| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
|
|
Commit 16da306849d0 ("um: kill pfn_t") introduced a compile warning for
defconfig (SUBARCH=i386):
arch/um/kernel/skas/mmu.c:38:206:
warning: right shift count >= width of type [-Wshift-count-overflow]
Aforementioned patch changes the definition of the phys_to_pfn() macro
from
((pfn_t) ((p) >> PAGE_SHIFT))
to
((p) >> PAGE_SHIFT)
This effectively changes the phys_to_pfn() expansion's type from
unsigned long long to unsigned long.
Through the callchain init_stub_pte() => mk_pte(), the expansion of
phys_to_pfn() is (indirectly) fed into the 'phys' argument of the
pte_set_val(pte, phys, prot) macro, eventually leading to
(pte).pte_high = (phys) >> 32;
This results in the warning from above.
Since UML only deals with 32 bit addresses, the upper 32 bits from
'phys' used to be always zero anyway. Also, all page protection flags
defined by UML don't use any bits beyond bit 9. Since the contents of a
PTE are defined within architecture scope only, the ->pte_high member
can be safely removed.
Remove the ->pte_high member from struct pte_t.
Rename ->pte_low to ->pte.
Adapt the pte helper macros in arch/um/include/asm/page.h.
Noteworthy is the pte_copy() macro where a smp_wmb() gets dropped. This
write barrier doesn't seem to be paired with any read barrier though and
thus, was useless anyway.
Fixes: 16da306849d0 ("um: kill pfn_t")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 944d9fec8d7a ("hugetlb: add support for gigantic page allocation
at runtime") has added the runtime gigantic page allocation via
alloc_contig_range(), making this support available only when CONFIG_CMA
is enabled. Because it doesn't depend on MIGRATE_CMA pageblocks and the
associated infrastructure, it is possible with few simple adjustments to
require only CONFIG_MEMORY_ISOLATION instead of full CONFIG_CMA.
After this patch, alloc_contig_range() and related functions are
available and used for gigantic pages with just CONFIG_MEMORY_ISOLATION
enabled. Note CONFIG_CMA selects CONFIG_MEMORY_ISOLATION. This allows
supporting runtime gigantic pages without the CMA-specific checks in
page allocator fastpaths.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One of the randconfig build failed with the error:
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_mm':
arch/m32r/kernel/smp.c:283:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_flush_tlb_page':
arch/m32r/kernel/smp.c:353:20: error: subscripted value is neither array nor pointer nor vector
mmc = &mm->context[cpu_id];
^
arch/m32r/kernel/smp.c: In function 'smp_invalidate_interrupt':
arch/m32r/kernel/smp.c:479:41: error: subscripted value is neither array nor pointer nor vector
unsigned long *mmc = &flush_mm->context[cpu_id];
It turned out that CONFIG_SMP was defined but CONFIG_MMU was not
defined. But arch/m32r/include/asm/mmu.h only defines mm_context_t as
an array when both CONFIG_SMP and CONFIG_MMU are defined. And
arch/m32r/kernel/smp.c is always using context as an array. So without
MMU SMP can not work.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull arm64 fixes from Will Deacon:
"Nothing particularly interesting here, but all important fixes
nonetheless:
- Add missing PAN toggling in the futex code
- Fix missing #include that briefly caused issues in -next
- Allow changing of vmalloc permissions with set_memory_* (used by
bpf)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: asm: Explicitly include linux/personality.h in asm/page.h
arm64: futex.h: Add missing PAN toggling
arm64: allow vmalloc regions to be set with set_memory_*
|
|
The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
asm/page.h uses READ_IMPLIES_EXEC from linux/personality.h but does not
explicitly include it causing build failures in -next where whatever was
causing it to be implicitly included has changed to remove that
inclusion. Add an explicit inclusion to fix this.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: moved #include inside #ifndef __ASSEMBLY__ block]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
futex.h's futex_atomic_cmpxchg_inatomic() does not use the
__futex_atomic_op() macro and needs its own PAN toggling. This was missed
when the feature was implemented.
Fixes: 338d4f49d6f ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The range of set_memory_* is currently restricted to the module address
range because of difficulties in breaking down larger block sizes.
vmalloc maps PAGE_SIZE pages so it is safe to use as well. Update the
function ranges and add a comment explaining why the range is restricted
the way it is.
Suggested-by: Laura Abbott <labbott@fedoraproject.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
|
|
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
API:
- algif_hash needs to wait for init operations to complete.
- The has_key setting for shash was always true.
Algorithms:
- Add missing selections of CRYPTO_HASH.
- Fix pkcs7 authentication.
Drivers:
- Fix stack alignment bug in chacha20-ssse3.
- Fix performance regression in caam due to incorrect setting.
- Fix potential compile-only build failure of stm32"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: atmel-aes - remove calls of clk_prepare() from atomic contexts
crypto: algif_hash - wait for crypto_ahash_init() to complete
crypto: shash - Fix has_key setting
hwrng: stm32 - Fix dependencies for !HAS_IOMEM archs
crypto: ghash,poly1305 - select CRYPTO_HASH where needed
crypto: chacha20-ssse3 - Align stack pointer to 64 bytes
PKCS#7: Don't require SpcSpOpusInfo in Authenticode pkcs7 signatures
crypto: caam - make write transactions bufferable on PPC platforms
|
|
vexpress fixes for v4.5
Couple of minor fixes for vexpress platforms:
1. Add missing of_node_put in vexpress config bus
2. Add missing DMA-330 abort interrupt on Juno platforms
* tag 'vexpress-for-v4.5/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.5 (part 1)
- Fix dts on buffalo linksations machines (gpios and leds)
- Fix dts partition node according to new binding introduced in v4.5
* tag 'mvebu-fixes-4.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: gpio pin fixes for linkstation lswtgl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxl
ARM: mvebu: ix4-300d: Add compatible property to "partitions" node
ARM: mvebu: kirkwood: Add compatible property to "partitions" node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
First fixes for 4.5. Only DT changes:
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt
ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0
ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0
ARM: dts: at91: at91sam9n12ek: fix panel compatible string
ARM: dts: at91: sama5d4: fix instance id of DBGU
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This platform recently moved to multi-platform, so missed the global
fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs
instead of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This platform was recently added, so missed the global fixup by
commit e32465429490 ("ARM: use "depends on" for SoC configs instead
of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This newly added code missed the global fixup by commit 75305275a721
("ARM: use const and __initconst for smp_operations"). So fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This newly added code missed the global fixup by commit 75305275a721
("ARM: use const and __initconst for smp_operations"). So fix it now.
Also, add missing "static" qualifier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The DMA-330 has an "irq_abort" interrupt line on which it signals faults
separately from the "irq[n:0]" channel interrupts. On Juno, this is
wired up to SPI 92; add it to the DT so that DMAC faults are correctly
reported for the driver to reset the thing, rather than leaving it
locked up and waiting to time out.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Pull MIPS fix from Ralf Baechle:
"Just a single revert for a patch which I had upstreamed out of
sequence"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Revert "MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function"
|
|
Pull x86 fixes from Thomas Gleixner:
"A bit on the largish side due to a series of fixes for a regression in
the x86 vector management which was introduced in 4.3. This work was
started in December already, but it took some time to fix all corner
cases and a couple of older bugs in that area which were detected
while at it
Aside of that a few platform updates for intel-mid, quark and UV and
two fixes for in the mm code:
- Use proper types for pgprot values to avoid truncation
- Prevent a size truncation in the pageattr code when setting page
attributes for large mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/pat: Avoid truncation when converting cpa->numpages to address
x86/mm: Fix types used in pgprot cacheability flags translations
x86/platform/quark: Print boundaries correctly
x86/platform/UV: Remove EFI memmap quirk for UV2+
x86/platform/intel-mid: Join string and fix SoC name
x86/platform/intel-mid: Enable 64-bit build
x86/irq: Plug vector cleanup race
x86/irq: Call irq_force_move_complete with irq descriptor
x86/irq: Remove outgoing CPU from vector cleanup mask
x86/irq: Remove the cpumask allocation from send_cleanup_vector()
x86/irq: Clear move_in_progress before sending cleanup IPI
x86/irq: Remove offline cpus from vector cleanup
x86/irq: Get rid of code duplication
x86/irq: Copy vectormask instead of an AND operation
x86/irq: Check vector allocation early
x86/irq: Reorganize the search in assign_irq_vector
x86/irq: Reorganize the return path in assign_irq_vector
x86/irq: Do not use apic_chip_data.old_domain as temporary buffer
x86/irq: Validate that irq descriptor is still active
x86/irq: Fix a race in x86_vector_free_irqs()
...
|
|
Pull perf fixes from Thomas Gleixner:
"This is much bigger than typical fixes, but Peter found a category of
races that spurred more fixes and more debugging enhancements. Work
started before the merge window, but got finished only now.
Aside of that this contains the usual small fixes to perf and tools.
Nothing particular exciting"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
perf: Remove/simplify lockdep annotation
perf: Synchronously clean up child events
perf: Untangle 'owner' confusion
perf: Add flags argument to perf_remove_from_context()
perf: Clean up sync_child_event()
perf: Robustify event->owner usage and SMP ordering
perf: Fix STATE_EXIT usage
perf: Update locking order
perf: Remove __free_event()
perf/bpf: Convert perf_event_array to use struct file
perf: Fix NULL deref
perf/x86: De-obfuscate code
perf/x86: Fix uninitialized value usage
perf: Fix race in perf_event_exit_task_context()
perf: Fix orphan hole
perf stat: Do not clean event's private stats
perf hists: Fix HISTC_MEM_DCACHELINE width setting
perf annotate browser: Fix behaviour of Shift-Tab with nothing focussed
perf tests: Remove wrong semicolon in while loop in CQM test
perf: Synchronously free aux pages in case of allocation failure
...
|
|
Pull ARM fixes from Russell King:
"Just one fix for a -fstack-protector-strong problem from Kees Cook,
and adding the new copy_file_range syscall"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: wire up copy_file_range() syscall
ARM: 8500/1: fix atags_to_fdt with stack-protector-strong
|
|
Pull powerpc fixes from Michael Ellerman:
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
* tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup _HPAGE_CHG_MASK
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
powerpc/eeh: Fix PE location code
powerpc/mm: Allow user space to map rtas_rmo_buf
powerpc: Remove newly added extra definition of pmd_dirty
powerpc: Simplify module TOC handling
powerpc: Wire up copy_file_range() syscall
|
|
Pull s390 updates from Martin Schwidefsky:
"An optimization for irq-restore, the SSM instruction is quite a bit
slower than an if-statement and a STOSM.
The copy_file_range system all is added.
Cleanup for PCI and CIO.
And a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: update measurement characteristics
s390/cio: ensure consistent measurement state
s390/cio: fix measurement characteristics memleak
s390/zcrypt: Fix cryptographic device id in kernel messages
s390/pci: remove iomap sanity checks
s390/pci: set error state for unusable functions
s390/pci: fix bar check
s390/pci: resize iomap
s390/pci: improve ZPCI_* macros
s390/pci: provide ZPCI_ADDR macro
s390/pci: adjust IOMAP_MAX_ENTRIES
s390/numa: move numa_init_late() from device to arch_initcall
s390: remove all usages of PSW_ADDR_INSN
s390: remove all usages of PSW_ADDR_AMODE
s390: wire up copy_file_range syscall
s390: remove superfluous memblock_alloc() return value checks
s390/numa: allocate memory with correct alignment
s390/irqflags: optimize irq restore
s390/mm: use TASK_MAX_SIZE where applicable
|
|
There are a couple of nasty truncation bugs lurking in the pageattr
code that can be triggered when mapping EFI regions, e.g. when we pass
a cpa->pgd pointer. Because cpa->numpages is a 32-bit value, shifting
left by PAGE_SHIFT will truncate the resultant address to 32-bits.
Viorel-Cătălin managed to trigger this bug on his Dell machine that
provides a ~5GB EFI region which requires 1236992 pages to be mapped.
When calling populate_pud() the end of the region gets calculated
incorrectly in the following buggy expression,
end = start + (cpa->numpages << PAGE_SHIFT);
And only 188416 pages are mapped. Next, populate_pud() gets invoked
for a second time because of the loop in __change_page_attr_set_clr(),
only this time no pages get mapped because shifting the remaining
number of pages (1048576) by PAGE_SHIFT is zero. At which point the
loop in __change_page_attr_set_clr() spins forever because we fail to
map progress.
Hitting this bug depends very much on the virtual address we pick to
map the large region at and how many pages we map on the initial run
through the loop. This explains why this issue was only recently hit
with the introduction of commit
a5caa209ba9c ("x86/efi: Fix boot crash by mapping EFI memmap
entries bottom-up at runtime, instead of top-down")
It's interesting to note that safe uses of cpa->numpages do exist in
the pageattr code. If instead of shifting ->numpages we multiply by
PAGE_SIZE, no truncation occurs because PAGE_SIZE is a UL value, and
so the result is unsigned long.
To avoid surprises when users try to convert very large cpa->numpages
values to addresses, change the data type from 'int' to 'unsigned
long', thereby making it suitable for shifting by PAGE_SHIFT without
any type casting.
The alternative would be to make liberal use of casting, but that is
far more likely to cause problems in the future when someone adds more
code and fails to cast properly; this bug was difficult enough to
track down in the first place.
Reported-and-tested-by: Viorel-Cătălin Răpițeanu <rapiteanu.catalin@gmail.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110131
Link: http://lkml.kernel.org/r/1454067370-10374-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Get rid of the 'onln' obfuscation.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When calling intel_alt_er() with .idx != EXTRA_REG_RSP_* we will not
initialize alt_idx and then use this uninitialized value to index an
array.
When that is not fatal, it can result in an infinite loop in its
caller __intel_shared_reg_get_constraints(), with IRQs disabled.
Alternative error modes are random memory corruption due to the
cpuc->shared_regs->regs[] array overrun, which manifest in either
get_constraints or put_constraints doing weird stuff.
Only took 6 hours of painful debugging to find this. Neither GCC nor
Smatch warnings flagged this bug.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: ae3f011fc251 ("perf/x86/intel: Fix SLM MSR_OFFCORE_RSP1 valid_mask")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This was wrongly updated by commit 7aa9a23c69ea ("powerpc, thp: remove
infrastructure for handling splitting PMDs") during the last merge
window. Fix it up.
This could lead to incorrect behaviour in THP and/or mprotect(), at a
minimum.
Fixes: 7aa9a23c69ea ("powerpc, thp: remove infrastructure for handling splitting PMDs")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 7a7868326d77 ("powerpc/perf: Add an explict flag indicating
presence of SLOT field") introduced the PPMU_HAS_SSLOT flag to remove
the assumption that MMCRA[SLOT] was present when PPMU_ALT_SIPR was not
set.
That commit's changelog also mentions that Power8 does not support
MMCRA[SLOT]. However when the Power8 PMU support was merged, it
errnoeously included the PPMU_HAS_SSLOT flag.
So remove PPMU_HAS_SSLOT from the Power8 flags.
mpe: On systems where MMCRA[SLOT] exists, the field occupies bits 37:39
(IBM numbering). On Power8 bit 37 is reserved, and 38:39 overlap with
the high bits of the Threshold Event Counter Mantissa. I am not aware of
any published events which use the threshold counting mechanism, which
would cause the mantissa bits to be set. So in practice this bug is
unlikely to trigger.
Fixes: e05b9b9e5c10 ("powerpc/perf: Power8 PMU support")
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull virtio tests and fixes from Michael Tsirkin:
"This fixes existing tests broken by barrier rework, and adds some new
tests.
Plus, there's a fix for an old bug in virtio-pci"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: add ringtest utilities
sh: fix smp_store_mb for !SMP
tools/virtio: use virt_xxx barriers
virtio_pci: fix use after free on release
|
|
This reverts commit 5bdb102b3f9785cb88467bc7c75fa0f5cacc8dc5.
Brian Norris <computersforpeace@gmail.com> is reporting:
Ralf,
Please revert this and send it to Linus (or else, I can send it myself).
This is causing build failures, because I didn't take the rest of
Simon's series yet.
drivers/mtd/bcm63xxpart.c: In function 'bcm63xx_parse_cfe_partitions':
drivers/mtd/bcm63xxpart.c:93:2: error: implicit declaration of function
'bcm63xx_nvram_get_psi_size' [-Werror=implicit-function-declaration]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
References: https://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20160126191607.GA111152%40google.com
|
|
Pull arm64 fixes from Will Deacon:
"The main thing here is to get us booting under qemu again after it
turned out that not all of the PMU registers are emulated there,
causing us to die early in boot.
- Ensure we don't access PMU registers of the PMU is not implemented
(fixes booting under QEMU)
- Fix BUG_ON triggered during module loading with DEBUG_SET_MODULE_RONX
- Ensure the kasan zero page is read-only
- Hide __efistub_ symbol aliases from kallsyms, since they otherwise
confuse the backtrace code
- Ensure !PTE_WRITE kernel ptes are marked as read-only
- defconfig updates based on requests and patches on the list
- Other minor fixes (typos, build system)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: avoid calling apply_to_page_range on empty range
arm64: defconfig: updates for 4.5
arm64: errata: Add -mpc-relative-literal-loads to build flags
Eliminate the .eh_frame sections from the aarch64 vmlinux and kernel modules
arm64: Fix an enum typo in mm/dump.c
arm64: Honour !PTE_WRITE in set_pte_at() for kernel mappings
arm64: kernel: fix architected PMU registers unconditional access
arm64: kasan: ensure that the KASAN zero page is mapped read-only
arm64: hide __efistub_ aliases from kallsyms
|
|
Pull KVM fixes from Paolo Bonzini:
"s390 and POWER bug fixes, plus enabling the KVM-VFIO interface on
s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM doc: Fix KVM_SMI chapter number
KVM: s390: fix memory overwrites when vx is disabled
KVM: s390: Enable the KVM-VFIO device
KVM: s390: fix guest fprs memory leak
KVM: PPC: Fix ONE_REG AltiVec support
KVM: PPC: Increase memslots to 512
KVM: PPC: Book3S PR: Remove unused variable 'vcpu_book3s'
KVM: PPC: Fix emulation of H_SET_DABR/X on POWER8
KVM: PPC: Book3S HV: Handle unexpected traps in guest entry/exit code better
|
|
Add the copy_file_range() syscall to ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix CPSW EMAC pinmux
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix UART3 pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Setup USB2 to act in "HOST" mode by default.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix SB-SOM EEPROM I2C address
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
|
|
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec5047a ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
Linus Torvalds
Nicolai Stange
Vlastimil Babka
Sudip Mukherjee
Dinh Nguyen
Linus Walleij
Mark Brown
James Morse
Ard Biesheuvel
Olof Johansson
Jon Hunter
Masahiro Yamada
Robin Murphy
Matt Fleming
Peter Zijlstra
Aneesh Kumar K.V
Madhavan Srinivasan
Ralf Baechle
Russell King
Dmitry Lifshitz
Adam Ford
Grygorii Strashko
Nicolas Ferre
Alexandre Belloni
Wenyou Yang