| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
For boot-time switching between paging modes, we need to be able to
adjust virtual mask shifts.
The change doesn't affect the kernel image size much:
text data bss dec hex filename
8628892 4734340 1368064 14731296 e0c820 vmlinux.before
8628966 4734340 1368064 14731370 e0c86a vmlinux.after
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-9-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For boot-time switching between paging modes, we need to be able to
adjust size of physical address space at runtime.
As part of making physical address space size variable, we have to make
X86_5LEVEL dependent on SPARSEMEM_VMEMMAP. !SPARSEMEM_VMEMMAP
configuration doesn't build with variable MAX_PHYSMEM_BITS.
For !SPARSEMEM_VMEMMAP SECTIONS_WIDTH depends on MAX_PHYSMEM_BITS:
SECTIONS_WIDTH
SECTIONS_SHIFT
MAX_PHYSMEM_BITS
And SECTIONS_WIDTH is used on pre-processor stage, it doesn't work if it's
dyncamic. See include/linux/page-flags-layout.h.
Effect on kernel image size:
text data bss dec hex filename
8628393 4734340 1368064 14730797 e0c62d vmlinux.before
8628892 4734340 1368064 14731296 e0c820 vmlinux.after
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-8-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
For boot-time switching between 4- and 5-level paging we need to be able
to fold p4d page table level at runtime. It requires variable
PGDIR_SHIFT and PTRS_PER_P4D.
The change doesn't affect the kernel image size much:
text data bss dec hex filename
8628091 4734304 1368064 14730459 e0c4db vmlinux.before
8628393 4734340 1368064 14730797 e0c62d vmlinux.after
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-7-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
LDT_BASE_ADDR has different value in 4- and 5-level paging
configurations.
We need to make it dynamic in preparation for boot-time switching
between paging modes.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-6-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The new flag would indicate what paging mode we are in.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-5-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We need to be able to adjust virtual memory layout at runtime to be able
to switch between 4- and 5-level paging at boot-time.
KASLR already has movable __VMALLOC_BASE, __VMEMMAP_BASE and __PAGE_OFFSET.
Let's re-use it.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-4-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
With boot-time switching between paging mode we will have variable
MAX_PHYSMEM_BITS.
Let's use the maximum variable possible for CONFIG_X86_5LEVEL=y
configuration to define zsmalloc data structures.
The patch introduces MAX_POSSIBLE_PHYSMEM_BITS to cover such case.
It also suits well to handle PAE special case.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-3-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
__PHYSICAL_MASK_SHIFT is used to define the mask that helps to extract
physical address from a page table entry.
Although real physical address space available may differ between
machines, it's safe to use 52 as __PHYSICAL_MASK_SHIFT. Unused bits
above log2(MAXPHYADDR) up to bit 51 are reserved and must be 0.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180214111656.88514-2-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the guest runs with bp isolation when doing a SIE instruction,
we must also run the nested guest with bp isolation when emulating
that SIE instruction.
This is done by activating BPBC in the lpar, which acts as an override
for lower level guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
A 'C' was missing in the model name, this patch fixes it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add description of the J25 and J27 UART headers of the Macchiatobin. They use
uart peripherals that the CP0 (J25) and CP1 (J27) provide.
Even though J25 and J27 are labeled as UART header, the pins on these headers
can be muxed for other purposes. But the UART functionality is useful when the
board is mounted in an ATX style enclosure, since the console UART is not
accessible through the microUSB at CON9.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The CP110 component has 4 uart peripherals. All of them use the same clock
gate for slow peripherals that is shared with the i2c and spi peripherals.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the I2C controller
used on the Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
commit 1534156e999735fe0befad958e1447600c0c20e7 ("i2c: mv64xxx: Fix clock
resource by adding an optional bus clock")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This extra clock is needed to access the registers of the SPI controller
used on Armada 7K/8K SoCs.
This follows the changes already made in the binding documentation (as
well as in the driver) in:
'commit 92ae112e477ac412decc3fdd5c1eeb6c90c266b4 ("spi: orion: Fix clock
resource by adding an optional bus clock")'.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Enable cdn_dp and create a cdn-dp-sound for the DP audio. Delete the
endpoints between dp and vopL for gru, since we want the DP only use
VOP big, which can support 4K mode.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[dropped vop-hacks]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add a node for the cdn DP controller which is embedded in the rk3399
SoC.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[fixed whitespaces instead of tabs, dropped unnecessary address+size-cells
and fixed the number of interrupt cells]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
If GISA is available, we do not have to kick CPUs out of SIE to deliver
interrupts. The hardware can deliver such interrupts while running.
Cc: Michael Mueller <mimu@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
For interrupt injection of floating interrupts we queue the interrupt
either in the GISA or in the floating interrupt list. The first CPU
that looks at these data structures - either in KVM code or hardware
will then deliver that interrupt. To minimize latency we also:
-a: choose a VCPU to deliver that interrupt. We prefer idle CPUs
-b: we wake up the host thread that runs the VCPU
-c: set an I/O intervention bit for that CPU so that it exits guest
context as soon as the PSW I/O mask is enabled
This will make sure that this CPU will execute the interrupt delivery
code of KVM very soon.
We can now optimize the injection case if we have exitless interrupts.
The wakeup is still necessary in case the target CPU sleeps. We can
avoid the I/O intervention request bit though. Whenever this
intervention request would be handled, the hardware could also directly
inject the interrupt on that CPU, no need to go through the interrupt
injection loop of KVM.
Cc: Michael Mueller <mimu@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Soc nodes are used in other exynos DTS. Exynos4412 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Soc nodes are used in other exynos DTS. Exynos4210 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Soc nodes are used in other exynos DTS. Exynos4 boards should use them
as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The exynos5440 device tree is the only one left, which does not use
"soc" node. Add a "soc" node to exynos5440.dtsi in order to make it
consistent with other exynos DTS.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In order to use soc node, we need to reference soc child nodes by label
in exynos4412. Define pmu label in exynos4.dtsi. Use it in exynos4412
instead of redefining the node by full path.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The exynos-syscon-restart.dtsi is already included by exynos5.dtsi
(through exynos54xx.dtsi).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Extend camera node by label, not by full path in Exynos
4412 Itop Elite. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera and i2c1_isp nodes by labels, not by full path in Exynos
4412 Trats2. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera node by label, not by full path in Exynos 4412 Odroid
boards. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera node by label, not by full path in Exynos 4412 DTSI.
This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera, fimc, mct and sysram nodes by labels, not by full path in
Exynos 4210 Universal C210 board. This avoids error-prone redefinition
of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera and fimc nodes by labels, not by full path in Exynos
4210 Trats board. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Extend camera, mixer and tmu nodes by labels, not by full path in Exynos
4210 DTSI. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Pull MIPS fix from James Hogan:
"A single change (and associated DT binding update) to allow the
address of the MIPS Cluster Power Controller (CPC) to be chosen by DT,
which allows SMP to work on generic MIPS kernels where the bootloader
hasn't configured the CPC address (i.e. the new Ranchu platform)"
* tag 'mips_4.16_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: CPC: Map registers using DT in mips_cpc_default_phys_base()
dt-bindings: Document mti,mips-cpc binding
|
|
Define pinctrl labels in exynos4412.dtsi and use them in
exynos4412-pinctrl.dtsi, as it is done in other Exynos DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
After alternatives were shifted to the call site, only 2 headers are
necessary.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180113190648.GB23111@avx2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
All clear_page() implementations use XOR which resets flags.
Judging by allyesconfig disassembly no code is affected.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180113185048.GA23111@avx2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Since CONFIG_X86_64 selects CONFIG_X86_LOCAL_APIC, the following
condition:
#if defined(CONFIG_X86_64) || defined(CONFIG_X86_LOCAL_APIC)
is equivalent to:
#if defined(CONFIG_X86_LOCAL_APIC)
... and we can eliminate that #ifdef by providing an empty
init_bsp_APIC() stub in the !CONFIG_X86_LOCAL_APIC case.
Also add some comments to explain why we call init_bsp_APIC().
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mroos@linux.ee
Cc: ville.syrjala@linux.intel.com
Link: http://lkml.kernel.org/r/20180117073748.23905-1-douly.fnst@cn.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
set_x2apic_phys_mode() is only called as part of early_param()
initialization - so mark it as __init.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180117034543.26723-1-douly.fnst@cn.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #v3.18
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The node is referred to as a DAI from the sound node and should
therefore have a #sound-dai-cells property.
Fixes: 21dd0ece34c2 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The lvds encoder chip was omitted by oversight. Add it.
Fixes: 0e4323899973 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The nattis currently relies on the cmdline to correctly configure the
MTD partition table, and the one given in the device tree is simply
ignored. Which is fortunate, since the device tree partition table is
bonkers and does not match reality.
So, in order to avoid confusion, fix the device tree partition table
to match what is expected (i.e. what is normally provided on the cmdline).
In particular, the rootfs partition should be mtd6.
Fixes: 0e4323899973 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
Joonas Kylmälä
Icenowy Zheng
Kirill A. Shutemov
Christian Borntraeger
Baruch Siach
Gregory CLEMENT
Chris Zhong
Viresh Kumar
Maciej Purski
Krzysztof Kozlowski
Linus Torvalds
Alexey Dobriyan
Dou Liyang
Geert Uytterhoeven
Bartosz Golaszewski
Santiago Esteban
Peter Rosin