| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Each SBDT is located at a 4KB page and contains 512 entries.
Each entry of a SDBT points to a SDB, a 4KB page containing
sampled data. The last entry is a link to another SDBT page.
When an event is created the function sequence executed is:
__hw_perf_event_init()
+--> allocate_buffers()
+--> realloc_sampling_buffers()
+---> alloc_sample_data_block()
Both functions realloc_sampling_buffers() and
alloc_sample_data_block() allocate pages and the allocation
can fail. This is handled correctly and all allocated
pages are freed and error -ENOMEM is returned to the
top calling function. Finally the event is not created.
Once the event has been created, the amount of initially
allocated SDBT and SDB can be too low. This is detected
during measurement interrupt handling, where the amount
of lost samples is calculated. If the number of lost samples
is too high considering sampling frequency and already allocated
SBDs, the number of SDBs is enlarged during the next execution
of cpumsf_pmu_enable().
If more SBDs need to be allocated, functions
realloc_sampling_buffers()
+---> alloc-sample_data_block()
are called to allocate more pages. Page allocation may fail
and the returned error is ignored. A SDBT and SDB setup
already exists.
However the modified SDBTs and SDBs might end up in a situation
where the first entry of an SDBT does not point to an SDB,
but another SDBT, basicly an SBDT without payload.
This can not be handled by the interrupt handler, where an SDBT
must have at least one entry pointing to an SBD.
Add a check to avoid SDBTs with out payload (SDBs) when enlarging
the buffer setup.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The macro TEAR_REG() saves the last used SDBT address
in the perf_hw_event structure. This is also done
by function hw_reset_registers() which is a one-liner
and simply uses macro TEAR_REG(). Remove function
hw_reset_registers(), which is only used one time and use
macro TEAR_REG() instead. This macro is used throughout
the code anyway.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
In interrupt handling the function extend_sampling_buffer()
is called after checking for a possibly extension.
This check is not necessary as the called function itself
performs this check again.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Replace hard coded function names in debug statements
by the "%s ...", __func__ construct suggested by checkpatch.pl
script. Use consistent debug print format of the form variable
blank value. Also add leading 0x for all hex values.
Print allocated page addresses consistantly as hex numbers
with leading 0x.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The KASLR offset is added to vmcoreinfo in arch_crash_save_vmcoreinfo(),
so that it can be found by crash when processing kernel dumps.
However, arch_crash_save_vmcoreinfo() is called during a subsys_initcall,
so if the kernel crashes before that, we have no vmcoreinfo and no KASLR
offset.
Fix this by storing the KASLR offset in the lowcore, where the vmcore_info
pointer will be stored, and where it can be found by crash. In order to
make it distinguishable from a real vmcore_info pointer, mark it as uneven
(KASLR offset itself is aligned to THREAD_SIZE).
When arch_crash_save_vmcoreinfo() stores the real vmcore_info pointer in
the lowcore, it overwrites the KASLR offset. At that point, the KASLR
offset is not yet added to vmcoreinfo, so we also need to move the
mem_assign_absolute() behind the vmcoreinfo_append_str().
Fixes: b2d24b97b2a9 ("s390/kernel: add support for kernel address space layout randomization (KASLR)")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Consider reaching task pt_regs graceful unwinder termination. Task
pt_regs itself never contains a valid state to which a task might return
within the kernel context (user task pt_regs is a special case). Since
we already avoid printing user task pt_regs and in most cases we don't
even bother filling task pt_regs psw and r15 with something reasonable
simply skip task pt_regs altogether. With this change unwind_error() now
accurately represent whether unwinder reached task pt_regs successfully
or failed along the way.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Add missing allocation of pt_regs at the bottom of the stack. This
makes it consistent with other stack setup cases and also what stack
unwinder expects.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently unwinder yields 2 entries when pt_regs are met:
sp="address of pt_regs itself" ip=pt_regs->psw
sp=pt_regs->gprs[15] ip="r14 from stack frame pointed by pt_regs->gprs[15]"
And neither of those 2 states (combination of sp and ip) ever happened.
reuse_sp has been introduced by commit a1d863ac3e10 ("s390/unwind: fix
mixing regs and sp"). reuse_sp=true makes unwinder keen to produce the
following result, when pt_regs are given (as an arg to unwind_start):
sp=pt_regs->gprs[15] ip=pt_regs->psw
sp=pt_regs->gprs[15] ip="r14 from stack frame pointed by pt_regs->gprs[15]"
The first state is an actual state in which a task was when pt_regs were
collected. The second state is marked unreliable and is for debugging
purposes to cover the case when a task has been interrupted in between
stack frame allocation and writing back_chain - in this case r14 might
show an actual caller.
Make unwinder behaviour enabled via reuse_sp=true default and drop the
special case handling.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
If unwinder is looking at pt_regs which is not on stack then something
went wrong and an error has to be reported rather than successful
unwinding termination.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
CALL_ON_STACK is intended to be used for temporary stack switching with
potential return to the caller.
When CALL_ON_STACK is misused to switch from nodat stack to task stack
back_chain information would later lead stack unwinder from task stack into
(per cpu) nodat stack which is reused for other purposes. This would
yield confusing unwinding result or errors.
To avoid that introduce CALL_ON_STACK_NORETURN to be used instead. It
makes sure that back_chain is zeroed and unwinder finishes gracefully
ending up at task pt_regs.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Currently CALL_ON_STACK saves r15 as back_chain in the first stack frame of
the stack we about to switch to. But if a function which uses CALL_ON_STACK
calls other function it allocates a stack frame for a callee. In this
case r15 is pointing to a callee stack frame and not a stack frame of
function itself. This results in dummy unwinding entry with random
sp and ip values.
Introduce and utilize current_frame_address macro to get an address of
actual function stack frame.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Avoid mixture of task == NULL and task == current meaning the same
thing and simply always initialize task with current in unwind_start.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Make sure preemption is disabled when temporary switching to nodat
stack with CALL_ON_STACK helper, because nodat stack is per cpu.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
disabled_wait uses _THIS_IP_ and assumes that compiler would inline it.
Make sure this assumption is always correct by utilizing __always_inline.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
getcpu reads the required values for cpu and node with two
instructions. This might lead to an inconsistent result if user space
gets preempted and migrated to a different CPU between the two
instructions.
Fix this by using just a single instruction to read both values at
once.
This is currently rather a theoretical bug, since there is no real
NUMA support available (except for NUMA emulation).
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When a secondary CPU is brought up it must initialize its control
registers. CPU A which triggers that a secondary CPU B is brought up
stores its control register contents into the lowcore of new CPU B,
which then loads these values on startup.
This is problematic in various ways: the control register which
contains the home space ASCE will correctly contain the kernel ASCE;
however control registers for primary and secondary ASCEs are
initialized with whatever values were present in CPU A.
Typically:
- the primary ASCE will contain the user process ASCE of the process
that triggered onlining of CPU B.
- the secondary ASCE will contain the percpu VDSO ASCE of CPU A.
Due to lazy ASCE handling we may also end up with other combinations.
When then CPU B switches to a different process (!= idle) it will
fixup the primary ASCE. However the problem is that the (wrong) ASCE
from CPU A was loaded into control register 1: as soon as an ASCE is
attached (aka loaded) a CPU is free to generate TLB entries using that
address space.
Even though it is very unlikey that CPU B will actually generate such
entries, this could result in TLB entries of the address space of the
process that ran on CPU A. These entries shouldn't exist at all and
could cause problems later on.
Furthermore the secondary ASCE of CPU B will not be updated correctly.
This means that processes may see wrong results or even crash if they
access VDSO data on CPU B. The correct VDSO ASCE will eventually be
loaded on return to user space as soon as the kernel executed a call
to strnlen_user or an atomic futex operation on CPU B.
Fix both issues by intializing the to be loaded control register
contents with the correct ASCEs and also enforce (re-)loading of the
ASCEs upon first context switch and return to user space.
Fixes: 0aaba41b58bc ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
On s390 bpf_get_stack_raw_tp() returns 0 entries for both kernel and
user stacks. While there is no practical unwinding solution for userspace
on s390 at this moment, there certainly is a kernel unwinder. However,
it is not properly integrated with BPF.
In order to start unwinding, bpf_get_stack_raw_tp() obtains the current
kernel register values using perf_fetch_caller_regs(), which is not
implemented for s390. The actual unwinding then happens by passing those
registers to perf_callchain_kernel().
Implement perf_arch_fetch_caller_regs() for s390, where
__builtin_frame_address(0) points to back_chain.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
system_call assembly code always pushes pointer to struct pt_regs as the
last additional parameter for all system calls. The only user of this
feature is xtensa_rt_sigreturn.
Avoid this special case. Define xtensa_rt_sigreturn as accepting no
argiments. Use current_pt_regs to get pointer to struct pt_regs in
xtensa_rt_sigreturn. Don't pass additional parameter from system_call
code.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Don't overwrite return value if system call was cancelled at entry by
ptrace. Return status code from do_syscall_trace_enter so that
pt_regs::syscall doesn't need to be changed to skip syscall.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
system_call saves and restores syscall number across system call to make
clone and execv entry and exit tracing match. This complicates things
when syscall code may be changed by ptrace.
Preserve syscall code in copy_thread and start_thread directly instead of
doing tricks in system_call.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Commit f2bb86937d86 ("powerpc/fixmap: don't clear fixmap area in
paging_init()") removed the clearing of fixmap area in order to
avoid clearing fixmapped areas set earlier.
However unlike all other users of fixmap which use __set_fixmap(),
HIGHMEM functions directly use __set_pte_at(). This means
the page table must pre-exist, otherwise the following crash
can be encoutered due to the lack of entry in the PGD.
Oops: Kernel access of bad area, sig: 11 [#1]
BE PAGE_SIZE=4K MMU=Hash PowerMac
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.0+ #2528
NIP: c0144ce8 LR: c0144ccc CTR: 00000080
REGS: ef0b5aa0 TRAP: 0300 Not tainted (5.4.0+)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44282842 XER: 00000000
DAR: fffdf000 DSISR: 42000000
GPR00: c0144ccc ef0b5b58 ef0b0000 fffdf000 fffdf000 00000000 c0000f7c 00000000
GPR08: c0833000 fffdf000 00000000 ef1c53c9 24042842 00000000 00000000 00000000
GPR16: 00000000 00000000 ef7e7358 effe8160 00000000 c08a9660 c0851644 00000004
GPR24: c08c70a8 00002dc2 00000000 00000001 00000201 effe8160 effe8160 00000000
NIP [c0144ce8] prep_new_page+0x138/0x178
LR [c0144ccc] prep_new_page+0x11c/0x178
Call Trace:
[ef0b5b58] [c0144ccc] prep_new_page+0x11c/0x178 (unreliable)
[ef0b5b88] [c0147218] get_page_from_freelist+0x1fc/0xd88
[ef0b5c38] [c0148328] __alloc_pages_nodemask+0xd4/0xbb4
[ef0b5cf8] [c0142ba8] __vmalloc_node_range+0x1b4/0x2e0
[ef0b5d38] [c0142dd0] vzalloc+0x48/0x58
[ef0b5d58] [c0301c8c] check_partition+0x58/0x244
[ef0b5d78] [c02ffe80] blk_add_partitions+0x44/0x2cc
[ef0b5db8] [c01a32d8] bdev_disk_changed+0x68/0xfc
[ef0b5de8] [c01a4494] __blkdev_get+0x290/0x460
[ef0b5e28] [c02fdd40] __device_add_disk+0x480/0x4d8
[ef0b5e68] [c0810688] brd_init+0xc0/0x188
[ef0b5e88] [c0005194] do_one_initcall+0x40/0x19c
[ef0b5ee8] [c07dd4dc] kernel_init_freeable+0x164/0x230
[ef0b5f28] [c0005408] kernel_init+0x18/0x10c
[ef0b5f38] [c0014274] ret_from_kernel_thread+0x14/0x1c
Partially revert that commit to still clear the fixmap area dedicated
to HIGHMEM.
Fixes: f2bb86937d86 ("powerpc/fixmap: don't clear fixmap area in paging_init()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d42fa9747df5afa41e67b08e374c98d3b40529c9.1574927918.git.christophe.leroy@c-s.fr
|
|
While writing to MSR IA32_THERM_STATUS/IA32_PKG_THERM_STATUS, avoid
writing 1 to read only and reserved fields because updating some fields
generates exception.
[ bp: Vertically align for better readability. ]
Fixes: f6656208f04e ("x86/mce/therm_throt: Optimize notifications of thermal throttle")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191128150824.22413-1-srinivas.pandruvada@linux.intel.com
|
|
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf script:
Adrian Hunter:
- Fix brstackinsn for AUXTRACE.
- Fix invalid LBR/binary mismatch error.
perf diff:
Arnaldo Carvalho de Melo:
- Use llabs() with 64-bit values, fixing the build in some 32-bit
architectures.
perf pmu:
Andi Kleen:
- Use file system cache to optimize sysfs access.
x86:
Adrian Hunter:
- Add some more Intel instructions to the opcode map and to the perf
test entry:
gf2p8affineinvqb, gf2p8affineqb, gf2p8mulb, v4fmaddps,
v4fmaddss, v4fnmaddps, v4fnmaddss, vaesdec, vaesdeclast, vaesenc,
vaesenclast, vcvtne2ps2bf16, vcvtneps2bf16, vdpbf16ps,
vgf2p8affineinvqb, vgf2p8affineqb, vgf2p8mulb, vp2intersectd,
vp2intersectq, vp4dpwssd, vp4dpwssds, vpclmulqdq, vpcompressb,
vpcompressw, vpdpbusd, vpdpbusds, vpdpwssd, vpdpwssds, vpexpandb,
vpexpandw, vpopcntb, vpopcntd, vpopcntq, vpopcntw, vpshldd, vpshldq,
vpshldvd, vpshldvq, vpshldvw, vpshldw, vpshrdd, vpshrdq, vpshrdvd,
vpshrdvq, vpshrdvw, vpshrdw, vpshufbitqmb.
perf affinity:
Andi Kleen:
- Add infrastructure to save/restore affinity
perf maps:
Arnaldo Carvalho de Melo:
- Merge 'struct maps' with 'struct map_groups', as there is a
1x1 relationship, simplifying code overal.
perf build:
Jiri Olsa:
- Allow to link with libbpf dynamicaly.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull dma-mapping updates from Christoph Hellwig:
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using DMA offsets
(Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas
Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
* tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits)
dma-mapping: treat dev->bus_dma_mask as a DMA limit
dma-direct: exclude dma_direct_map_resource from the min_low_pfn check
dma-direct: don't check swiotlb=force in dma_direct_map_resource
dma-debug: clean up put_hash_bucket()
powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys
dma-direct: avoid a forward declaration for phys_to_dma
dma-direct: unify the dma_capable definitions
dma-mapping: drop the dev argument to arch_sync_dma_for_*
x86/PCI: sta2x11: use default DMA address translation
dma-direct: check for overflows on 32 bit DMA addresses
dma-debug: increase HASH_SIZE
dma-debug: reorder struct dma_debug_entry fields
xtensa: use the generic uncached segment support
dma-mapping: merge the generic remapping helpers into dma-direct
dma-direct: provide mmap and get_sgtable method overrides
dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages
dma-direct: remove __dma_direct_free_pages
usb: core: Remove redundant vmap checks
kernel: dma-contiguous: mark CMA parameters __initdata/__initconst
dma-debug: add a schedule point in debug_dma_dump_mappings()
...
|
|
Pull generic ioremap support from Christoph Hellwig:
"This adds the remaining bits for an entirely generic ioremap and
iounmap to lib/ioremap.c. To facilitate that, it cleans up the giant
mess of weird ioremap variants we had with no users outside the arch
code.
For now just the three newest ports use the code, but there is more
than a handful others that can be converted without too much work.
Summary:
- clean up various obsolete ioremap and iounmap variants
- add a new generic ioremap implementation and switch csky, nds32 and
riscv over to it"
* tag 'ioremap-5.5' of git://git.infradead.org/users/hch/ioremap: (21 commits)
nds32: use generic ioremap
csky: use generic ioremap
csky: remove ioremap_cache
riscv: use the generic ioremap code
lib: provide a simple generic ioremap implementation
sh: remove __iounmap
nios2: remove __iounmap
hexagon: remove __iounmap
m68k: rename __iounmap and mark it static
arch: rely on asm-generic/io.h for default ioremap_* definitions
asm-generic: don't provide ioremap for CONFIG_MMU
asm-generic: ioremap_uc should behave the same with and without MMU
xtensa: clean up ioremap
x86: Clean up ioremap()
parisc: remove __ioremap
nios2: remove __ioremap
alpha: remove the unused __ioremap wrapper
hexagon: clean up ioremap
ia64: rename ioremap_nocache to ioremap_uc
unicore32: remove ioremap_cached
...
|
|
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY (Neil
Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe combo
PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT (Neil
Armstrong)
* remotes/lorenzo/pci/meson:
arm64: dts: khadas-vim3: add commented support for PCIe
arm64: dts: meson-g12a: Add PCIe node
phy: meson-g12a-usb3-pcie: Add support for PCIe mode
PCI: amlogic: meson: Add support for G12A
PCI: amlogic: Fix probed clock names
dt-bindings: pci: amlogic, meson-pcie: Add G12A bindings
PCI: amlogic: Fix reset assertion via gpio descriptor
|
|
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
|
|
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk for
Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
* pci/msi:
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
|
|
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on USB
2.0 or 1.1 connect events (Kai-Heng Feng)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and Radeon
CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word() in
AMDGPU and Radeon CIK/SI (Frederick Lawler)
* pci/misc:
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/amdgpu: Correct Transmit Margin masks
PCI: Add #defines for Enter Compliance, Transmit Margin
PCI: Allow building PCIe things without PCIEPORTBUS
PCI: Remove PCIe Kconfig dependencies on PCI
PCI/ASPM: Remove dependency on PCIEPORTBUS
PCI/PTM: Remove dependency on PCIEPORTBUS
PCI/PTM: Remove spurious "d" from granularity message
PCI: sysfs: Remove unused attribute groups
x86/PCI: Avoid AMD FCH XHCI USB PME# from D0 defect
PCI: Remove unused includes and superfluous struct declaration
x86/PCI: Replace deprecated EXTRA_CFLAGS with ccflags-y
x86/PCI: Correct SPDX comment style
x86/PCI: Add NumaChip SPDX GPL-2.0 to replace COPYING boilerplate
|
|
The state/owner of the FPU is saved to fpu_fpregs_owner_ctx by pointing
to the context that is currently loaded. It never changed during the
lifetime of a task - it remained stable/constant.
After deferred FPU registers loading until return to userland was
implemented, the content of fpu_fpregs_owner_ctx may change during
preemption and must not be cached.
This went unnoticed for some time and was now noticed, in particular
since gcc 9 is caching that load in copy_fpstate_to_sigframe() and
reusing it in the retry loop:
copy_fpstate_to_sigframe()
load fpu_fpregs_owner_ctx and save on stack
fpregs_lock()
copy_fpregs_to_sigframe() /* failed */
fpregs_unlock()
*** PREEMPTION, another uses FPU, changes fpu_fpregs_owner_ctx ***
fault_in_pages_writeable() /* succeed, retry */
fpregs_lock()
__fpregs_load_activate()
fpregs_state_valid() /* uses fpu_fpregs_owner_ctx from stack */
copy_fpregs_to_sigframe() /* succeeds, random FPU content */
This is a comparison of the assembly produced by gcc 9, without vs with this
patch:
| # arch/x86/kernel/fpu/signal.c:173: if (!access_ok(buf, size))
| cmpq %rdx, %rax # tmp183, _4
| jb .L190 #,
|-# arch/x86/include/asm/fpu/internal.h:512: return fpu == this_cpu_read_stable(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
|-#APP
|-# 512 "arch/x86/include/asm/fpu/internal.h" 1
|- movq %gs:fpu_fpregs_owner_ctx,%rax #, pfo_ret__
|-# 0 "" 2
|-#NO_APP
|- movq %rax, -88(%rbp) # pfo_ret__, %sfp
…
|-# arch/x86/include/asm/fpu/internal.h:512: return fpu == this_cpu_read_stable(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
|- movq -88(%rbp), %rcx # %sfp, pfo_ret__
|- cmpq %rcx, -64(%rbp) # pfo_ret__, %sfp
|+# arch/x86/include/asm/fpu/internal.h:512: return fpu == this_cpu_read(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
|+#APP
|+# 512 "arch/x86/include/asm/fpu/internal.h" 1
|+ movq %gs:fpu_fpregs_owner_ctx(%rip),%rax # fpu_fpregs_owner_ctx, pfo_ret__
|+# 0 "" 2
|+# arch/x86/include/asm/fpu/internal.h:512: return fpu == this_cpu_read(fpu_fpregs_owner_ctx) && cpu == fpu->last_cpu;
|+#NO_APP
|+ cmpq %rax, -64(%rbp) # pfo_ret__, %sfp
Use this_cpu_read() instead this_cpu_read_stable() to avoid caching of
fpu_fpregs_owner_ctx during preemption points.
The Fixes: tag points to the commit where deferred FPU loading was
added. Since this commit, the compiler is no longer allowed to move the
load of fpu_fpregs_owner_ctx somewhere else / outside of the locked
section. A task preemption will change its value and stale content will
be observed.
[ bp: Massage. ]
Debugged-by: Austin Clements <austin@google.com>
Debugged-by: David Chase <drchase@golang.org>
Debugged-by: Ian Lance Taylor <ian@airs.com>
Fixes: 5f409e20b7945 ("x86/fpu: Defer FPU state load until return to userspace")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Rik van Riel <riel@surriel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: Austin Clements <austin@google.com>
Cc: Barret Rhoden <brho@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Chase <drchase@golang.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: ian@airs.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Bleecher Snyder <josharian@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191128085306.hxfa2o3knqtu4wfn@linutronix.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205663
|
|
Pull tracing updates from Steven Rostedt:
"New tracing features:
- New PERMANENT flag to ftrace_ops when attaching a callback to a
function.
As /proc/sys/kernel/ftrace_enabled when set to zero will disable
all attached callbacks in ftrace, this has a detrimental impact on
live kernel tracing, as it disables all that it patched. If a
ftrace_ops is registered to ftrace with the PERMANENT flag set, it
will prevent ftrace_enabled from being disabled, and if
ftrace_enabled is already disabled, it will prevent a ftrace_ops
with PREMANENT flag set from being registered.
- New register_ftrace_direct().
As eBPF would like to register its own trampolines to be called by
the ftrace nop locations directly, without going through the ftrace
trampoline, this function has been added. This allows for eBPF
trampolines to live along side of ftrace, perf, kprobe and live
patching. It also utilizes the ftrace enabled_functions file that
keeps track of functions that have been modified in the kernel, to
allow for security auditing.
- Allow for kernel internal use of ftrace instances.
Subsystems in the kernel can now create and destroy their own
tracing instances which allows them to have their own tracing
buffer, and be able to record events without worrying about other
users from writing over their data.
- New seq_buf_hex_dump() that lets users use the hex_dump() in their
seq_buf usage.
- Notifications now added to tracing_max_latency to allow user space
to know when a new max latency is hit by one of the latency
tracers.
- Wider spread use of generic compare operations for use of bsearch
and friends.
- More synthetic event fields may be defined (32 up from 16)
- Use of xarray for architectures with sparse system calls, for the
system call trace events.
This along with small clean ups and fixes"
* tag 'trace-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (51 commits)
tracing: Enable syscall optimization for MIPS
tracing: Use xarray for syscall trace events
tracing: Sample module to demonstrate kernel access to Ftrace instances.
tracing: Adding new functions for kernel access to Ftrace instances
tracing: Fix Kconfig indentation
ring-buffer: Fix typos in function ring_buffer_producer
ftrace: Use BIT() macro
ftrace: Return ENOTSUPP when DYNAMIC_FTRACE_WITH_DIRECT_CALLS is not configured
ftrace: Rename ftrace_graph_stub to ftrace_stub_graph
ftrace: Add a helper function to modify_ftrace_direct() to allow arch optimization
ftrace: Add helper find_direct_entry() to consolidate code
ftrace: Add another check for match in register_ftrace_direct()
ftrace: Fix accounting bug with direct->count in register_ftrace_direct()
ftrace/selftests: Fix spelling mistake "wakeing" -> "waking"
tracing: Increase SYNTH_FIELDS_MAX for synthetic_events
ftrace/samples: Add a sample module that implements modify_ftrace_direct()
ftrace: Add modify_ftrace_direct()
tracing: Add missing "inline" in stub function of latency_fsnotify()
tracing: Remove stray tab in TRACE_EVAL_MAP_FILE's help text
tracing: Use seq_buf_hex_dump() to dump buffers
...
|
|
Pull Microblaze updates from Michal Simek:
- extend DTB space
- defconfig update
- clean up rescheduling logic
- enable SPARSE_IRQ
* tag 'microblaze-v5.5-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Increase max dtb size to 64K from 32K
microblaze: Enable SPARSE_IRQ
microblaze: defconfig: Enable devtmps and tmpfs
microblaze: entry: Remove unneeded need_resched() loop
|
|
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
|
|
Pull powerpc Spectre-RSB fixes from Michael Ellerman:
"We failed to activate the mitigation for Spectre-RSB (Return Stack
Buffer, aka. ret2spec) on context switch, on CPUs prior to Power9
DD2.3.
That allows a process to poison the RSB (called Link Stack on Power
CPUs) and possibly misdirect speculative execution of another process.
If the victim process can be induced to execute a leak gadget then it
may be possible to extract information from the victim via a side
channel.
The fix is to correctly activate the link stack flush mitigation on
all CPUs that have any mitigation of Spectre v2 in userspace enabled.
There's a second commit which adds a link stack flush in the KVM guest
exit path. A leak via that path has not been demonstrated, but we
believe it's at least theoretically possible.
This is the fix for CVE-2019-18660"
* tag 'powerpc-spectre-rsb' of /home/torvalds/Downloads/powerpc-CVE-2019-18660.bundle:
KVM: PPC: Book3S HV: Flush link stack on guest exit to host kernel
powerpc/book3s64: Fix link stack flush on context switch
|
|
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
|
|
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
|
|
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
|
|
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v5.5.
It is pretty much business as usual, the most interesting thing I
think is the pin controller for a new Intel chip called Lightning
Mountain, which is according to news reports some kind of embedded
network processor and what is surprising about it is that Intel have
decided to use device tree to describe the system rather than ACPI
that they have traditionally favored.
Core changes:
- Avoid taking direct references to device tree-supplied device
names: these may changed at runtime under certain circumstances to
kstrdup them.
GPIO related:
- Work is ongoing to move to passing the irqchip along as a templated
struct gpio_irq_chip when adding a standard gpiolib-based irqchip
to a GPIO controller, a few patches in this cycle switches a few
pin control drivers over to using this method.
New hardware support:
- Intel Lightning Mountain SoC pin controller and GPIO support, a
first Intel platform to use device tree rather than ACPI to
configure the system. News reports says that this SoC is a network
processor.
- Qualcomm MSM8976 and MSM8956
- Qualcomm PMIC GPIO now also supports PM6150 and PM6150L
- Qualcomm SPMI MPP and SPMI GPIO for PM8950 and PMI8950
- Rockchip RK3308
- Renesas R8A77961
- Allwinner Meson-A1
Driver improvements:
- get_multiple and set_multiple support for the AT91-PIO4 driver.
- Convert Qualcomm SSBI GPIO to use the hierarchical IRQ helpers in
the GPIOlib irqchip"
* tag 'pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: ingenic: Add OTG VBUS pin for the JZ4770
pinctrl: ingenic: Handle PIN_CONFIG_OUTPUT config
pinctrl: Fix Kconfig indentation
pinctrl: lewisburg: Update pin list according to v1.1v6
MAINTAINERS: Replace my email by one @kernel.org
pinctrl: armada-37xx: Fix irq mask access in armada_37xx_irq_set_type()
dt-bindings: pinctrl: intel: Add for new SoC
pinctrl: Add pinmux & GPIO controller driver for a new SoC
pinctrl: rza1: remove unnecessary static inline function
pinctrl: meson: add pinctrl driver support for Meson-A1 SoC
pinctrl: meson: add a new callback for SoCs fixup
pinctrl: nomadik: db8500: Add mc0_a_2 pin group without direction control
dt-bindings: pinctrl: Convert generic pin mux and config properties to schema
pinctrl: cherryview: Missed type change to unsigned int
pinctrl: intel: Missed type change to unsigned int
pinctrl: use devm_platform_ioremap_resource() to simplify code
pinctrl: just return if no valid maps
dt-bindings: pinctrl: qcom-pmic-mpp: Add support for PM/PMI8950
pinctrl: qcom: spmi-mpp: Add PM/PMI8950 compatible strings
dt-bindings: pinctrl: qcom-pmic-gpio: Add support for PM/PMI8950
...
|
|
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
|
|
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When you successfully write 0 to /sys/devices/cpu/rdpmc, the RDPMC
instruction should be disabled unconditionally and immediately (after you
close the SYSFS file) by the documentation.
Instead, in the current implementation the PMU must be reloaded which
happens only eventually some time in the future. Only after that the RDPMC
instruction becomes disabled (on ring 3) on the respective core.
This change makes the treatment of the 0 value as blocking and as
unconditional as the current treatment of the 2 value, only the CR4.PCE
bit is naturally set to false instead of true.
Signed-off-by: Anthony Steinhauser <asteinhauser@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Link: https://lkml.kernel.org/r/20191125054838.137615-1-asteinhauser@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Under certain circumstances, we hit a warning in lockdep_register_key:
if (WARN_ON_ONCE(static_obj(key)))
return;
This occurs when the key falls into initmem that has since been freed
and can now be reused. This has been observed on boot, and under
memory pressure.
Define arch_is_kernel_initmem_freed(), which allows lockdep to
correctly identify this memory as dynamic.
This fixes a bug picked up by the powerpc64 syzkaller instance where
we hit the WARN via alloc_netdev_mqs.
Reported-by: Qian Cai <cai@lca.pw>
Reported-by: ppc syzbot c/o Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/87lfs4f7d6.fsf@dja-thinkpad.axtens.net
|
|
For glue code that's used by Zinc, the actual Crypto API functions might
not necessarily exist, and don't need to exist either. Before this
patch, there are valid build configurations that lead to a unbuildable
kernel. This fixes it to conditionalize those symbols on the existence
of the proper config entry.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull media updates from Mauro Carvalho Chehab:
- uAPI documentation for stateless decoders
- Added a new CEC ioctl together with its documentation
- Improved IPU3 documentation
- New i2c drivers: hi556 and imx290
- Added support on Vivid driver for meta streams
- Added de-interlace support for sunxi subdriver
- Added a few new remote controler keymaps
- Added H.265 support for Sunxi Cedrus driver
- Another round of random driver cleanups, fixes and improvements
* tag 'media/v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
|
|
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20191018, add support for EFI specific purpose memory, update the ACPI
EC driver to make it work on systems with hardware-reduced ACPI,
improve ACPI-based device enumeration for some platforms, rework the
lid blacklist handling in the button driver and add more lid quirks to
it, unify ACPI _HID/_UID matching, fix assorted issues and clean up
the code and documentation.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20191018
including:
* Fixes for Clang warnings (Bob Moore)
* Fix for possible overflow in get_tick_count() (Bob Moore)
* Introduction of acpi_unload_table() (Bob Moore)
* Debugger and utilities updates (Erik Schmauss)
* Fix for unloading tables loaded via configfs (Nikolaus Voss)
- Add support for EFI specific purpose memory to optionally allow
either application-exclusive or core-kernel-mm managed access to
differentiated memory (Dan Williams)
- Fix and clean up processing of the HMAT table (Brice Goglin, Qian
Cai, Tao Xu)
- Update the ACPI EC driver to make it work on systems with
hardware-reduced ACPI (Daniel Drake)
- Always build in support for the Generic Event Device (GED) to allow
one kernel binary to work both on systems with full hardware ACPI
and hardware-reduced ACPI (Arjan van de Ven)
- Fix the table unload mechanism to unregister platform devices
created when the given table was loaded (Andy Shevchenko)
- Rework the lid blacklist handling in the button driver and add more
lid quirks to it (Hans de Goede)
- Improve ACPI-based device enumeration for some platforms based on
Intel BayTrail SoCs (Hans de Goede)
- Add an OpRegion driver for the Cherry Trail Crystal Cove PMIC and
prevent handlers from being registered for unhandled PMIC OpRegions
(Hans de Goede)
- Unify ACPI _HID/_UID matching (Andy Shevchenko)
- Clean up documentation and comments (Cao jin, James Pack, Kacper
Piwiński)"
* tag 'acpi-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
ACPI: OSI: Shoot duplicate word
ACPI: HMAT: use %u instead of %d to print u32 values
ACPI: NUMA: HMAT: fix a section mismatch
ACPI: HMAT: don't mix pxm and nid when setting memory target processor_pxm
ACPI: NUMA: HMAT: Register "soft reserved" memory as an "hmem" device
ACPI: NUMA: HMAT: Register HMAT at device_initcall level
device-dax: Add a driver for "hmem" devices
dax: Fix alloc_dax_region() compile warning
lib: Uplevel the pmem "region" ida to a global allocator
x86/efi: Add efi_fake_mem support for EFI_MEMORY_SP
arm/efi: EFI soft reservation to memblock
x86/efi: EFI soft reservation to E820 enumeration
efi: Common enable/disable infrastructure for EFI soft reservation
x86/efi: Push EFI_MEMMAP check into leaf routines
efi: Enumerate EFI_MEMORY_SP
ACPI: NUMA: Establish a new drivers/acpi/numa/ directory
ACPICA: Update version to 20191018
ACPICA: debugger: remove leading whitespaces when converting a string to a buffer
ACPICA: acpiexec: initialize all simple types and field units from user input
ACPICA: debugger: add field unit support for acpi_db_get_next_token
...
|
|
Pull power management updates from Rafael Wysocki:
"These include cpuidle changes to use nanoseconds (instead of
microseconds) as the unit of time and to simplify checks for disabled
idle states in the idle loop, some cpuidle fixes and governor updates,
assorted cpufreq updates (driver updates mostly and a few core fixes
and cleanups), devfreq updates (dominated by the tegra30 driver
changes), new CPU IDs for the RAPL power capping driver, relatively
minor updates of the generic power domains (genpd) and operation
performance points (OPP) frameworks, and assorted fixes and cleanups.
There are also two maintainer information updates: Chanwoo Choi will
be maintaining the devfreq subsystem going forward and Todd Brandt is
going to maintain the pm-graph utility (created by him).
Specifics:
- Use nanoseconds (instead of microseconds) as the unit of time in
the cpuidle core and simplify checks for disabled idle states in
the idle loop (Rafael Wysocki)
- Fix and clean up the teo cpuidle governor (Rafael Wysocki)
- Fix the cpuidle registration error code path (Zhenzhong Duan)
- Avoid excessive vmexits in the ACPI cpuidle driver (Yin Fengwei)
- Extend the idle injection infrastructure to be able to measure the
requested duration in nanoseconds and to allow an exit latency
limit for idle states to be specified (Daniel Lezcano)
- Fix cpufreq driver registration and clarify a comment in the
cpufreq core (Viresh Kumar)
- Add NULL checks to the show() and store() methods of sysfs
attributes exposed by cpufreq (Kai Shen)
- Update cpufreq drivers:
* Fix for a plain int as pointer warning from sparse in
intel_pstate (Jamal Shareef)
* Fix for a hardcoded number of CPUs and stack bloat in the
powernv driver (John Hubbard)
* Updates to the ti-cpufreq driver and DT files to support new
platforms and migrate bindings from opp-v1 to opp-v2 (Adam Ford,
H. Nikolaus Schaller)
* Merging of the arm_big_little and vexpress-spc drivers and
related cleanup (Sudeep Holla)
* Fix for imx's default speed grade value (Anson Huang)
* Minor cleanup of the s3c64xx driver (Nathan Chancellor)
* CPU speed bin detection fix for sun50i (Ondrej Jirman)
- Appoint Chanwoo Choi as the new devfreq maintainer.
- Update the devfreq core:
* Check NULL governor in available_governors_show sysfs to prevent
showing wrong governor information and fix a race condition
between devfreq_update_status() and trans_stat_show() (Leonard
Crestez)
* Add new 'interrupt-driven' flag for devfreq governors to allow
interrupt-driven governors to prevent the devfreq core from
polling devices for status (Dmitry Osipenko)
* Improve an error message in devfreq_add_device() (Matthias
Kaehlcke)
- Update devfreq drivers:
* tegra30 driver fixes and cleanups (Dmitry Osipenko)
* Removal of unused property from dt-binding documentation for the
exynos-bus driver (Kamil Konieczny)
* exynos-ppmu cleanup and DT bindings update (Lukasz Luba, Marek
Szyprowski)
- Add new CPU IDs for CometLake Mobile and Desktop to the Intel RAPL
power capping driver (Zhang Rui)
- Allow device initialization in the generic power domains (genpd)
framework to be more straightforward and clean it up (Ulf Hansson)
- Add support for adjusting OPP voltages at run time to the OPP
framework (Stephen Boyd)
- Avoid freeing memory that has never been allocated in the
hibernation core (Andy Whitcroft)
- Clean up function headers in a header file and coding style in the
wakeup IRQs handling code (Ulf Hansson, Xiaofei Tan)
- Clean up the SmartReflex adaptive voltage scaling (AVS) driver for
ARM (Ben Dooks, Geert Uytterhoeven)
- Wrap power management documentation to fit in 80 columns (Bjorn
Helgaas)
- Add pm-graph utility entry to MAINTAINERS (Todd Brandt)
- Update the cpupower utility:
* Fix the handling of set and info subcommands (Abhishek Goel)
* Fix build warnings (Nathan Chancellor)
* Improve mperf_monitor handling (Janakarajan Natarajan)"
* tag 'pm-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (83 commits)
PM: Wrap documentation to fit in 80 columns
cpuidle: Pass exit latency limit to cpuidle_use_deepest_state()
cpuidle: Allow idle injection to apply exit latency limit
cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks
cpuidle: teo: Avoid code duplication in conditionals
cpufreq: Register drivers only after CPU devices have been registered
cpuidle: teo: Avoid using "early hits" incorrectly
cpuidle: teo: Exclude cpuidle overhead from computations
PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
PM / Domains: Implement the ->start() callback for genpd
PM / Domains: Introduce dev_pm_domain_start()
ARM: OMAP2+: SmartReflex: add omap_sr_pdata definition
PM / wakeirq: remove unnecessary parentheses
power: avs: smartreflex: Remove superfluous cast in debugfs_create_file() call
cpuidle: Use nanoseconds as the unit of time
PM / OPP: Support adjusting OPP voltages at runtime
PM / core: Clean up some function headers in power.h
cpufreq: Add NULL checks to show() and store() methods of cpufreq
cpufreq: intel_pstate: Fix plain int as pointer warning from sparse
...
|
|
Pull x86 merge fix from Ingo Molnar:
"I missed one other semantic conflict that can result in build failures
on certain stripped down x86 32-bit configs, for example 32-bit
'allnoconfig' where CONFIG_X86_IOPL_IOPERM gets turned off"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/iopl: Make 'struct tss_struct' constant size again
|
|
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
|
|
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Dynamic tick (nohz) updates, perhaps most notably changes to force
the tick on when needed due to lengthy in-kernel execution on CPUs
on which RCU is waiting.
- Linux-kernel memory consistency model updates.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
rcu: Suppress levelspread uninitialized messages
rcu: Fix uninitialized variable in nocb_gp_wait()
rcu: Update descriptions for rcu_future_grace_period tracepoint
rcu: Update descriptions for rcu_nocb_wake tracepoint
rcu: Remove obsolete descriptions for rcu_barrier tracepoint
rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
workqueue: Convert for_each_wq to use built-in list check
rcu: Several rcu_segcblist functions can be static
rcu: Remove unused function hlist_bl_del_init_rcu()
Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
...
|
|
Pull scheduler updates from Ingo Molnar:
"The biggest changes in this cycle were:
- Make kcpustat vtime aware (Frederic Weisbecker)
- Rework the CFS load_balance() logic (Vincent Guittot)
- Misc cleanups, smaller enhancements, fixes.
The load-balancing rework is the most intrusive change: it replaces
the old heuristics that have become less meaningful after the
introduction of the PELT metrics, with a grounds-up load-balancing
algorithm.
As such it's not really an iterative series, but replaces the old
load-balancing logic with the new one. We hope there are no
performance regressions left - but statistically it's highly probable
that there *is* going to be some workload that is hurting from these
chnages. If so then we'd prefer to have a look at that workload and
fix its scheduling, instead of reverting the changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
rackmeter: Use vtime aware kcpustat accessor
leds: Use all-in-one vtime aware kcpustat accessor
cpufreq: Use vtime aware kcpustat accessors for user time
procfs: Use all-in-one vtime aware kcpustat accessor
sched/vtime: Bring up complete kcpustat accessor
sched/cputime: Support other fields on kcpustat_field()
sched/cpufreq: Move the cfs_rq_util_change() call to cpufreq_update_util()
sched/fair: Add comments for group_type and balancing at SD_NUMA level
sched/fair: Fix rework of find_idlest_group()
sched/uclamp: Fix overzealous type replacement
sched/Kconfig: Fix spelling mistake in user-visible help text
sched/core: Further clarify sched_class::set_next_task()
sched/fair: Use mul_u32_u32()
sched/core: Simplify sched_class::pick_next_task()
sched/core: Optimize pick_next_task()
sched/core: Make pick_next_task_idle() more consistent
sched/fair: Better document newidle_balance()
leds: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
cpufreq: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
procfs: Use vtime aware kcpustat accessor to fetch CPUTIME_SYSTEM
...
|
Thomas Richter
Gerald Schaefer
Vasily Gorbik
Heiko Carstens
Ilya Leoshkevich
Max Filippov
Christophe Leroy
Srinivas Pandruvada
Ingo Molnar
Linus Torvalds
Bjorn Helgaas
Sebastian Andrzej Siewior
Borislav Petkov
Anthony Steinhauser
Michael Ellerman
Jason A. Donenfeld