| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The current delay settings of the phy are not the optimal value,
fix it with correct values.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default impedance settings of the phy is not the optimal
value, due to this the second ethernet is not working. Fix it
with correct values which makes the second ethernet port to work.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
|
|
Pull fbdev updates from Tomi Valkeinen:
"Main changes:
- amba-cldc: DT backlight support, Nomadik support, Versatile
improvements, fixes
- efifb: fix fbcon RGB565 palette
- exynos: remove unused DSI driver"
* tag 'fbdev-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (42 commits)
video: smscufx: remove unused variable
matroxfb: fix size of memcpy
fbdev: ssd1307fb: fix a possible NULL dereference
fbdev: ssd1307fb: constify the device_info pointer
simplefb: Disable and release clocks and regulators in destroy callback
video: fbdev: constify fb_fix_screeninfo and fb_var_screeninfo structures
matroxfb: constify local structures
video: fbdev: i810: add in missing white space in error message text
video: fbdev: add missing \n at end of printk error message
ARM: exynos_defconfig: Remove old non-working MIPI driver
video: fbdev: exynos: Remove old non-working MIPI driver
omapfb: fix return value check in dsi_bind()
MAINTAINERS: update fbdev entries
video: fbdev: offb: Call pci_enable_device() before using the PCI VGA device
fbdev: vfb: simplify memory management
fbdev: vfb: add option for video mode
fbdev: vfb: add description to module parameters
video: fbdev: intelfb: remove impossible condition
fb: adv7393: off by one in probe function
video: fbdev: pxafb: add missing of_node_put() in of_get_pxafb_mode_info()
...
|
|
Pull parisc fixes from Helge Deller:
"Some final updates and fixes for this merge window for the parisc
architecture. Changes include:
- Fix boot problems with new memblock allocator on rp3410 machine
- Increase initial kernel mapping size for 32- and 64-bit kernels,
this allows to boot bigger kernels which have many modules built-in
- Fix kernel layout regarding __gp and move exception table into RO
section
- Show trap names in crashes, use extable.h header instead of
module.h"
* 'parisc-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Show trap name in kernel crash
parisc: Zero-initialize newly alloced memblock
parisc: Move exception table into read-only section
parisc: Fix kernel memory layout regarding position of __gp
parisc: Increase initial kernel mapping size
parisc: Migrate exception table users off module.h and onto extable.h
|
|
Pull uaccess.h prepwork from Al Viro:
"Preparations to tree-wide switch to use of linux/uaccess.h (which,
obviously, will allow to start unifying stuff for real). The last step
there, ie
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
`git grep -l "$PATT"|grep -v ^include/linux/uaccess.h`
is not taken here - I would prefer to do it once just before or just
after -rc1. However, everything should be ready for it"
* 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove a stray reference to asm/uaccess.h in docs
sparc64: separate extable_64.h, switch elf_64.h to it
score: separate extable.h, switch module.h to it
mips: separate extable.h, switch module.h to it
x86: separate extable.h, switch sections.h to it
remove stray include of asm/uaccess.h from cacheflush.h
mn10300: remove a bogus processor.h->uaccess.h include
xtensa: split uaccess.h into C and asm sides
bonding: quit messing with IOCTL
kill __kernel_ds_p off
mn10300: finish verify_area() off
frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h
exceptions: detritus removal
|
|
Enable CONFIG_GPIO_XGENE_SB.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm updates from Dave Airlie:
"Core:
- Fence destaging work
- DRIVER_LEGACY to split off legacy drm drivers
- drm_mm refactoring
- Splitting drm_crtc.c into chunks and documenting better
- Display info fixes
- rbtree support for prime buffer lookup
- Simple VGA DAC driver
Panel:
- Add Nexus 7 panel
- More simple panels
i915:
- Refactoring GEM naming
- Refactored vma/active tracking
- Lockless request lookups
- Better stolen memory support
- FBC fixes
- SKL watermark fixes
- VGPU improvements
- dma-buf fencing support
- Better DP dongle support
amdgpu:
- Powerplay for Iceland asics
- Improved GPU reset support
- UVD/VEC powergating support for CZ/ST
- Preinitialised VRAM buffer support
- Virtual display support
- Initial SI support
- GTT rework
- PCI shutdown callback support
- HPD IRQ storm fixes
amdkfd:
- bugfixes
tilcdc:
- Atomic modesetting support
mediatek:
- AAL + GAMMA engine support
- Hook up gamma LUT
- Temporal dithering support
imx:
- Pixel clock from devicetree
- drm bridge support for LVDS bridges
- active plane reconfiguration
- VDIC deinterlacer support
- Frame synchronisation unit support
- Color space conversion support
analogix:
- PSR support
- Better panel on/off support
rockchip:
- rk3399 vop/crtc support
- PSR support
vc4:
- Interlaced vblank timing
- 3D rendering CPU overhead reduction
- HDMI output fixes
tda998x:
- HDMI audio ASoC support
sunxi:
- Allwinner A33 support
- better TCON support
msm:
- DT binding cleanups
- Explicit fence-fd support
sti:
- remove sti415/416 support
etnaviv:
- MMUv2 refactoring
- GC3000 support
exynos:
- Refactoring HDMI DCC/PHY
- G2D pm regression fix
- Page fault issues with wait for vblank
There is no nouveau work in this tree, as Ben didn't get a pull
request in, and he was fighting moving to atomic and adding mst
support, so maybe best it waits for a cycle"
* tag 'drm-for-v4.9' of git://people.freedesktop.org/~airlied/linux: (1412 commits)
drm/crtc: constify drm_crtc_index parameter
drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next
drm/i915/guc: Unwind GuC workqueue reservation if request construction fails
drm/i915: Reset the breadcrumbs IRQ more carefully
drm/i915: Force relocations via cpu if we run out of idle aperture
drm/i915: Distinguish last emitted request from last submitted request
drm/i915: Allow DP to work w/o EDID
drm/i915: Move long hpd handling into the hotplug work
drm/i915/execlists: Reinitialise context image after GPU hang
drm/i915: Use correct index for backtracking HUNG semaphores
drm/i915: Unalias obj->phys_handle and obj->userptr
drm/i915: Just clear the mmiodebug before a register access
drm/i915/gen9: only add the planes actually affected by ddb changes
drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED
drm/i915/bxt: Fix HDMI DPLL configuration
drm/i915/gen9: fix the watermark res_blocks value
drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations
drm/i915/gen9: minimum scanlines for Y tile is not always 4
drm/i915/gen9: fix the WaWmMemoryReadLatency implementation
drm/i915/kbl: KBL also needs to run the SAGV code
...
|
|
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
|
|
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
KASLR memory randomization can randomize the base of the physical memory
mapping (PAGE_OFFSET), vmalloc (VMALLOC_START) and vmemmap
(VMEMMAP_START). Adding these variables on VMCOREINFO so tools can easily
identify the base of each memory section.
Link: http://lkml.kernel.org/r/1471531632-23003-1-git-send-email-thgarnie@google.com
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Eugene Surovegin <surovegin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).
In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online. As the result, kdump
routines fail to save other CPUs' registers. Additionally for MIPS
OCTEON, it misses to stop the watchdog timer.
To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled. crash_smp_send_stop() is a
weak function, and it just call smp_send_stop(). Architecture
codes should override it so that kdump can work appropriately.
This patch provides MIPS version.
Fixes: f06e5153f4ae (kernel/panic.c: add "crash_kexec_post_notifiers" option)
Link: http://lkml.kernel.org/r/20160810080950.11028.28000.stgit@sysi4-13.yrl.intra.hitachi.co.jp
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reported-by: Daniel Walker <dwalker@fifo99.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Xunlei Pang <xpang@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Daniel Walker reported problems which happens when
crash_kexec_post_notifiers kernel option is enabled
(https://lkml.org/lkml/2015/6/24/44).
In that case, smp_send_stop() is called before entering kdump routines
which assume other CPUs are still online. As the result, for x86, kdump
routines fail to save other CPUs' registers and disable virtualization
extensions.
To fix this problem, call a new kdump friendly function,
crash_smp_send_stop(), instead of the smp_send_stop() when
crash_kexec_post_notifiers is enabled. crash_smp_send_stop() is a weak
function, and it just call smp_send_stop(). Architecture codes should
override it so that kdump can work appropriately. This patch only
provides x86-specific version.
For Xen's PV kernel, just keep the current behavior.
NOTES:
- Right solution would be to place crash_smp_send_stop() before
__crash_kexec() invocation in all cases and remove smp_send_stop(), but
we can't do that until all architectures implement own
crash_smp_send_stop()
- crash_smp_send_stop()-like work is still needed by
machine_crash_shutdown() because crash_kexec() can be called without
entering panic()
Fixes: f06e5153f4ae (kernel/panic.c: add "crash_kexec_post_notifiers" option)
Link: http://lkml.kernel.org/r/20160810080948.11028.15344.stgit@sysi4-13.yrl.intra.hitachi.co.jp
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reported-by: Daniel Walker <dwalker@fifo99.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Xunlei Pang <xpang@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the DMA_ATTR_NO_WARN attribute on powerpc iommu code.
Link: http://lkml.kernel.org/r/1470092390-25451-3-git-send-email-mauricfo@linux.vnet.ibm.com
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-7-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-6-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-5-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Russell King - ARM Linux" <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-4-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Russell King - ARM Linux" <linux@arm.linux.org.uk>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-3-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
|
|
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
|
|
Show the real trap name when the kernel crashes.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Commit 4fe9e1d957e4 ("parisc: Drop bootmem and switch to memblock")
switched to the memblock allocator, but missed to zero-initialize the
newly allocated memblocks. This lead to crashes on some machines like
the rp3410.
Fixes: 4fe9e1d957e4 ("parisc: Drop bootmem and switch to memblock")
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
|
|
|
|
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.9:
API:
- The crypto engine code now supports hashes.
Algorithms:
- Allow keys >= 2048 bits in FIPS mode for RSA.
Drivers:
- Memory overwrite fix for vmx ghash.
- Add support for building ARM sha1-neon in Thumb2 mode.
- Reenable ARM ghash-ce code by adding import/export.
- Reenable img-hash by adding import/export.
- Add support for multiple cores in omap-aes.
- Add little-endian support for sha1-powerpc.
- Add Cavium HWRNG driver for ThunderX SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (137 commits)
crypto: caam - treat SGT address pointer as u64
crypto: ccp - Make syslog errors human-readable
crypto: ccp - clean up data structure
crypto: vmx - Ensure ghash-generic is enabled
crypto: testmgr - add guard to dst buffer for ahash_export
crypto: caam - Unmap region obtained by of_iomap
crypto: sha1-powerpc - little-endian support
crypto: gcm - Fix IV buffer size in crypto_gcm_setkey
crypto: vmx - Fix memory corruption caused by p8_ghash
crypto: ghash-generic - move common definitions to a new header file
crypto: caam - fix sg dump
hwrng: omap - Only fail if pm_runtime_get_sync returns < 0
crypto: omap-sham - shrink the internal buffer size
crypto: omap-sham - add support for export/import
crypto: omap-sham - convert driver logic to use sgs for data xmit
crypto: omap-sham - change the DMA threshold value to a define
crypto: omap-sham - add support functions for sg based data handling
crypto: omap-sham - rename sgl to sgl_tmp for deprecation
crypto: omap-sham - align algorithms on word offset
crypto: omap-sham - add context export/import stubs
...
|
|
Pull misc vfs updates from Al Viro:
"Assorted misc bits and pieces.
There are several single-topic branches left after this (rename2
series from Miklos, current_time series from Deepa Dinamani, xattr
series from Andreas, uaccess stuff from from me) and I'd prefer to
send those separately"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (39 commits)
proc: switch auxv to use of __mem_open()
hpfs: support FIEMAP
cifs: get rid of unused arguments of CIFSSMBWrite()
posix_acl: uapi header split
posix_acl: xattr representation cleanups
fs/aio.c: eliminate redundant loads in put_aio_ring_file
fs/internal.h: add const to ns_dentry_operations declaration
compat: remove compat_printk()
fs/buffer.c: make __getblk_slow() static
proc: unsigned file descriptors
fs/file: more unsigned file descriptors
fs: compat: remove redundant check of nr_segs
cachefiles: Fix attempt to read i_blocks after deleting file [ver #2]
cifs: don't use memcpy() to copy struct iov_iter
get rid of separate multipage fault-in primitives
fs: Avoid premature clearing of capabilities
fs: Give dentry to inode_change_ok() instead of inode
fuse: Propagate dentry down to inode_change_ok()
ceph: Propagate dentry down to inode_change_ok()
xfs: Propagate dentry down to inode_change_ok()
...
|
|
Pull nios2 update from Ley Foon Tan:
"Use of_property_read_bool() instead of open-coding it"
* tag 'nios2-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: use of_property_read_bool
|
|
Pull CRIS updates from Jesper Nilsson.
* tag 'cris-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: return of class_create should be considered
CRIS: defconfig: remove MTDRAM_ABS_POS
CRIS v32: remove some double unlocks
Fix typos
cris: migrate exception table users off module.h and onto extable.h
cris: v10: axisflashmap: remove unused ifdefs
cris: use generic io.h
cris: fix Kconfig mismatch when building with CONFIG_PCI
cris: cardbus: fix header include path
cris: add dev88_defconfig
cris: irq: stop loop from accessing array out of bounds
cris: fasttimer: fix mixed declarations and code compile warning
cris: intmem: fix pointer comparison compile warning
cris: intmem: fix device_initcall compile warning
|
|
Pull protection keys syscall interface from Thomas Gleixner:
"This is the final step of Protection Keys support which adds the
syscalls so user space can actually allocate keys and protect memory
areas with them. Details and usage examples can be found in the
documentation.
The mm side of this has been acked by Mel"
* 'mm-pkeys-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Update documentation
x86/mm/pkeys: Do not skip PKRU register if debug registers are not used
x86/pkeys: Fix pkeys build breakage for some non-x86 arches
x86/pkeys: Add self-tests
x86/pkeys: Allow configuration of init_pkru
x86/pkeys: Default to a restrictive init PKRU
pkeys: Add details of system call use to Documentation/
generic syscalls: Wire up memory protection keys syscalls
x86: Wire up protection keys system calls
x86/pkeys: Allocation/free syscalls
x86/pkeys: Make mprotect_key() mask off additional vm_flags
mm: Implement new pkey_mprotect() system call
x86/pkeys: Add fault handling for PF_PK page fault bit
|
|
Pull x86 updates from Thomas Gleixner:
"A pile of regression fixes and updates:
- address the fallout of the patches which made the cpuid - nodeid
relation permanent: Handling of invalid APIC ids and preventing
pointless warning messages.
- force eager FPU when protection keys are enabled. Protection keys
are not generating FPU exceptions so they cannot work with the lazy
FPU mechanism.
- prevent force migration of interrupts which are not part of the CPU
vector domain.
- handle the fact that APIC ids are not updated in the ACPI/MADT
tables on physical CPU hotplug
- remove bash-isms from syscall table generator script
- use the hypervisor supplied APIC frequency when running on VMware"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Make protection keys an "eager" feature
x86/apic: Prevent pointless warning messages
x86/acpi: Prevent LAPIC id 0xff from being accounted
arch/x86: Handle non enumerated CPU after physical hotplug
x86/unwind: Fix oprofile module link error
x86/vmware: Skip lapic calibration on VMware
x86/syscalls: Remove bash-isms in syscall table generator
x86/irq: Prevent force migration of irqs which are not in the vector domain
|
|
Merge the crypto tree to pull in vmx ghash fix.
|
|
Since BUILDTIME_EXTABLE_SORT is enabled, the exception table can move
into the read-only section.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Architecturally we need to keep __gp below 0x1000000.
But because of ftrace and tracepoint support, the RO_DATA_SECTION now gets much
bigger than it was before. By moving the linkage tables before RO_DATA_SECTION
we can avoid that __gp gets positioned at a too high address.
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Increase the initial kernel default page mapping size for 64-bit kernels to
64 MB and for 32-bit kernels to 32 MB.
Due to the additional support of ftrace, tracepoint and huge pages the kernel
size can exceed the sizes we used up to now.
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
|
|
This file was only including module.h for exception table related
functions. We've now separated that content out into its own file
"extable.h" so now move over to that and avoid all the extra header
content in module.h that we don't really need to compile this file.
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Our XSAVE features are divided into two categories: those that
generate FPU exceptions, and those that do not. MPX and pkeys do
not generate FPU exceptions and thus can not be used lazily. We
disable them when lazy mode is forced on.
We have a pair of masks to collect these two sets of features, but
XFEATURE_MASK_PKRU was added to the wrong mask: XFEATURE_MASK_LAZY.
Fix it by moving the feature to XFEATURE_MASK_EAGER.
Note: this only causes problem if you boot with lazy FPU mode
(eagerfpu=off) which is *not* the default. It also only affects
hardware which is not currently publicly available. It looks like
eager mode is going away, but we still need this patch applied
to any kernel that has protection keys and lazy mode, which is 4.6
through 4.8 at this point, and 4.9 if the lazy removal isn't sent
to Linus for 4.9.
Fixes: c8df40098451 ("x86/fpu, x86/mm/pkeys: Add PKRU xsave fields and data structures")
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20161007162342.28A49813@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Markus reported that he sees new warnings:
APIC: NR_CPUS/possible_cpus limit of 4 reached. Processor 4/0x84 ignored.
APIC: NR_CPUS/possible_cpus limit of 4 reached. Processor 5/0x85 ignored.
This comes from the recent persistant cpuid - nodeid changes. The code
which emits the warning has been called prior to these changes only for
enabled processors. Now it's called for disabled processors as well to get
the possible cpu accounting correct. So if the kernel is compiled for the
number of actual available/enabled CPUs and the BIOS reports disabled CPUs
as well then the above warnings are printed.
That's a pointless exercise as it only makes sense if there are more CPUs
enabled than the kernel supports.
Nake the warning conditional on enabled processors so we are back to the
state before these changes.
Fixes: 8f54969dc8d6 ("x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping")
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: linux-acpi@vger.kernel.org
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610071549330.19804@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Yinghai reported that the recent changes to make the cpuid - nodeid
relationship permanent causes a cpuid ordering regression on a system which
has 2apic enabled..
The reason is that the ACPI local APIC parser has no sanity check for
apicid 0xff, which is an invalid id. So a CPU id for this invalid local
APIC id is allocated and therefor breaks the cpuid ordering.
Add a sanity check to acpi_parse_lapic() which ignores the invalid id.
Fixes: 8f54969dc8d6 ("x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>,
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: douly.fnst@cn.fujitsu.com,
Cc: zhugh.fnst@cn.fujitsu.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>,
Cc: robert.moore@intel.com
Cc: linux-acpi@vger.kernel.org
Link: https://lkml.kernel.org/r/CAE9FiQVQx6FRXT-RdR7Crz4dg5LeUWHcUSy1KacjR+JgU_vGJg@mail.gmail.com
|
|
Merge updates from Andrew Morton:
- fsnotify updates
- ocfs2 updates
- all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (127 commits)
console: don't prefer first registered if DT specifies stdout-path
cred: simpler, 1D supplementary groups
CREDITS: update Pavel's information, add GPG key, remove snail mail address
mailmap: add Johan Hovold
.gitattributes: set git diff driver for C source code files
uprobes: remove function declarations from arch/{mips,s390}
spelling.txt: "modeled" is spelt correctly
nmi_backtrace: generate one-line reports for idle cpus
arch/tile: adopt the new nmi_backtrace framework
nmi_backtrace: do a local dump_stack() instead of a self-NMI
nmi_backtrace: add more trigger_*_cpu_backtrace() methods
min/max: remove sparse warnings when they're nested
Documentation/filesystems/proc.txt: add more description for maps/smaps
mm, proc: fix region lost in /proc/self/smaps
proc: fix timerslack_ns CAP_SYS_NICE check when adjusting self
proc: add LSM hook checks to /proc/<tid>/timerslack_ns
proc: relax /proc/<tid>/timerslack_ns capability requirements
meminfo: break apart a very long seq_printf with #ifdefs
seq/proc: modify seq_put_decimal_[u]ll to take a const char *, not char
proc: faster /proc/*/status
...
|
|
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
|
|
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The 64-bit DT changes are surprisingly small this time, we only add
two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive
quad-core Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
arm64: dts: berlin4ct: Add L2 cache topology
arm64: dts: berlin4ct: enable all wdt nodes unconditionally
arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
arm64: dts: apm: Add X-Gene SoC hwmon to device tree
arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
...
|
|
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
|
|
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
|
|
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms.
Nearly all of these are defconfig updates to enable new drivers or old
drivers still used on these 64-bit platforms.
Aside from that, we gain initial support for two set-top-box
platforms, both of which already have 32-bit support in arch/arm:
- Broadcom adds abstract support for the bcm7xxx/brcmstb platform,
presumably the respective dts files and more information will
follow at a later point.
- The ZTE ZX296718 SoC for set-top-boxes, a relative of the 32-bit
ZX296702 SoC that we already support"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: add ZTE ZX SoC family
arm64: defconfig: enable ZTE ZX related config
arm64: defconfig: enable common modules for power management
arm64: defconfig: enable meson I2C
arm64: defconfig: enable meson SPI as module
arm64: defconfig: enable meson WDT as modules
arm64: defconfig: enable HW random as module
arm64: defconfig: Enable SDHI and GPIO_REGULATOR
arm64: configs: enable PCIe driver for Aardvark
Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
arm64: defconfig: enable bluetooth supports as modules
arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
arm64: defconfig: Enable Hisi SAS and HNS
arm64: defconfig: Enable QDF2432 config options
arm64: sunxi: Kconfig: add essential pinctrl driver
arm64: defconfig: Add Renesas R-Car HSUSB driver support as module
arm64: Add Broadcom Set Top Box Kconfig entry point
arm64: defconfig: enable xhci-platform
|
Mugunthan V N
Andrew Lunn
David S. Miller
Jarod Wilson
Linus Torvalds
Iyappan Subramanian
Masahiro Yamada
Petr Mladek
Thomas Garnier
Hidehiro Kawai
Mauricio Faria de Oliveira
Jason Cooper
Helge Deller
Al Viro
Herbert Xu
Paul Gortmaker
Dave Hansen
Thomas Gleixner