| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These are unused and should be handled by drivers/soc/ti/omap_prm.c
driver nowadays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adds a reference to the dts of the Raspberry Pi Compute Module 4
IO Board, so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-11-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
This adds the matching carrier for Raspberry Pi Compute Module 4.
Instead of xHCI USB host controller there is just a USB 2.0 interface
connected to the DWC2 controller from the BCM2711. As a result
there is a free PCIe Gen 2 socket. Also there are 2 full-size HDMI 2.0
connectors.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-10-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
The Raspberry Pi Compute Module 4 (CM4) are SoMs which contain the
following:
* BCM2711 quad core processor
* up to 8 GB RAM
* up to 32 GB eMMC
* a GPIO expander
* Gigabit PHY BCM54210PE
* Wifi/BT module with internal and external antenna
The eMMC and the Wifi/BT module are optional.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-9-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
A Wifi/BT chip is quite common for the Raspberry Pi boards. So move those
definitions into a separate dtsi in order to avoid copy & paste. This
change was inspired by a vendor tree patch from Phil Elwell.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-7-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
DT schema check complains at sd_io_1v8_reg about the following:
[1800000, 1, 3300000, 0] is too long
Additional items are not allowed (3300000, 0 were unexpected)
So fix the states definition.
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-3-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
The values of #address-cells and #size-cells are swapped. Fix this
and avoid the following DT schema warnings for mdio@e14:
#address-cells:0:0: 1 was expected
#size-cells:0:0: 0 was expected
Fixes: be8af7a9e3cc ("ARM: dts: bcm2711-rpi-4: Enable GENET support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
The VEC has a different address (0x7ec13000) on the BCM2711 (used in
e.g. Raspberry Pi 4) compared to BCM283x (e.g. Pi 3 and earlier). This
was erroneously not taken account for.
Definition of the VEC in the devicetrees had to be moved from
bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this
differentiation.
Fixes: 7894bdc6228f ("ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1626980528-3835-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
|
|
BB2D is a Vivante GC 2D Accelerator.
This adds the node to the dts file within a target module node.
Crossbar index number is used for interrupt mapping.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Change led node names to match schema.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee327111953b ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace depreciated nodenames, fix label name to match scheme.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Hyphens should be used in label names. make dtbs_check complains
about that since it does not match the corresponding pattern
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Switch the compatible for the am33xx_pinmux pin controller node from
pinctrl-single to pinconf-single. The only change between these two
compatibles is that PCS_HAS_PINCONF will be true. This then allows
pinconf properties to be utilized.
The purpose of this change is to allow the PocketBeagle to use:
pinctrl-single,bias-pullup
pinctrl-single,bias-pulldown
This dts already defines these properites for gpio pins in the default
pinctrl state but it has no effect unless PCS_HAS_PINCONF is set.
The bias properties can then be modified on the corresponding gpio lines
through the gpiod uapi. The mapping between the pins and gpio lines is
defined by gpio-ranges under the gpio controller nodes in am33xx-l4.dtsi
Signed-off-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove one of the repeated 'not' in three comments.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The double `the' in comment "get a struct clk * for the the hwmod's ..."
is repeated. Therefore, we should remove one of them from the comments.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
STM32MP151 complies with the OTG 2.0. Set it with otg-rev dt property.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1631692473-8732-4-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Nand is on CS1 so reg properties first field should be 1 not 0.
Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 94f6345712b3 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Two carveout reserved memory nodes each have been added for each of the
other remote processors devices within the MAIN domain on the TI J721E
SK boards. These nodes are assigned to the respective rproc device nodes
as well. The first region will be used as the DMA pool for the rproc
devices, and the second region will furnish the static carveout regions
for the firmware memory.
An additional reserved memory node is also added to reserve a portion of
the DDR memory to be used for performing inter-processor communication
between all the remote processors running RTOS or baremetal firmwares.
8 MB of memory is reserved for this purpose, and this accounts for all
the vrings and vring buffers between all the possible pairs of remote
processors.
The current carveout addresses and sizes are defined statically for each
rproc device. The R5F processors do not have an MMU, and as such require
the exact memory used by the firmwares to be set-aside. The C71x DSP
processor does support a MMU called CMMU, but is not currently supported
and as such requires the exact memory used by the firmware to be
set-aside. The firmware images do not require any RSC_CARVEOUT entries
in their resource tables to allocate the memory for firmware memory
segments
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-5-sinthu.raja@ti.com
|
|
Add the sub-mailbox nodes that are used to communicate between MPU and
various remote processors present in the J721E SoCs to the J721E EAIK
board. These include the R5F remote processors in the dual-R5F cluster
(MCU_R5FSS0) in the MCU domain and the two dual-R5F clusters
(MAIN_R5FSS0 & MAIN_R5FSS1) in the MAIN domain; the two C66x DSP remote
processors and the single C71x DSP remote processor in the MAIN domain.
These sub-mailbox nodes utilize the System Mailbox clusters 0 through 4.
All the remaining mailbox clusters are currently not used on A72 core,
and are hence disabled.
The sub-mailbox nodes added match the hard-coded mailbox configuration
used within the TI RTOS IPC software packages. The R5F processor
sub-systems are assumed to be running in Split mode, so a sub-mailbox
node is used by each of the R5F cores. Only the sub-mailbox node for
the first R5F core in each cluster is used in case of a Lockstep mode
for that R5F cluster.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-4-sinthu.raja@ti.com
|
|
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add basic support for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-3-sinthu.raja@ti.com
|
|
This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/cc868da8264324bde2c87d0c01d4763e3678c706.1632657917.git.jan.kiszka@web.de
|
|
The current IOT2050 devices are Product Generation 1 (PG1), using SR1.0
AM65x silicon. Upcoming PG2 devices will use SR2.x SoCs and will
therefore need separate device trees. Prepare for that by factoring out
common bits that will be shared across both generations.
At this chance, drop a link to the product homepage to in the top-level
dts files. Also fix a typo in my email address in some headers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/31fece05f9728a852c0632985c4fa537cced4ece.1632657917.git.jan.kiszka@web.de
|
|
Analogously to the am654-base-board, configure the mailboxes for the two
R5F cores, add them and the already existing memory carve-outs to the
related MCU nodes. Allows to load applications under Linux onto the
cores, e.g. the RTI watchdog firmware.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/1776f8be19b39a938d9248fcfc5332b753783c3e.1632657917.git.jan.kiszka@web.de
|
|
The IOT2050 devices described so far are using SR1.0 silicon, thus do
not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/189a91866fb1af02e4fd2345dc56774aa069d5ba.1632657917.git.jan.kiszka@web.de
|
|
This ensures that the SD card will remain mmc0 across Basic and Advanced
devices, also avoiding surprises for users coming from the downstream
kernels.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/fe20d6346f119a28e47d129b616682001299cf0e.1632657917.git.jan.kiszka@web.de
|
|
Add j7200-evm compatible to the board to allow the board to distinguish
itself from other platforms that may be added in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210925201430.11678-5-nm@ti.com
|
|
Add j721e-evm compatible to the board to allow the board to distinguish
itself from other platforms that are pending to be added.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210925201430.11678-4-nm@ti.com
|
|
Make sure that the platforms are grouped together per SoC. This helps
keep the Makefile readable as newer platforms get added to the list.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210915121442.27112-1-nm@ti.com
|
|
Add the DT nodes for the ICSSG0 and ICSSG1 processor subsystems that are
present on the K3 AM64x SoCs. The two ICSSGs are identical to each other
for the most part, with some of the peripheral pins from ICSSG1 not pinned
out. Each ICSSG instance is represented by a PRUSS subsystem node and other
child nodes.
The nodes are all added and enabled in the common k3-am64-main.dtsi
file by default. The MDIO nodes need pinctrl lines, and so should be
enabled only on boards where they are actually wired and pinned out
for ICSSG Ethernet. Any new board dts file should disable these if
they are not sure. These are disabled in the existing AM64x board dts
files to begin with.
The ICSSGs on K3 AM64x SoCs are very similar to the versions of the ICSSG
on K3 J721E and AM65x SR2.0 SoCs. The IRAM and BroadSize RAM sizes are all
identical to those on J721E SoCs. All The ICSSG host interrupts intended
towards the main Arm core are also shared with other processors on the SoC,
and can be partitioned as per system integration needs.
The ICSSG subsystem node contains the entire address space. The various
sub-modules of the ICSSG are represented as individual child nodes (so
platform devices themselves) of the PRUSS subsystem node. These include:
- two Programmable Real-Time Units (PRUs)
- two auxiliary PRU cores called RTUs
- two Transmit Programmable Real-Time Units (Tx_PRUs)
- Interrupt controller (INTC)
- a 'memories' node containing all the ICSSG level Data RAMs
- Real Time Media Independent Interface controller (MII_RT)
- Gigabit capable MII_G_RT
- ICSSG CFG sub-module providing two internal clock muxes, with the
default clock parents also assigned using the assigned-clock-parents
property.
The default names for the firmware images for each PRU, RTU and Tx_PRU
cores are defined as follows using the 'firmware-name' property (these
can be adjusted either in derivative board dts files or through sysfs at
runtime if required):
ICSSG0 PRU0 Core : am64x-pru0_0-fw ; PRU1 Core : am64x-pru0_1-fw
ICSSG0 RTU0 Core : am64x-rtu0_0-fw ; RTU1 Core : am64x-rtu0_1-fw
ICSSG0 Tx_PRU0 Core : am64x-txpru0_0-fw ; Tx_PRU1 Core : am64x-txpru0_1-fw
ICSSG1 PRU0 Core : am64x-pru1_0-fw ; PRU1 Core : am64x-pru1_1-fw
ICSSG1 RTU0 Core : am64x-rtu1_0-fw ; RTU1 Core : am64x-rtu1_1-fw
ICSSG1 Tx_PRU0 Core : am64x-txpru1_0-fw ; Tx_PRU1 Core : am64x-txpru1_1-fw
Note:
1. The ICSSG INTC on AM64x SoCs share all the host interrupts with other
processors, so use the 'ti,irqs-reserved' property in derivative board
dts files _if_ any of them should not be handled by the host OS.
2. There are few more sub-modules like the Industrial Ethernet Peripherals
(IEPs), eCAP, PWM, UART that do not have bindings and so will be added
in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210919202935.15604-1-s-anna@ti.com
|
|
Fix misspelled Kconfig symbols as detected by
scripts/checkkconfigsymbols.py.
[ bp: Combine into a single patch. ]
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210803113531.30720-7-lukas.bulwahn@gmail.com
|
|
Remove two symbols referenced in Kconfig which have been removed
previously by:
ef3c67b6454b ("mfd: intel_msic: Remove driver for deprecated platform")
1b79fc4f2bfd ("x86/apb_timer: Remove driver for deprecated platform")
Detected by scripts/checkkconfigsymbols.py.
[ bp: Merge into a single patch. ]
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210803113531.30720-5-lukas.bulwahn@gmail.com
|
|
Rebooting xtensa images loaded with the '-kernel' option in qemu does
not work. When executing a reboot command, the qemu session either hangs
or experiences an endless sequence of error messages.
Kernel panic - not syncing: Unrecoverable error in exception handler
Reset code jumps to the CPU restart address, but Linux can not recover
from there because code and data in the kernel init sections have been
discarded and overwritten at this point.
XTFPGA platforms have a means to reset the CPU by writing 0xdead into a
specific FPGA IO address. When used in QEMU the kernel image loaded with
the '-kernel' option gets restored to its original state allowing the
machine to boot successfully.
Use that mechanism to attempt a platform reset. If it does not work,
fall back to the existing mechanism.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF
is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not
selected but CONFIG_OF is.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
The simple-pm-bus driver is mandatory for CONFIG_OF based platforms to work
with fw_devlink. So, always compile it in for CONFIG_OF and delete the
config since it's no longer necessary.
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210929000735.585237-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Renesas ARM DT updates for v5.16
- I2C EEPROM support on the RZA2MEVB development board,
- DMA, USB2.0, and audio support for the RZ/G2L SoC,
- USB2.0, I2C, audio, ADC, and CANFD support for the RZ/G2L SMARC EVK
development board,
- Support for more R-Car Gen3e SoCs (H3e, M3e, M3Ne(-2G), D3e, E3e,
H3Ne),
- PWM support for the R-Car M3-W+ and V3U SoCs,
- IPMMU support for SDHI on the R-Car V3U SoC,
- Switches support for the Falcon development board,
- Improve Ethernet PHY descriptions to fix reset handling after kexec,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (45 commits)
arm64: dts: renesas: rcar-gen3: Add missing Ethernet PHY resets
ARM: dts: rzg1: Add missing Ethernet PHY resets
ARM: dts: r-mobile: Add missing Ethernet PHY resets
arm64: dts: renesas: Add compatible properties to RTL8211E Ethernet PHYs
arm64: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
arm64: dts: renesas: Add compatible properties to AR8031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to uPD6061x Ethernet PHYs
ARM: dts: renesas: Add compatible properties to RTL8201FL Ethernet PHYs
ARM: dts: renesas: Add compatible properties to LAN8710A Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8081 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8041 Ethernet PHYs
arm64: dts: renesas: beacon: Fix Ethernet PHY mode
ARM: dts: renesas: Fix SMSC Ethernet compatible values
arm64: dts: renesas: rzg2l-smarc: Enable CANFD
arm64: dts: renesas: rzg2l-smarc-som: Enable ADC on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Move extal and memory nodes to SOM DTSI
arm64: dts: renesas: r8a779a0: falcon-cpu: Add SW47-SW49 support
arm64: dts: renesas: rzg2l-smarc: Add Mic routing
arm64: dts: renesas: rzg2l-smarc: Enable audio
...
Link: https://lore.kernel.org/r/cover.1633081147.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ADC-keys for the mk808 board and a number of further cleanups
to make dt-schema happier.
* tag 'v5.16-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: swap timer clock-names
ARM: dts: rockchip: add more angle brackets to operating-points property on rk3066a
ARM: dts: rockchip: rename opp-table node names
ARM: dts: rockchip: change rv1108 gmac nodename
ARM: dts: rockchip: add adc-keys node to rk3066a-mk808
Link: https://lore.kernel.org/r/5121280.Lt9SDvczpP@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This contains the parts that were originally meant for 5.15 + some
new thing:
New boards: Firefly roc-rk3399-pc-pls and rk3328-pc; Scarlet-Dumo
tablet variant; Rock Pi 4 A+, B+; Pine64 Quartz64-A (rk3566-based)
Big additions for the rk3568: tsadc; saradc; gpio-support; gmac 1+2;
watchdog; pmu; io-domains and enabling these new things on the
rk3568-evb.
Addition of the rk3566 - a variant of the rk3568 with slightly less
peripherals.
SFC (serial flash controller) for rk3308 and px30 (including the
Odroid Go2)
Support for the rk3399's second image signal processor and its coresight
component. And camera + vpu support on px30.
A number of smaller additions to multiple boards (Rock Pi 4, Pinebook Pro
and helios64, lion-haikou, Odroid-Go2) and cleanups in some parts.
* tag 'v5.16-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (65 commits)
arm64: dts: rockchip: add phandles to muxed i2c buses on rk3368-lion
arm64: dts: rockchip: define iodomains for rk3368-lion
arm64: dts: rockchip: fix LDO_REG4 / LDO_REG7 confusion on rk3368-lion
arm64: dts: rockchip: align operating-points table name with dtschema
arm64: dts: rockchip: hook up camera on px30-evb
arm64: dts: rockchip: add isp node for px30
arm64: dts: rockchip: add Coresight debug range for RK3399
arm64: dts: rockchip: Correct regulator for USB host on Odroid-Go2
arm64: dts: rockchip: fix PCI reg address warning on rk3399-gru
arm64: dts: rockchip: add saradc to rk3568-evb1-v10
arm64: dts: rockchip: Fix GPU register width for RK3328
arm64: dts: rockchip: Re-add interrupt-names for RK3399's vpu
arm64: dts: rockchip: add missing rockchip,grf property to rk356x
arm64: dts: rockchip: add RK3399 Gru gpio-line-names
arm64: dts: rockchip: Enable SFC for Odroid Go Advance
arm64: dts: rockchip: Add SFC to RK3308
arm64: dts: rockchip: Add SFC to PX30
arm64: dts: rockchip: add thermal support to Quartz64 Model A
arm64: dts: rockchip: add rk3568 tsadc nodes
arm64: dts: rockchip: add rk356x gpio debounce clocks
...
Link: https://lore.kernel.org/r/4439872.CQOukoFCf9@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm64: dts: ZynqMP DT changes for v5.16
- Fix issues reported by dtbs_check
- Enable DMAs, DP, USB, NAND on various boards
- Add description for irps5401
- Add pinctrl description
- Add psgtr description for usb3, sata and DP
- Start to use nvmem alias for eeprom reference
- Clean up aliases list
- Wire qspi and usb3.0
- Add support for zcu102-rev1.1
- Couple of minor fixes and sync patches
* tag 'zynqmp-dt-for-v5.16' of https://github.com/Xilinx/linux-xlnx: (36 commits)
arm64: zynqmp: Wire psgtr for zc1751-xm013
arm64: zynqmp: Enable xlnx,zynqmp-dwc3 driver for xilinx boards
arm64: zynqmp: Enable gpio and qspi for zc1275-revA
arm64: zynqmp: Fix serial compatible string
arm64: zynqmp: Remove not documented is-dual property
arm64: zynqmp: Add psgtr description to zc1751 dc1 board
arm64: zynqmp: Add support for zcu102-rev1.1 board
arm64: zynqmp: Remove description for 8T49N287 and si5382 chips
arm64: zynqmp: Sync psgtr node location with zcu104-revA
arm64: zynqmp: Add reset description for sata
arm64: zynqmp: Move rtc to different location on zcu104-revA
arm64: zynqmp: Wire qspi on multiple boards
arm64: zynqmp: Remove information about dma clock on zcu106
arm64: zynqmp: Update rtc calibration value
arm64: zynqmp: Add note about UHS mode on some boards
arm64: zynqmp: Move DP nodes to the end of file on zcu106
arm64: zynqmp: Remove can aliases from zc1751
arm64: zynqmp: Add reset-on-timeout to all boards and modify default timeout value
arm64: zynqmp: List reset property for ethernet phy
arm64: zynqmp: Add nvmem alises for eeproms
...
Link: https://lore.kernel.org/r/b1cbd05d-ab40-e1fc-4001-6cf88e1e81f9@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Renesas ARM defconfig updates for v5.16
- Enable built-in (I2C, DMAC, USB PHY control) and modular (audio,
ADC) build of drivers for the RZ/G2L SoC and SMARC EVK board,
- Enable modular build of the Renesas TPU PWM driver for the R-Car
V3U SoC.
* tag 'renesas-arm-defconfig-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable RZG2L_ADC
arm64: defconfig: Enable SND_SOC_WM8978
arm64: defconfig: Enable SOUND_SOC_RZ
arm64: defconfig: Enable RZ_DMAC
arm64: defconfig: Add Renesas TPU as module
arm64: defconfig: Enable RZ/G2L USBPHY control driver
arm64: defconfig: Enable RIIC
Link: https://lore.kernel.org/r/cover.1633081145.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARMv7 multiplatform defconfig updates
A cleanup of the mutliplatform defconfig to make it easier to maintian.
* tag 'multiv7-defconfig-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: config: multi v7: Regenerate defconifg
ARM: config: multi v7: Add renamed symbols
ARM: config: multi v7: Clean up enabled by default options
ARM: config: multi v7: Drop unavailable options
Link: https://lore.kernel.org/r/CACPK8XfTHOOksA8q7MeHW=7ijP_49iOyq1pDj2SQnqSBTDUoaA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When scheduling, it is better to prefer a separate physical core rather
than the SMT sibling of a high priority core. The existing formula to
compute priorities takes such fact in consideration. There may exist,
however, combinations of priorities (i.e., maximum frequencies) in which
the priority of high-numbered SMT siblings of high-priority cores collides
with the priority of low-numbered SMT siblings of low-priority cores.
Consider for instance an SMT2 system with CPUs [0, 1] with priority 60 and
[2, 3] with priority 30(CPUs in brackets are SMT siblings. In such a case,
the resulting priorities would be [120, 60], [60, 30]. Thus, to ensure
that CPU2 has higher priority than CPU1, divide the raw priority by the
squared SMT iterator. The resulting priorities are [120, 30]. [60, 15].
Originally-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210911011819.12184-2-ricardo.neri-calderon@linux.intel.com
|
|
gcc warns that accessing a pointer based on a numeric constant may
be an offset into a NULL pointer, and would therefore has zero
accessible bytes:
arch/arm/common/sharpsl_param.c: In function ‘sharpsl_save_param’:
arch/arm/common/sharpsl_param.c:43:9: error: ‘memcpy’ reading 64 bytes from a region of size 0 [-Werror=stringop-overread]
43 | memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this particular case, the warning is bogus since this is the actual
pointer, not an offset on a NULL pointer. Add a local variable to shut
up the warning and hope it doesn't come back.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578
Link: https://lore.kernel.org/r/20210927145332.2784005-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX fixes for 5.15:
- Revert cc8870bf4c3a to fix the regression on i.MX6 that suspend
support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to
f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.
* tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable fb
ARM: dts: imx6qdl-pico: Fix Ethernet support
ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo
ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo
Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine"
ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe
Link: https://lore.kernel.org/r/20210923063356.GK13480@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The framebuffer is gone on the D-Link DIR-685, restore it.
Fixes: f611b1e7624c ("drm: Avoid circular dependencies for CONFIG_FB")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210922200933.1825752-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This can cause a randconfig warning without the 'inline' flag
that every other platform uses:
In file included from arch/arm/boot/compressed/misc.c:29:
arch/arm/mach-dove/include/mach/uncompress.h:14:13: error: 'putc' defined but not used [-Werror=unused-function]
14 | static void putc(const char c)
| ^~~~
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210927095343.1015422-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 38225f2ef2f4 ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.
This can cause a randconfig build warning that now fails the build
with -Werror:
arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
561 | static struct notifier_block omap_1510_usb_ohci_nb = {
| ^~~~~~~~~~~~~~~~~~~~~
Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
Tony Lindgren
Stefan Wahren
Mateusz Kwiatkowski
Gowtham Tammana
Andreas Kemnade
Drew Fustini
Jason Wang
Fabrice Gasnier
Roger Quadros
Sinthu Raja
Jan Kiszka
Nishanth Menon
Suman Anna
Lukas Bulwahn
Guenter Roeck
Max Filippov
Saravana Kannan
Arnd Bergmann
Ricardo Neri
Linus Walleij