aboutsummaryrefslogtreecommitdiffstats
path: root/arch (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-09-04MIPS: Octeon: Add support for accessing the boot vector.Steven J. Hill5-1/+334
Used by the Octeon watchdog driver to get the address of the firmware boot vector. Signed-off-by: Steven J. Hill <steven.hill@cavium.com> Acked-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: linux-watchdog@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17206/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Remove the arch/mips/lantiq/xway/reset.c implementationMartin Blumenstingl3-148/+2
The RCU register are now access through separates drivers. remove the last pieces of the old implementation. The GPHY reset bits are now set by the GPHY driver which registers a reboot notifier. The reboot is triggered by a syscon-reboot driver and the MIPS specific parts are done by the generic MIPS implementation in arch/mips/kernel/reset.c. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17131/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: remove old USB PHY initialisationHauke Mehrtens1-43/+0
This is now done in a PHY driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: martin.blumenstingl@googlemail.com Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17130/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04phy: Add an USB PHY driver for the Lantiq SoCs using the RCU moduleHauke Mehrtens1-18/+18
This driver starts the DWC2 core(s) built into the XWAY SoCs and provides the PHY interfaces for each core. The phy instances can be passed to the dwc2 driver, which already supports the generic phy interface. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Rob Herring <robh@kernel.org> Cc: martin.blumenstingl@googlemail.com Cc: john@phrozen.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17127/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: remove old GPHY loader codeHauke Mehrtens3-221/+0
The GPHY loader was replaced by a new more flexible driver. Remove the old driver. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: martin.blumenstingl@googlemail.com Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17129/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfdMartin Blumenstingl1-2/+4
Compared to the old xrx200_phy_fw driver the new version has multiple enhancements. The name of the firmware files does not have to be added to all .dts files anymore - one now configures the GPHY mode (FE or GE) instead. Each GPHY can now also boot separate firmware (thus mixing of GE and FE GPHYs is now possible). The new implementation is based on the RCU syscon-mfd and uses the reeset_controller framework instead of raw RCU register reads/writes. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Cc: john@phrozen.org Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17128/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: remove old reset controller implementationHauke Mehrtens1-68/+0
This code is now replaced by a reset controller in drivers/reset/reset- lantiq-rcu.c. The old code was never used anyway. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: martin.blumenstingl@googlemail.com Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17124/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Replace ltq_boot_select() with dummy implementation.Ralf Baechle1-5/+5
This will only be used until the last usage of ltq_boot_select() has been removed. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: remove ltq_reset_cause() and ltq_boot_select()Hauke Mehrtens3-34/+0
Do not export the ltq_reset_cause() and ltq_boot_select() function any more. ltq_reset_cause() was accessed by the watchdog driver before to see why the last reset happened, this is now done through direct access of the register over regmap. The bits in this register are anyway different between the xrx200 and the falcon SoC. ltq_boot_select() is not used any more and was used by the flash drivers to check if the system was booted from this flash type, now the drivers should depend on the device tree only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17126/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Convert the fpi bus driver to a platform_driverHauke Mehrtens2-45/+0
Instead of hacking the configuration of the FPI bus into the arch code add an own bus driver for this internal bus. The FPI bus is the main bus of the SoC. This bus driver makes sure the bus is configured correctly before the child drivers are getting initialized. This driver will probably also be used on different SoCs later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: john@phrozen.org Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17122/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Enable MFD_SYSCON to be able to use it for the RCU MFDMartin Blumenstingl1-0/+1
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17120/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: lantiq: Use of_platform_default_populate instead of __dt_register_busesMartin Blumenstingl1-1/+1
This allows populating syscon devices which are using "simple-mfd" instead of "simple-bus". Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: john@phrozen.org Cc: robh@kernel.org Cc: andy.shevchenko@gmail.com Cc: p.zabel@pengutronix.de Cc: kishon@ti.com Cc: mark.rutland@arm.com Cc: linux-mips@linux-mips.org Cc: linux-mtd@lists.infradead.org Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Cc: linux-spi@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17116/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: Remove unnecessary inclusions of linux/irqchip/mips-gic.hPaul Burton3-3/+0
linux/irqchip/mips-gic.h is included in a few files that don't actually use it at all. Remove these unnecessary inclusions in preparation for removing the header. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17048/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: VDSO: Avoid use of linux/irqchip/mips-gic.hPaul Burton1-4/+3
Our VDSO code makes use of macros from linux/irqchip/mips-gic.h to provide offsets to register values, but these are trivial offsets to the two 32 bit halves of a 64 bit value. Replace use of the macros with zero (ie. omit adding an offset) and the size of the low 32 bit of the value. This removes our need for linux/irqchip/mips-gic.h & prepares us for it to be removed. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17047/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04irqchip: mips-gic: Move gic_get_c0_*_int() to asm/mips-gic.hPaul Burton5-4/+32
The linux/irqchip/mips-gic.h header is now almost empty. Move the declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() & gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being able to delete the former header. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17046/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: Use mips_gic_present() in place of gic_presentPaul Burton5-23/+17
In preparation for removing the gic_present global variable, switch to using the mips_gic_present() function instead. For the most part this is a straightforward substitution. In cases which previously wrapped the GIC case in an #ifdef CONFIG_MIPS_GIC that #ifdef has been removed, since mips_gic_present() will return a compile-time constant false allowing the affected code to be optimised out anyway. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17044/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: VDSO: Drop gic_get_usm_range() usagePaul Burton1-10/+5
We don't really need gic_get_usm_range() to abstract discovery of the address of the GIC user-visible section now that we have access to its base address globally. Switch to calculating it ourselves, which will allow us to stop requiring the irqchip driver to care about a counter exposed to userland for use via the VDSO. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17040/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04irqchip: mips-gic: Move various definitions to the driverPaul Burton1-5/+0
Move the definitions of macros used to convert between hardware IRQ numbers & shared or local interrupt numbers into the irqchip driver, which is all that should ever need to care about them. Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17039/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: GIC: Move GIC_LOCAL_INT_* to asm/mips-gic.hPaul Burton1-0/+24
Move the definition of VP-local interrupts provided by the MIPS Global Interrupt Controller to the new asm/mips-gic.h header to be alongside the new accessor functions. Whilst at it, convert to an enum which lends itself more easily to expansion & documentation. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17037/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: Add __ioread64_copyPaul Burton3-1/+45
We currently have __ioread32_copy, __iowrite32_copy & __iowrite64_copy helpers in lib/iomap_copy.c. This patch adds __ioread64_copy to round out the set, allowing copies from I/O memory using 32 or 64 bit reads. [ralf@linux-mips.org: Changed to move all the code of this patch to be applied to arch/mips temporarily.] Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17025/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-04MIPS: CPS: Read GIC_VL_IDENT directly, not via irqchip driverPaul Burton1-1/+1
Rather than calling the gic_read_local_vp_id() function from the GIC irqchip driver, call read_gic_vl_ident() to read the GIC_VL_IDENT register directly. This will allow us to remove gic_read_local_vp_id() from the irqchip driver in a further patch, since that driver doesn't actually care about the register's value. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17023/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-09-01MIPS: Malta: Use new GIC accessor functionsPaul Burton1-3/+3
Use the accessor functions provided by asm/mips-gic.h rather than calling functions provided by the GIC irqchip driver, in preparation for those non-IRQ-related functions being removed from the irqchip driver. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: GIC: Introduce asm/mips-gic.h with accessor functionsPaul Burton2-0/+294
This patch introduces a new header providing accessor functions for the MIPS Global Interrupt Controller (GIC) mirroring those provided for the other 2 components of the MIPS Coherent Processing System (CPS) - the Coherence Manager (CM) & Cluster Power Controller (CPC). This header makes use of the new standardised CPS accessor macros where possible, but does require some custom accessors for cases where we have either a bit or a register per interrupt. A major advantage of this over the existing include/linux/irqchip/mips-gic.h definitions is that code performing accesses can become much simpler, for example this: gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) + GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr), (unsigned long)trig << GIC_INTR_BIT(intr)); ...can become simply: change_gic_trig(intr, trig); The accessors handle 32 vs 64 bit in the same way as for CM & CPC code, which means that GIC code will also not need to worry about the access size in most cases. They are also accessible outside of drivers/irqchip/irq-mips-gic.c which will allow for simplification in the use of the non-interrupt portions of the GIC (eg. counters) which currently require the interrupt controller driver to expose helper functions for access. This patch doesn't change any existing code over to use the new accessors yet, since a wholesale change would be invasive & difficult to review. Instead follow-on patches will convert code piecemeal to use this new header. The one change to existing code is to rename gic_base to mips_gic_base & make it global, in order to fit in with the naming expected by the standardised CPS accessor macros. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17020/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Don't use dma_cache_sync to implement fd_cacheflushChristoph Hellwig1-2/+2
The floppy drivers doesn't otherwise use the DMA API, so indirecting through it just for cache flushing in MIPS-specific code just call dma_cache_wback_inv directly. Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: iommu@lists.linux-foundation.org Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Michal Simek <monstr@monstr.eu> Cc: David Howells <dhowells@redhat.com> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: x86@kernel.org Cc: linux-mips@linux-mips.org Cc: linux-ia64@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-xtensa@linux-xtensa.org Cc: linux-sh@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/17183/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: generic: Bump default NR_CPUS to 16Paul Burton1-1/+1
In generic_defconfig set CONFIG_NR_CPUS to 16 rather than 2, which is a rather too low limit for many modern day MIPS systems. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16949/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: generic: Don't explicitly disable CONFIG_USB_SUPPORTPaul Burton1-1/+0
Leave CONFIG_USB_SUPPORT at its default, allowing board config fragments to make use of USB drivers without needing to override it & trigger warnings from merge_config.sh. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16948/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Make CONFIG_MIPS_MT_SMP default yPaul Burton6-4/+2
On systems that support MT ASE multithreading (ie. VPEs) we are very likely to want to include that support as default. Rather than setting it in various defconfigs, simply make CONFIG_MIPS_MT_SMP default y such that systems which select CONFIG_SYS_SUPPORTS_MULTITHREADING get it by default. As well as allowing us to remove the selection of CONFIG_MIPS_MT_SMP from various defconfigs, this also allows the generated generic defconfigs which derive from generic_defconfig to automatically gain support for MT ASE SMP when building for a suitable (pre-MIPSr6) ISA. For malta_kvm_guest_defconfig CONFIG_MIPS_MT_SMP is explicitly disabled since enabling SMP implicitly disables CONFIG_KVM_GUEST, which depends on CONFIG_BROKEN_ON_SMP. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16947/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Prevent direct use of generic_defconfigPaul Burton1-0/+13
Using generic_defconfig directly is unlikely to be what a user actually wants to do - it doesn't specify any particular ISA revision & it doesn't enable any board or driver support, resulting in a largely useless kernel. Prevent users from using it directly, printing a helpful message to point them in the right direction if they attempt to. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16946/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: NI 169445: Only include in 32r2el kernelsPaul Burton1-0/+3
The NI 169445 board uses a little endian MIPS32r2 CPU, and therefore including board support in kernels that are unable to run on such a CPU is pointless. Specify requirements in the board config fragment that cause the NI 169445 board support to only be included in generic kernels that target little endian MIPS32r2 CPUs. For example, NI 169445 support will be included when configuring using 32r2el_defconfig but not when using 64r6_defconfig. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Nathan Sullivan <nathan.sullivan@ni.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16945/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: SEAD-3: Only include in 32 bit kernels by defaultPaul Burton1-0/+2
The MIPS SEAD-3 development board has only ever been used with 32 bit CPUs, so including support for it in 64 bit kernels is wasteful since those kernels will never run on a SEAD-3. Specify a requirement in the SEAD-3 board config fragment that ensures the board support is only included in 32 bit kernels, by checking that CONFIG_32BIT=y. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16944/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: generic: Allow filtering enabled boards by requirementsPaul Burton2-2/+98
Up until now when configuring a generic kernel all board config fragments have been merged by default unless boards are explicitly selected by the user specifying BOARDS=. In many cases this is sub-optimal, since some boards don't make sense to include in some kernels. For example the MIPS SEAD-3 development board has only ever been used with 32 bit CPUs, so including support for the SEAD-3 in a 64 bit kernel is wasteful. This patch introduces support for specifying requirements in board config fragments, using comments formatted like so: # require CONFIG_BLA=y For example the SEAD-3 board could specify that it should only be merged for 32 bit kernels using a requirement line like the following: # require CONFIG_32BIT=y A new generic-board-config.sh script is introduced to handle selecting the board config fragments to merge & calling merge_config.sh to merge them. In order to allow requirements to check Kconfig symbols that are implicitly selected, rather than explicitly specified by generic_defconfig or one of the ISA config fragments, an intermediate .config file is saved & used as a reference when checking requirements. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16943/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Detect CPUs in secondary clustersPaul Burton1-29/+51
As a first step towards supporting multi-cluster systems, detect cores & VPs in secondary clusters & record their cluster information in the cpu_data array. The "VP topology" line printed during boot is extended to display multiple clusters. On a single cluster it shows output like the following: VP topology: {4,4} This would indicate a system with 2 cores which each contain 4 VPs. We extend this to cover multiple clusters in a natural way: VP topology: {4,4},{2,2} This would indicate a system with 2 clusters. The first cluster contains 2 cores which each contain 4 VPs. The second cluster contains 2 cores which each contain 2 VPs. Actually booting these cores & VPs is left to further patches once other pieces are in place. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17017/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Cluster support for topology functionsPaul Burton7-48/+136
Modify the functions we use to read information about the topology of the system (the number of cores, VPs & IOCUs that it contains) in order to take into account multiple clusters, and provide a new function to determine the number of clusters in the system. Users of these functions are modified only such that they continue to build successfully - having them actually handle multiple clusters is left to further patches. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17016/ Patchwork: https://patchwork.linux-mips.org/patch/17218/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Have asm/mips-cps.h include CM & CPC headersPaul Burton19-29/+27
With Coherence Manager (CM) 3.5 information about the topology of the system, which has previously only been available through & accessed from the CM, is now also provided by the Cluster Power Controller (CPC). This includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG. In preparation for adjusting functions such as mips_cm_numcores(), which have previously only needed to access the CM, to also access the CPC this patch modifies the way we use the various CPS headers. Rather than having users include asm/mips-cm.h or asm/mips-cpc.h individually we instead have users include asm/mips-cps.h which in turn includes asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access to both CM & CPC registers by including one header, and most importantly it makes asm/mips-cps.h an ideal location for helper functions which need to access the various components of the CPS. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17015/ Patchwork: https://patchwork.linux-mips.org/patch/17217/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: SMP: Allow boot_secondary SMP op to return errorsPaul Burton14-15/+37
Allow the boot_secondary SMP op to return an error to __cpu_up(), which will in turn return it to its caller. This will allow SMP implementations to return errors quickly in cases they they know have failed, rather than relying upon __cpu_up() eventually timing out waiting for the cpu_running completion. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17014/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CM: Add cluster & block args to mips_cm_lock_other()Paul Burton4-18/+58
With CM >= 3.5 we have the notion of multiple clusters & can access their CM, CPC & GIC registers via the apporpriate redirect/other register blocks. In order to allow for this introduce cluster & block arguments to mips_cm_lock_other() which configures the redirect/other region to point at the appropriate cluster, core, VP & register block. Since we now have 4 arguments to mips_cm_lock_other() & a common use is likely to be to target the cluster, core & VP corresponding to a particular Linux CPU number we also add a new mips_cm_lock_other_cpu() helper function which handles that without the caller needing to manually pull out the cluster, core & VP numbers. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17013/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Add CPU cluster number accessorsPaul Burton2-0/+21
Introduce cpu_cluster() & cpu_set_cluster() accessor functions in the same vein as cpu_core(), cpu_vpe_id() & their set variants. These will be used in further patches to allow users to get or set a CPUs cluster number. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17012/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Unify checks for sibling CPUsPaul Burton3-11/+26
Up until now we have open-coded checks for whether CPUs are siblings, with slight variations on whether we consider the package ID or not. This will only get more complex when we introduce cluster support, so in preparation for that this patch introduces a cpus_are_siblings() function which can be used to check whether or not 2 CPUs are siblings in a consistent manner. By checking globalnumber with the VP ID masked out this also has the neat side effect of being ready for multi-cluster systems already. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17011/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Store core & VP IDs in GlobalNumber-style variablePaul Burton2-26/+35
This patch modifies the way we store core & VP IDs such that we store them in a single 32 bit integer whose format matches that of the MIPSr6 GlobalNumber register. Whereas we have previously stored core & VP IDs in separate fields, storing them in a single GlobalNumber-like field: 1) Reduces the size of struct cpuinfo_mips by 4 bytes, and will allow it to not grow when cluster support is added. 2) Gives us a natural place to store cluster number, which matches up with what the architecture provides. 3) Will be useful in the future as a parameter to the MIPSr6 GINVI instruction to specify a target CPU whose icache that instruction should operate on. The cpu_set*() accessor functions are moved out of the asm/cpu-info.h header in order to allow them to use the WARN_ON macro, which is unusable in asm/cpu-info.h due to include ordering. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17010/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Abstract CPU core & VP(E) ID access through accessor functionsPaul Burton15-45/+70
We currently have fields in struct cpuinfo_mips for the core & VP(E) ID of a particular CPU, and various pieces of code directly access those fields. This patch abstracts such access by introducing accessor functions cpu_core(), cpu_set_core(), cpu_vpe_id() & cpu_set_vpe_id() and having code that needs to access these values call those functions rather than directly accessing the struct cpuinfo_mips fields. This prepares us for changes to the way in which those values are stored in later patches. The cpu_vpe_id() function is introduced even though we already had a cpu_vpe_id() macro for a couple of reasons: 1) It's more consistent with the core, and future cluster, accessors. 2) It ensures a sensible return type without explicit casts. 3) It's generally preferable to use functions rather than macros. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17009/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Use GlobalNumber macros rather than magic numbersPaul Burton1-2/+2
We now have definitions for the GlobalNumber register in asm/mipsregs.h, so use them in place of magic numbers in cps-vec.S. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17008/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: Add accessor & bit definitions for GlobalNumberPaul Burton1-0/+13
MIPSr6 introduces a GlobalNumber register, which is required when VPs are implemented (ie. when multi-threading is supported) but otherwise optional. The register contains sufficient information to uniquely identify a VP within a system using its cluster number, core number & VP ID. In preparation for using this register & its fields, introduce an accessor macro for it & define its various bits with the typical style preprocessor macros. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17007/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Add CM/CPC 3.5 register definitionsPaul Burton2-7/+69
Introduce definitions & accessors for a selection of Coherence Manager (CM) & Cluster Power Controller (CPC) registers that are new with CM v3.5 & the MIPS I6500. These are primarily registers that will be used in supporting multiple CPU clusters. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17006/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Use change_*, set_* & clear_* where appropriatePaul Burton3-21/+8
Make use of the new change_*, set_* & clear_* accessor functions for CPS (CM, CPC & GIC) registers where doing so makes the code easier to read or shortens it without adversely affecting readability. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17005/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPS: Introduce register modify (set/clear/change) accessorsPaul Burton1-1/+22
For read-write registers introduce accessor functions that simplify the task of modifying a subset of bits within the register. set_* functions set bits to 1, clear_* functions clear bits to 0 & change_* functions set bits specified in a mask to an arbitrary value. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17004/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPC: Use BIT/GENMASK for register fields, order & drop shiftsPaul Burton4-42/+49
Tidy up asm/mips-cpc.h in a similar way to what "MIPS: CM: Use BIT/GENMASK for register fields, order & drop shifts" did for asm/mips-cm.h. We use BIT() & GENMASK() to simplify the definition of register fields, drop the _SHF definitions since that information can be found in the _MSK ones, and then drop the _MSK suffix. Fields definitions are moved to be next to the appropriate register definition, making it easier to link the two & keep everything ordered by register address. Comments are added including the name of each register & a brief description of its purpose which helps to understand what registers are for, link them back to hardware documentation or grep for them. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17003/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30MIPS: CPC: Use common CPS accessor generation macrosPaul Burton1-41/+22
Switch the MIPS Cluster Power Controller (CPC) accessor functions to be generated by the new common Coherent Processing System (CPS) macros shared with the Coherence Manager (CM). Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17002/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-29MIPS: CM: Use BIT/GENMASK for register fields, order & drop shiftsPaul Burton8-239/+188
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h when declaring macros corresponding to register fields. This patch modifies our definitions to do so. The *_SHF definitions are removed entirely - they duplicate information found in the masks, are infrequently used & can be replaced with use of __ffs() where needed. The *_MSK definitions then lose their _MSK suffix which is now somewhat redundant, and users are modified to match. The field definitions are moved to follow the appropriate register's accessor functions, which helps to keep the field definitions in order & to find the appropriate fields for a given register. Whilst here a comment is added describing each register & including its name, which is helpful both for linking the register back to hardware documentation & for grepping purposes. This also cleans up a couple of issues that became obvious as a result of making the changes described above: - We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony copy of that named GCR_RESET_EXT_BASE - a register which does not exist. The bad definitions were added by commit 497e803ebf98 ("MIPS: smp-cps: Ensure secondary cores start with EVA disabled") and made use of from boot_core(), which is now modified to use the GCR_Cx_RESET_EXT_BASE definitions. - We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly define this as inFo rather than inGo. Now that we don't duplicate field information between _SHF & _MSK definitions, and keep the fields next to the register accessors, it will be much easier to spot & prevent any similar oddities being introduced in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Thomas Gleixner <tglx@linutronix.de Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17001/ Patchwork: https://patchwork.linux-mips.org/patch/17216/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-29MIPS: CM: Specify register size when generating accessorsPaul Burton3-115/+135
Some CM registers are always 32 bits, or at least only use bits in the lower 32 bits of the register. For these registers it is wasteful for us to generate accessors which bother to check mips_cm_is64 & perform 64 bit accesses. This patch modifies the accessor generation to take into account the size of the register, and for 32 bit registers we generate accessors which only ever perform 32 bit accesses. For 64 bit registers we either perform a 64 bit access or two 32 bit accesses, depending upon the value of mips_cm_is64. Doing this saves us ~1.5KiB of code in a generic 64r6el kernel, and perhaps more importantly simplifies various code paths. This removes the read64_gcr_* accessors, so mips_cm_error_report() is modified to stop using them & instead use the regular read_gcr_* accessors which will return 64 bit values from the 64 bit registers. The new accessor macros are placed in asm/mips-cps.h such that they can be shared by CPC & GIC code in later patches. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/17000/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-29MIPS: CM: Rename mips_cm_base to mips_gcr_basePaul Burton2-8/+8
We currently have a mips_cm_base variable which holds the base address of the Coherence Manager (CM) Global Configuration Registers (GCRs), and accessor functions which use the GCR in their names. This works fine, but gets in the way of sharing the code to generate the accessor functions with other blocks (ie. CPC & GIC) because that code would then need to separately handle the name of the base address variable & the name used in the accessor functions. In order to prepare for sharing the accessor generation code between CM, CPC & GIC code this patch renames mips_cm_base to mips_gcr_base such that the "gcr" portion is common to both the base address variable & the accessor function names. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16999/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.