aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/networking/ethtool-netlink.rst (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-10-03ethtool: add interface to interact with Ethernet Power EquipmentOleksij Rempel1-0/+59
Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-23net: phy: Add support for rate matchingSean Anderson1-0/+2
This adds support for rate matching (also known as rate adaptation) to the phy subsystem. The general idea is that the phy interface runs at one speed, and the MAC throttles the rate at which it sends packets to the link speed. There's a good overview of several techniques for achieving this at [1]. This patch adds support for three: pause-frame based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and 2BASE-TL), and open-loop-based (such as in 10GBASE-W). This patch makes a few assumptions and a few non assumptions about the types of rate matching available. First, it assumes that different phys may use different forms of rate matching. Second, it assumes that phys can use rate matching for any of their supported link speeds (e.g. if a phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T). Third, it does not assume that all interface modes will use the same form of rate matching. Fourth, it does not assume that all phy devices will support rate matching (even if some do). Relaxing or strengthening these (non-)assumptions could result in a different API. For example, if all interface modes were assumed to use the same form of rate matching, then a bitmask of interface modes supportting rate matching would suffice. For some better visibility into the process, the current rate matching mode is exposed as part of the ethtool ksettings. For the moment, only read access is supported. I'm not sure what userspace might want to configure yet (disable it altogether, disable just one mode, specify the mode to use, etc.). For the moment, since only pause-based rate adaptation support is added in the next few commits, rate matching can be disabled altogether by adjusting the advertisement. 802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and "rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls this feature "rate adaptation". I chose "rate matching" because it is shorter, and because Russell doesn't think "adaptation" is correct in this context. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-15net: ethtool: extend ringparam set/get APIs for tx_pushJie Wang1-0/+8
Currently tx push is a standard driver feature which controls use of a fast path descriptor push. So this patch extends the ringparam APIs and data structures to support set/get tx push by ethtool -G/g. Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-23ethtool: add support to set/get completion queue event sizeSubbaraya Sundeep1-0/+11
Add support to set completion queue event size via ethtool -G parameter and get it via ethtool -g parameter. ~ # ./ethtool -G eth0 cqe-size 512 ~ # ./ethtool -g eth0 Ring parameters for eth0: Pre-set maximums: RX: 1048576 RX Mini: n/a RX Jumbo: n/a TX: 1048576 Current hardware settings: RX: 256 RX Mini: n/a RX Jumbo: n/a TX: 4096 RX Buf Len: 2048 CQE Size: 128 Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-28ethtool: add header/data split indicationJakub Kicinski1-0/+8
For applications running on a mix of platforms it's useful to have a clear indication whether host's NIC supports the geometry requirements of TCP zero-copy. TCP zero-copy Rx requires data to be neatly placed into memory pages. Most NICs can't do that. This patch is adding GET support only, since the NICs I work with either always have the feature enabled or enable it whenever MTU is set to jumbo. In other words I don't need SET. But adding set should be trivial. (The only note on SET is that we will likely want the setting to be "sticky" and use 0 / `unknown` to reset it back to driver default.) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get rx buf len via ethtoolHao Chen1-4/+6
Add support to set rx buf len via ethtool -G parameter and get rx buf len via ethtool -g parameter. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-06ethtool: Add transceiver module extended stateIdo Schimmel1-0/+10
Add an extended state and sub-state to describe link issues related to transceiver modules. The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state tells user space that port is unable to gain a carrier because the CMIS Module State Machine did not reach the ModuleReady (Fully Operational) state. For example, if the module is stuck at ModuleLowPwr or ModuleFault state. In case of the latter, user space can read the fault reason from the module's EEPROM and potentially reset it. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-06ethtool: Add ability to control transceiver modules' power modeIdo Schimmel1-2/+69
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver modules parameters and retrieve their status. The first parameter to control is the power mode of the module. It is only relevant for paged memory modules, as flat memory modules always operate in low power mode. When a paged memory module is in low power mode, its power consumption is reduced to the minimum, the management interface towards the host is available and the data path is deactivated. User space can choose to put modules that are not currently in use in low power mode and transition them to high power mode before putting the associated ports administratively up. This is useful for user space that favors reduced power consumption and lower temperatures over reduced link up times. In QSFP-DD modules the transition from low power mode to high power mode can take a few seconds and this transition is only expected to get longer with future / more complex modules. User space can control the power mode of the module via the power mode policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible values: * high: Module is always in high power mode. * auto: Module is transitioned by the host to high power mode when the first port using it is put administratively up and to low power mode when the last port using it is put administratively down. The operational power mode of the module is available to user space via the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not reported to user space when a module is not plugged-in. The user API is designed to be generic enough so that it could be used for modules with different memory maps (e.g., SFF-8636, CMIS). The only implementation of the device driver API in this series is for a MAC driver (mlxsw) where the module is controlled by the device's firmware, but it is designed to be generic enough so that it could also be used by implementations where the module is controlled by the CPU. CMIS testing ============ # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off The module is not in low power mode, as it is not forced by hardware (LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off). The power mode can be queried from the kernel. In case LowPwrAllowRequestHW was on, the kernel would need to take into account the state of the LowPwrRequestHW signal, which is not visible to user space. $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp11 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp11 up Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp11 down Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On SFF-8636 testing ================ # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm The module is not in low power mode, as it is not forced by hardware (Power override is on) or by software (Power set is off). The power mode can be queried from the kernel. In case Power override was off, the kernel would need to take into account the state of the LPMode signal, which is not visible to user space. $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp13 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp13 up Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp13 down Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-24ethtool: add two coalesce attributes for CQE modeYufeng Mo1-0/+15
Currently, there are many drivers who support CQE mode configuration, some configure it as a fixed when initialized, some provide an interface to change it by ethtool private flags. In order to make it more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and 'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these parameters can be accessed by ethtool netlink coalesce uAPI. Also add an new structure kernel_ethtool_coalesce, then the new parameter can be added into this struct. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-16docs: ethtool: Add two link extended substates of bad signal integrityGuangbin Huang1-0/+8
Add documentation for two bad signal integrity substates: ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS. Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-07-01ethtool: add a new command for getting PHC virtual clocksYangbo Lu1-0/+22
Add an interface for getting PHC (PTP Hardware Clock) virtual clocks, which are based on PHC physical clock providing hardware timestamp to network packets. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Document behavior when module EEPROM bank attribute is omittedIdo Schimmel1-0/+2
The kernel assumes bank 0 when 'ETHTOOL_MSG_MODULE_EEPROM_GET' is sent without 'ETHTOOL_A_MODULE_EEPROM_BANK'. Document it as part of the interface documentation. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Document correct attribute typeIdo Schimmel1-1/+1
'ETHTOOL_A_MODULE_EEPROM_DATA' is a binary attribute, not a nested one. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Use correct command name in titleIdo Schimmel1-2/+2
The command is called 'ETHTOOL_MSG_MODULE_EEPROM_GET', not 'ETHTOOL_MSG_MODULE_EEPROM'. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-19ethtool: add missing EEPROM to list of messagesJakub Kicinski1-34/+36
ETHTOOL_MSG_MODULE_EEPROM_GET is missing from the list of messages. ETHTOOL_MSG_MODULE_EEPROM_GET_REPLY is sadly a rather long name so we need to adjust column length. v2: use spaces (Andrew) Fixes: c781ff12a2f3 ("ethtool: Allow network drivers to dump arbitrary EEPROM data") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-16docs: ethtool: document standard statisticsJakub Kicinski1-0/+82
Add documentation for ETHTOOL_MSG_STATS_GET. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-15ethtool: add FEC statisticsJakub Kicinski1-0/+21
Similarly to pause statistics add stats for FEC. The IEEE standard mandates two sets of counters: - 30.5.1.1.17 aFECCorrectedBlocks - 30.5.1.1.18 aFECUncorrectableBlocks where block is a block of bits FEC operates on. Each of these counters is defined per lane (PCS instance). Multiple vendors provide number of corrected _bits_ rather than/as well as blocks. This set adds the 2 standard-based block counters and a extra one for corrected bits. Counters are exposed to user space via netlink in new attributes. Each attribute carries an array of u64s, first element is the total count, and the following ones are a per-lane break down. Much like with pause stats the operation will not fail when driver does not implement the get_fec_stats callback (nor can the driver fail the operation by returning an error). If stats can't be reported the relevant attributes will be empty. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-11ethtool: Allow network drivers to dump arbitrary EEPROM dataVladyslav Tarasiuk1-2/+34
Define get_module_eeprom_by_page() ethtool callback and implement netlink infrastructure. get_module_eeprom_by_page() allows network drivers to dump a part of module's EEPROM specified by page and bank numbers along with offset and length. It is effectively a netlink replacement for get_module_info() and get_module_eeprom() pair, which is needed due to emergence of complex non-linear EEPROM layouts. Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-5/+5
Conflicts: MAINTAINERS - keep Chandrasekar drivers/net/ethernet/mellanox/mlx5/core/en_main.c - simple fix + trust the code re-added to param.c in -next is fine include/linux/bpf.h - trivial include/linux/ethtool.h - trivial, fix kdoc while at it include/linux/skmsg.h - move to relevant place in tcp.c, comment re-wrapped net/core/skmsg.c - add the sk = sk // sk = NULL around calls net/tipc/crypto.c - trivial Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-04-06docs: ethtool: correct quotesJakub Kicinski1-2/+2
Quotes to backticks. All commands use backticks since the names are constants. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-06docs: ethtool: fix some copy-paste errorsJakub Kicinski1-5/+5
Fix incorrect documentation. Mostly referring to other objects, likely because the text was copied and not adjusted. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-31ethtool: support FEC settings over netlinkJakub Kicinski1-2/+60
Add FEC API to netlink. This is not a 1-to-1 conversion. FEC settings already depend on link modes to tell user which modes are supported. Take this further an use link modes for manual configuration. Old struct ethtool_fecparam is still used to talk to the drivers, so we need to translate back and forth. We can revisit the internal API if number of FEC encodings starts to grow. Enforce only one active FEC bit (by using a bit position rather than another mask). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-03ethtool: Extend link modes settings uAPI with lanesDanielle Ratson1-5/+6
Currently, when auto negotiation is on, the user can advertise all the linkmodes which correspond to a specific speed, but does not have a similar selector for the number of lanes. This is significant when a specific speed can be achieved using different number of lanes. For example, 2x50 or 4x25. Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct ethtool_link_settings' with lanes field in order to implement a new lanes-selector that will enable the user to advertise a specific number of lanes as well. When auto negotiation is off, lanes parameter can be forced only if the driver supports it. Add a capability bit in 'struct ethtool_ops' that allows ethtool know if the driver can handle the lanes parameter when auto negotiation is off, so if it does not, an error message will be returned when trying to set lanes. Example: $ ethtool -s swp1 lanes 4 $ ethtool swp1 Settings for swp1: Supported ports: [ FIBRE ] Supported link modes: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full 40000baseSR4/Full 40000baseLR4/Full 25000baseCR/Full 25000baseSR/Full 50000baseCR2/Full 100000baseSR4/Full 100000baseCR4/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 40000baseCR4/Full 40000baseSR4/Full 40000baseLR4/Full 100000baseSR4/Full 100000baseCR4/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Auto-negotiation: on Port: Direct Attach Copper PHYAD: 0 Transceiver: internal Link detected: no Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-0/+3
Two minor conflicts: 1) net/ipv4/route.c, adding a new local variable while moving another local variable and removing it's initial assignment. 2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes. One pretty prints the port mode differently, whilst another changes the driver to try and obtain the port mode from the port node rather than the switch node. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-17ethtool: add and use message type for tunnel info replyMichal Kubecek1-0/+3
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd field in genetlink header) for replies to tunnel info netlink request, i.e. the same value as the request have. This is a problem because we are using two separate enums for userspace to kernel and kernel to userspace message types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for kernel to userspace messages. As the tunnel info request reached mainline in 5.9 merge window, we should still be able to fix the reply message type without breaking backward compatibility. Fixes: c7d759eb7b12 ("ethtool: add tunnel info interface") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-15ethtool: add standard pause statsJakub Kicinski1-0/+11
Currently drivers have to report their pause frames statistics via ethtool -S, and there is a wide variety of names used for these statistics. Add the two statistics defined in IEEE 802.3x to the standard API. Create a new ethtool request header flag for including statistics in the response to GET commands. Always create the ETHTOOL_A_PAUSE_STATS nest in replies when flag is set. Testing if driver declares the op is not a reliable way of checking if any stats will actually be included and therefore we don't want to give the impression that presence of ETHTOOL_A_PAUSE_STATS indicates driver support. Note that this patch does not include PFC counters, which may fit better in dcbnl? But mostly I don't need them/have a setup to test them so I haven't looked deeply into exposing them :) v3: - add a helper for "uninitializing" stats, rather than a cryptic memset() (Andrew) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03udp_tunnel: add the ability to hard-code IANA VXLANJakub Kicinski1-0/+3
mlx5 has the IANA VXLAN port (4789) hard coded by the device, instead of being added dynamically when tunnels are created. To support this add a workaround flag to struct udp_tunnel_nic_info. Skipping updates for the port is fairly trivial, dumping the hard coded port via ethtool requires some code duplication. The port is not a part of any real table, we dump it in a special table which has no tunnel types supported and only one entry. This is the last known workaround / hack needed to convert all drivers to the new infra. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-07-10ethtool: add tunnel info interfaceJakub Kicinski1-0/+33
Add an interface to report offloaded UDP ports via ethtool netlink. Now that core takes care of tracking which UDP tunnel ports the NICs are aware of we can quite easily export this information out to user space. The responsibility of writing the netlink dumps is split between ethtool code and udp_tunnel_nic.c - since udp_tunnel module may not always be loaded, yet we should always report the capabilities of the NIC. $ ethtool --show-tunnels eth0 Tunnel information for eth0: UDP port table 0: Size: 4 Types: vxlan No entries UDP port table 1: Size: 4 Types: geneve, vxlan-gpe Entries (1): port 1230, vxlan-gpe v4: - back to v2, build fix is now directly in udp_tunnel.h v3: - don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET not set. v2: - fix string set count, - reorder enums in the uAPI, - fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset in docs and comments. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-07Documentation: networking: fix ethtool-netlink table formatsRandy Dunlap1-9/+9
Fix table formatting to eliminate warnings. Documentation/networking/ethtool-netlink.rst:509: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:522: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:543: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:555: WARNING: Malformed table. Documentation/networking/ethtool-netlink.rst:591: WARNING: Malformed table. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-29Documentation: networking: ethtool-netlink: Add link extended stateAmit Cohen1-4/+124
Add link extended state attributes. Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-10docs: networking: fix extra spaces in ethtool-netlinkJakub Kicinski1-6/+6
Sphinx appears to get upset at extra spaces at the end of a literal: Documentation/networking/ethtool-netlink.rst:1032: WARNING: Inline literal start-string without end-string. Documentation/networking/ethtool-netlink.rst:1034: WARNING: Inline literal start-string without end-string. Documentation/networking/ethtool-netlink.rst:1036: WARNING: Inline literal start-string without end-string. Documentation/networking/ethtool-netlink.rst:1089: WARNING: Inline literal start-string without end-string. Documentation/networking/ethtool-netlink.rst:1091: WARNING: Inline literal start-string without end-string. Documentation/networking/ethtool-netlink.rst:1093: WARNING: Inline literal start-string without end-string. Fixes: f2bc8ad31a7f ("net: ethtool: Allow PHY cable test TDR data to configured") Fixes: a331172b156b ("net: ethtool: Add attributes for cable test TDR data") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-26net: ethtool: Allow PHY cable test TDR data to configuredAndrew Lunn1-3/+19
Allow the user to configure where on the cable the TDR data should be retrieved, in terms of first and last sample, and the step between samples. Also add the ability to ask for TDR data for just one pair. If this configuration is not provided, it defaults to 1-150m at 1m intervals for all pairs. Signed-off-by: Andrew Lunn <andrew@lunn.ch> v3: Move the TDR configuration into a structure Add a range check on step Use NL_SET_ERR_MSG_ATTR() when appropriate Move TDR configuration into a nest Document attributes in the request Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-26net: ethtool: Add attributes for cable test TDR dataAndrew Lunn1-0/+81
Some Ethernet PHYs can return the raw time domain reflectromatry data. Add the attributes to allow this data to be requested and returned via netlink ethtool. Signed-off-by: Andrew Lunn <andrew@lunn.ch> v2: m -> cm Report what the PHY actually used for start/stop/step. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-21ethtool: provide UAPI for PHY Signal Quality Index (SQI)Oleksij Rempel1-2/+4
Signal Quality Index is a mandatory value required by "OPEN Alliance SIG" for the 100Base-T1 PHYs [1]. This indicator can be used for cable integrity diagnostic and investigating other noise sources and implement by at least two vendors: NXP[2] and TI[3]. [1] http://www.opensig.org/download/document/218/Advanced_PHY_features_for_automotive_Ethernet_V1.0.pdf [2] https://www.nxp.com/docs/en/data-sheet/TJA1100.pdf [3] https://www.ti.com/product/DP83TC811R-Q1 Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-10net: ethtool: Add attributes for cable test reportsAndrew Lunn1-0/+41
Add the attributes needed to report cable test results to userspace. The reports are expected to be per twisted pair. A nested property per pair can report the result of the cable test. A nested property can also report the length of the cable to any fault. v2: Grammar fixes Change length from u16 to u32 s/DEV/HEADER/g Add status attributes Rename pairs from numbers to letters. v3: Fixed example in document Add ETHTOOL_A_CABLE_NEST_* enum Add ETHTOOL_MSG_CABLE_TEST_NTF to documentation Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-10net: ethtool: netlink: Add support for triggering a cable testAndrew Lunn1-1/+15
Add new ethtool netlink calls to trigger the starting of a PHY cable test. Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when ETHTOOL_NETLINK is builtin, which would result in kernel linking errors. v2: Remove unwanted white space change Remove ethnl_cable_test_act_ops and use doit handler Rename cable_test_set_policy cable_test_act_policy Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY v3: Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation Remove unused cable_test_get_policy Add Reviewed-by tags v4: Remove unwanted blank line Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-06ethtool: provide UAPI for PHY master/slave configuration.Oleksij Rempel1-16/+19
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space. The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018: 22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32) The MASTER-SLAVE role affects the clock configuration: ------------------------------------------------------------------------------- When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER. iMX6Q KSZ9031 XXX ------\ /-----------\ /------------\ | | | | | MAC |<----RGMII----->| PHY Slave |<------>| PHY Master | |<--- 125 MHz ---+-<------/ | | \ | ------/ \-----------/ \------------/ ^ \-TX_TCLK ------------------------------------------------------------------------------- Since some clock or link related issues are only reproducible in a specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial to provide generic (not 100BASE-T1 specific) interface to the user space for configuration flexibility and trouble shooting. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: provide timestamping information with TSINFO_GET requestMichal Kubecek1-1/+29
Implement TSINFO_GET request to get timestamping information for a network device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl request. Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink code use the same logic to get timestamping information from the device. v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: add EEE_NTF notificationMichal Kubecek1-0/+1
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network device are modified using ETHTOOL_MSG_EEE_SET netlink message or ETHTOOL_SEEE ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: set EEE settings with EEE_SET requestMichal Kubecek1-1/+24
Implement EEE_SET netlink request to set EEE settings of a network device. These are traditionally set with ETHTOOL_SEEE ioctl request. The netlink interface allows setting the EEE status for all link modes supported by kernel but only first 32 link modes can be set at the moment as only those are supported by the ethtool_ops callback. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: provide EEE settings with EEE_GET requestMichal Kubecek1-1/+33
Implement EEE_GET request to get EEE settings of a network device. These are traditionally available via ETHTOOL_GEEE ioctl request. The netlink interface allows reporting EEE status for all link modes supported by kernel but only first 32 link modes are provided at the moment as only those are reported by the ethtool_ops callback and drivers. v2: fix alignment (whitespace only) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: add PAUSE_NTF notificationMichal Kubecek1-0/+1
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message or ETHTOOL_SPAUSEPARAM ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: set pause parameters with PAUSE_SET requestMichal Kubecek1-1/+2
Implement PAUSE_SET netlink request to set pause parameters of a network device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: provide pause parameters with PAUSE_GET requestMichal Kubecek1-1/+39
Implement PAUSE_GET request to get pause parameters of a network device. These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: add COALESCE_NTF notificationMichal Kubecek1-0/+1
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink message or ETHTOOL_SCOALESCE ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: set coalescing parameters with COALESCE_SET requestMichal Kubecek1-1/+41
Implement COALESCE_SET netlink request to set coalescing parameters of a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl request. This commit adds only support for device coalescing parameters, not per queue coalescing parameters. Like the ioctl implementation, the generic ethtool code checks if only supported parameters are modified; if not, first offending attribute is reported using extack. v2: fix alignment (whitespace only) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-29ethtool: provide coalescing parameters with COALESCE_GET requestMichal Kubecek1-1/+47
Implement COALESCE_GET request to get coalescing parameters of a network device. These are traditionally available via ETHTOOL_GCOALESCE ioctl request. This commit adds only support for device coalescing parameters, not per queue coalescing parameters. Omit attributes with zero values unless they are declared as supported (i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is set). Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12ethtool: add CHANNELS_NTF notificationMichal Kubecek1-0/+1
Send ETHTOOL_MSG_CHANNELS_NTF notification whenever channel counts of a network device are modified using ETHTOOL_MSG_CHANNELS_SET netlink message or ETHTOOL_SCHANNELS ioctl request. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12ethtool: set device channel counts with CHANNELS_SET requestMichal Kubecek1-1/+22
Implement CHANNELS_SET netlink request to set channel counts of a network device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request. Like the ioctl implementation, the generic ethtool code checks if supplied values do not exceed driver defined limits; if they do, first offending attribute is reported using extack. Checks preventing removing channels used for RX indirection table or zerocopy AF_XDP socket are also implemented. Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be used by both ioctl and netlink code. v2: - fix netdev reference leak in error path (found by Jakub Kicinsky) Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-12ethtool: provide channel counts with CHANNELS_GET requestMichal Kubecek1-1/+29
Implement CHANNELS_GET request to get channel counts of a network device. These are traditionally available via ETHTOOL_GCHANNELS ioctl request. Omit attributes for channel types which are not supported by driver or device (zero reported for maximum). v2: (all suggested by Jakub Kicinski) - minor cleanup in channels_prepare_data() - more descriptive channels_reply_size() - omit attributes with zero max count Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.