| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Enable blsp1_uart3, define its pinconf and add the bluetooth node.
It seems provisioning is lacking a valid BD address, preventing the
interface from initializing, so provide a dummy for now.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Define the EVB pms405_s3 supplies.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The PMS405 sports 5 SMPS and 13 LDO regulators, add the regulators to
pms405 DTS.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bjorn: updated label]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add host controller and PHY DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The UFS host controller driver needs to set the load on 3 power rails
(l20, l26, s4) but the operation fails silently unless we specify the
regulator-allow-set-load property in the corresponding DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The property controlled-remotely should not be set by default
for qcs-404 device, it should be set based on the secure boot
options (TZ or ATF) preferred by the platform. Hence, the
controlled-remotely property is moved to platform specific
dts files.
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
PMS405 L3 is outside the acceptable range, causing PCIe to fail. Fix
these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bjorn: Hunk fixing up S5 already applied, updated commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
EVB-4000 comes with ethernet so enable it and add pinctrl bindings.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the ethernet node found in QCS404 platform.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Include the device tree header for the on-chip interconnect endpoint
resources on sdm845 devices. This will allow using the "interconnects"
property in DT nodes to describe the interconnect path resources they use.
The sdm845 interconnect provider DT node is already present, but the
header file with the resources is not included, so let's fix this.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The regulator definition got their supply names cleaned up during
upstreaming, so they no longer match the driver defined names. Update
the supply names.
Also fill out the missing voltage of SMPS 5.
Fixes: 0b363f5b871c ("arm64: dts: qcom: qcs404: Add PMS405 RPM regulators")
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
If we use "crashkernel=Y[@X]" and the start address is above 4G,
the arm64 kdump capture kernel may call memblock_alloc_low() failure
in request_standard_resources(). Replacing memblock_alloc_low() with
memblock_alloc().
[ 0.000000] MEMBLOCK configuration:
[ 0.000000] memory size = 0x0000000040650000 reserved size = 0x0000000004db7f39
[ 0.000000] memory.cnt = 0x6
[ 0.000000] memory[0x0] [0x00000000395f0000-0x000000003968ffff], 0x00000000000a0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x1] [0x0000000039730000-0x000000003973ffff], 0x0000000000010000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x2] [0x0000000039780000-0x000000003986ffff], 0x00000000000f0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x3] [0x0000000039890000-0x0000000039d0ffff], 0x0000000000480000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x4] [0x000000003ed00000-0x000000003ed2ffff], 0x0000000000030000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x5] [0x0000002040000000-0x000000207fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
[ 0.000000] reserved.cnt = 0x7
[ 0.000000] reserved[0x0] [0x0000002040080000-0x0000002041c4dfff], 0x0000000001bce000 bytes flags: 0x0
[ 0.000000] reserved[0x1] [0x0000002041c53000-0x0000002042c203f8], 0x0000000000fcd3f9 bytes flags: 0x0
[ 0.000000] reserved[0x2] [0x000000207da00000-0x000000207dbfffff], 0x0000000000200000 bytes flags: 0x0
[ 0.000000] reserved[0x3] [0x000000207ddef000-0x000000207fbfffff], 0x0000000001e11000 bytes flags: 0x0
[ 0.000000] reserved[0x4] [0x000000207fdf2b00-0x000000207fdfc03f], 0x0000000000009540 bytes flags: 0x0
[ 0.000000] reserved[0x5] [0x000000207fdfd000-0x000000207ffff3ff], 0x0000000000202400 bytes flags: 0x0
[ 0.000000] reserved[0x6] [0x000000207ffffe00-0x000000207fffffff], 0x0000000000000200 bytes flags: 0x0
[ 0.000000] Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-next-20190321+ #4
[ 0.000000] Call trace:
[ 0.000000] dump_backtrace+0x0/0x188
[ 0.000000] show_stack+0x24/0x30
[ 0.000000] dump_stack+0xa8/0xcc
[ 0.000000] panic+0x14c/0x31c
[ 0.000000] setup_arch+0x2b0/0x5e0
[ 0.000000] start_kernel+0x90/0x52c
[ 0.000000] ---[ end Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes ]---
Link: https://www.spinics.net/lists/arm-kernel/msg715293.html
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Have the IMA architecture specific policy require signed kernel modules
on systems with secure boot mode enabled; and coordinate the different
signature verification methods, so only one signature is required.
Requiring appended kernel module signatures may be configured, enabled
on the boot command line, or with this patch enabled in secure boot
mode. This patch defines set_module_sig_enforced().
To coordinate between appended kernel module signatures and IMA
signatures, only define an IMA MODULE_CHECK policy rule if
CONFIG_MODULE_SIG is not enabled. A custom IMA policy may still define
and require an IMA signature.
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
|
|
Since commit
ad67b74d2469 ("printk: hash addresses printed with %p")
at boot "____ptrval____" is printed instead of the trampoline addresses:
Base memory trampoline at [(____ptrval____)] 99000 size 24576
Remove the print as we don't want to leak kernel addresses and this
statement is not needed anymore.
Fixes: ad67b74d2469d9b8 ("printk: hash addresses printed with %p")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190326203046.20787-1-mcroce@redhat.com
|
|
The declarations related to immovable memory handling are out of the
BOOT_COMPRESSED_MISC_H #ifdef scope, wrap them inside.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190304055546.18566-1-bhe@redhat.com
|
|
The RK3399-Q7 (Puma) requires 33 Ohm drive strength to ensure signal
integrity at HS-400 (200MHz clock, DDR signalling).
A repeated EMC testing run validates that this increase does not
negatively impact EMC compliance (emissions have ample distance to
the regulatory limits).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A previous patch introduced the property 'drive-impedance-ohm'
for the RK3399's emmc phy node. This patch sets this value
explicitly to the default value of 50 Ohm.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When using direct commands (DCMDs) on an RK3399, we get spurious
CQE completion interrupts for the DCMD transaction slot (#31):
[ 931.196520] ------------[ cut here ]------------
[ 931.201702] mmc1: cqhci: spurious TCN for tag 31
[ 931.206906] WARNING: CPU: 0 PID: 1433 at /usr/src/kernel/drivers/mmc/host/cqhci.c:725 cqhci_irq+0x2e4/0x490
[ 931.206909] Modules linked in:
[ 931.206918] CPU: 0 PID: 1433 Comm: irq/29-mmc1 Not tainted 4.19.8-rt6-funkadelic #1
[ 931.206920] Hardware name: Theobroma Systems RK3399-Q7 SoM (DT)
[ 931.206924] pstate: 40000005 (nZcv daif -PAN -UAO)
[ 931.206927] pc : cqhci_irq+0x2e4/0x490
[ 931.206931] lr : cqhci_irq+0x2e4/0x490
[ 931.206933] sp : ffff00000e54bc80
[ 931.206934] x29: ffff00000e54bc80 x28: 0000000000000000
[ 931.206939] x27: 0000000000000001 x26: ffff000008f217e8
[ 931.206944] x25: ffff8000f02ef030 x24: ffff0000091417b0
[ 931.206948] x23: ffff0000090aa000 x22: ffff8000f008b000
[ 931.206953] x21: 0000000000000002 x20: 000000000000001f
[ 931.206957] x19: ffff8000f02ef018 x18: ffffffffffffffff
[ 931.206961] x17: 0000000000000000 x16: 0000000000000000
[ 931.206966] x15: ffff0000090aa6c8 x14: 0720072007200720
[ 931.206970] x13: 0720072007200720 x12: 0720072007200720
[ 931.206975] x11: 0720072007200720 x10: 0720072007200720
[ 931.206980] x9 : 0720072007200720 x8 : 0720072007200720
[ 931.206984] x7 : 0720073107330720 x6 : 00000000000005a0
[ 931.206988] x5 : ffff00000860d4b0 x4 : 0000000000000000
[ 931.206993] x3 : 0000000000000001 x2 : 0000000000000001
[ 931.206997] x1 : 1bde3a91b0d4d900 x0 : 0000000000000000
[ 931.207001] Call trace:
[ 931.207005] cqhci_irq+0x2e4/0x490
[ 931.207009] sdhci_arasan_cqhci_irq+0x5c/0x90
[ 931.207013] sdhci_irq+0x98/0x930
[ 931.207019] irq_forced_thread_fn+0x2c/0xa0
[ 931.207023] irq_thread+0x114/0x1c0
[ 931.207027] kthread+0x128/0x130
[ 931.207032] ret_from_fork+0x10/0x20
[ 931.207035] ---[ end trace 0000000000000002 ]---
The driver shows this message only for the first spurious interrupt
by using WARN_ONCE(). Changing this to WARN() shows, that this is
happening quite frequently (up to once a second).
Since the eMMC 5.1 specification, where CQE and CQHCI are specified,
does not mention that spurious TCN interrupts for DCMDs can be simply
ignored, we must assume that using this feature is not working reliably.
The current implementation uses DCMD for REQ_OP_FLUSH only, and
I could not see any performance/power impact when disabling
this optional feature for RK3399.
Therefore this patch disables DCMDs for RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: stable@vger.kernel.org
[the corresponding code changes are queued for 5.2 so doing that as well]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Mighty is basically the same Chromebook as Jaq but it has a full-sized
SD slot and some different (slightly more rugged) plastics around it.
Like Jaq, Mighty may show up with various different brandings but all
of them have the same board inside.
In the downstream kernel Mighty and Jaq share a "dtsi" and Mighty just
adds the SD write protect (needed for a full-sized SD slot). We'll do
this upstream by just including the Jaq dts and make the changes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Linux reads MCG_CAP[Count] to find the number of MCA banks visible to a
CPU. Currently, this number is the same for all CPUs and a warning is
shown if there is a difference. The number of banks is overwritten with
the MCG_CAP[Count] value of each following CPU that boots.
According to the Intel SDM and AMD APM, the MCG_CAP[Count] value gives
the number of banks that are available to a "processor implementation".
The AMD BKDGs/PPRs further clarify that this value is per core. This
value has historically been the same for every core in the system, but
that is not an architectural requirement.
Future AMD systems may have different MCG_CAP[Count] values per core,
so the assumption that all CPUs will have the same MCG_CAP[Count] value
will no longer be valid.
Also, the first CPU to boot will allocate the struct mce_banks[] array
using the number of banks based on its MCG_CAP[Count] value. The machine
check handler and other functions use the global number of banks to
iterate and index into the mce_banks[] array. So it's possible to use an
out-of-bounds index on an asymmetric system where a following CPU sees a
MCG_CAP[Count] value greater than its predecessors.
Thus, allocate the mce_banks[] array to the maximum number of banks.
This will avoid the potential out-of-bounds index since the value of
mca_cfg.banks is capped to MAX_NR_BANKS.
Set the value of mca_cfg.banks equal to the max of the previous value
and the value for the current CPU. This way mca_cfg.banks will always
represent the max number of banks detected on any CPU in the system.
This will ensure that all CPUs will access all the banks that are
visible to them. A CPU that can access fewer than the max number of
banks will find the registers of the extra banks to be read-as-zero.
Furthermore, print the resulting number of MCA banks in use. Do this in
mcheck_late_init() so that the final value is printed after all CPUs
have been initialized.
Finally, get bank count from target CPU when doing injection with mce-inject
module.
[ bp: Remove out-of-bounds example, passify and cleanup commit message. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20180727214009.78289-1-Yazen.Ghannam@amd.com
|
|
Describe the remaining 3 LEDs, which are driven by the first CAT9554
port expander.
Drop the superfluous status property from the leds node while at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable the I2C bus, and add the following devices:
- Two CAT9554 port expanders (8 GPIOs, interrupt not wired by
default),
- R1EX24016ASAS0A EEPROM.
The bus also contains a MAX9856 Audio Codec, which is not yet supported.
All devices (incl. the audio codec) are documented to support an I2C bus
running at 400 kHz.
Pinctrl is based on the RZ/A BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Salvator-X and XS boards have a 4 lines DIP switch and 3 push
buttons connected to SoC GPIOs, meant to be used as general-purpose test
keys. Add a corresponding node in DT, mapping (semi-randomly) the DIP
switch to keys 1-4 and the push buttons to keys A-C.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Basic audio dmac register only supports busif from 0 to 3,
in order to use busif4 ~ busif7, extended audio dmac register
need to be used.
This patch updates H3 (= r8a7795), M3-W (= r8a7796) and
M3-N (=r8a77965) to use extended audio dmac register set.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal Delay mode does'nt support
on R-Car D3. This patch fixes EthernetAVB phy mode to rgmii.
This is achieved by simply dropping the phy-mode property from
r8a77995-draak.dts as the default property for this for r8a77995,
as set in r8a77995.dtsi, is "rgmii".
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
This patch sorts the node label to improve maintainability.
The sort has been done alphabetically with the node label name as the
key.
This patch does not include functional changes.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Update Ebisu and Draak bootargs to match other boards
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler")
Fixes: ed7290d0ee8f ("x86, mce: implement new status bits")
Reported-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk
|
|
The Linux RISC-V 32bit kernel is broken after we moved setup_vm() from
kernel/setup.c to mm/init.c because Linux RISC-V 32bit kernel by default
uses cmodel=medlow which results in a non-position-independent setup_vm().
This patch fixes Linux RISC-V 32bit kernel booting by:
1. Forcing cmodel=medany for mm/init.c
2. Moving remaing MM-related stuff va_pa_offset, pfn_base and
empty_zero_page from kernel/setup.c to mm/init.c
Further, the setup_vm() cannot handle GCC instrumentation for FTRACE so
we disable it for mm/init.c by not using "-pg" compiler flag.
Fixes: 6f1e9e946f0b ("RISC-V: Move setup_vm() to mm/init.c")
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
A memory save operation to 8-byte variable in RV32 is divided into
two sw instructions in the put_user macro. The current fixup returns
execution flow to the second sw instead of the one after it.
This patch fixes this fixup code according to the load access part.
Signed-off-by: Alan Kao<alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
In cpu_to_drc_index() in the case when FW_FEATURE_DRC_INFO is absent,
we currently use of_read_property() to obtain the pointer to the array
corresponding to the property "ibm,drc-indexes". The elements of this
array are of type __be32, but are accessed without any conversion to
the OS-endianness, which is buggy on a Little Endian OS.
Fix this by using of_property_read_u32_index() accessor function to
safely read the elements of the array.
Fixes: e83636ac3334 ("pseries/drc-info: Search DRC properties for CPU indexes")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[mpe: Make the WARN_ON a WARN_ON_ONCE so it's not retriggerable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The recently added uart mux options had a few typos. Fix them.
Fixes: 43d0fe112585 ("ARM: dts: sun7i: add pinctrl for missing uart mux options")
Reported-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
We switched to the generic pinctrl binding some time ago, yet the GMAC
pinctrl node apparently slipped through. Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The I2S binding never mentions a reset-names property, or mentions which
value it should have. To avoid any further issue, remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
For dynamically allocated struct omap_hwmod data, we need to populate
the device IP specific reset quirks.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can just check for omap2 and 3 for i2c and smartreflex locally.
The rest of the .rev data is already unused.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With ti-sysc interconnect target module, we can allocate struct omap_hwmod
data based on the devicetree data. This allows dropping the static SoC
specific data eventually so we will only boot with data we actually need.
To allocate struct omap_hwmod dynamically, we need to add a mutex for
modifying the list, and remove __init for few functions.
Note that we are not initialized oh->_clk or the optional clocks and their
related quirks. That can be directly handled by the interconnect target
module driver.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For dynamically allocated struct hwmod entries probing with ti-sysc
interconnect target module driver, we need to specify the initial default
state the same way as we do for the platform data cases.
Let's prepare for that by adding _HWMOD_STATE_DEFAULT that we can then
use to set the initial default state without a need to add similar
CONFIG_PM handling in multiple places.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For dynamically allocated sysconfig data we only need to allocate a new
class for the cases where the class is shared. For dynamically allocated
struct omap_hwmod we will always allocate a new class.
Let's add detection for when we need to allocate a new class by comparing
the class name against the module name. If they match, there's no need
to allocate a new calls as we don't have case of mixed platform data and
dts data initialized modules for the same class.
Let's also move the init of class data inside the spinlock.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Only omap_hwmod_init_module() gets called, the rest of the interconnect
target module allocation functions can be static.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 747834ab8347 ("ARM: OMAP2+: hwmod: revise hardreset behavior") made
the call to _enable() conditional based on no oh->rst_lines_cnt. This
caused the return value to be potentially uninitialized. Curiously we see
no compiler warnings for this, probably as this gets inlined.
We call _setup_reset() from _setup() and only _setup_postsetup() if the
return value is zero. Currently the return value can be uninitialized for
cases where oh->rst_lines_cnt is set and HWMOD_INIT_NO_RESET is not set.
Fixes: 747834ab8347 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We must not use legacy clock defines for dts clckctrl clocks as the offsets
will be wrong.
Fixes: 87fc89ced3a7 ("ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc")
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Handle potential errors returned from kcalloc().
[ bp: rewrite commit message. ]
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Banman <abanman@hpe.com>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: pakki001@umn.edu
Cc: platform-driver-x86@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Varsha Rao <rvarsha016@gmail.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190325202924.4624-1-kjlu@umn.edu
|
|
Add basic dts support for i.MM8MM LPDDR4 EVK.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8M Mini is new SOC of the i.MX8M family. it is
focused on delivering the latest and greatest video and
audio experience combining state-of-the-art media-specific
features with high-performance processing while optimized
for lowest power consumption. The i.MX 8M Mini Media Applications
Processor is 14nm FinFET product of the growing i.MX8M family
targeting the consumer & industrial market. It is built in 14LPP
to achieve both high performance and low power consumption
and relies on a powerful fully coherent core complex based on
a quad Cortex-A53 cluster with video and graphics accelerators
This patch adds the basic dtsi support for i.MX8MM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX7ULP OCOTP support, its clock source is from
M4 BUS clock which is NOT available in Linux clock tree,
but M4 BUS clock is always ON when A7 (Linux) is alive,
so just use dummy clock here.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is one of two boards that make use of the recently introduced SIOX
bus. Apart from the devices described in the dts it features a display
with touch that I didn't include here because it needs some non-mainline
change to operate correctly.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Bjorn Andersson
Jorge Ramirez-Ortiz
Marc Gonzalez
Khasim Syed Mohammed
Vinod Koul
Georgi Djakov
Linus Torvalds
Chen Zhou
Mimi Zohar
Matteo Croce
Baoquan He
Christoph Muellner
Douglas Anderson
Yazen Ghannam
Geert Uytterhoeven
Laurent Pinchart
Jiada Wang
Kazuya Mizuguchi
Takeshi Kihara
Magnus Damm
Tony Luck
Anup Patel
Alan Kao
Gautham R. Shenoy
Mans Rullgard
Maxime Ripard
Tony Lindgren
Kangjie Lu
Jacky Bai
Anson Huang
Uwe Kleine-König