| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull GPIO fixes from Linus Walleij:
"All but one are long-standing bug fixes that are also tagged for
stable
- Driver bug fixes for SH PFC, TWL4030, MSM and RCAR.
- Update the MAINTAINERS"
* tag 'gpio-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rcar: Fix level interrupt handling
gpio: msm: Fix irq mask/unmask by writing bits instead of numbers
gpio: twl4030: Fix regression for twl gpio LED output
sh-pfc: Fix PINMUX_GPIO macro
MAINTAINERS: update GPIO maintainers entry
|
|
According to the manual, if a port is set for level detection using
the corresponding bit in the edge/level select register and an external
level interrupt signal is asserted, the corresponding bit in INTDT
does not use the FF to hold the input.
Thus, writing 1 to the corresponding bits in INTCLR cannot clear the
corresponding bits in the INTDT register. Instead, when an external
input signal is stopped, the corresponding bit in INTDT is cleared
automatically.
Since the INTDT bit cannot be cleared for the level interrupts until
the interrupt signal is stopped, we end up with the infinite loop
when using deferred (threaded) IRQ handling.
Since a deferred interrupt is disabled by the low-level handler and
re-enabled only when the deferred handler is completed, Fix the issue
by dropping disabled interrupts from the pending mask as suggested by
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Changes in V2:
* Drop disabled interrupts from pending mask altogether instead of
dropping level interrupts one by one once they get handled.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We should be writing bits here but instead we're writing the
numbers that correspond to the bits we want to write. Fix it by
wrapping the numbers in the BIT() macro. This fixes gpios acting
as interrupts.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 0b2aa8be introduced a regression that causes failure
in setting LED GPO direction to OUT.
This causes USB host probe failures for Beagleboard C4.
platform usb_phy_gen_xceiv.2: Driver usb_phy_gen_xceiv requests probe deferral
hsusb2_vcc: Failed to request enable GPIO510: -22
reg-fixed-voltage reg-fixed-voltage.0.auto: Failed to register regulator: -22
reg-fixed-voltage: probe of reg-fixed-voltage.0.auto failed with error -22
direction_out/direction_in must return 0 if the operation succeeded.
Also, don't update direction flag and output data if twl4030_set_gpio_direction()
failed inside twl_direction_out();
Cc: stable@vger.kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A rather big fix for a regression where we have dropped omap4 hwmod
data earlier but are not initializing it from device tree. In addition
to this fix we eventually also be fix the issues in the .dts files
and drivers, but that's too intrusive for the -rc cycle and must be
done later on.
Also a fix for a regression where we now are wrongly trying to initialize
devices on secure omaps like n900 and n9* when booted using device tree.
We need to set aes, sham and timer12 to disabled mode for secure
devices as they are claimed by the firmware running in the secure mode.
And two more legacy booting vs device tree based booting fixes for
am3517 that I did not notice earlier until Nishant Menon reported
these to me few days ago. With these we're good to go having v3.13
working both for legacy booting and device tree based booting, and we
can then go ahed and drop the legacy booting for mach-omap2 for v3.14.
* tag 'omap-for-v3.13/yet-more-dt-regressions-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (494 commits)
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
+Linux 3.13-rc3
|
|
From Sekhar Nori:
This pull request contains a fixe for broken unbanked
GPIO IRQ support and a fix for some random memory
corruption. The bugs were introduced during v3.13
merge window.
* tag 'davinci-fixes-for-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
|
|
It's the drivers responsibility to react on failure to get
the gpio descriptors and not the frameworks. Since there are
some common peripherals that may or may not have certain
pins connected to gpio lines, depending on the platform,
printing the warning there may end up generating useless bug
reports.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Cc: stable@vger.kernel.org
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For platforms that use device tree or ACPI as the standard way to look
GPIOs up, allow the platform-defined GPIO mappings to be used as a
fallback. This may be useful for platforms that need extra GPIOs mappings
not defined by the firmware.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A typo resulted in GPIO lookup failing unconditionally.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull GPIO fixes from Linus Walleij:
"Here us a bunch of patches for the v3.13 series. Most important stuff
is related to fixes and documentation for the new GPIO descriptor API.
If the diffstat is scary you'll notice most of it is to
Documentation/*:
- A big slew of documentation for the gpiod transition that happened
in the merge window, no semantic effect, but we should provide
proper documentation with the new API.
- Fix flags related to the new API.
- Fix to the find_chip_by_name() lookup function related to the new
API.
- Fix of_find_gpio() when not using device tree.
- Bug fix for the TB10x direction setting.
- Error path fixes from Dan Carpenter.
- Nasty IRQdomain bug relating to taking an unitialized spinlock.
- Minor fixes here and there"
* tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: bcm281xx: Fix return value of bcm_kona_gpio_get()
gpio: pl061: move irqdomain initialization
gpio: ucb1400: Add MODULE_ALIAS
gpiolib: fix of_find_gpio() when OF not defined
gpio: fix memory leak in error path
gpio: rcar: NULL dereference on error in probe()
gpio: msm: make msm_gpio.summary_irq signed for error handling
gpio: mvebu: make mvchip->irqbase signed for error handling
gpiolib: use dedicated flags for GPIO properties
gpiolib: fix find_chip_by_name()
Documentation: gpiolib: document new interface
gpio: tb10x: Set output value before setting direction to output
|
|
We need to return the corresponding bit for a particular GPIO. This bit
contains shift not mask.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The PL061 driver had the irqdomain initialization in an unfortunate
place: when used with device tree (and thus passing the base IRQ
0) the driver would work, as this registers an irqdomain and waits
for mappings to be done dynamically as the devices request their
IRQs, whereas when booting using platform data the irqdomain core
would attempt to allocate IRQ descriptors dynamically (which works
fine) but also to associate the irq_domain_associate_many() on all
IRQs, which in turn will call the mapping function which at this
point will try to set the type of the IRQ and then tries to acquire
a non-initialized spinlock yielding a backtrace like this:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc1+ #652
Backtrace:
[<c0016f0c>] (dump_backtrace) from [<c00172ac>] (show_stack+0x18/0x1c)
r6:c798ace0 r5:00000000 r4:c78257e0 r3:00200140
[<c0017294>] (show_stack) from [<c0329ea0>] (dump_stack+0x20/0x28)
[<c0329e80>] (dump_stack) from [<c004fa80>] (__lock_acquire+0x1c0/0x1b80)
[<c004f8c0>] (__lock_acquire) from [<c0051970>] (lock_acquire+0x6c/0x80)
r10:00000000 r9:c0455234 r8:00000060 r7:c047d798 r6:600000d3 r5:00000000
r4:c782c000
[<c0051904>] (lock_acquire) from [<c032e484>] (_raw_spin_lock_irqsave+0x60/0x74)
r6:c01a1100 r5:800000d3 r4:c798acd0
[<c032e424>] (_raw_spin_lock_irqsave) from [<c01a1100>] (pl061_irq_type+0x28/0x)
r6:00000000 r5:00000000 r4:c798acd0
[<c01a10d8>] (pl061_irq_type) from [<c0059ef4>] (__irq_set_trigger+0x70/0x104)
r6:00000000 r5:c01a10d8 r4:c046da1c r3:c01a10d8
[<c0059e84>] (__irq_set_trigger) from [<c005b348>] (irq_set_irq_type+0x40/0x60)
r10:c043240c r8:00000060 r7:00000000 r6:c046da1c r5:00000060 r4:00000000
[<c005b308>] (irq_set_irq_type) from [<c01a1208>] (pl061_irq_map+0x40/0x54)
r6:c79693c0 r5:c798acd0 r4:00000060
[<c01a11c8>] (pl061_irq_map) from [<c005d27c>] (irq_domain_associate+0xc0/0x190)
r5:00000060 r4:c046da1c
[<c005d1bc>] (irq_domain_associate) from [<c005d604>] (irq_domain_associate_man)
r8:00000008 r7:00000000 r6:c79693c0 r5:00000060 r4:00000000
[<c005d5d0>] (irq_domain_associate_many) from [<c005d864>] (irq_domain_add_simp)
r8:c046578c r7:c035b72c r6:c79693c0 r5:00000060 r4:00000008 r3:00000008
[<c005d814>] (irq_domain_add_simple) from [<c01a1380>] (pl061_probe+0xc4/0x22c)
r6:00000060 r5:c0464380 r4:c798acd0
[<c01a12bc>] (pl061_probe) from [<c01c0450>] (amba_probe+0x74/0xe0)
r10:c043240c r9:c0455234 r8:00000000 r7:c047d7f8 r6:c047d744 r5:00000000
r4:c0464380
This moves the irqdomain initialization to a point where the spinlock
and GPIO chip are both fully propulated, so the callbacks can be used
without crashes.
I had some problem reproducing the crash, as the devm_kzalloc():ed
zeroed memory would seemingly mask the spinlock as something OK,
but by poisoning the lock like this:
u32 *dum;
dum = (u32 *) &chip->lock;
*dum = 0xaaaaaaaaU;
I could reproduce, fix and test the patch.
Reported-by: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
|
|
This driver can be built as a module now.
Add MODULE_ALIAS to support module auto-loading.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The prototype for static GPIO lookup functions has been updated to use
an explicit type for GPIO lookup flags. Unfortunately the definition of
of_find_gpio() when CONFIG_OF is not defined has been omitted, which
triggers a warning. This patch fixes this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's not obvious from the label name but "err1" tries to release
"p->irq_domain" which leads to a NULL dereference.
Fixes: 119f5e448d32 ('gpio: Renesas R-Car GPIO driver V3')
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a bug in msm_gpio_probe() where we do:
msm_gpio.summary_irq = platform_get_irq(pdev, 0);
if (msm_gpio.summary_irq < 0) {
The problem is that "msm_gpio.summary_irq" is unsigned so the error
handling doesn't work. I've fixed it by making it signed.
Fixes: 43f68444bce7 ('gpio: msm: Add device tree and irqdomain support for gpio-msm-v2')
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a bug in mvebu_gpio_probe() where we do:
mvchip->irqbase = irq_alloc_descs(-1, 0, ngpios, -1);
if (mvchip->irqbase < 0) {
The problem is that mvchip->irqbase is unsigned so the error handling
doesn't work. I have changed it to be a regular int.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO mapping properties were defined using the GPIOF_* flags, which are
declared in linux/gpio.h. This file is not included when using the
GPIO descriptor interface.
This patch declares the flags that can be used as GPIO mappings
properties in linux/gpio/driver.h, and uses them in gpiolib, so that no
deprecated declarations are used by the GPIO descriptor interface.
This patch also allows GPIO_OPEN_DRAIN and GPIO_OPEN_SOURCE to be
specified as GPIO mapping properties.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
find_chip_by_name() was incorrectly implemented by using
gpio_lookup_list instead of gpiod_chips to iterate through all the
registered GPIO controllers. This patch reimplements it by using
gpiochip_find() with a custom search function, which simplifies the code
on top of fixing the mistake.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes a check for offset in gpio_to_irq_unbanked()
and also assigns gpio_irq, gpio_unbanked of chips[0] to
appropriate values which is used in gpio_to_irq_unbanked()
function.
Without this patch, unbanked IRQ handling is broken.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We still have some legacy code needing the callback functions
that won't work properly without platform data. To use platform
data for twl4030-gpio, we need to not trash the possible data.
Cc: linux-gpio@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[tony@atomide.com: folded in fix from Fengguang to use struct assignment]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit c111feabe2e2 (gpio: twl4030: Cache the direction and output
states in private data) improved things in general, but caused a
regression for setting the GPIO output direction.
The change reorganized twl_direction_out() and twl_set() and swapped
the function names around in the process. While doing that, a bug got
introduced that's not obvious while reading the patch as it appears
as no change to the code.
The bug is we now call function twl4030_set_gpio_dataout() twice in
both twl_direction_out() and twl_set(). Instead, we should first
call twl_direction_out() in twl_direction_out() followed by
twl4030_set_gpio_dataout() in twl_set().
This regression probably has gone unnoticed for a long time as the
bootloader may have set the GPIO direction properly in many cases.
This fixes at least the LCD panel not turning on omap3 LDP for
example.
Cc: linux-gpio@vger.kernel.org
Cc: stable@vger.kernel.org #v3.9+
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
|
|
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
|
|
|
|
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
|
|
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
|
|
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
|
|
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
|
|
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree. In this case it's involved:
- Some Davinci driver updates that has required corresponding
platform code changes (gpio mostly)
- CCI bindings and a few driver updates
- Marvell mvebu patches for PCI MSI support (could have gone through
the PCI tree for this release, but they were acked by Bjorn for
3.12 so we kept them through arm-soc).
- Marvell dove switch-over to DT-based PCIe configuration
- Misc updates for Samsung platform dmaengine drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
PCI: mvebu: make local functions static
PCI: mvebu: add I/O access wrappers
PCI: mvebu: Dynamically detect if the PEX link is up to enable hot plug
ARM: mvebu: fix gated clock documentation
ARM: dove: remove legacy pcie and clock init
ARM: dove: switch to DT probed mbus address windows
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
PCI: mvebu: add support for Marvell Dove SoCs
PCI: mvebu: add support for reset on GPIO
PCI: mvebu: remove subsys_initcall
PCI: mvebu: increment nports only for registered ports
PCI: mvebu: move clock enable before register access
PCI: mvebu: add support for MSI
irqchip: armada-370-xp: implement MSI support
...
|
|
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
|
|
|
|
mxs is a devicetree only platform, so there is no need to check whether we
are in dt or platform data case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pl061 driver has no real dependency on ARM, so remove the kconfig
dependency.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR(). Also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
module_platform_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing .owner of struct gpio_chip. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing headers for drivers/gpiolib/devres.c.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Current Kconfig allows GPIO_DEVRES to be selected and compiled without
GPIOLIB. This does not make sense anymore since GPIOLIB has become the
exclusive way to deal with GPIOs. This patch makes GPIO_DEVRES available
only if GPIOLIB is selected.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SA1100 was implementing its own variants of gpio_get_value()
and gpio_set_value() and only selectively falling back to
gpiolib for extended (EGPIO) handling. However the driver in
gpio/gpio-sa1100.c already handles the same functionality for
these lines, yet remain unused.
The only upside would be things like a timing-critical hotpath
on bit-banged GPIO, but that kind of things does not seem to
happen on these GPIOs, so it is not worth having the extra
complexity.
Tested with some buttons on the Compaq iPAQ H3630.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Kukjin Kim:
Samsung Cleanup for v3.13
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
s3c-camif: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
gpio: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
ARM: S3C64XX: Move if ARCH_S3C64XX statement into mach-s3c64xx
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the return value if devm_gpiod_get_index(). It was returning 0 while
it should return the obtained GPIO descriptor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ACPI GpioInt resources contain polarity field that is used to specify
whether the interrupt is active high or low. Since gpiolib supports
GPIOF_ACTIVE_LOW we can pass this information in the flags field in
acpi_find_gpio(), analogous to the DeviceTree version.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpiod_get_index() and gpiod_get() are now the new preferred way to request
GPIOs. Add support for finding the corresponding GPIO descriptor from ACPI
namespace.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Linus Torvalds
Valentine Barshak
Stephen Boyd
Roger Quadros
Kevin Hilman
Olof Johansson
Heikki Krogerus
Liu Gang
Alexandre Courbot
Markus Mayer
Linus Walleij
Axel Lin
Michal Nazarewicz
Dan Carpenter
Lad, Prabhakar
Tony Lindgren
Rafael J. Wysocki
Russell King
Rob Herring
Fabio Estevam
Wei Yongjun
Christian Ruppert
Mika Westerberg