| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* 'features/imx3' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
Conflicts:
arch/arm/mach-imx/mm-imx3.c
|
|
It was observed on a mx31pdk board that audio playback only worked when the bootloader was Redboot, and
did not work when U-boot was used.
Comparing the sources of these bootloaders showed that the AIPS registers were not setup in U-boot.
Instead of relying on the bootloader to setup the AIPS registers, do it in the kernel so that audio
playback can work independantly of the bootloader being used.
Copied the AIPS settings from Redboot to the kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The LPM field of register CCMR is used to select the mode that the processor will run
when it goes to WFI.
When mx31 enters in WFI mode the LPM field is at its reset value of 0,
which configures the mx31 to enter in "wait mode".
On mx35, the LPM field on mx35 is also at 0 after reset, which corresponds
to "run mode" instead of "wait mode".
Instead of relying on the reset value of LPM to set the low power mode for
WFI, configure mx31 and mx35 to run in "wait mode"
Reported-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
|
|
arm-soc fixes for 3.3-rc:
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-imx/mach-mx53_ard.c: add missing iounmap
ARM: imx: iomux-v1.h: Fix build error due to __init annotation
ARM: at91: Fix at91sam9g45 and at91cap9 reset
ARM: at91: make rstc soc independent
ARM: at91: introduce AT91_SAM9_ALT_RESET to select the at91sam9 alternative reset
ARM: at91: merge at91cap9_ddrsdr.h in at91sam9_ddrsdr.h
ARM: at91: fix cap9 ddrsdr register
ARM/USB: at91/ohci-at91: rename vbus_pin_inverted to vbus_pin_active_low
USB: at91: fix clk_get error handling
ARM: at91: removal of CAP9 SoC family
ARM: at91: fix at91rm9200 soc subtype handling
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
ARM: imx6: add missing twd_clk for imx6q clock
|
|
Fix the following build error found when building imx_v4_v5_defconfig:
CC arch/arm/mach-imx/mach-imx27ipcam.o
In file included from arch/arm/plat-mxc/include/mach/iomux-mx27.h:23,
from arch/arm/mach-imx/mach-imx27ipcam.c:22:
arch/arm/plat-mxc/include/mach/iomux-v1.h:99: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'imx_iomuxv1_init'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Consolidate i.MX 5 platforms to be under the new shared i.MX 3/5/6 tree.
* tag 'arm-soc-imx-move' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM i.MX: Update defconfig
ARM i.MX: Merge i.MX5 support into mach-imx
ARM i.MX5: remove unnecessary includes from board files
Fix up fairly trivial conflicts due to various changes nearby in
arch/arm/{mach,plat}-imx/{Kconfig,Makefile}
Pull request had been sent to the wrong email address, but happened
before the merge window closed. I'm merging the MX 5 consolidation,
since it apparently will help the next development window and will avoid
conflicts later as per Arnd.
|
|
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
ARM: mach-shmobile: specify CHCLR registers on SH7372
dma: shdma: fix runtime PM: clear channel buffers on reset
dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
dmaengine/ste_dma40: clear LNK on channel startup
dmaengine: intel_mid_dma: remove legacy pm interface
ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
dmaengine: intel_mid_dma: error path fix
dmaengine: intel_mid_dma: locking and freeing fixes
mtd: gpmi-nand: move to dma_transfer_direction
mtd: fix compile error for gpmi-nand
mmc: mxs-mmc: fix the dma_transfer_direction migration
dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
dma: mxs-dma: fix a typo in comment
DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
video i.MX IPU: Fix display connections
i.MX IPU DMA: Fix wrong burstsize settings
dmaengine/ste_dma40: allow fixed physical channel
...
Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}
The conflicts looked pretty trivial, but I'll ask people to verify them.
|
|
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
|
|
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/mach-exynos/cpu.c
The changes to arch/arm/mach-exynos/cpu.c were moved to
mach-exynos/common.c.
|
|
Conflicts:
arch/arm/kernel/setup.c
arch/arm/mach-shmobile/board-kota2.c
|
|
The restart support was missed from the initial imx6q submission.
The mxc_restart() does not work for imx6q. Instead, this patch adds
the restart for imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/kernel/setup.c
|
|
* imx/board: (4 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
Updated to v3.2-rc6, conflicts:
arch/arm/kernel/setup.c
|
|
* imx6/pm:
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
|
|
Conflicts:
arch/arm/kernel/setup.c
arch/arm/mach-shmobile/board-kota2.c
|
|
This adds necessary defines for the CSPI3 module (activated with
imx25_add_spi_imx2()) to work on the CSI pins (alternative mode 7).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Two problems exist in the current i.MX5 pm suspend/resume and idle
functions. The first is the current i.MX5 suspend routine will call
tzic_enable_wake(1) to set wake source, this will set all enabled
irq as wake source rather than those wake capable. The second
is i.MX5 idle will call mx5_cpu_lp_set() to prepare enter low power
mode, but it forgets to call wfi instruction to enter this mode.
To fix these two problems, using generic irq chip pm interface and
modify function imx5_idle().
[Tested by Shawn Guo on imx51 babbage board.
Tested by Hui Wang on imx51 pdk board.]
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
|
|
Making CACHE_L2X0 depend on (huge list of MACH_ and ARCH_ configs)
is bothersome to maintain and likely to lead to merge conflicts.
This patch moves the knowledge of which platforms have a L2x0 or
PL310 cache controller to the individual machines. To enable this,
a new MIGHT_HAVE_CACHE_L2X0 config option is introduced to allow
machines to indicate that they may have such a cache controller
independently of each other.
Boards/SoCs which cannot reliably operate without the L2 cache
controller support will need to select CACHE_L2X0 directly from
their own Kconfigs instead. This applies to some TrustZone-enabled
boards where Linux runs in the Normal World, for example.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
(for cns3xxx)
Acked-by: Tony Lindgren <tony@atomide.com>
(for omap)
Acked-by: Shawn Guo <shawn.guo@linaro.org>
(for imx)
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
(for exynos)
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
(for imx)
Acked-by: Olof Johansson <olof@lixom.net>
(for tegra)
|
|
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
WARNING: arch/arm/plat-mxc/built-in.o(.data+0x488): Section mismatch in reference from the variable mxc_driver to the function .init.text:mxc_cpufreq_init()
The variable mxc_driver references
the function __init mxc_cpufreq_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
According to imx pwm RM, the real period value should be
PERIOD value in PWMPR plus 2.
PWMO (Hz) = PCLK(Hz) / (period +2)
Signed-off-by: Jason Chen <jason.chen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@kernel.org
|
|
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
CC arch/arm/plat-mxc/cpufreq.o
arch/arm/plat-mxc/cpufreq.c:203: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:203: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:203: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-mxc/cpufreq.c:203: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:204: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:204: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:204: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-mxc/cpufreq.c:204: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:205: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:205: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:205: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-mxc/cpufreq.c:205: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-mxc/cpufreq.o] Error 1
make: *** [arch/arm/plat-mxc] Error 2
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Jason Chen <jason.chen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@kernel.org
|
|
The IPU internally works on 32bit colors. It can arbitrarily map
between pixel formats and internal representation and also between
internal representation and the physical connection to the display.
The driver used to change the mapping between internal representation
and display connection depending on the user selected bpp which is
wrong. Instead, the mapping is specified by the hardware, so an
additional field in platform data is added to describe the connection
between i.MX and the display. The default for this field is RGB666
which seems to be the only configuration which works without this
patch, so I assumed that all in Kernel boards are connected this
way.
This patch has been tested on a RGB666 connected display and a
RGB888 connected display in both 16bpp and 32bpp modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
|
|
Conflicts:
arch/arm/common/gic.c
arch/arm/plat-omap/include/plat/common.h
|
|
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
|
|
|
|
Conflicts:
arch/arm/mach-imx/mm-imx3.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The arch_ioremap function on i.MX is now an indirect function pointer.
In order to use it from any loadable module, the pointer itself
has to be exported.
ERROR: "imx_ioremap" [drivers/video/tmiofb.ko] undefined!
ERROR: "imx_ioremap" [drivers/usb/host/sl811-hcd.ko] undefined!
ERROR: "imx_ioremap" [drivers/usb/host/r8a66597-hcd.ko] undefined!
ERROR: "imx_ioremap" [drivers/usb/host/oxu210hp-hcd.ko] undefined!
ERROR: "imx_ioremap" [drivers/usb/gadget/r8a66597-udc.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
|
|
We only need to set the system up for a soft-restart if we're going to
be doing a soft-restart. Provide a new function (soft_restart()) which
does the setup and final call for this, and make platforms use it.
Eliminate the call to setup_restart() from the default handler.
This means that platforms arch_reset() function is no longer called with
the page tables prepared for a soft-restart, and caches will still be
enabled.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Krzysztof Ha■asa <khc@pm.waw.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
map_io is the only place to call iotable_init.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
[shawn.guo: rename imx_clock_map_io() to imx6q_clock_map_io()]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx
and adjusts the Makefile/Kconfig entries in a way that it's possible
to compile i.MX5 together with i.MX3/6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
|
|
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
|
|
Convert the SMP imx platforms to use the global gic_handle_irq()
function instead a private function.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Before introducing a global gic_handle_irq(), rename
MXC's version to mxc_gic_handle_irq(). This function will be
removed altogether in a later patch.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
|
|
The AUTO_ZRELADDR selection for ARCH_IMX_V4_V5 and ARCH_MX5 should
really be mutually exclusive to ZBOOT_ROM just like what ARCH_IMX_V6_V7
does.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The patch removes imx_idle hook and use pm_idle instead to get imx
arch_idle prepared for the cleanup. It's suggested by Russel King
as below.
> The final removal of mach/system.h depends on getting rid of the arch_idle
> thing. While going through these headers, I was dismayed to find these:
>
> arch/arm/mach-s3c2410/include/mach/system.h:void (*s3c24xx_idle)(void);
> arch/arm/plat-mxc/include/mach/system.h:extern void (*imx_idle)(void);
>
> when we have a perfectly good pm_idle hook already in place - so there's
> no excuse for these especially when other platforms are already using
> pm_idle to hook their platform specific idle function into. This is
> something that better be gone at the next merge window!
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Since commit (167a19d2: ARM: imx: Introduce generic function for displaying silicon revision)
we no longer need the chip revision strings, so remove them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The patch "ARM: gic: consolidate PPI handling" removes the usage
of test_for_ltirq. After the merge of imx6q remove this there, too.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
|
Arnd Bergmann
Fabio Estevam
Olof Johansson
Linus Torvalds
Nicolas Pitre
Russell King
Shawn Guo
Paul Fertser
Eric Miao
Hui Wang
Dave Martin
Eric Bénard
Richard Zhao
Jason Chen
Marc Zyngier
Richard Zhao
Sascha Hauer
Fabio Estevam
Dirk Behme