| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace a magic 64-bit mask with a list of valid registers, computing
the same mask in the end.
Suggested-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm-unit-tests were adjusted to match bare metal behavior, but KVM
itself was not doing what bare metal does; fix that.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
According to section "Checks on Host Segment and Descriptor-Table
Registers" in Intel SDM vol 3C, the following checks are performed on
vmentry of nested guests:
- In the selector field for each of CS, SS, DS, ES, FS, GS and TR, the
RPL (bits 1:0) and the TI flag (bit 2) must be 0.
- The selector fields for CS and TR cannot be 0000H.
- The selector field for SS cannot be 0000H if the "host address-space
size" VM-exit control is 0.
- On processors that support Intel 64 architecture, the base-address
fields for FS, GS and TR must contain canonical addresses.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM does not have 100% coverage of VMX consistency checks, i.e. some
checks that cause VM-Fail may only be detected by hardware during a
nested VM-Entry. In such a case, KVM must restore L1's state to the
pre-VM-Enter state as L2's state has already been loaded into KVM's
software model.
L1's CR3 and PDPTRs in particular are loaded from vmcs01.GUEST_*. But
when EPT is disabled, the associated fields hold KVM's shadow values,
not L1's "real" values. Fortunately, when EPT is disabled the PDPTRs
come from memory, i.e. are not cached in the VMCS. Which leaves CR3
as the sole anomaly.
A previously applied workaround to handle CR3 was to force nested early
checks if EPT is disabled:
commit 2b27924bb1d48 ("KVM: nVMX: always use early vmcs check when EPT
is disabled")
Forcing nested early checks is undesirable as doing so adds hundreds of
cycles to every nested VM-Entry. Rather than take this performance hit,
handle CR3 by overwriting vmcs01.GUEST_CR3 with L1's CR3 during nested
VM-Entry when EPT is disabled *and* nested early checks are disabled.
By stuffing vmcs01.GUEST_CR3, nested_vmx_restore_host_state() will
naturally restore the correct vcpu->arch.cr3 from vmcs01.GUEST_CR3.
These shenanigans work because nested_vmx_restore_host_state() does a
full kvm_mmu_reset_context(), i.e. unloads the current MMU, which
guarantees vmcs01.GUEST_CR3 will be rewritten with a new shadow CR3
prior to re-entering L1.
vcpu->arch.root_mmu.root_hpa is set to INVALID_PAGE via:
nested_vmx_restore_host_state() ->
kvm_mmu_reset_context() ->
kvm_mmu_unload() ->
kvm_mmu_free_roots()
kvm_mmu_unload() has WARN_ON(root_hpa != INVALID_PAGE), i.e. we can bank
on 'root_hpa == INVALID_PAGE' unless the implementation of
kvm_mmu_reset_context() is changed.
On the way into L1, VMCS.GUEST_CR3 is guaranteed to be written (on a
successful entry) via:
vcpu_enter_guest() ->
kvm_mmu_reload() ->
kvm_mmu_load() ->
kvm_mmu_load_cr3() ->
vmx_set_cr3()
Stuff vmcs01.GUEST_CR3 if and only if nested early checks are disabled
as a "late" VM-Fail should never happen win that case (KVM WARNs), and
the conditional write avoids the need to restore the correct GUEST_CR3
when nested_vmx_check_vmentry_hw() fails.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20190607185534.24368-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These are useful in debugging shadow paging.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Note that in such a case it is quite likely that KVM will BUG_ON
in __pte_list_remove when the VM is closed. However, there is no
immediate risk of memory corruption in the host so a WARN_ON is
enough and it lets you gather traces for debugging.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
After the previous patch, the low bits of the gfn are masked in
both FNAME(fetch) and __direct_map, so we do not need to clear them
in transparent_hugepage_adjust.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These two functions are basically doing the same thing through
kvm_mmu_get_page, link_shadow_page and mmu_set_spte; yet, for historical
reasons, their code looks very different. This patch tries to take the
best of each and make them very similar, so that it is easy to understand
changes that apply to both of them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Release the page at the call-site where it was originally acquired.
This makes the exit code cleaner for most call sites, since they
do not need to duplicate code between success and the failure
label.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The has_leaf_count member was originally added for KVM's paravirtualization
CPUID leaves. However, since then the leaf count _has_ been added to those
leaves as well, so we can drop that special case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
do_cpuid_1_ent does not do the entire processing for a CPUID entry, it
only retrieves the host's values. Rename it to match reality.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
do_cpuid_1_ent is typically called in two places by __do_cpuid_func
for CPUID functions that have subleafs. Both places have to set
the KVM_CPUID_FLAG_SIGNIFCANT_INDEX. Set that flag, and
KVM_CPUID_FLAG_STATEFUL_FUNC as well, directly in do_cpuid_1_ent.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
CPUID function 7 has multiple subleafs. Instead of having nested
switch statements, move the logic to filter supported features to
a separate function, and call it for each subleaf.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rename it as well as __do_cpuid_ent and __do_cpuid_ent_emulated to have
"func" in its name, and drop the index parameter which is always 0.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
perf/core has an earlier version of the x86/cpu tree merged, to avoid
conflicts, and due to this we want to pick up this ABI impacting
revert as well:
049331f277fe: ("x86/fsgsbase: Revert FSGSBASE support")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull tracing fixes from Steven Rostedt:
"This includes three fixes:
- Fix a deadlock from a previous fix to keep module loading and
function tracing text modifications from stepping on each other
(this has a few patches to help document the issue in comments)
- Fix a crash when the snapshot buffer gets out of sync with the main
ring buffer
- Fix a memory leak when reading the memory logs"
* tag 'trace-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Anotate text_mutex split between ftrace_arch_code_modify_post_process() and ftrace_arch_code_modify_prepare()
tracing/snapshot: Resize spare buffer if size changed
tracing: Fix memory leak in tracing_err_log_open()
ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()
ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()
|
|
ARCH_WANT_HUGE_PMD_SHARE config was declared in both architectures:
move this declaration in arch/Kconfig and make those architectures
select it.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> # for arm64
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-07-03
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix the interpreter to properly handle BPF_ALU32 | BPF_ARSH
on BE architectures, from Jiong.
2) Fix several bugs in the x32 BPF JIT for handling shifts by 0,
from Luke and Xi.
3) Fix NULL pointer deref in btf_type_is_resolve_source_only(),
from Stanislav.
4) Properly handle the check that forwarding is enabled on the device
in bpf_ipv6_fib_lookup() helper code, from Anton.
5) Fix UAPI bpf_prog_info fields alignment for archs that have 16 bit
alignment such as m68k, from Baruch.
6) Fix kernel hanging in unregister_netdevice loop while unregistering
device bound to XDP socket, from Ilya.
7) Properly terminate tail update in xskq_produce_flush_desc(), from Nathan.
8) Fix broken always_inline handling in test_lwt_seg6local, from Jiri.
9) Fix bpftool to use correct argument in cgroup errors, from Jakub.
10) Fix detaching dummy prog in XDP redirect sample code, from Prashant.
11) Add Jonathan to AF_XDP reviewers, from Björn.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FSGSBASE series turned out to have serious bugs and there is still an
open issue which is not fully understood yet.
The confidence in those changes has become close to zero especially as the
test cases which have been shipped with that series were obviously never
run before sending the final series out to LKML.
./fsgsbase_64 >/dev/null
Segmentation fault
As the merge window is close, the only sane decision is to revert FSGSBASE
support. The revert is necessary as this branch has been merged into
perf/core already and rebasing all of that a few days before the merge
window is not the most brilliant idea.
I could definitely slap myself for not noticing the test case fail when
merging that series, but TBH my expectations weren't that low back
then. Won't happen again.
Revert the following commits:
539bca535dec ("x86/entry/64: Fix and clean up paranoid_exit")
2c7b5ac5d5a9 ("Documentation/x86/64: Add documentation for GS/FS addressing mode")
f987c955c745 ("x86/elf: Enumerate kernel FSGSBASE capability in AT_HWCAP2")
2032f1f96ee0 ("x86/cpu: Enable FSGSBASE on 64bit by default and add a chicken bit")
5bf0cab60ee2 ("x86/entry/64: Document GSBASE handling in the paranoid path")
708078f65721 ("x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit")
79e1932fa3ce ("x86/entry/64: Introduce the FIND_PERCPU_BASE macro")
1d07316b1363 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
f60a83df4593 ("x86/process/64: Use FSGSBASE instructions on thread copy and ptrace")
1ab5f3f7fe3d ("x86/process/64: Use FSBSBASE in switch_to() if available")
a86b4625138d ("x86/fsgsbase/64: Enable FSGSBASE instructions in helper functions")
8b71340d702e ("x86/fsgsbase/64: Add intrinsics for FSGSBASE instructions")
b64ed19b93c3 ("x86/cpu: Add 'unsafe_fsgsbase' to enable CR4.FSGSBASE")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Chang S. Bae <chang.seok.bae@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
|
|
The trailing newlines will lead to extra newlines in the trace file
which looks like the following output, so remove it.
qemu-system-x86-15695 [002] ...1 15774.839240: kvm_hv_timer_state: vcpu_id 0 hv_timer 1
qemu-system-x86-15695 [002] ...1 15774.839309: kvm_hv_timer_state: vcpu_id 0 hv_timer 1
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Allow testing code for old processors that lack the next RIP save
feature, by disabling usage of the next_rip field.
Nested hypervisors however get the feature unconditionally.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The current x32 BPF JIT does not correctly compile shift operations when
the immediate shift amount is 0. The expected behavior is for this to
be a no-op.
The following program demonstrates the bug. The expexceted result is 1,
but the current JITed code returns 2.
r0 = 1
r1 = 1
r1 <<= 0
if r1 == 1 goto end
r0 = 2
end:
exit
This patch simplifies the code and fixes the bug.
Fixes: 03f5781be2c7 ("bpf, x86_32: add eBPF JIT compiler for ia32")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The current x32 BPF JIT for shift operations is not correct when the
shift amount in a register is 0. The expected behavior is a no-op, whereas
the current implementation changes bits in the destination register.
The following example demonstrates the bug. The expected result of this
program is 1, but the current JITed code returns 2.
r0 = 1
r1 = 1
r2 = 0
r1 <<= r2
if r1 == 1 goto end
r0 = 2
end:
exit
The bug is caused by an incorrect assumption by the JIT that a shift by
32 clear the register. On x32 however, shifts use the lower 5 bits of
the source, making a shift by 32 equivalent to a shift by 0.
This patch fixes the bug using double-precision shifts, which also
simplifies the code.
Fixes: 03f5781be2c7 ("bpf, x86_32: add eBPF JIT compiler for ia32")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Continue consolidating Hyper-V clock and timer code into an ISA
independent Hyper-V clocksource driver.
Move the existing clocksource code under drivers/hv and arch/x86 to the new
clocksource driver while separating out the ISA dependencies. Update
Hyper-V initialization to call initialization and cleanup routines since
the Hyper-V synthetic clock is not independently enumerated in ACPI.
Update Hyper-V clocksource users in KVM and VDSO to get definitions from
the new include file.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-3-git-send-email-mikelley@microsoft.com
|
|
Hyper-V clock/timer code and data structures are currently mixed
in with other code in the ISA independent drivers/hv directory as
well as the ISA dependent Hyper-V code under arch/x86.
Consolidate this code and data structures into a Hyper-V clocksource driver
to better follow the Linux model. In doing so, separate out the ISA
dependent portions so the new clocksource driver works for x86 and for the
in-process Hyper-V on ARM64 code.
To start, move the existing clockevents code to create the new clocksource
driver. Update the VMbus driver to call initialization and cleanup routines
since the Hyper-V synthetic timers are not independently enumerated in
ACPI.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-2-git-send-email-mikelley@microsoft.com
|
|
so the hyper-v clocksource update can be applied.
|
|
Quite some time ago the interrupt entry stubs for unused vectors in the
system vector range got removed and directly mapped to the spurious
interrupt vector entry point.
Sounds reasonable, but it's subtly broken. The spurious interrupt vector
entry point pushes vector number 0xFF on the stack which makes the whole
logic in __smp_spurious_interrupt() pointless.
As a consequence any spurious interrupt which comes from a vector != 0xFF
is treated as a real spurious interrupt (vector 0xFF) and not
acknowledged. That subsequently stalls all interrupt vectors of equal and
lower priority, which brings the system to a grinding halt.
This can happen because even on 64-bit the system vector space is not
guaranteed to be fully populated. A full compile time handling of the
unused vectors is not possible because quite some of them are conditonally
populated at runtime.
Bring the entry stubs back, which wastes 160 bytes if all stubs are unused,
but gains the proper handling back. There is no point to selectively spare
some of the stubs which are known at compile time as the required code in
the IDT management would be way larger and convoluted.
Do not route the spurious entries through common_interrupt and do_IRQ() as
the original code did. Route it to smp_spurious_interrupt() which evaluates
the vector number and acts accordingly now that the real vector numbers are
handed in.
Fixup the pr_warn so the actual spurious vector (0xff) is clearly
distiguished from the other vectors and also note for the vectored case
whether it was pending in the ISR or not.
"Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen."
"Spurious interrupt vector 0xed on CPU#1. Acked."
"Spurious interrupt vector 0xee on CPU#1. Not pending!."
Fixes: 2414e021ac8d ("x86: Avoid building unused IRQ entry stubs")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jan Beulich <jbeulich@suse.com>
Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.de
|
|
Since the rework of the vector management, warnings about spurious
interrupts have been reported. Robert provided some more information and
did an initial analysis. The following situation leads to these warnings:
CPU 0 CPU 1 IO_APIC
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
clear_vector()
do_IRQ()
-> vector is clear
Before the rework the vector entries of legacy interrupts were statically
assigned and occupied precious vector space while most of them were
unused. Due to that the above situation was handled silently because the
vector was handled and the core handler of the assigned interrupt
descriptor noticed that it is shut down and returned.
While this has been usually observed with legacy interrupts, this situation
is not limited to them. Any other interrupt source, e.g. MSI, can cause the
same issue.
After adding proper synchronization for level triggered interrupts, this
can only happen for edge triggered interrupts where the IO-APIC obviously
cannot provide information about interrupts in flight.
While the spurious warning is actually harmless in this case it worries
users and driver developers.
Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead
of VECTOR_UNUSED when the vector is freed up.
If that above late handling happens the spurious detector will not complain
and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on
that line will trigger the spurious warning as before.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>-
Tested-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.459647741@linutronix.de
|
|
When an interrupt is shut down in free_irq() there might be an inflight
interrupt pending in the IO-APIC remote IRR which is not yet serviced. That
means the interrupt has been sent to the target CPUs local APIC, but the
target CPU is in a state which delays the servicing.
So free_irq() would proceed to free resources and to clear the vector
because synchronize_hardirq() does not see an interrupt handler in
progress.
That can trigger a spurious interrupt warning, which is harmless and just
confuses users, but it also can leave the remote IRR in a stale state
because once the handler is invoked the interrupt resources might be freed
already and therefore acknowledgement is not possible anymore.
Implement the irq_get_irqchip_state() callback for the IO-APIC irq chip. The
callback is invoked from free_irq() via __synchronize_hardirq(). Check the
remote IRR bit of the interrupt and return 'in flight' if it is set and the
interrupt is configured in level mode. For edge mode the remote IRR has no
meaning.
As this is only meaningful for level triggered interrupts this won't cure
the potential spurious interrupt warning for edge triggered interrupts, but
the edge trigger case does not result in stale hardware state. This has to
be addressed at the vector/interrupt entry level seperately.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.370295517@linutronix.de
|
|
ftrace_arch_code_modify_prepare() is acquiring text_mutex, while the
corresponding release is happening in ftrace_arch_code_modify_post_process().
This has already been documented in the code, but let's also make the fact
that this is intentional clear to the semantic analysis tools such as sparse.
Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1906292321170.27227@cbobk.fhfr.pm
Fixes: 39611265edc1a ("ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()")
Fixes: d5b844a2cf507 ("ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Add a flags field to struct dev_pagemap to replace the altmap_valid
boolean to be a little more extensible. Also add a pgmap_altmap() helper
to find the optional altmap and clean up the code using the altmap using
it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Thomas reported that:
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rong Chen <rong.a.chen@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently KVM_STATE_NESTED_EVMCS is used to signal that eVMCS
capability is enabled on vCPU.
As indicated by vmx->nested.enlightened_vmcs_enabled.
This is quite bizarre as userspace VMM should make sure to expose
same vCPU with same CPUID values in both source and destination.
In case vCPU is exposed with eVMCS support on CPUID, it is also
expected to enable KVM_CAP_HYPERV_ENLIGHTENED_VMCS capability.
Therefore, KVM_STATE_NESTED_EVMCS is redundant.
KVM_STATE_NESTED_EVMCS is currently used on restore path
(vmx_set_nested_state()) only to enable eVMCS capability in KVM
and to signal need_vmcs12_sync such that on next VMEntry to guest
nested_sync_from_vmcs12() will be called to sync vmcs12 content
into eVMCS in guest memory.
However, because restore nested-state is rare enough, we could
have just modified vmx_set_nested_state() to always signal
need_vmcs12_sync.
From all the above, it seems that we could have just removed
the usage of KVM_STATE_NESTED_EVMCS. However, in order to preserve
backwards migration compatibility, we cannot do that.
(vmx_get_nested_state() needs to signal flag when migrating from
new kernel to old kernel).
Returning KVM_STATE_NESTED_EVMCS when just vCPU have eVMCS enabled
have a bad side-effect of userspace VMM having to send nested-state
from source to destination as part of migration stream. Even if
guest have never used eVMCS as it doesn't even run a nested
hypervisor workload. This requires destination userspace VMM and
KVM to support setting nested-state. Which make it more difficult
to migrate from new host to older host.
To avoid this, change KVM_STATE_NESTED_EVMCS to signal eVMCS is
not only enabled but also active. i.e. Guest have made some
eVMCS active via an enlightened VMEntry. i.e. vmcs12 is copied
from eVMCS and therefore should be restored into eVMCS resident
in memory (by copy_vmcs12_to_enlightened()).
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As comment in code specifies, SMM temporarily disables VMX so we cannot
be in guest mode, nor can VMLAUNCH/VMRESUME be pending.
However, code currently assumes that these are the only flags that can be
set on kvm_state->flags. This is not true as KVM_STATE_NESTED_EVMCS
can also be set on this field to signal that eVMCS should be enabled.
Therefore, fix code to check for guest-mode and pending VMLAUNCH/VMRESUME
explicitly.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This warning can be triggered easily by userspace, so it should certainly not
cause a panic if panic_on_warn is set.
Reported-by: syzbot+c03f30b4f4c46bdf8575@syzkaller.appspotmail.com
Suggested-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This bit is purely advisory. Passing it through to the guest indicates
that the virtual processor, like the physical processor, prefers that
STIBP is only set once during boot and not changed.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When L0 is executing handle_invept(), the TDP MMU is active. Emulating
an L1 INVEPT does require synchronizing the appropriate shadow EPT
root(s), but a call to kvm_mmu_sync_roots in this context won't do
that. Similarly, the hardware TLB and paging-structure-cache entries
associated with the appropriate shadow EPT root(s) must be flushed,
but requesting a TLB_FLUSH from this context won't do that either.
How did this ever work? KVM always does a sync_roots and TLB flush (in
the correct context) when transitioning from L1 to L2. That isn't the
best choice for nested VM performance, but it effectively papers over
the mistakes here.
Remove the unnecessary operations and leave a comment to try to do
better in the future.
Reported-by: Junaid Shahid <junaids@google.com>
Fixes: bfd0a56b90005f ("nEPT: Nested INVEPT")
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Nadav Har'El <nyh@il.ibm.com>
Cc: Jun Nakajima <jun.nakajima@intel.com>
Cc: Xinhao Xu <xinhao.xu@intel.com>
Cc: Yang Zhang <yang.z.zhang@Intel.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by Peter Shier <pshier@google.com>
Reviewed-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Expose PV_SCHED_YIELD feature bit to guest, the guest can check this
feature bit before using paravirtualized sched yield.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The target vCPUs are in runnable state after vcpu_kick and suitable
as a yield target. This patch implements the sched yield hypercall.
17% performance increasement of ebizzy benchmark can be observed in an
over-subscribe environment. (w/ kvm-pv-tlb disabled, testing TLB flush
call-function IPI-many since call-function is not easy to be trigged
by userspace workload).
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When sending a call-function IPI-many to vCPUs, yield if any of
the IPI target vCPUs was preempted, we just select the first
preempted target vCPU which we found since the state of target
vCPUs can change underneath and to avoid race conditions.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When Enlightened VMCS is in use, it is valid to do VMCLEAR and,
according to TLFS, this should "transition an enlightened VMCS from the
active to the non-active state". It is, however, wrong to assume that
it is only valid to do VMCLEAR for the eVMCS which is currently active
on the vCPU performing VMCLEAR.
Currently, the logic in handle_vmclear() is broken: in case, there is no
active eVMCS on the vCPU doing VMCLEAR we treat the argument as a 'normal'
VMCS and kvm_vcpu_write_guest() to the 'launch_state' field irreversibly
corrupts the memory area.
So, in case the VMCLEAR argument is not the current active eVMCS on the
vCPU, how can we know if the area it is pointing to is a normal or an
enlightened VMCS?
Thanks to the bug in Hyper-V (see commit 72aeb60c52bf7 ("KVM: nVMX: Verify
eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD")) we can
not, the revision can't be used to distinguish between them. So let's
assume it is always enlightened in case enlightened vmentry is enabled in
the assist page. Also, check if vmx->nested.enlightened_vmcs_enabled to
minimize the impact for 'unenlightened' workloads.
Fixes: b8bbab928fb1 ("KVM: nVMX: implement enlightened VMPTRLD and VMCLEAR")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Apparently, Windows doesn't maintain clean fields data after it does
VMCLEAR for an enlightened VMCS so we can only use it on VMRESUME.
The issue went unnoticed because currently we do nested_release_evmcs()
in handle_vmclear() and the consecutive enlightened VMPTRLD invalidates
clean fields when a new eVMCS is mapped but we're going to change the
logic.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This allows userspace to know which MSRs are supported by the hypervisor.
Unfortunately userspace must resort to tricks for everything except
MSR_IA32_VMX_VMFUNC (which was just added in the previous patch).
One possibility is to use the feature control MSR, which is tied to nested
VMX as well and is present on all KVM versions that support feature MSRs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Allow userspace to set a custom value for the VMFUNC controls MSR, as long
as the capabilities it advertises do not exceed those of the host.
Fixes: 27c42a1bb ("KVM: nVMX: Enable VMFUNC for the L1 hypervisor", 2017-08-03)
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some secondary controls are automatically enabled/disabled based on the CPUID
values that are set for the guest. However, they are still available at a
global level and therefore should be present when KVM_GET_MSRS is sent to
/dev/kvm.
Fixes: 1389309c811 ("KVM: nVMX: expose VMX capabilities for nested hypervisors to userspace", 2018-02-26)
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
paranoid_exit needs to restore CR3 before GSBASE. Doing it in the opposite
order crashes if the exception came from a context with user GSBASE and
user CR3 -- RESTORE_CR3 cannot resture user CR3 if run with user GSBASE.
This results in infinitely recursing exceptions if user code does SYSENTER
with TF set if both FSGSBASE and PTI are enabled.
The old code worked if user code just set TF without SYSENTER because #DB
from user mode is special cased in idtentry and paranoid_exit doesn't run.
Fix it by cleaning up the spaghetti code. All that paranoid_exit needs to
do is to disable IRQs, handle IRQ tracing, then restore CR3, and restore
GSBASE. Simply do those actions in that order.
Fixes: 708078f65721 ("x86/entry/64: Handle FSGSBASE enabled paranoid entry/exit")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: https://lkml.kernel.org/r/59725ceb08977359489fbed979716949ad45f616.1562035429.git.luto@kernel.org
|
|
It's only used if !CONFIG_IA32_EMULATION, so disable it in normal
configs. This will save a few bytes of text and reduce confusion.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "BaeChang Seok" <chang.seok.bae@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Bae, Chang Seok" <chang.seok.bae@intel.com>
Link: https://lkml.kernel.org/r/0f7dafa72fe7194689de5ee8cfe5d83509fabcf5.1562035429.git.luto@kernel.org
|
|
Doing the indirection through macros for the regs accessors just
makes them harder to read, so implement the helpers directly.
Note that only the helpers actually used are implemented now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull x86 fixes from Ingo Molnar:
"Misc fixes all over the place:
- might_sleep() atomicity fix in the microcode loader
- resctrl boundary condition fix
- APIC arithmethics bug fix for frequencies >= 4.2 GHz
- three 5-level paging crash fixes
- two speculation fixes
- a perf/stacktrace fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Fall back to using frame pointers for generated code
perf/x86: Always store regs->ip in perf_callchain_kernel()
x86/speculation: Allow guests to use SSBD even if host does not
x86/mm: Handle physical-virtual alignment mismatch in phys_p4d_init()
x86/boot/64: Add missing fixup_pointer() for next_early_pgt access
x86/boot/64: Fix crash if kernel image crosses page table boundary
x86/apic: Fix integer overflow on 10 bit left shift of cpu_khz
x86/resctrl: Prevent possible overrun during bitmap operations
x86/microcode: Fix the microcode load on CPU hotplug for real
|
|
Pull perf fixes from Ingo Molnar:
"Various fixes, most of them related to bugs perf fuzzing found in the
x86 code"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/regs: Use PERF_REG_EXTENDED_MASK
perf/x86: Remove pmu->pebs_no_xmm_regs
perf/x86: Clean up PEBS_XMM_REGS
perf/x86/regs: Check reserved bits
perf/x86: Disable extended registers for non-supported PMUs
perf/ioctl: Add check for the sample_period value
perf/core: Fix perf_sample_regs_user() mm check
|
Paolo Bonzini
Krish Sadhukhan
Sean Christopherson
Junaid Shahid
Ingo Molnar
Linus Torvalds
Alexandre Ghiti
David S. Miller
Thomas Gleixner
Wanpeng Li
Luke Nelson
Michael Kelley
Jiri Kosina
Christoph Hellwig
Liran Alon
Jim Mattson
Vitaly Kuznetsov
Andy Lutomirski