| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add IPU CSI ports and capture-subsystem device so the capture subsystem
part of the IPUv3EX can be used with the staging imx-media driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables e1000 Ethernet device as it is used as a low-cost failover
Ethernet port on various QorIQ reference boards. Enabled as built-in
for booting from network without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables various PHY device drivers and PHY MUX drivers used on QorIQ
reference boards supported in mainline kernel.
Enabled as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables the RTC devices used on QorIQ reference boards supported in
mainline kernel.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the flash devices used on NXP/FSL QorIQ reference boards
supported in mainline kernel. Drivers are enabled as built-in for RFS
access without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables the Mali display driver for the display port on NXP LS1028a SoC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables generic GPIO driver for varous QorIQ SoCs. The driver can only
be built-in right now.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables NXP/FSL QorIQ IFC flash controller driver for NAND. Enabled as
built-in to load RFS from nand flash without initramfs.
Remove CONFIG_MEMORY as it is selected by CONFIG_MTD_NAND_FSL_IFC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables ARM generic SBSA compatible watchdog driver for NXP LX2160a SoC.
Enabled as built-in for it is a core feature.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables the generic QorIQ cpufreq driver to support frequency scaling
for various QorIQ SoCs. Enabled as built-in as it is a core feature.
Remove CONFIG_CLK_QORIQ as it is seleted by CONFIG_QORIQ_CPUFREQ.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables SPI controller drivers used in various NXP/FSL SoCs.
QSPI is fast enough to connect big flash for file system. It is used to
connect 512MB NAND flash and 256MB NOR flash on LS1028RDB. It is used
as bootsource for other platforms like LS2080ardb too. Enabled as
built-in to load RFS from SPI flash without requiring initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables drivers for NXP ENETC Ethernet controller and FELIX Ethernet
switch used on QorIQ LS1028a SoC.
The ENETC ethernet drivers are enabled as built-in to boot from network
without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables drivers for NXP DPAA2 framework, related Ethernet and crypto
device which can be found on QorIQ SoCs like LS1088a, LS2088a and
LX2160a.
The framework and ethernet drivers are enabled as built-in to boot
from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables drivers for NXP DPAA1 framework and related Ethernet device which
can be found on QorIQ SoCs such as LS1043a and LS1046a. They are enabled
as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables driver for FLEXCAN device which is used on a wide range of NXP
SoCs. Also enabling the related CAN framework.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Used "make defconfig savedefconfig" to regenerate defconfig files in the
right order to prepare for additional defconfig changes.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add nvmem related property for cpu0, then nvmem API could be used
to read cpu speed grading to avoid directly read OCOTP registers
mapped which could not handle defer probe.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for all the imx6qdl-pico variants.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the imx6ul pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the imx7d pico board with nymph baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the imx7d pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Olimex Olinuxino board has a user led connected to SSP1_DETECT.
But since this pin is listed in mmc0_pins_fixup, it is already claimed
by MMC driver and this results in this error during boot:
[ 1.390000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already
requested by 80010000.spi; cannot claim for leds
[ 1.400000] imx23-pinctrl 80018000.pinctrl: pin-65 (leds) status -22
[ 1.410000] imx23-pinctrl 80018000.pinctrl: could not request pin 65
(SSP1_DETECT) from group led_gpio2_1.0 on device 80018000.pinctrl
[ 1.420000] leds-gpio leds: Error applying setting, reverse things back
[ 1.430000] leds-gpio: probe of leds failed with error -22
This fix it, introduce mmc0_sck_cfg and switch the Olinuxino board to it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull x86 fixes from Thomas Gleixner:
"Two fixes for x86:
- Map EFI runtime service data as encrypted when SEV is enabled.
Otherwise e.g. SMBIOS data cannot be properly decoded by dmidecode.
- Remove the warning in the vector management code which triggered
when a managed interrupt affinity changed outside of a CPU hotplug
operation.
The warning was correct until the recent core code change that
introduced a CPU isolation feature which needs to migrate managed
interrupts away from online CPUs under certain conditions to
achieve the isolation"
* tag 'x86-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vector: Remove warning on managed interrupt migration
x86/ioremap: Map EFI runtime services data as encrypted for SEV
|
|
Pull perf fixes from Thomas Gleixner:
"A pile of perf fixes:
Kernel side:
- AMD uncore driver: Replace the open coded sanity check with the
core variant, which provides the correct error code and also leaves
a hint in dmesg
Tooling:
- Fix the stdio input handling with glibc versions >= 2.28
- Unbreak the futex-wake benchmark which was reduced to 0 test
threads due to the conversion to cpumaps
- Initialize sigaction structs before invoking sys_sigactio()
- Plug the mapfile memory leak in perf jevents
- Fix off by one relative directory includes
- Fix an undefined string comparison in perf diff"
* tag 'perf-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/amd/uncore: Replace manual sampling check with CAP_NO_INTERRUPT flag
tools: Fix off-by 1 relative directory includes
perf jevents: Fix leak of mapfile memory
perf bench: Clear struct sigaction before sigaction() syscall
perf bench futex-wake: Restore thread count default to online CPU count
perf top: Fix stdio interface input handling with glibc 2.28+
perf diff: Fix undefined string comparision spotted by clang's -Wstring-compare
perf symbols: Don't try to find a vmlinux file when looking for kernel modules
perf bench: Share some global variables to fix build with gcc 10
perf parse-events: Use asprintf() instead of strncpy() to read tracepoint files
perf env: Do not return pointers to local variables
perf tests bp_account: Make global variable static
|
|
Pull RAS fixes from Thomas Gleixner:
"Two RAS related fixes:
- Shut down the per CPU thermal throttling poll work properly when a
CPU goes offline.
The missing shutdown caused the poll work to be migrated to a
unbound worker which triggered warnings about the usage of
smp_processor_id() in preemptible context
- Fix the PPIN feature initialization which missed to enable the
functionality when PPIN_CTL was enabled but the MSR locked against
updates"
* tag 'ras-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix logic and comments around MSR_PPIN_CTL
x86/mce/therm_throt: Undo thermal polling properly on CPU offline
|
|
This patch add device node for MT2712 RTC.
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Add USB components and according pin groups in aspeed-g6 dtsi.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
make -k ARCH=arm64 dtbs_check shows the following errors. Fix them by
removing the "arm,armv8" compatible.
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long CHECK
arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex.dt.yaml
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
armada-ap806-dual.dtsi includes armada-ap806.dtsi which describes
thermal zones for 4 cpus but only cpu0 and cpu1 only exists for dual
configuration, this makes dtb compilation fail. Fix it by removing
thermal zone nodes for non-existed cpus for dual configuration.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The commit adding ESPRESSObin variants didn't include those in Makefile to
be built.
Fixes: 447b8789359f ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The commit introducing ESPRESSObin variants didn't specify dts version,
and because of that they are treated by dtc as legacy ones. Fix that by
properly specifying version in each dts.
Fixes: 447b8789359f ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This patch adds support to Analog audio via WSA881x speakers.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312143024.11059-6-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add pinctrl nodes required for QUAT I2S
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312143024.11059-5-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This patch add support to audio via WSA881x Speakers and Headset.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312143024.11059-4-srinivas.kandagatla@linaro.org
[bjorn: Sorted nodes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312143024.11059-3-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312143024.11059-2-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Pull ARC fixes from Vineet Gupta:
- Fix __ALIGN_STR and __ALIGN to not use default junk padding
- Misc Kconfig cleanups, header updates
* tag 'arc-5.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: define __ALIGN_STR and __ALIGN symbols for ARC
ARC: show_regs: reduce lines of output
ARC: Replace <linux/clk-provider.h> by <linux/of_clk.h>
ARC: fpu: fix randconfig build error reported by 0-day test service
ARC: fix some Kconfig typos
ARC: Cleanup old Kconfig IO scheduler options
|
|
Pull kvm fixes from Paolo Bonzini:
"Bugfixes for x86 and s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: avoid NULL pointer dereference with incorrect EVMCS GPAs
KVM: x86: Initializing all kvm_lapic_irq fields in ioapic_write_indirect
KVM: VMX: Condition ENCLS-exiting enabling on CPU support for SGX1
KVM: s390: Also reset registers in sync regs for initial cpu reset
KVM: fix Kconfig menu text for -Werror
KVM: x86: remove stale comment from struct x86_emulate_ctxt
KVM: x86: clear stale x86_emulate_ctxt->intercept value
KVM: SVM: Fix the svm vmexit code for WRMSR
KVM: X86: Fix dereference null cpufreq policy
|
|
|
|
When an EVMCS enabled L1 guest on KVM will tries doing enlightened VMEnter
with EVMCS GPA = 0 the host crashes because the
evmcs_gpa != vmx->nested.hv_evmcs_vmptr
condition in nested_vmx_handle_enlightened_vmptrld() will evaluate to
false (as nested.hv_evmcs_vmptr is zeroed after init). The crash will
happen on vmx->nested.hv_evmcs pointer dereference.
Another problematic EVMCS ptr value is '-1' but it only causes host crash
after nested_release_evmcs() invocation. The problem is exactly the same as
with '0', we mistakenly think that the EVMCS pointer hasn't changed and
thus nested.hv_evmcs_vmptr is valid.
Resolve the issue by adding an additional !vmx->nested.hv_evmcs
check to nested_vmx_handle_enlightened_vmptrld(), this way we will
always be trying kvm_vcpu_map() when nested.hv_evmcs is NULL
and this is supposed to catch all invalid EVMCS GPAs.
Also, initialize hv_evmcs_vmptr to '0' in nested_release_evmcs()
to be consistent with initialization where we don't currently
set hv_evmcs_vmptr to '-1'.
Cc: stable@vger.kernel.org
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM: s390: Fully do the CPU resets as intended
With 7de3f1423ff9 ("KVM: s390: Add new reset vcpu API") we clarified
the meaning of the reset ioctl to fully reset the CPU and not only the
parts that can not be handled by userspace. Turns out that we missed
some parts.
|
|
Previously all fields of structure kvm_lapic_irq were not initialized
before it was passed to kvm_bitmap_or_dest_vcpus(). Which will cause
an issue when any of those fields are used for processing a request.
For example not initializing the msi_redir_hint field before passing
to the kvm_bitmap_or_dest_vcpus(), may lead to a misbehavior of
kvm_apic_map_get_dest_lapic(). This will specifically happen when the
kvm_lowest_prio_delivery() returns TRUE due to a non-zero garbage
value of msi_redir_hint, which should not happen as the request belongs
to APIC fixed delivery mode and we do not want to deliver the
interrupt only to the lowest priority candidate.
This patch initializes all the fields of kvm_lapic_irq based on the
values of ioapic redirect_entry object before passing it on to
kvm_bitmap_or_dest_vcpus().
Fixes: 7ee30bc132c6 ("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
[Set level to false since the value doesn't really matter. Suggested
by Vitaly Kuznetsov. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The value in "new" is constructed from "old" such that all bits defined
as reserved by the ACPI spec[1] are left untouched. But if those bits
do not happen to be all zero, "new < 3" will not evaluate to true.
The firmware of the laptop(s) Medion MD63490 / Akoya P15648 comes with
garbage inside the "FACS" ACPI table. The starting value is
old=0x4944454d, therefore new=0x4944454e, which is >= 3. Mask off
the reserved bits.
[1] https://uefi.org/sites/default/files/resources/ACPI_6_2.pdf
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206553
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
BGRT is for displaying seamless OEM logo from booting to login screen;
however, this mechanism does not always work well on all configurations
and the OEM logo can be displayed multiple times. This looks worse than
without BGRT enabled.
This patch adds a kernel parameter to disable BGRT in boot time. This is
easier than re-compiling a kernel with CONFIG_ACPI_BGRT disabled.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Enable ENCLS-exiting (and thus set vmcs.ENCLS_EXITING_BITMAP) only if
the CPU supports SGX1. Per Intel's SDM, all ENCLS leafs #UD if SGX1
is not supported[*], i.e. intercepting ENCLS to inject a #UD is
unnecessary.
Avoiding ENCLS-exiting even when it is reported as supported by the CPU
works around a reported issue where SGX is "hard" disabled after an S3
suspend/resume cycle, i.e. CPUID.0x7.SGX=0 and the VMCS field/control
are enumerated as unsupported. While the root cause of the S3 issue is
unknown, it's definitely _not_ a KVM (or kernel) bug, i.e. this is a
workaround for what is most likely a hardware or firmware issue. As a
bonus side effect, KVM saves a VMWRITE when first preparing vmcs01 and
vmcs02.
Note, SGX must be disabled in BIOS to take advantage of this workaround
[*] The additional ENCLS CPUID check on SGX1 exists so that SGX can be
globally "soft" disabled post-reset, e.g. if #MC bits in MCi_CTL are
cleared. Soft disabled meaning disabling SGX without clearing the
primary CPUID bit (in leaf 0x7) and without poking into non-SGX
CPU paths, e.g. for the VMCS controls.
Fixes: 0b665d304028 ("KVM: vmx: Inject #UD for SGX ENCLS instruction in guest")
Reported-by: Toni Spets <toni.spets@iki.fi>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
g++ insists that function declaration must start with extern "C"
(which asmlinkage expands to).
gcc doesn't care.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-03-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 86 non-merge commits during the last 12 day(s) which contain
a total of 107 files changed, 5771 insertions(+), 1700 deletions(-).
The main changes are:
1) Add modify_return attach type which allows to attach to a function via
BPF trampoline and is run after the fentry and before the fexit programs
and can pass a return code to the original caller, from KP Singh.
2) Generalize BPF's kallsyms handling and add BPF trampoline and dispatcher
objects to be visible in /proc/kallsyms so they can be annotated in
stack traces, from Jiri Olsa.
3) Extend BPF sockmap to allow for UDP next to existing TCP support in order
in order to enable this for BPF based socket dispatch, from Lorenz Bauer.
4) Introduce a new bpftool 'prog profile' command which attaches to existing
BPF programs via fentry and fexit hooks and reads out hardware counters
during that period, from Song Liu. Example usage:
bpftool prog profile id 337 duration 3 cycles instructions llc_misses
4228 run_cnt
3403698 cycles (84.08%)
3525294 instructions # 1.04 insn per cycle (84.05%)
13 llc_misses # 3.69 LLC misses per million isns (83.50%)
5) Batch of improvements to libbpf, bpftool and BPF selftests. Also addition
of a new bpf_link abstraction to keep in particular BPF tracing programs
attached even when the applicaion owning them exits, from Andrii Nakryiko.
6) New bpf_get_current_pid_tgid() helper for tracing to perform PID filtering
and which returns the PID as seen by the init namespace, from Carlos Neira.
7) Refactor of RISC-V JIT code to move out common pieces and addition of a
new RV32G BPF JIT compiler, from Luke Nelson.
8) Add gso_size context member to __sk_buff in order to be able to know whether
a given skb is GSO or not, from Willem de Bruijn.
9) Add a new bpf_xdp_output() helper which reuses XDP's existing perf RB output
implementation but can be called from tracepoint programs, from Eelco Chaudron.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Philipp Zabel
Li Yang
Peng Fan
Fabio Estevam
Michael Heimpold
Anson Huang
Linus Torvalds
Ran Bi
Tao Ren
Amit Kucheria
Vadym Kochan
Tomasz Maciej Nowak
Srinivas Kandagatla
Paolo Bonzini
Vitaly Kuznetsov
Nitesh Narayan Lal
Jan Engelhardt
Alex Hung
Sean Christopherson
Alexey Dobriyan
David S. Miller