| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This operation takes a significant amount of time when hotplugging
large amounts of memory (~50 seconds with 890GB of persistent memory).
This was orignally in commit fb5924fddf9e
("powerpc/mm: Flush cache on memory hot(un)plug") to support memtrace,
but the flush on add is not needed as it is flushed on remove.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-7-alastair@au1.ibm.com
|
|
When presented with large amounts of memory being hotplugged
(in my test case, ~890GB), the call to flush_dcache_range takes
a while (~50 seconds), triggering RCU stalls.
This patch breaks up the call into 1GB chunks, calling
cond_resched() inbetween to allow the scheduler to run.
Fixes: fb5924fddf9e ("powerpc/mm: Flush cache on memory hot(un)plug")
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-6-alastair@au1.ibm.com
|
|
Similar to commit 22e9c88d486a
("powerpc/64: reuse PPC32 static inline flush_dcache_range()")
this patch converts the following ASM symbols to C:
flush_icache_range()
__flush_dcache_icache()
__flush_dcache_icache_phys()
This was done as we discovered a long-standing bug where the length of the
range was truncated due to using a 32 bit shift instead of a 64 bit one.
By converting these functions to C, it becomes easier to maintain.
flush_dcache_icache_phys() retains a critical assembler section as we must
ensure there are no memory accesses while the data MMU is disabled
(authored by Christophe Leroy). Since this has no external callers, it has
also been made static, allowing the compiler to inline it within
flush_dcache_icache_page().
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Minor fixups, don't export __flush_dcache_icache()]
Link: https://lore.kernel.org/r/20191104023305.9581-5-alastair@au1.ibm.com
|
|
This patch adds helpers to retrieve icache sizes, and renames the existing
helpers to make it clear that they are for dcache.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-4-alastair@au1.ibm.com
|
|
When calling __kernel_sync_dicache with a size >4GB, we were masking
off the upper 32 bits, so we would incorrectly flush a range smaller
than intended.
This patch replaces the 32 bit shifts with 64 bit ones, so that
the full size is accounted for.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-3-alastair@au1.ibm.com
|
|
When calling flush_icache_range with a size >4GB, we were masking
off the upper 32 bits, so we would incorrectly flush a range smaller
than intended.
This patch replaces the 32 bit shifts with 64 bit ones, so that
the full size is accounted for.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-2-alastair@au1.ibm.com
|
|
FTRACE_WITH_REGS support for arm64.
* 'arm64/ftrace-with-regs' of git://git.kernel.org/pub/scm/linux/kernel/git/mark/linux:
arm64: ftrace: minimize ifdeffery
arm64: implement ftrace with regs
arm64: asm-offsets: add S_FP
arm64: insn: add encoder for MOV (register)
arm64: module/ftrace: intialize PLT at load time
arm64: module: rework special section handling
module/ftrace: handle patchable-function-entry
ftrace: add ftrace_init_nop()
|
|
With the introduction of ZONE_DMA in arm64 we moved the default CMA and
crashkernel reservation into that area. This caused a regression on big
machines that need big CMA and crashkernel reservations. Note that
ZONE_DMA is only 1GB big.
Restore the previous behavior as the wide majority of devices are OK
with reserving these in ZONE_DMA32. The ones that need them in ZONE_DMA
will configure it explicitly.
Fixes: 1a8e1cef7603 ("arm64: use both ZONE_DMA and ZONE_DMA32")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The xen_mm_init is not exported or used outside of the file
it is declared in, so make it static. This fixes the following
sparse warning:
arch/arm/xen/mm.c:136:12: warning: symbol 'xen_mm_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Include <xen/xen-ops.h> for xen_{create,destroy}_contigous_region
call declarations. Fixes the following sparse warnings:
arch/arm/xen/mm.c:119:5: warning: symbol 'xen_create_contiguous_region' was not declared. Should it be static?
arch/arm/xen/mm.c:131:6: warning: symbol 'xen_destroy_contiguous_region' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The AST2600 has 8 32-bit timers on the APB bus.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
With the exception of i2c10 and i2c11 which conflict with the pins
for the third and forth MDIO controllers.
i2c0 has an ADT7490 fan controller/thermal monitor device connected. The
devicetree describes an adt74490 on i2c0, however bus that it appears on
depends on jumper settings, so it may not be present on all EVBs. It is
included to assist testing of I2C.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
AMD 2nd generation EPYC processors also support the UMIP feature. Make
the comments vendor-agnostic.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "x86@kernel.org" <x86@kernel.org>
Link: https://lkml.kernel.org/r/157298913784.17462.12654728938970637305.stgit@naples-babu.amd.com
|
|
Bring powerpc in line with other architectures that support extending or
overriding the bootloader provided command line.
The current behaviour is most like CMDLINE_FROM_BOOTLOADER where the
bootloader command line is preferred but the kernel config can provide a
fallback so CMDLINE_FROM_BOOTLOADER is the default. CMDLINE_EXTEND can
be used to append the CMDLINE from the kernel config to the one provided
by the bootloader.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190801225006.21952-1-chris.packham@alliedtelesis.co.nz
|
|
AMD 2nd generation EPYC processors support the UMIP (User-Mode
Instruction Prevention) feature. So, rename X86_INTEL_UMIP to
generic X86_UMIP and modify the text to cover both Intel and AMD.
[ bp: take of the disabled-features.h copy in tools/ too. ]
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "x86@kernel.org" <x86@kernel.org>
Link: https://lkml.kernel.org/r/157298912544.17462.2018334793891409521.stgit@naples-babu.amd.com
|
|
Invoke the EFI_RNG_PROTOCOL protocol in the context of the x86 EFI stub,
same as is done on arm/arm64 since commit 568bc4e87033 ("efi/arm*/libstub:
Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table"). Within the stub,
a Linux-specific RNG seed UEFI config table will be seeded. The EFI routines
in the core kernel will pick that up later, yet still early during boot,
to seed the kernel entropy pool. If CONFIG_RANDOM_TRUST_BOOTLOADER, entropy
is credited for this seed.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The recently introduced Energy Model (EM) framework manages power cost
tables for the CPUs of the system. Its only user right now is the
scheduler, in the context of Energy Aware Scheduling (EAS).
However, the EM framework also offers a generic infrastructure that
could replace subsystem-specific implementations of the same concepts,
as this is the case in the thermal framework.
So, in order to prepare the migration of the thermal subsystem to use
the EM framework, enable it in the default arm64 defconfig, which is the
most commonly used architecture for IPA. This will also compile-in all
of the EAS code, although it won't be enabled by default -- EAS requires
to use the 'schedutil' CPUFreq governor while arm64 defaults to
'performance'.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191030151451.7961-2-qperret@google.com
|
|
The powerpc-specific bitops are not being picked up by the KASAN
test suite.
Instrumentation is done via the bitops/instrumented-{atomic,lock}.h
headers. They require that arch-specific versions of bitop functions
are renamed to arch_*. Do this renaming.
For clear_bit_unlock_is_negative_byte, the current implementation
uses the PG_waiters constant. This works because it's a preprocessor
macro - so it's only actually evaluated in contexts where PG_waiters
is defined. With instrumentation however, it becomes a static inline
function, and all of a sudden we need the actual value of PG_waiters.
Because of the order of header includes, it's not available and we
fail to compile. Instead, manually specify that we care about bit 7.
This is still correct: bit 7 is the bit that would mark a negative
byte.
While we're at it, replace __inline__ with inline across the file.
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820024941.12640-2-dja@axtens.net
|
|
Currently bitops-instrumented.h assumes that the architecture provides
atomic, non-atomic and locking bitops (e.g. both set_bit and __set_bit).
This is true on x86 and s390, but is not always true: there is a
generic bitops/non-atomic.h header that provides generic non-atomic
operations, and also a generic bitops/lock.h for locking operations.
powerpc uses the generic non-atomic version, so it does not have it's
own e.g. __set_bit that could be renamed arch___set_bit.
Split up bitops-instrumented.h to mirror the atomic/non-atomic/lock
split. This allows arches to only include the headers where they
have arch-specific versions to rename. Update x86 and s390.
(The generic operations are automatically instrumented because they're
written in C, not asm.)
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Marco Elver <elver@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190820024941.12640-1-dja@axtens.net
|
|
There are several boards available depending on the PCB
(3 antennas support and several revison). Add a dtsi file to share
common binding between all kizbox2 boards. This patch also add support
for the kizbox2-2 variant.
Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com>
Signed-off-by: Mickael GARDET <m.gardet@overkiz.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20191105212234.22999-2-kamel.bouhara@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Qualcomm Device Tree Changes for v5.5
* Add thermal zones and IRQ support for MSM8974
* Add 5vs2 regulator node for PM8941
* Add reboot-mode node, fix sdhci and card detect on MSM8974-FP2
* Add IPQ4019 SDHCI node
* tag 'qcom-dts-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: msm8974: thermal: Add thermal zones for each sensor
ARM: dts: msm8974: thermal: Add interrupt support
ARM: dts: qcom: pm8941: add 5vs2 regulator node
ARM: dts: msm8974-FP2: add reboot-mode node
ARM: dts: msm8974-FP2: Increase load on l20 for sdhci
ARM: dts: msm8974-FP2: Drop unused card-detect pin
ARM: dts: qcom: ipq4019: Add SDHCI controller node
Link: https://lore.kernel.org/r/1573068840-13098-5-git-send-email-agross@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Qualcomm ARM Based defconfig Updates for v5.5
* Enable OCMEM support
* tag 'qcom-defconfig-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: qcom_defconfig: add ocmem support
Link: https://lore.kernel.org/r/1573068840-13098-3-git-send-email-agross@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Qualcomm ARM64 Updates for v5.5
* Add thermal IRQ support on MSM8916, SDM845, MSM8996, and QCS404
* Fix thermal HW ids for cpus on MSM8916
* Add blsp1 UART3 and blsp1 BAM on MSM8998
* Add volume buttons and WCNSS for Wifi and BT on MSM8916 LongCheer-l8150
* Fixup load on l21 for SD on apq8096-db820c
* Enable LVS1/2, APSS watchdog, and select UFS reset gpio for SDM845
* Disable coresight by default on MSM8998
* Enable bluetooth and remove retention idle state on MSM8998-clamshell
* Enable adsp, cdsp, and mpss on C630
* Enable bluetooth on MSM8998-mtp
* Delete zap shader on SDM845-cheza
* Add tactile buttons and hall sensor on MSM8916-Samsung-A2015
* Add Interconnect nodes, watchdog, and sleep clk on QCS404
* Override Iris compatible on MSM8916-Samsung-A5U
* Enable WCNSS Wifi and bluetooth on MSM8916-Samsung-A2015
* Fixup cooling states for the aoss warming devices
* tag 'qcom-arm64-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (26 commits)
arm64: dts: qcom: db845c: Enable LVS 1 and 2
arm64: dts: qcom: msm8998: Disable coresight by default
arm64: dts: qcom: msm8998-clamshell: Remove retention idle state
arm64: dts: qcom: sdm845-cheza: delete zap-shader
arm64: dts: msm8916: thermal: Fixup HW ids for cpu sensors
arm64: dts: sdm845: thermal: Add interrupt support
arm64: dts: msm8996: thermal: Add interrupt support
arm64: dts: msm8998: thermal: Add interrupt support
arm64: dts: qcs404: thermal: Add interrupt support
arm64: dts: qcom: sdm845: Add APSS watchdog node
arm64: dts: qcom: c630: Enable adsp, cdsp and mpss
arm64: dts: qcom: msm8998-clamshell: Enable bluetooth
arm64: dts: qcom: msm8998-mtp: Enable bluetooth
arm64: dts: qcom: msm8998: Add blsp1_uart3
arm64: dts: qcom: msm8998: Add blsp1 BAM
arm64: dts: msm8916-longcheer-l8150: Add Volume buttons
arm64: dts: msm8916-longcheer-l8150: Enable WCNSS for WiFi and BT
soc: qcom: Invert the cooling states for the aoss warming devices
arm64: dts: apq8096-db820c: Increase load on l21 for SDCARD
arm64: dts: msm8916-samsung-a2015: add tactile buttons and hall sensor
...
Link: https://lore.kernel.org/r/1573068840-13098-2-git-send-email-agross@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible: Additional items are not allowed ('amlogic,meson-gxbb-i2c' was unexpected)
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible:0: 'amlogic,meson-gx-i2c' is not one of ['amlogic,meson6-i2c', 'amlogic,meson-gxbb-i2c', 'amlogic,meson-axg-i2c']
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible: ['amlogic,meson-gx-i2c', 'amlogic,meson-gxbb-i2c'] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxl-s905x-hwacom-amazetv.dt.yaml: cec@100: 'hdmi-phandle' is a required property
meson-gxm-rbox-pro.dt.yaml: cec@100: 'hdmi-phandle' is a required property
because CEC is not enabled on these boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12b-odroid-n2.dt.yaml: /: compatible: ['hardkernel,odroid-n2', 'amlogic,g12b'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxm-khadas-vim2.dt.yaml: gpu@c0000: interrupt-names:0: 'job' was expected
meson-gxm-khadas-vim2.dt.yaml: gpu@c0000: interrupt-names:2: 'gpu' was expected
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:0: 'job' was expected
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:2: 'gpu' was expected
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Following commit 73e86cb03cf2 ("arm64: Move PTE_RDONLY bit handling out
of set_pte_at()"), the PTE_RDONLY bit is no longer managed by
set_pte_at() but built into the PAGE_* attribute definitions.
Consequently, pte_same() must include this bit when checking two PTEs
for equality.
Remove the arm64-specific pte_same() function, practically reverting
commit 747a70e60b72 ("arm64: Fix copy-on-write referencing in HugeTLB")
Fixes: 73e86cb03cf2 ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
i.MX defconfig update for 5.5:
- Enable i.MX7ULP watchdog, DA9052 touch and USB configfs support
in imx_v6_v7_defconfig.
- Enable newly added S32V234 SoC and its UART driver support in arm64
defconfig.
- Built i.MX8QXP SCU key driver as module in arm64 defconfig.
- Change AT803X Ethernet PHY driver from module to built-in, so that
we can boot i.MX8MM EVK board with rootfs on NFS.
* tag 'imx-defconfig-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: Change CONFIG_AT803X_PHY from m to y
ARM: imx_v6_v7_defconfig: Enable CONFIG_TOUCHSCREEN_DA9052
arm64: defconfig: Enable configs for S32V234
arm64: defconfig: Enable CONFIG_KEYBOARD_IMX_SC_KEY as module
ARM: imx_v6_v7_defconfig: Build USB_CONFIGFS into kernel
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX7ULP_WDT by default
Link: https://lore.kernel.org/r/20191105150315.15477-7-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
LX2160A TMU support for 5.5:
- Add TMU (Thermal Monitoring Unit) device node to enable thermal
support on LX2160A SoC.
* tag 'imx-dt64-tmu-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: lx2160a: add tmu device node
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191105150315.15477-6-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX arm64 device tree changes for 5.5:
- Add the initial support for a new arm64 family SoC from NXP:
S32V234 ("Treerunner") vision microprocessors which are targeted for
high-performance, computationally intensive vision and sensor fusion
applications that require automotive safety levels.
- New board support: i.MX8MN LPDDR4 EVK, i.MX8QXP Colibri and
S32V234 EVB.
- A series of patch from Andrey Smirnov to improve zii-ultra support by
fixing regulator and adding accelerometer, switch watchdog.
- Add system counter device and enable cpuidle support for i.MX8MN.
- Move usdhc clocks assignment from SoC to board level DTS for
i.MX8 based boards.
- Add PCA6416 on I2C3 bus for imx8mm-evk, and enable SCU key for
imx8qxp-mek board.
- Enable GPU passive throttling on i.MX8MQ SoC, and add DDR PMU device
for i.MX8MN.
- A series from Fabio Estevam to fix DTC W=1 warnings for LS1028A device.
- Update the clock providers for the Mali DP500 and '#clock-cells' of
DPCLK node for LS1028A SoC.
- Misc small updates on various boards.
* tag 'imx-dt64-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
arm64: dts: imx8mn-evk: Remove invalid Atheros properties
arm64: dts: freescale: add initial support for colibri imx8x
arm64: dts: ls1028a: Fix tmu unit address
arm64: dts: ls1028a: Move thermal-zone out of SoC
arm64: dts: ls1028a-qds: Remove unnecessary #address-cells/#size-cells
arm64: dts: imx8mn: Remove duplicated machine compatible
arm64: dts: imx8mm: Remove duplicated machine compatible
arm64: dts: imx8mq-evk: Add remote control
arm64: dts: imx8mn: Add LPDDR4 EVK board support
arm64: dts: imx8mn: Create EVK dtsi file for common use
arm64: dts: imx8mn: Move usdhc clocks assignment to board DT
arm64: dts: imx8mm: Move usdhc clocks assignment to board DT
arm64: dts: imx8mq: Move usdhc clocks assignment to board DT
arm64: dts: imx8qxp: Move usdhc clocks assignment to board DT
arm64: dts: fsl: Add device tree for S32V234-EVB
arm64: dts: imx8mm-evk: Assigned clocks for audio plls
arm64: dts: zii-ultra: Add node for switch watchdog
arm64: dts: zii-ultra: Add node for accelerometer
arm64: dts: zii-ultra: Fix regulator-3p3-main's name
arm64: dts: zii-ultra: Fix regulator-vsd-3v3's vin-supply
...
Link: https://lore.kernel.org/r/20191105150315.15477-5-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX device tree changes for 5.5:
- New board support: Netronix E60K02 and Kobo Clara HD, Kontron N6311
and N6411, OPOS6UL and OPOS6ULDev.
- Correct speed grading fuse settings and add opp-suspend property for
i.MX7D device tree.
- Move usdhc clocks assignment from SoC to board level DTS for imx7ulp,
and use APLL_PFD1 as usdhc's clock source on imx7ulp-evk board.
- Add missing cooling device properties for CPUs for i.MX6/7 SoCs.
- Add sensor GPIO regulator and assign power supplies for magnetometer
for imx6ul-14x14-evk board.
- Replace "simple-bus" with "simple-mfd" for ANATOP device for i.MX6/7
SoCs.
- Fix DTC W=1 warnings by not using simple-audio-card,dai-link on
imx6qdl-gw551x and imx6q-gw54xx board.
- Move to use DRM bindings for the Seiko 43WVF1G panel on imx53-qsb.
- A series from Frieder Schrempf to support more i.MX6UL/ULL-based SoMs
and boards from Kontron Electronics GmbH.
- A few patches from Michal Vokáč to enable more devices support on
imx6dl-yapp4 board.
- A patch series from Philippe Schenker to improve i.MX6/7 Apalis and
Colibri board support.
- A patch series from Sébastien Szymanski to update i.MX6 APF6/APF6Dev
device tree with more devices added and adopting DRM bindings for
display.
- Random improvements, clean-up and device additions on various boards.
* tag 'imx-dt-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (68 commits)
ARM: dts: imx6ul-kontron-n6x1x-s: Remove an obsolete comment and fix indentation
ARM: dts: imx6ul-kontron-n6x1x-s: Add vbus-supply and overcurrent polarity to usb nodes
ARM: dts: imx6ul-kontron-n6x1x: Add 'chosen' node with 'stdout-path'
ARM: dts: Add support for two more Kontron evalkit boards 'N6311 S' and 'N6411 S'
ARM: dts: imx6ul-kontron-n6310-s: Move common nodes to a separate file
ARM: dts: imx6ul-kontron-n6310-s: Disable the snvs-poweroff driver
ARM: dts: Add support for two more Kontron SoMs N6311 and N6411
ARM: dts: imx6ul-kontron-n6310: Move common SoM nodes to a separate file
ARM: dts: imx7ulp-evk: Use APLL_PFD1 as usdhc's clock source
ARM: dts: imx: add devicetree for Kobo Clara HD
ARM: dts: add Netronix E60K02 board common file
ARM: dts: vf-colibri: fix typo in top-level module compatible
ARM: dts: imx53-qsb: Use DRM bindings for the Seiko 43WVF1G panel
ARM: dts: imx53: Spelling s/configration/configuration/
ARM: dts: imx6ul-14x14-evk: Assign power supplies for magnetometer
ARM: dts: imx6ul-14x14-evk: Fix the magnetometer node name
ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator
ARM: dts: imx6ul: Disable gpt2 by default
ARM: dts: imx7d: Add missing cooling device properties for CPUs
ARM: dts: imx6dl: Add missing cooling device properties for CPUs
...
Link: https://lore.kernel.org/r/20191105150315.15477-4-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX SoC update for 5.5:
- Add arm64 Kconfig option for the NXP S32 platform.
- Drop imx_anatop_usb_chrg_detect_disable() function which becomes
unneeded, since all the necessary charger setup is done by the USB
PHY driver now.
- Add serial number support for i.MX6/7 SoCs by reading 64-bit SoC
unique ID from OCOTP block.
- Replace i.MX machine specific coherency exit implementation using
the generic v7_exit_coherency_flush() function.
* tag 'imx-soc-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: use generic function to exit coherency
ARM: imx: Add serial number support for i.MX6/7 SoCs
ARM: imx: Drop imx_anatop_usb_chrg_detect_disable()
arm64: Introduce config for S32
Link: https://lore.kernel.org/r/20191105150315.15477-2-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Samsung mach/soc changes for v5.5
1. Minor cleanups in S3C platforms,
2. Enable newly added EXYNOS_ASV (Adaptive Supply Voltage) driver.
* tag 'samsung-soc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos: Enable exynos-asv driver for ARCH_EXYNOS
ARM: s3c: Rename s5p_usb_phy functions
ARM: s3c: Rename s3c64xx_spi_setname() function
Link: https://lore.kernel.org/r/20191104175902.12224-2-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A few more DT patches for 5.5, mostly:
- USB3 support for the H6
- Deinterlacer support for the H3
- eDP Bridge support on the Teres-I
- More DT cleanups thanks to the validation
* tag 'sunxi-dt-for-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Remove useless reset name
ARM: dts: sun6i: Remove useless reset-names
arm64: dts: allwinner: orange-pi-3: Enable USB 3.0 host support
arm64: dts: allwinner: h6: add USB3 device nodes
dt-bindings: Add ANX6345 DP/eDP transmitter binding
arm64: dts: allwinner: a64: enable ANX6345 bridge on Teres-I
dts: arm: sun8i: h3: Enable deinterlace unit
ARM: dts: sunxi: h3/h5: Add MBUS controller node
dt-bindings: bus: sunxi: Add H3 MBUS compatible
Link: https://lore.kernel.org/r/58ad00a8-9579-4811-969a-a74e331ee9a2.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
One patch to add back the PMU node that was removed because the
interrupts were improper in a previous fixes PR.
* tag 'sunxi-fixes-for-5.4-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Re-add PMU node
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/45023fa6-b2bc-4934-b85c-3e7841dde0b1.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
STM32 DT fixes for v5.4, round 2
Highlights:
-----------
Fixes for STM32MP157:
-Fix CAN RAM mapping
-Change stmfx pinctrl definition for joystick and camera. Due to
stmfx pinctrl fix done in v5.4-rc cycle, camera and joystick were no
longer functional.
* tag 'stm32-dt-for-v5.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
Link: https://lore.kernel.org/r/d316b81f-a8d7-e9be-fe3c-73a242e7d941@st.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we no longer refer to mod->arch.ftrace_trampolines in the body
of ftrace_make_call(), we can use IS_ENABLED() rather than ifdeffery,
and make the code easier to follow. Likewise in ftrace_make_nop().
Let's do so.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
|
|
This patch implements FTRACE_WITH_REGS for arm64, which allows a traced
function's arguments (and some other registers) to be captured into a
struct pt_regs, allowing these to be inspected and/or modified. This is
a building block for live-patching, where a function's arguments may be
forwarded to another function. This is also necessary to enable ftrace
and in-kernel pointer authentication at the same time, as it allows the
LR value to be captured and adjusted prior to signing.
Using GCC's -fpatchable-function-entry=N option, we can have the
compiler insert a configurable number of NOPs between the function entry
point and the usual prologue. This also ensures functions are AAPCS
compliant (e.g. disabling inter-procedural register allocation).
For example, with -fpatchable-function-entry=2, GCC 8.1.0 compiles the
following:
| unsigned long bar(void);
|
| unsigned long foo(void)
| {
| return bar() + 1;
| }
... to:
| <foo>:
| nop
| nop
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl 0 <bar>
| add x0, x0, #0x1
| ldp x29, x30, [sp], #16
| ret
This patch builds the kernel with -fpatchable-function-entry=2,
prefixing each function with two NOPs. To trace a function, we replace
these NOPs with a sequence that saves the LR into a GPR, then calls an
ftrace entry assembly function which saves this and other relevant
registers:
| mov x9, x30
| bl <ftrace-entry>
Since patchable functions are AAPCS compliant (and the kernel does not
use x18 as a platform register), x9-x18 can be safely clobbered in the
patched sequence and the ftrace entry code.
There are now two ftrace entry functions, ftrace_regs_entry (which saves
all GPRs), and ftrace_entry (which saves the bare minimum). A PLT is
allocated for each within modules.
Signed-off-by: Torsten Duwe <duwe@suse.de>
[Mark: rework asm, comments, PLTs, initialization, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Julien Thierry <jthierry@redhat.com>
Cc: Will Deacon <will@kernel.org>
|
|
So that assembly code can more easily manipulate the FP (x29) within a
pt_regs, add an S_FP asm-offsets definition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
|
|
For FTRACE_WITH_REGS, we're going to want to generate a MOV (register)
instruction as part of the callsite intialization. As MOV (register) is
an alias for ORR (shifted register), we can generate this with
aarch64_insn_gen_logical_shifted_reg(), but it's somewhat verbose and
difficult to read in-context.
Add a aarch64_insn_gen_move_reg() wrapper for this case so that we can
write callers in a more straightforward way.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
|
|
Currently we lazily-initialize a module's ftrace PLT at runtime when we
install the first ftrace call. To do so we have to apply a number of
sanity checks, transiently mark the module text as RW, and perform an
IPI as part of handling Neoverse-N1 erratum #1542419.
We only expect the ftrace trampoline to point at ftrace_caller() (AKA
FTRACE_ADDR), so let's simplify all of this by intializing the PLT at
module load time, before the module loader marks the module RO and
performs the intial I-cache maintenance for the module.
Thus we can rely on the module having been correctly intialized, and can
simplify the runtime work necessary to install an ftrace call in a
module. This will also allow for the removal of module_disable_ro().
Tested by forcing ftrace_make_call() to use the module PLT, and then
loading up a module after setting up ftrace with:
| echo ":mod:<module-name>" > set_ftrace_filter;
| echo function > current_tracer;
| modprobe <module-name>
Since FTRACE_ADDR is only defined when CONFIG_DYNAMIC_FTRACE is
selected, we wrap its use along with most of module_init_ftrace_plt()
with ifdeffery rather than using IS_ENABLED().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
|
|
When we load a module, we have to perform some special work for a couple
of named sections. To do this, we iterate over all of the module's
sections, and perform work for each section we recognize.
To make it easier to handle the unexpected absence of a section, and to
make the section-specific logic easer to read, let's factor the section
search into a helper. Similar is already done in the core module loader,
and other architectures (and ideally we'd unify these in future).
If we expect a module to have an ftrace trampoline section, but it
doesn't have one, we'll now reject loading the module. When
ARM64_MODULE_PLTS is selected, any correctly built module should have
one (and this is assumed by arm64's ftrace PLT code) and the absence of
such a section implies something has gone wrong at build time.
Subsequent patches will make use of the new helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
|
|
When using patchable-function-entry, the compiler will record the
callsites into a section named "__patchable_function_entries" rather
than "__mcount_loc". Let's abstract this difference behind a new
FTRACE_CALLSITE_SECTION, so that architectures don't have to handle this
explicitly (e.g. with custom module linker scripts).
As parisc currently handles this explicitly, it is fixed up accordingly,
with its custom linker script removed. Since FTRACE_CALLSITE_SECTION is
only defined when DYNAMIC_FTRACE is selected, the parisc module loading
code is updated to only use the definition in that case. When
DYNAMIC_FTRACE is not selected, modules shouldn't have this section, so
this removes some redundant work in that case.
To make sure that this is keep up-to-date for modules and the main
kernel, a comment is added to vmlinux.lds.h, with the existing ifdeffery
simplified for legibility.
I built parisc generic-{32,64}bit_defconfig with DYNAMIC_FTRACE enabled,
and verified that the section made it into the .ko files for modules.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Helge Deller <deller@gmx.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Tested-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Torsten Duwe <duwe@suse.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: linux-parisc@vger.kernel.org
|
|
As it was found recently, the Performance Monitoring Unit (PMU) on the
Allwinner A64 SoC was not generating (the right) interrupts. With the
SPI numbers from the manual the kernel did not receive any overflow
interrupts, so perf was not happy at all.
It turns out that the numbers were just off by 4, so the PMU interrupts
are from 148 to 151, not from 152 to 155 as the manual describes.
This was found by playing around with U-Boot, which typically does not
use interrupts, so the GIC is fully available for experimentation:
With *every* PPI and SPI enabled, an overflowing PMU cycle counter was
found to set a bit in one of the GICD_ISPENDR registers, with careful
counting this was determined to be number 148.
Tested with perf record and perf top on a Pine64-LTS. Also tested with
tasksetting to every core to confirm the assignment between IRQs and
cores.
This somewhat "revert-fixes" commit ed3e9406bcbc ("arm64: dts: allwinner:
a64: Drop PMU node").
Fixes: 34a97fcc71c2 ("arm64: dts: allwinner: a64: Add PMU node")
Fixes: ed3e9406bcbc ("arm64: dts: allwinner: a64: Drop PMU node")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
NVIDIA Carmel CPUs don't implement ID_AA64PFR0_EL1.CSV3 but
aren't susceptible to Meltdown, so add Carmel to kpti_safe_list[].
Signed-off-by: Rich Wiley <rwiley@nvidia.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
commit 9b31cf493ffa ("arm64: mm: Introduce MAX_USER_VA_BITS definition")
introduced the MAX_USER_VA_BITS definition, which was used to support
the arm64 mm use-cases where the user-space could use 52-bit virtual
addresses whereas the kernel-space would still could a maximum of 48-bit
virtual addressing.
But, now with commit b6d00d47e81a ("arm64: mm: Introduce 52-bit Kernel
VAs"), we removed the 52-bit user/48-bit kernel kconfig option and hence
there is no longer any scenario where user VA != kernel VA size
(even with CONFIG_ARM64_FORCE_52BIT enabled, the same is true).
Hence we can do away with the MAX_USER_VA_BITS macro as it is equal to
VA_BITS (maximum VA space size) in all possible use-cases. Note that
even though the 'vabits_actual' value would be 48 for arm64 hardware
which don't support LVA-8.2 extension (even when CONFIG_ARM64_VA_BITS_52
is enabled), VA_BITS would still be set to a value 52. Hence this change
would be safe in all possible VA address space combinations.
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: linux-kernel@vger.kernel.org
Cc: kexec@lists.infradead.org
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Calculate the page-aligned end address more simply.
The local variable, "length" is unneeded.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Fixes: a502b343ebd0 ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
Alastair D'Silva
Catalin Marinas
Nicolas Saenz Julienne
Ben Dooks (Codethink)
Joel Stanley
Babu Moger
Chris Packham
Dominik Brodowski
Quentin Perret
Daniel Axtens
Kamel Bouhara
Olof Johansson
Neil Armstrong
Mark Rutland
Torsten Duwe
Andre Przywara
Rich Wiley
Bhupesh Sharma
Masahiro Yamada
Amelie Delaunay