc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We should respect link partner capabilities and not force flow control
support on every link. Even more, in current state the MAC driver do not
advertises pause support so we should not keep flow control enabled at
all.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.
On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".
With this patch we will notify usbnet about link status change provided by the
PHYlib.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mails to Charles get an auto reply, that he is no longer working at
Eff'Innov technologies. Drop the entry and mark the driver as orphaned.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220626200039.4062784-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In pdata_quirks_init_clocks(), the loop contains
of_find_node_by_name() but without corresponding of_node_put().
Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220618020603.4055792-1-windhl@126.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This should be bitwise operator not logical.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Shreenidhi Shedi <sshedi@vmware.com>
Link: https://lore.kernel.org/r/20220626132947.3992423-1-sshedi@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Delete duplicate words of "the".
Signed-off-by: Deming Wang <wangdeming@inspur.com>
Link: https://lore.kernel.org/r/20220624013114.1913-1-wangdeming@inspur.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Victor Nogueira says:
====================
Notify user space if any actions were flushed before error
This patch series fixes the behaviour of actions flush so that the
kernel always notifies user space whenever it deletes actions during a
flush operation, even if it didn't flush all the actions. This series
also introduces tdc tests to verify this new behaviour.
====================
Link: https://lore.kernel.org/r/20220623140742.684043-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Eugen Hristev
Claudiu Beznea
Amir Goldstein
Xiang wangx
Stafford Horne
Sai Krishna Potthuri
AngeloGioacchino Del Regno
Liang He
Stephen Boyd
John Fastabend
Clément Léger
Vincent Donnefort
Dietmar Eggemann
Namhyung Kim
Chen Yu
Christian Göttsche
Zhang Qiao
Michael Jeanson
Marek Vasut
Juerg Haefliger
Nicolas Dichtel
Christophe JAILLET
Miaoqian Lin
Jakub Kicinski
Fei Qin
Yinjun Zhang
Jilin Yuan
Oleksij Rempel
Michael Walle
Shreenidhi Shedi
Deming Wang