| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We need to map the gap between 0x00000000 and __MEMORY_START in the PMB,
as well as RAM.
With this change my 7785LCR board can switch to 32bit MMU mode at
runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Eventually we'll have complete control over what physical memory gets
mapped where and we can probably do other interesting things. For now
though, when the MMU is in 32-bit mode, we map physical memory into the
P1 and P2 virtual address ranges with the same semantics as they have in
29-bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Unfortunately, at the time during in boot when we want to be setting up
the PMB entries, the kmem subsystem hasn't been initialised.
We now match pmb_map slots with pmb_entry_list slots. When we find an
empty slot in pmb_map, we set the bit, thereby acquiring the
corresponding pmb_entry_list entry. There is a benefit in using this
static array of struct pmb_entry's; we don't need to acquire any locks
in order to traverse the list of struct pmb_entry's.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There's no need to export the internal PMB functions for allocating,
freeing and modifying PMB entries, etc. This way we can restrict the
interface for PMB.
Also remove the static from pmb_init() so that we have more freedom in
setting up the initial PMB entries and turning on MMU 32bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
CONFIG_PMB will eventually allow the MMU to be switched between 29-bit
and 32-bit mode dynamically at runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
To allow the MMU to be switched between 29bit and 32bit mode at runtime
some constants need to swapped for functions that return a runtime
value.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Replace the use of PHYSADDR() with __pa(). PHYSADDR() is based on the
idea that all addresses in P1SEG are untranslated, so we can access an
address's physical page as an offset from P1SEG. This doesn't work for
CONFIG_PMB/CONFIG_PMB_FIXED because pages in P1SEG and P2SEG are used
for PMB mappings and so can be translated to any physical address.
Likewise, replace a P1SEGADDR() use with virt_to_phys().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Simplify set_pmb_entry() by removing the possibility of not finding a
free slot in the PMB. Instead we now allocate a slot in pmb_alloc() so
that if there are no free slots we fail at allocation time, rather than
in set_pmb_entry().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - print debug data when testing AUX IRQ delivery
Input: libps2 - fix dependancy on i8042
Input: fix rx51 board keymap
Input: ad7879 - pass up error codes from probe functions
Input: xpad - add BigBen Interactive XBOX 360 Controller
Input: rotary_encoder - fix relative axis support
Input: sparkspkr - move remove() functions to .devexit.text
Input: wistron_btns - add DMI entry for Medion WIM2030 laptop
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: convert to GENERIC_HARDIRQS_NO__DO_IRQ
Blackfin: drop all simple-gpio board resources
Blackfin: fix framebuffer mmap bug for nommu
Blackfin: includecheck fix: mach-bf548, ezkit.c
Blackfin: drop cs_change_per_word setting
Blackfin: bf533-ezkit: convert to physmap/jedec_probe
Blackfin: convert adv7393 resources to new i2c framework
Blackfin: fix missed cache config renames
Blackfin: cplbinfo: drop d_path() hacks
Blackfin: asm/irq.h: pull in mach/anomaly.h for anomaly defines
Blackfin: BF51x: add PTP MMR defines
Blackfin: mass clean up of copyright/licensing info
Blackfin: convert to use arch_gettimeoffset()
|
|
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Don't allocate smaller sized mappings on every iteration
sh: Try PMB mapping based on physical address, not mapping size
sh: Plug PMB alloc memory leak
sh: Sprinkle __uses_jump_to_uncached
sh: enable sleep state LEDs on Ecovec24
usb: r8a66597-udc unaligned fifo fix
sh: mach-ecovec24: Document DS2 switch settings.
sh: Build fix: export __movmem
sh: Disable unaligned kernel access printks by default.
sh: mach-ecovec24: modify 1st MTD area to read only
sh: mach-ecovec24: Add TouchScreen support
sh: magicpanelr2 and dreamcast can use the generic I/O base.
sh: Don't enable interrupts in the page fault path
sh: Set the default I/O port base to P2SEG.
sh: Handle ioport_map() cases for >= P1SEG addresses.
|
|
Currently, we've got the less than ideal situation where if we need to
allocate a 256MB mapping we'll allocate four entries like so,
entry 1: 128MB
entry 2: 64MB
entry 3: 16MB
entry 4: 16MB
This is because as we execute the loop in pmb_remap() we will
progressively try mapping the remaining address space with smaller and
smaller sizes. This isn't good because the size we use on one iteration
may be the perfect size to use on the next iteration, for instance when
the initial size is divisible by one of the PMB mapping sizes.
With this patch, we now only need two entries in the PMB to map 256MB of
address space,
entry 1: 128MB
entry 2: 128MB
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We should favour PMB mappings when the physical address cannot be
reached with 29-bits.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
If we fail to allocate a PMB entry in pmb_remap() we must remember to
clear and free any PMB entries that we may have previously allocated,
e.g. if we were allocating a multiple entry mapping.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix some callers of jump_to_uncached() and back_to_cached() that were
not annotated with __uses_jump_to_uncached.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Extend the ecovec24 board code to enable Power
Management LEDs showing the current sh7724 sleep state.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pci: Correct spelling in a comment
x86: Simplify bound checks in the MTRR code
x86: EDAC: carve out AMD MCE decoding logic
initcalls: Add early_initcall() for modules
x86: EDAC: MCE: Fix MCE decoding callback logic
|
|
* 'sparc-perf-events-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mm, perf_event: Make vmalloc_user() align base kernel virtual address to SHMLBA
perf_event: Provide vmalloc() based mmap() backing
|
|
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, timers: Check for pending timers after (device) interrupts
NOHZ: update idle state also when NOHZ is inactive
|
|
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omapfb: Blizzard: constify register address tables
omapfb: Blizzard: fix pointer to be const
omapfb: Condition mutex acquisition
omap: iovmm: Add missing mutex_unlock
omap: iovmm: Fix incorrect spelling
omap: SRAM: flush the right address after memcpy in omap_sram_push
omap: Lock DPLL5 at boot
omap: Fix incorrect 730 vs 850 detection
OMAP3: PM: introduce a new powerdomain walk helper
OMAP3: PM: Enable GPIO module-level wakeups
OMAP3: PM: USBHOST: clear wakeup events on both hosts
OMAP3: PM: PRCM interrupt: only handle selected PRCM interrupts
OMAP3: PM: PRCM interrupt: check MPUGRPSEL register
OMAP3: PM: Prevent hang in prcm_interrupt_handler
|
|
Now that range timers and deferred timers are common, I found a
problem with these using the "perf timechart" tool. Frans Pop also
reported high scheduler latencies via LatencyTop, when using
iwlagn.
It turns out that on x86, these two 'opportunistic' timers only get
checked when another "real" timer happens. These opportunistic
timers have the objective to save power by hitchhiking on other
wakeups, as to avoid CPU wakeups by themselves as much as possible.
The change in this patch runs this check not only at timer
interrupts, but at all (device) interrupts. The effect is that:
1) the deferred timers/range timers get delayed less
2) the range timers cause less wakeups by themselves because
the percentage of hitchhiking on existing wakeup events goes up.
I've verified the working of the patch using "perf timechart", the
original exposed bug is gone with this patch. Frans also reported
success - the latencies are now down in the expected ~10 msec
range.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <20091008064041.67219b13@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
agp: parisc-agp.c - use correct page_mask function
parisc: Fix linker script breakage.
parisc: convert to asm-generic/hardirq.h
parisc: Make THREAD_SIZE available to assembly files and linker scripts.
parisc: correct use of SHF_ALLOC
parisc: rename parisc's vmalloc_start to parisc_vmalloc_start
parisc: add me to Maintainers
parisc: includecheck fix: signal.c
parisc: HAVE_ARCH_TRACEHOOK
parisc: add skeleton syscall.h
parisc: stop using task->ptrace for {single,block}step flags
parisc: split syscall_trace into two halves
parisc: add missing TI_TASK macro in syscall.S
parisc: tracehook_signal_handler
parisc: tracehook_report_syscall
|
|
Blackfin already sets proper flow handlers on all IRQs, and we don't rely
on __do_IRQ, therefore we can simply select GENERIC_HARDIRQS_NO__DO_IRQ.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The patch added a special get_unmapped_area for framebuffer which
was hooked to the file ops in drivers/video/fbmem.c.
This is needed since v2.6.29-rc1 where nommu vma management was
updated, and mmap of framebuffer caused kernel BUG panic. You may turn
on "Debug the global anon/private NOMMU mapping region tree" config to
such message.
As Documentation/nommu-mmap.txt said,
"To provide shareable character device support, a driver must provide
a file->f_op->get_unmapped_area() operation. The mmap() routines will
call this to get a proposed address for the mapping."
With this change, user space should call mmap for framebuffer using
shared map. Or it can try shared map first, then private map if
failed. This shared map usage is now consistent between mmu and nommu.
The sys_ file may not be a good place for this patch. But there is a
similar one for sparc. I tested a similar patch on nios2nommu, though
I don't have a blackfin board to test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Fix the following 'make includecheck' warning:
arch/blackfin/mach-bf548/boards/ezkit.c: linux/input.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Structs get initialized to 0 already, and we want to punt this field, so
scrub it from all of our boards.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common jedec_probe supports the ST PSD4256G6V, no need to
use the custom stm_flash driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the driver has been updated, convert the board resources to the
new i2c framework for managing slaves.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The cplbinfo was using d_path() to figure out which cpu/cplb was being
parsed. As Al pointed out, this isn't exactly reliable as it assumes the
static VFS path to be unchanged, and it's just poor form. So use the
proc_create_data() to properly (and internally) pass the exact cpu/cplb
requested to the parser function.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The asm/irq.h header uses anomaly defines, but doesn't make sure to
explicitly include the anomaly header for them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Convert Blackfin to use GENERIC_TIME via the arch_getoffset()
infrastructure, reducing the amount of arch specific code we need to
maintain.
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
I was using Coccinelle with the mutex_unlock semantic patch, and it
unconvered this problem. It appears to be a valid missing unlock issue.
This change should correct it by moving the unlock below the label.
This patch is against the mainline kernel.
Cc: Julia Lawall <julia@diku.dk>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix incorrect spelling
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
the original flush operation is to flush the function address which is
copied from.
But we do not change the function code and it is not necessary to flush it.
Signed-off-by: janboe <janboe.ye@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some architectures such as Sparc, ARM and MIPS (basically
everything with flush_dcache_page()) need to deal with dcache
aliases by carefully placing pages in both kernel and user maps.
These architectures typically have to use vmalloc_user() for this.
However, on other architectures, vmalloc() is not needed and has
the downsides of being more restricted and slower than regular
allocations.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Miller <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1254830228.21044.272.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The original driver was written with the KEY() macro defined as (col,
row) instead of (row, col) as defined by the matrix keypad
infrastructure. So the keymap was defined accordingly. Since the
driver that was merged upstream uses the matrix keypad infrastructure,
modify the keymap accordingly.
While we are at it, fix the comments in twl4030.h and define
PERSISTENT_KEY as (r,c) instead of (c, r)
Tested on a RX51 (N900) device.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Lock DPLL5 at 120MHz at boot. The USBHOST 120MHz f-clock and
USBTLL f-clock are the only users of this DPLL, and 120MHz is
is the only recommended rate for these clocks.
With this patch, the 60 MHz ULPI clock is generated correctly.
Tested on an OMAP3430 SDP.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit cd92204924fafbd5c7241dfd12ca3176d542e0c5 added
support for omap850. However, the patch accidentally
removed the wrong ifdef:
# define cpu_is_omap730() 1
# endif
#endif
+#else
+# if defined(CONFIG_ARCH_OMAP850)
+# undef cpu_is_omap850
+# define cpu_is_omap850() 1
+# endif
+#endif
...
void omap2_check_revision(void);
#endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */
-
-#endif
Instead of removing removing the #endif at the end of the file,
the #endif before #else should have been removed.
But we cannot have multiple #else statements as pointed out by
Alistair Buxton <a.j.buxton@gmail.com>. So the fix is to:
- remove the non-multi-omap special handling, as we need to
detect between omap730 and omap850 anyways.
- add the missing #endif back to the end of the file
Reported-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add support for change_pte mmu notifiers
KVM: MMU: add SPTE_HOST_WRITEABLE flag to the shadow ptes
KVM: MMU: dont hold pagecount reference for mapped sptes pages
KVM: Prevent overflow in KVM_GET_SUPPORTED_CPUID
KVM: VMX: flush TLB with INVEPT on cpu migration
KVM: fix LAPIC timer period overflow
KVM: s390: fix memsize >= 4G
KVM: SVM: Handle tsc in svm_get_msr/svm_set_msr correctly
KVM: SVM: Fix tsc offset adjustment when running nested
|
|
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Clear sticky FSR register after saving it to func parametr
microblaze: UMS is used only for MMU kernel
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: using HZ needs an include of linux/param.h
sparc32: convert to asm-generic/hardirq.h
sparc64: Cache per-cpu %pcr register value in perf code.
sparc64: Fix comment typo in perf_event.c
sparc64: Minor coding style fixups in perf code.
sparc64: Add a basic conflict engine in preparation for multi-counter support.
sparc64: Increase vmalloc size to fix percpu regressions.
sparc64: Add initial perf event conflict resolution and checks.
sparc: Niagara1 perf event support.
sparc: Add Niagara2 HW cache event support.
sparc: Support all ultra3 and ultra4 derivatives.
sparc: Support HW cache events.
|
|
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't leak 64-bit kernel register values to 32-bit processes
x86, SLUB: Remove unused CONFIG FAST_CMPXCHG_LOCAL
x86: earlyprintk: Fix regression to handle serial,ttySn as 1 arg
x86: Don't generate cmpxchg8b_emu if CONFIG_X86_CMPXCHG64=y
x86: Fix csum_ipv6_magic asm memory clobber
x86: Optimize cmpxchg64() at build-time some more
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix rename of pt_regs offset defines breakage
m68knommu: remove duplicated #include
m68knommu: show KiB rather than pages in "Freeing initrd memory:" message
|
Matt Fleming
Paul Mundt
Guennadi Liakhovetski
Linus Torvalds
Magnus Damm
Arjan van de Ven
Michael Hennerich
Mike Frysinger
Thomas Chou
Jaswinder Singh Rajput
Graf Yang
Barry Song
Robin Getz
john stultz
Tony Lindgren
Daniel Walker
Hiroshi DOYU
ye janboe
Peter Zijlstra
Amit Kucheria
Rajendra Nayak