| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the Odroid-C1+ schematics the Ethernet TXD1 signal is
routed to GPIOH_5 and the TXD0 signal is routed to GPIOH_6.
The public S805 datasheet shows that TXD0 can be routed to DIF_2_P and
TXD1 can be routed to DIF_2_N instead.
The pin groups eth_txd0_0 (GPIOH_6) and eth_txd0_1 (DIF_2_P) are both
configured as Ethernet TXD0 and TXD1 data lines in meson8b.dtsi. At the
same time eth_txd1_0 (GPIOH_5) and eth_txd1_1 (DIF_2_N) are configured
as TXD0 and TXD1 data lines as well.
This results in a bad Ethernet receive performance. Presumably this is
due to the eth_txd0 and eth_txd1 signal being routed to the wrong pins.
As a result of that data can only be transmitted on eth_txd2 and
eth_txd3. However, I have no scope to fully confirm this assumption.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
Drop the eth_txd0_1 and eth_txd1_1 groups from eth_rgmii_pins to fix the
Ethernet transmit performance on Odroid-C1. Also add the eth_rxd2 and
eth_rxd3 groups so we don't rely on the bootloader to set them up.
iperf3 statistics before this change:
- transmitting from Odroid-C1: 741 Mbits/sec (0 retries)
- receiving on Odroid-C1: 199 Mbits/sec (1713 retries)
iperf3 statistics after this change:
- transmitting from Odroid-C1: 667 Mbits/sec (0 retries)
- receiving on Odroid-C1: 750 Mbits/sec (0 retries)
Fixes: b96446541d8390 ("ARM: dts: meson8b: extend ethernet controller description")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
__cmpxchg_small erroneously uses u8 for load comparison which can
be either char or short. This patch changes the local variable to
u32 which is sufficiently sized, as the loaded value is already
masked and shifted appropriately. Using an integer size avoids
any unnecessary canonicalization from use of non native widths.
This patch is part of a series that adapts the MIPS small word
atomics code for xchg and cmpxchg on short and char to RISC-V.
Cc: RISC-V Patches <patches@groups.riscv.org>
Cc: Linux RISC-V <linux-riscv@lists.infradead.org>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Signed-off-by: Michael Clark <michaeljclark@mac.com>
[paul.burton@mips.com:
- Fix varialble typo per Jonas Gorski.
- Consolidate load variable with other declarations.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3ba7f44d2b19 ("MIPS: cmpxchg: Implement 1 byte & 2 byte cmpxchg()")
Cc: stable@vger.kernel.org # v4.13+
|
|
Pull s390 bug fixes from Martin Schwidefsky:
- Fix specification exception on z196 during ap probe
- A fix for suspend-to-disk, the VMAP stack patch broke the
swsusp_arch_suspend function
- The EMC CKD ioctl of the dasd driver needs an additional size check
for user space data
- Revert an incorrect patch for the PCI base code that removed a bit
lock that turned out to be required after all
* tag 's390-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
Revert "s390/pci: remove bit_lock usage in interrupt handler"
s390/zcrypt: fix specification exception on z196 during ap probe
s390/dasd: fix using offset into zero size array error
s390/suspend: fix stack setup in swsusp_arch_suspend
|
|
User space tools which do automated task placement need information
about AVX-512 usage of tasks, because AVX-512 usage could cause core
turbo frequency drop and impact the running task on the sibling CPU.
The XSAVE hardware structure has bits that indicate when valid state
is present in registers unique to AVX-512 use. Use these bits to
indicate when AVX-512 has been in use and add per-task AVX-512 state
timestamp tracking to context switch.
Well-written AVX-512 applications are expected to clear the AVX-512
state when not actively using AVX-512 registers, so the tracking
mechanism is imprecise and can theoretically miss AVX-512 usage during
context switch. But it has been measured to be precise enough to be
useful under real-world workloads like tensorflow and linpack.
If higher precision is required, suggest user space tools to use the
PMU-based mechanisms in combination.
Signed-off-by: Aubrey Li <aubrey.li@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: aubrey.li@intel.com
Link: http://lkml.kernel.org/r/20190117183822.31333-1-aubrey.li@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When facility.76 MSAX3 is present for the guest we must issue a validity
interception if the CRYCBD is not valid.
The bit CRYCBD.31 is an effective field and tested at each guest level
and has for effect to mask the facility.76
It follows that if CRYCBD.31 is clear and AP is not in use we do not
have to test the CRYCBD validatity even if facility.76 is present in the
host.
Fixes: 6ee74098201b ("KVM: s390: vsie: allow CRYCB FORMAT-0")
Cc: stable@vger.kernel.org
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1549876849-32680-1-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Thomas noticed that the new arch/x86/include/asm/cpu_device_id.h header is
a train-wreck that didn't incorporate review feedback like not using __u8
in kernel-only headers.
While at it also fix all the *other* problems this header has:
- Use canonical names for the header guards. It's inexplicable why a non-standard
guard was used.
- Don't define the header guard to 1. Plus annotate the closing #endif as done
absolutely every other header. Again, an inexplicable source of noise.
- Move the kernel API calls provided by this header next to each other, there's
absolutely no reason to have them spread apart in the header.
- Align the INTEL_CPU_DESC() macro initializations vertically, this is easier to
read and it's also the canonical style.
- Actually name the macro arguments properly: instead of 'mod, step, rev',
spell out 'model, stepping, revision' - it's not like we have a lack of
characters in this header.
- Actually make arguments macro-safe - again it's inexplicable why it wasn't
done properly to begin with.
Quite amazing how many problems a 41 lines header can contain.
This kind of code quality is unacceptable, and it slipped through the
review net of 2 developers and 2 maintainers, including myself, until
Thomas noticed it. :-/
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Vince (and later on Ravi) reported crashes in the BTS code during
fuzzing with the following backtrace:
general protection fault: 0000 [#1] SMP PTI
...
RIP: 0010:perf_prepare_sample+0x8f/0x510
...
Call Trace:
<IRQ>
? intel_pmu_drain_bts_buffer+0x194/0x230
intel_pmu_drain_bts_buffer+0x160/0x230
? tick_nohz_irq_exit+0x31/0x40
? smp_call_function_single_interrupt+0x48/0xe0
? call_function_single_interrupt+0xf/0x20
? call_function_single_interrupt+0xa/0x20
? x86_schedule_events+0x1a0/0x2f0
? x86_pmu_commit_txn+0xb4/0x100
? find_busiest_group+0x47/0x5d0
? perf_event_set_state.part.42+0x12/0x50
? perf_mux_hrtimer_restart+0x40/0xb0
intel_pmu_disable_event+0xae/0x100
? intel_pmu_disable_event+0xae/0x100
x86_pmu_stop+0x7a/0xb0
x86_pmu_del+0x57/0x120
event_sched_out.isra.101+0x83/0x180
group_sched_out.part.103+0x57/0xe0
ctx_sched_out+0x188/0x240
ctx_resched+0xa8/0xd0
__perf_event_enable+0x193/0x1e0
event_function+0x8e/0xc0
remote_function+0x41/0x50
flush_smp_call_function_queue+0x68/0x100
generic_smp_call_function_single_interrupt+0x13/0x30
smp_call_function_single_interrupt+0x3e/0xe0
call_function_single_interrupt+0xf/0x20
</IRQ>
The reason is that while event init code does several checks
for BTS events and prevents several unwanted config bits for
BTS event (like precise_ip), the PERF_EVENT_IOC_PERIOD allows
to create BTS event without those checks being done.
Following sequence will cause the crash:
If we create an 'almost' BTS event with precise_ip and callchains,
and it into a BTS event it will crash the perf_prepare_sample()
function because precise_ip events are expected to come
in with callchain data initialized, but that's not the
case for intel_pmu_drain_bts_buffer() caller.
Adding a check_period callback to be called before the period
is changed via PERF_EVENT_IOC_PERIOD. It will deny the change
if the event would become BTS. Plus adding also the limit_period
check as well.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20190204123532.GA4794@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Enable various options in the defconfigs of both i386 and x86_64
that could do with some test coverage in automated testing. Note
that these options are typically enabled by distros as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
APEI's Generic Hardware Error Source structures do not describe
whether the SDEI event is shared or private, as this information is
discoverable via the API.
GHES needs to know whether an event is normal or critical to avoid
sharing locks or fixmap entries, but GHES shouldn't have to know about
the SDEI API.
Add a helper to register the GHES using the appropriate normal or
critical callback.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Linux 5.0-rc6
|
|
We need the debugfs fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'write' parameter is unused in gup_fast_permitted() so remove it.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20190210223424.13934-1-ira.weiny@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
A microcode patch is also needed for Goldmont while counter freezing
feature is enabled. Otherwise, there will be some issues, e.g. PMI lost.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1549319013-4522-5-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Clean up counter freezing quirk to use the new facility to check for
min microcode revisions.
Rename the counter freezing quirk related functions. Because other
platforms, e.g. Goldmont, also needs to call the quirk.
Only check the boot CPU, assuming models and features are consistent
over all CPUs.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1549319013-4522-4-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Clean up SNB PEBS quirk to use the new facility to check for min
microcode revisions.
Only check the boot CPU, assuming models and features are consistent
over all CPUs.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1549319013-4522-3-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
KVM added a workaround for PEBS events leaking into guests with
commit:
26a4f3c08de4 ("perf/x86: disable PEBS on a guest entry.")
This uses the VT entry/exit list to add an extra disable of the
PEBS_ENABLE MSR.
Intel also added a fix for this issue to microcode updates on
Haswell/Broadwell/Skylake.
It turns out using the MSR entry/exit list makes VM exits
significantly slower. The list is only needed for disabling
PEBS, because the GLOBAL_CTRL change gets optimized by
KVM into changing the VMCS.
Check for the microcode updates that have the microcode
fix for leaking PEBS, and disable the extra entry/exit list
entry for PEBS_ENABLE. In addition we always clear the
GLOBAL_CTRL for the PEBS counter while running in the guest,
which is enough to make them never fire at the wrong
side of the host/guest transition.
The overhead for VM exits with the filtering active with the patch is
reduced from 8% to 4%.
The microcode patch has already been merged into future platforms.
This patch is one-off thing. The quirks is used here.
For other old platforms which doesn't have microcode patch and quirks,
extra disable of the PEBS_ENABLE MSR is still required.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: bp@alien8.de
Link: https://lkml.kernel.org/r/1549319013-4522-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For bug workarounds or checks, it is useful to check for specific
microcode revisions.
Add a new generic function to match the CPU with stepping.
Add the other function to check the min microcode revisions for
the matched CPU.
A new table format is introduced to facilitate the quirk to
fill the related information.
This does not change the existing x86_cpu_id because it's an ABI
shared with modules, and also has quite different requirements,
as in no wildcards, but everything has to be matched exactly.
Originally-by: Andi Kleen <ak@linux.intel.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: eranian@google.com
Link: https://lkml.kernel.org/r/1549319013-4522-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The peripheral bus on the i.MX8MQ is still limited to 32bits, so
we need to declare the usable range for device DMA operations, as
the DRAM will extend across the 32bit boundary if more than 3GB
are installed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix page fault handling code to fixup r16-r18 registers.
Before the patch code had off-by-two registers bug.
This bug caused overwriting of ps,pc,gp registers instead
of fixing intended r16,r17,r18 (see `struct pt_regs`).
More details:
Initially Dmitry noticed a kernel bug as a failure
on strace test suite. Test passes unmapped userspace
pointer to io_submit:
```c
#include <err.h>
#include <unistd.h>
#include <sys/mman.h>
#include <asm/unistd.h>
int main(void)
{
unsigned long ctx = 0;
if (syscall(__NR_io_setup, 1, &ctx))
err(1, "io_setup");
const size_t page_size = sysconf(_SC_PAGESIZE);
const size_t size = page_size * 2;
void *ptr = mmap(NULL, size, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
if (MAP_FAILED == ptr)
err(1, "mmap(%zu)", size);
if (munmap(ptr, size))
err(1, "munmap");
syscall(__NR_io_submit, ctx, 1, ptr + page_size);
syscall(__NR_io_destroy, ctx);
return 0;
}
```
Running this test causes kernel to crash when handling page fault:
```
Unable to handle kernel paging request at virtual address ffffffffffff9468
CPU 3
aio(26027): Oops 0
pc = [<fffffc00004eddf8>] ra = [<fffffc00004edd5c>] ps = 0000 Not tainted
pc is at sys_io_submit+0x108/0x200
ra is at sys_io_submit+0x6c/0x200
v0 = fffffc00c58e6300 t0 = fffffffffffffff2 t1 = 000002000025e000
t2 = fffffc01f159fef8 t3 = fffffc0001009640 t4 = fffffc0000e0f6e0
t5 = 0000020001002e9e t6 = 4c41564e49452031 t7 = fffffc01f159c000
s0 = 0000000000000002 s1 = 000002000025e000 s2 = 0000000000000000
s3 = 0000000000000000 s4 = 0000000000000000 s5 = fffffffffffffff2
s6 = fffffc00c58e6300
a0 = fffffc00c58e6300 a1 = 0000000000000000 a2 = 000002000025e000
a3 = 00000200001ac260 a4 = 00000200001ac1e8 a5 = 0000000000000001
t8 = 0000000000000008 t9 = 000000011f8bce30 t10= 00000200001ac440
t11= 0000000000000000 pv = fffffc00006fd320 at = 0000000000000000
gp = 0000000000000000 sp = 00000000265fd174
Disabling lock debugging due to kernel taint
Trace:
[<fffffc0000311404>] entSys+0xa4/0xc0
```
Here `gp` has invalid value. `gp is s overwritten by a fixup for the
following page fault handler in `io_submit` syscall handler:
```
__se_sys_io_submit
...
ldq a1,0(t1)
bne t0,4280 <__se_sys_io_submit+0x180>
```
After a page fault `t0` should contain -EFALUT and `a1` is 0.
Instead `gp` was overwritten in place of `a1`.
This happens due to a off-by-two bug in `dpf_reg()` for `r16-r18`
(aka `a0-a2`).
I think the bug went unnoticed for a long time as `gp` is one
of scratch registers. Any kernel function call would re-calculate `gp`.
Dmitry tracked down the bug origin back to 2.1.32 kernel version
where trap_a{0,1,2} fields were inserted into struct pt_regs.
And even before that `dpf_reg()` contained off-by-one error.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-and-reviewed-by: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: stable@vger.kernel.org # v2.1.32+
Bug: https://bugs.gentoo.org/672040
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
Eiger machine vector definition has nr_irqs 128, and working 2.6.26
boot shows SCSI getting IRQ-s 64 and 65. Current kernel boot fails
because Symbios SCSI fails to request IRQ-s and does not find the disks.
It has been broken at least since 3.18 - the earliest I could test with
my gcc-5.
The headers have moved around and possibly another order of defines has
worked in the past - but since 128 seems to be correct and used, fix
arch/alpha/include/asm/irq.h to have NR_IRQS=128 for Eiger.
This fixes 4.19-rc7 boot on my Force Flexor A264 (Eiger subarch).
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Matt Turner <mattst88@gmail.com>
|
|
It's needed to properly reboot the i.MX8MQ EVK board.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is needed to boot correctly from eMMC on the i.MX8MQ EVK board.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the node for the ARM Performance Monitor Units.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add RTC support for i.MX8MQ.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the Freescale/NXP QuadSPI controller with a proper pinctrl set on
the i.MX8MQ EVK board.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a node for the Freescale/NXP QuadSPI controller and extend the AIPS3
memory range to accommodate the QuadSPI-memory region.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the three ECSPI ports present on i.MX8MQ.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable driver support of NXP FlexSPI controller.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable all the i.MX8MQ configs necessary to boot.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable basic drivers for imx8qxp booting up support:
SCU firmware, Mailbox(MU), SCU Power Domain/Pinctrl/Clock,
Uart, MMC, FEC.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch enables CONFIG_RTC_DRV_IMX_SC as module by default.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the stmpe-adc DT node as found on Toradex iMX6 modules
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add missing devicetree compatibles for the following LS1021A based
boards:
ls1021a-moxa-uc-8410a.dts
ls1021a-qds.dts
ls1021a-twr.dts
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A valid WEIM range configuration must specify range entries for
all four chip selects. This fixes an error on boot:
imx-weim: probe of 21b8000.weim failed with error -22
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an
i.MX6UL or i.MX6ULL SOM and various add-on boards.
The following adds support for the "Full Featured" version of the Segin,
which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation
module.
Its hardware specifications are:
* 512MB DDR3 memory
* 512MB NAND flash
* Dual 10/100 Ethernet
* USB Host and USB OTG
* RS232
* MicroSD external storage
* Audio, RS232, I2C, SPI, CAN headers
* Further I/O options via A/V and Expansion headers
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit d2d0ad2aec4a ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
These are i.MX6S/DL based SBCs embedded in various Y Soft products.
All share the same board design but have slightly different HW
configuration.
Ursa
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 1x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
Draco
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 2x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
Hydra
- i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
- I2C OLED display, capacitive matrix keys
- 2x Eth (QCA8334 switch)
- USB OTG
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
- HDMI
- miniPCIe slot
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7ULP SoC revision info is inside the SIM mode's JTAG_ID
register, add sim node to support SoC revision check.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6ULL has errata ERR010450, there is I/O timing limitation,
for SDR mode, SD card clock can't exceed 150MHz, for DDR mode,
SD card clock can't exceed 45MHz. This patch change to use the
new compatible "fsl,imx6ull-usdhc" to follow this limitation.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since imx6ulz.dtsi includes imx6ull.dtsi, we only need to fix the compatible
string here to achieve the correct OTP size for both SoCs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This was implemented in the driver but not actually defined and
referenced in dts. This makes it always on.
From reference manual in section "10.4.1.4.1 Power Distribution":
"Display domain - The DISPLAY domain contains GIS, CSI, PXP, LCDIF,
PCIe, DCIC, and LDB. It is supplied by internal regulator."
The current pd_pcie is actually only for PCIE_PHY, the PCIE ip block is
actually inside the DISPLAY domain. Handle this by adding the pcie node
in both power domains.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull y2038 - time64 system calls from Arnd Bergmann:
This series finally gets us to the point of having system calls with 64-bit
time_t on all architectures, after a long time of incremental preparation
patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures using
the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call that
includes a 'struct timespec' argument, or a structure containing a timespec
or (in case of clock_adjtime) timeval. Not included here are new versions
of getitimer/setitimer and getrusage/waitid, which are planned for the
future but only needed to make a consistent API rather than for correct
operation beyond y2038. These four system calls are based on 'timeval', and
it has not been finally decided what the replacement kernel interface will
use instead.
So far, I have done a lot of build testing across most architectures, which
has found a number of bugs. Runtime testing so far included testing LTP on
32-bit ARM with the existing system calls, to ensure we do not regress for
existing binaries, and a test with a 32-bit x86 build of LTP against a
modified version of the musl C library that has been adapted to the new
system call interface [3]. This library can be used for testing on all
architectures supported by musl-1.1.21, but it is not how the support is
getting integrated into the official musl release. Official musl support is
planned but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
|
|
Pull preparatory work for y2038 changes from Arnd Bergmann:
System call unification and cleanup
The system call tables have diverged a bit over the years, and a number of
the recent additions never made it into all architectures, for one reason
or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all architectures
but that we definitely want there. This includes {,f}statfs64() and
get{eg,eu,g,p,u,pp}id() on alpha, which have been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like what we
do on other architectures, while keeping the 31-bit pointer
extension. This was merged as a shared branch by the s390 maintainers
and is included here in order to base the other patches on top.
- Add the separate ipc syscalls on all architectures that traditionally
only had sys_ipc(). This version is done without support for IPC_OLD
that is we have in sys_ipc. The new semtimedop_time64 syscall will only
be added here, not in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably don't need
everywhere, in particular pkey_* and rseq, for the purpose of symmetry:
if it's in asm-generic/unistd.h, it makes sense to have it everywhere. I
expect that any future system calls will get assigned on all platforms
together, even when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future calls. In
combination with the generated tables, this hopefully makes it easier to
add new calls across all architectures together.
All of the above are technically separate from the y2038 work, but are done
as preparation before we add the new 64-bit time_t system calls everywhere,
providing a common baseline set of system calls.
I expect that glibc and other libraries that want to use 64-bit time_t will
require linux-5.1 kernel headers for building in the future, and at a much
later point may also require linux-5.1 or a later version as the minimum
kernel at runtime. Having a common baseline then allows the removal of many
architecture or kernel version specific workarounds.
|
|
Pull x86 fixes from Ingo Molnar:
"A handful of fixes:
- Fix an MCE corner case bug/crash found via MCE injection testing
- Fix 5-level paging boot crash
- Fix MCE recovery cache invalidation bug
- Fix regression on Xen guests caused by a recent PMD level mremap
speedup optimization"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Make set_pmd_at() paravirt aware
x86/mm/cpa: Fix set_mce_nospec()
x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()
|
|
Pull perf fixes from Ingo Molnar:
"A couple of kernel side fixes:
- Fix the Intel uncore driver on certain hardware configurations
- Fix a CPU hotplug related memory allocation bug
- Remove a spurious WARN()
... plus also a handful of perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script python: Add Python3 support to tests/attr.py
perf trace: Support multiple "vfs_getname" probes
perf symbols: Filter out hidden symbols from labels
perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
tools headers uapi: Sync linux/in.h copy from the kernel sources
perf clang: Do not use 'return std::move(something)'
perf mem/c2c: Fix perf_mem_events to support powerpc
perf tests evsel-tp-sched: Fix bitwise operator
perf/core: Don't WARN() for impossible ring-buffer sizes
perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
perf/x86/intel/uncore: Add Node ID mask
|
Martin Blumenstingl
Michael Clark
Linus Torvalds
Aubrey Li
Ingo Molnar
Pierre Morel
Jiri Olsa
Ard Biesheuvel
James Morse
Linus Walleij
Greg Kroah-Hartman
Ira Weiny
Kan Liang
Andi Kleen
Lucas Stach
Sergei Trofimovich
Meelis Roos
Carlo Caione
Abel Vesa
Fabio Estevam
Yogesh Narayan Gaur
Aisheng Dong
Anson Huang
Philippe Schenker
Manivannan Sadhasivam
Stefan Agner
Martyn Welch
Vokáč Michal
BOUGH CHEN
Stefan Wahren
Leonard Crestez
Thomas Gleixner