| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After commit '06c47e6286d usb: dwc3: of-simple: Add support to get resets
for the device' you can add the reset property to the dwc3 node, the reset
is required for the controller to work properly, otherwise bind / unbind
stress testing of the USB controller on rk3399 we'd often end up with lots
of failures that looked like this:
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The aclk_usb3 must be enabled to support USB3 for rk3399.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the usb3 power-domain, its qos area and assign it to the usb device
node.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Debian does not ship a 'mkisofs' symlink to genisoimage. All modern
distros ship genisoimage, so just use that directly. That requires
renaming the 'genisoimage' function. Also neaten up the 'for' loop
while I'm in here.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commits 5c9d2d5c269c, c7da82b894e9, and e7fe7b5cae90.
We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.
Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was. Dave
Hansen says:
"So, the underlying bug here is that we now a get_user_pages_remote()
and then go ahead and do the p*_access_permitted() checks against the
current PKRU. This was introduced recently with the addition of the
new p??_access_permitted() calls.
We have checks in the VMA path for the "remote" gups and we avoid
consulting PKRU for them. This got missed in the pkeys selftests
because I did a ptrace read, but not a *write*. I also didn't
explicitly test it against something where a COW needed to be done"
It's also not entirely clear that it makes sense to check the protection
key bits at this level at all. But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.
We'll see.
Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back. Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b76f7 ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add reset DT node for Amlogic's Meson-AXG SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
CFL was missing from intel_early_ids[]. The PCI ID needs to be there to
allow the memory region to be stolen, otherwise we could have RAM being
arbitrarily overwritten if for example we keep using the UEFI framebuffer,
depending on how BIOS has set up the e820 map.
Fixes: b056f8f3d6b9 ("drm/i915/cfl: Add Coffee Lake PCI IDs for S Skus.")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Cc: <stable@vger.kernel.org> # v4.13+ 0890540e21cf drm/i915: add GT number to intel_device_info
Cc: <stable@vger.kernel.org> # v4.13+ 41693fd52373 drm/i915/kbl: Change a KBL pci id to GT2 from GT1.5
Cc: <stable@vger.kernel.org> # v4.13+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213200425.2954-1-lucas.demarchi@intel.com
|
|
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
|
|
Pull arm64 fixes from Will Deacon:
"There are some significant fixes in here for FP state corruption,
hardware access/dirty PTE corruption and an erratum workaround for the
Falkor CPU.
I'm hoping that things finally settle down now, but never say never...
Summary:
- Fix FPSIMD context switch regression introduced in -rc2
- Fix ABI break with SVE CPUID register reporting
- Fix use of uninitialised variable
- Fixes to hardware access/dirty management and sanity checking
- CPU erratum workaround for Falkor CPUs
- Fix reporting of writeable+executable mappings
- Fix signal reporting for RAS errors"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fpsimd: Fix copying of FP state from signal frame into task struct
arm64/sve: Report SVE to userspace via CPUID only if supported
arm64: fix CONFIG_DEBUG_WX address reporting
arm64: fault: avoid send SIGBUS two times
arm64: hw_breakpoint: Use linux/uaccess.h instead of asm/uaccess.h
arm64: Add software workaround for Falkor erratum 1041
arm64: Define cputype macros for Falkor CPU
arm64: mm: Fix false positives in set_pte_at access/dirty race detection
arm64: mm: Fix pte_mkclean, pte_mkdirty semantics
arm64: Initialise high_memory global variable earlier
|
|
Add PWM DT info for the Amlogic's Meson-Axg SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: dropped unnecessary include]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- fix the s2ram regression related to confusion around segment
register restoration, plus related cleanups that make the code more
robust
- a guess-unwinder Kconfig dependency fix
- an isoimage build target fix for certain tool chain combinations
- instruction decoder opcode map fixes+updates, and the syncing of
the kernel decoder headers to the objtool headers
- a kmmio tracing fix
- two 5-level paging related fixes
- a topology enumeration fix on certain SMP systems"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Resync objtool's instruction decoder source code copy with the kernel's latest version
x86/decoder: Fix and update the opcodes map
x86/power: Make restore_processor_context() sane
x86/power/32: Move SYSENTER MSR restoration to fix_processor_context()
x86/power/64: Use struct desc_ptr for the IDT in struct saved_context
x86/unwinder/guess: Prevent using CONFIG_UNWINDER_GUESS=y with CONFIG_STACKDEPOT=y
x86/build: Don't verify mtools configuration file for isoimage
x86/mm/kmmio: Fix mmiotrace for page unaligned addresses
x86/boot/compressed/64: Print error if 5-level paging is not supported
x86/boot/compressed/64: Detect and handle 5-level paging at boot-time
x86/smpboot: Do not use smp_num_siblings in __max_logical_packages calculation
|
|
Try to add Hiubus DT info, and also enable clock DT info
for the Amlogic's Meson-AXG SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Pull xen fixes from Juergen Gross:
"Two minor fixes for running as Xen dom0:
- when built as 32 bit kernel on large machines the Xen LAPIC
emulation should report a rather modern LAPIC in order to support
enough APIC-Ids
- The Xen LAPIC emulation is needed for dom0 only, so build it only
for kernels supporting to run as Xen dom0"
* tag 'for-linus-4.15-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: XEN_ACPI_PROCESSOR is Dom0-only
x86/Xen: don't report ancient LAPIC version
|
|
When LD_ABS/IND is used in the program, and we have a BPF helper
call that changes packet data (bpf_helper_changes_pkt_data() returns
true), then in case of sparc JIT, we try to reload cached skb data
from bpf2sparc[BPF_REG_6]. However, there is no such guarantee or
assumption that skb sits in R6 at this point, all helpers changing
skb data only have a guarantee that skb sits in R1. Therefore,
store BPF R1 in L7 temporarily and after procedure call use L7 to
reload cached skb data. skb sitting in R6 is only true at the time
when LD_ABS/IND is executed.
Fixes: 7a12b5031c6b ("sparc64: Add eBPF JIT.")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The assumption of unconditionally reloading skb pointers on
BPF helper calls where bpf_helper_changes_pkt_data() holds
true is wrong. There can be different contexts where the helper
would enforce a reload such as in case of XDP. Here, we do
have a struct xdp_buff instead of struct sk_buff as context,
thus this will access garbage.
JITs only ever need to deal with cached skb pointer reload
when ld_abs/ind was seen, therefore guard the reload behind
SEEN_SKB.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The assumption of unconditionally reloading skb pointers on
BPF helper calls where bpf_helper_changes_pkt_data() holds
true is wrong. There can be different contexts where the
BPF helper would enforce a reload such as in case of XDP.
Here, we do have a struct xdp_buff instead of struct sk_buff
as context, thus this will access garbage.
JITs only ever need to deal with cached skb pointer reload
when ld_abs/ind was seen, therefore guard the reload behind
SEEN_SKB only. Tested on s390x.
Fixes: 9db7f2b81880 ("s390/bpf: recache skb->data/hlen for skb_vlan_push/pop")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have
leading 0s
Converted using the following command:
$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 9de52a755cfb6da5 ("arm64: fpsimd: Fix failure to restore FPSIMD
state after signals") fixed an issue reported in our FPSIMD signal
restore code but inadvertently introduced another issue which tends to
manifest as random SEGVs in userspace.
The problem is that when we copy the struct fpsimd_state from the kernel
stack (populated from the signal frame) into the struct held in the
current thread_struct, we blindly copy uninitialised stack into the
"cpu" field, which means that context-switching of the FP registers is
no longer reliable.
This patch fixes the problem by copying only the user_fpsimd member of
struct fpsimd_state. We should really rework the function prototypes
to take struct user_fpsimd_state * instead, but let's just get this
fixed for now.
Cc: Dave Martin <Dave.Martin@arm.com>
Fixes: 9de52a755cfb6da5 ("arm64: fpsimd: Fix failure to restore FPSIMD state after signals")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Using PGDIR_SHIFT to identify espfix64 addresses on 5-level systems
was wrong, and it resulted in panics due to unhandled double faults.
Use P4D_SHIFT instead, which is correct on 4-level and 5-level
machines.
This fixes a panic when running x86 selftests on 5-level machines.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: 1d33b219563f ("x86/espfix: Add support for 5-level paging")
Link: http://lkml.kernel.org/r/24c898b4f44fdf8c22d93703850fb384ef87cfdc.1513035461.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add pin control information for the NAND flash interface.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The board has a regular-sized HDMI connector, so enable the display
the pipeline and HDMI output for it.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 I2C controllers under the standard bus. There is one
more in the R_ block section. The pin functions for the 3 controllers
are on PH 0~6. I2C2 can also be used on pins PE14 and PE15, but these
pins can also mux the CSI (camera sensor interface) controller's
embedded I2C controller. The latter seems to be preferred in the
reference designs for I2C camera sensor access, freeing I2C2 for other
uses.
This patch adds device nodes for the three standard I2C controllers,
as well as pinmux settings for the PH pins. For I2C0 and I2C1, since
they only have one possible setting, just set them by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 I2S controllers. The first is multiplexed with the TDM
controller. The pins are generally connected to the codec side of the
AXP81x PMIC/codec/RTC chip. The second is free for other uses. The
third only supports output, and is connected internally to the HDMI
controller for HDMI audio output.
This patch adds device nodes for the controllers, and a default pinmux
setting for the second controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
With CONFIG_PREEMPT=y there is a possible race in disable_sacf_uaccess.
The new set_fs value needs to be stored the the task structure first,
the control register update needs to be second. Otherwise a preemptive
schedule may interrupt the code right after the control register update
has been done and the next time the task is scheduled we get an incorrect
value in the control register due to the old set_fs setting.
Fixes: 0aaba41b58 ("s390: remove all code using the access register mode")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Update x86-opcode-map.txt based on the October 2017 Intel SDM publication.
Fix INVPID to INVVPID.
Add UD0 and UD1 instruction opcodes.
Also sync the objtool and perf tooling copies of this file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/aac062d7-c0f6-96e3-5c92-ed299e2bd3da@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
My previous attempt to fix a couple of bugs in __restore_processor_context():
5b06bbcfc2c6 ("x86/power: Fix some ordering bugs in __restore_processor_context()")
... introduced yet another bug, breaking suspend-resume.
Rather than trying to come up with a minimal fix, let's try to clean it up
for real. This patch fixes quite a few things:
- The old code saved a nonsensical subset of segment registers.
The only registers that need to be saved are those that contain
userspace state or those that can't be trivially restored without
percpu access working. (On x86_32, we can restore percpu access
by writing __KERNEL_PERCPU to %fs. On x86_64, it's easier to
save and restore the kernel's GSBASE.) With this patch, we
restore hardcoded values to the kernel state where applicable and
explicitly restore the user state after fixing all the descriptor
tables.
- We used to use an unholy mix of inline asm and C helpers for
segment register access. Let's get rid of the inline asm.
This fixes the reported s2ram hangs and make the code all around
more logical.
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Fixes: 5b06bbcfc2c6 ("x86/power: Fix some ordering bugs in __restore_processor_context()")
Link: http://lkml.kernel.org/r/398ee68e5c0f766425a7b746becfc810840770ff.1513286253.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
x86_64 restores system call MSRs in fix_processor_context(), and
x86_32 restored them along with segment registers. The 64-bit
variant makes more sense, so move the 32-bit code to match the
64-bit code.
No side effects are expected to runtime behavior.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Link: http://lkml.kernel.org/r/65158f8d7ee64dd6bbc6c1c83b3b34aaa854e3ae.1513286253.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
x86_64's saved_context nonsensically used separate idt_limit and
idt_base fields and then cast &idt_limit to struct desc_ptr *.
This was correct (with -fno-strict-aliasing), but it's confusing,
served no purpose, and required #ifdeffery. Simplify this by
using struct desc_ptr directly.
No change in functionality.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Link: http://lkml.kernel.org/r/967909ce38d341b01d45eff53e278e2728a3a93a.1513286253.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the sor1_out clock instead of sor1_src. This is a more accurate
model of the hardware and allows for more complicated configurations
such as HDMI 2.0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The write-protect GPIO has an active high polarity.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Reported by syzkaller:
WARNING: CPU: 0 PID: 27962 at arch/x86/kvm/emulate.c:5631 x86_emulate_insn+0x557/0x15f0 [kvm]
Modules linked in: kvm_intel kvm [last unloaded: kvm]
CPU: 0 PID: 27962 Comm: syz-executor Tainted: G B W 4.15.0-rc2-next-20171208+ #32
Hardware name: Intel Corporation S1200SP/S1200SP, BIOS S1200SP.86B.01.03.0006.040720161253 04/07/2016
RIP: 0010:x86_emulate_insn+0x557/0x15f0 [kvm]
RSP: 0018:ffff8807234476d0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff88072d0237a0 RCX: ffffffffa0065c4d
RDX: 1ffff100e5a046f9 RSI: 0000000000000003 RDI: ffff88072d0237c8
RBP: ffff880723447728 R08: ffff88072d020000 R09: ffffffffa008d240
R10: 0000000000000002 R11: ffffed00e7d87db3 R12: ffff88072d0237c8
R13: ffff88072d023870 R14: ffff88072d0238c2 R15: ffffffffa008d080
FS: 00007f8a68666700(0000) GS:ffff880802200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000002009506c CR3: 000000071fec4005 CR4: 00000000003626f0
Call Trace:
x86_emulate_instruction+0x3bc/0xb70 [kvm]
? reexecute_instruction.part.162+0x130/0x130 [kvm]
vmx_handle_exit+0x46d/0x14f0 [kvm_intel]
? trace_event_raw_event_kvm_entry+0xe7/0x150 [kvm]
? handle_vmfunc+0x2f0/0x2f0 [kvm_intel]
? wait_lapic_expire+0x25/0x270 [kvm]
vcpu_enter_guest+0x720/0x1ef0 [kvm]
...
When CS.L is set, vcpu should run in the 64 bit paging mode.
Current kvm set_sregs function doesn't have such check when
userspace inputs sreg values. This will lead unexpected behavior.
This patch is to add checks for CS.L, EFER.LME, EFER.LMA and
CR4.PAE when get SREG inputs from userspace in order to avoid
unexpected behavior.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Tianyu Lan <tianyu.lan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull PCI fixes from Bjorn Helgaas:
- add a pci_get_domain_bus_and_slot() stub for the CONFIG_PCI=n case to
avoid build breakage in the v4.16 merge window if a
pci_get_bus_and_slot() -> pci_get_domain_bus_and_slot() patch gets
merged before the PCI tree (Randy Dunlap)
- fix an AMD boot regression in the 64bit BAR support added in v4.15
(Christian König)
- fix an R-Car use-after-free that causes a crash if no PCIe card is
present (Geert Uytterhoeven)
* tag 'pci-v4.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Fix use-after-free in probe error path
x86/PCI: Only enable a 64bit BAR on single-socket AMD Family 15h
x86/PCI: Fix infinite loop in search for 64bit BAR placement
PCI: Add pci_get_domain_bus_and_slot() stub
|
|
In testing, we found that nfsd threads may call set_groups in parallel
for the same entry cached in auth.unix.gid, racing in the call of
groups_sort, corrupting the groups for that entry and leading to
permission denials for the client.
This patch:
- Make groups_sort globally visible.
- Move the call to groups_sort to the modifiers of group_info
- Remove the call to groups_sort from set_groups
Link: http://lkml.kernel.org/r/20171211151420.18655-1-thiago.becker@gmail.com
Signed-off-by: Thiago Rafael Becker <thiago.becker@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
EXYNOS_IOMMU is disabled in exynos_defconfig since it was known to cause
boot failures on Exynos Chromebooks. The recommendation was for IOMMU to
be enabled manually on systems as needed.
A recent exynos_drm change added a warning message when EXYNOS_IOMMU is
disabled. It is necessary to enable it to avoid the warning messages.
A few initial tests have shown that enabling EXYNOS_IOMMU might be safe
on Exynos Chrome-books.
Due to some other changes in the order of operations during boot
process, power domains are initialized very early and because of the
temporary lack of devices (which are not yet added to the system), are
turned off.
This practically stops FIMD for scanning framebuffer very early during
boot, before IOMMU gets initialized and "solves" the issue, which was
the reason to disable Exynos IOMMU by default on Exynos Snow Chromebooks.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Extend message with Marek Szyprowski's explanation]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add nodes for the True Random Number Generator found in Samsung Exynos
5250+ SoCs.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
We are now using clock drivers in driver/clk/ti for enabling and disabling
modules and these are all unused.
Let's also remove the related unused defines in cm-regbits-24xx.h and
cm-regbits-34xx.h.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently, the SVE field in ID_AA64PFR0_EL1 is visible
unconditionally to userspace via the CPU ID register emulation,
irrespective of the kernel config. This means that if a kernel
configured with CONFIG_ARM64_SVE=n is run on SVE-capable hardware,
userspace will see SVE reported as present in the ID regs even
though the kernel forbids execution of SVE instructions.
This patch makes the exposure of the SVE field in ID_AA64PFR0_EL1
conditional on CONFIG_ARM64_SVE=y.
Since future architecture features are likely to encounter a
similar requirement, this patch adds a suitable helper macros for
use when declaring config-conditional ID register fields.
Fixes: 43994d824e84 ("arm64/sve: Detect SVE and activate runtime support")
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Fix that bananapi-r2 booting from SD-card would fail since incorrect
polarity is applied to the previous setup with GPIO_ACTIVE_HIGH.
Cc: stable@vger.kernel.org
Fixes: 0eed8d097612 ("arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The current mmc related nodes should be falling back to MT2701
as the dt-binding defines and which has more appropriate setup
for MT7623.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The hifsys and ethsys needs the definition of the reset-cells
property. Fix this.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The ethsys binding misses the reset-cells, this patch
adds this property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
In ptdump_check_wx(), we pass walk_pgd() a start address of 0 (rather
than VA_START) for the init_mm. This means that any reported W&X
addresses are offset by VA_START, which is clearly wrong and can make
them appear like userspace addresses.
Fix this by telling the ptdump code that we're walking init_mm starting
at VA_START. We don't need to update the addr_markers, since these are
still valid bounds regardless.
Cc: <stable@vger.kernel.org>
Fixes: 1404d6f13e47 ("arm64: dump: Add checking for writable and exectuable pages")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Add clock controller drivers for Amlogic Meson-AXG SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
After the vcpu_load/vcpu_put pushdown, the handling of asynchronous VCPU
ioctl is already much clearer in that it is obvious that they bypass
vcpu_load and vcpu_put.
However, it is still not perfect in that the different state of the VCPU
mutex is still hidden in the caller. Separate those ioctls into a new
function kvm_arch_vcpu_async_ioctl that returns -ENOIOCTLCMD for more
"traditional" synchronous ioctls.
Cc: James Hogan <jhogan@kernel.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the calls to vcpu_load() and vcpu_put() in to the architecture
specific implementations of kvm_arch_vcpu_ioctl() which dispatches
further architecture-specific ioctls on to other functions.
Some architectures support asynchronous vcpu ioctls which cannot call
vcpu_load() or take the vcpu->mutex, because that would prevent
concurrent execution with a running VCPU, which is the intended purpose
of these ioctls, for example because they inject interrupts.
We repeat the separate checks for these specifics in the architecture
code for MIPS, S390 and PPC, and avoid taking the vcpu->mutex and
calling vcpu_load for these ioctls.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_set_fpu().
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
Enric Balletbo i Serra
Matthew Wilcox
Linus Torvalds
Yixun Lan
Lucas De Marchi
Jian Hu
Xingyu Chen
Qiufang Dai
Daniel Borkmann
Peter Ujfalusi
Mathieu Malaterre
Will Deacon
Andy Lutomirski
Sean Nyekjaer
Tuomas Tynkkynen
Chen-Yu Tsai
Martin Schwidefsky
Randy Dunlap
Thierry Reding
Lan Tianyu
Thiago Rafael Becker
Shuah Khan
Łukasz Stelmach
Tony Lindgren
Dave Martin
Sean Wang
Matthias Brugger
Mark Rutland
Paolo Bonzini
Christoffer Dall