| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Backmerge to sync the DP MST atomic changes to drm-intel-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Move display hdcp related members under drm_i915_private display
sub-struct.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1083f5a58cce1507bd19bf7f98bf85e9351b741e.1661779055.git.jani.nikula@intel.com
|
|
If it's modified runtime, it's runtime info.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Maarten Lankhort <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b146250e02a4b2f086e7e587dd1742589e0e8fba.1660910433.git.jani.nikula@intel.com
|
|
Now that we've finally gotten rid of the non-atomic MST users leftover in
the kernel, we can finally get rid of all of the legacy payload code we
have and move as much as possible into the MST atomic state structs. The
main purpose of this is to make the MST code a lot less confusing to work
on, as there's a lot of duplicated logic that doesn't really need to be
here. As well, this should make introducing features like fallback link
retraining and DSC support far easier.
Since the old payload code was pretty gnarly and there's a Lot of changes
here, I expect this might be a bit difficult to review. So to make things
as easy as possible for reviewers, I'll sum up how both the old and new
code worked here (it took me a while to figure this out too!).
The old MST code basically worked by maintaining two different payload
tables - proposed_vcpis, and payloads. proposed_vcpis would hold the
modified payload we wanted to push to the topology, while payloads held the
payload table that was currently programmed in hardware. Modifications to
proposed_vcpis would be handled through drm_dp_allocate_vcpi(),
drm_dp_mst_deallocate_vcpi(), and drm_dp_mst_reset_vcpi_slots(). Then, they
would be pushed via drm_dp_mst_update_payload_step1() and
drm_dp_mst_update_payload_step2().
Furthermore, it's important to note how adding and removing VC payloads
actually worked with drm_dp_mst_update_payload_step1(). When a VC payload
is removed from the VC table, all VC payloads which come after the removed
VC payload's slots must have their time slots shifted towards the start of
the table. The old code handles this by looping through the entire payload
table and recomputing the start slot for every payload in the topology from
scratch. While very much overkill, this ends up doing the right thing
because we always order the VCPIs for payloads from first to last starting
timeslot.
It's important to also note that drm_dp_mst_update_payload_step2() isn't
actually limited to updating a single payload - the driver can use it to
queue up multiple payload changes so that as many of them can be sent as
possible before waiting for the ACT. This is -technically- not against
spec, but as Wayne Lin has pointed out it's not consistently implemented
correctly in hubs - so it might as well be.
drm_dp_mst_update_payload_step2() is pretty self explanatory and basically
the same between the old and new code, save for the fact we don't have a
second step for deleting payloads anymore -and thus rename it to
drm_dp_mst_add_payload_step2().
The new payload code stores all of the current payload info within the MST
atomic state and computes as much of the state as possible ahead of time.
This has the one exception of the starting timeslots for payloads, which
can't be determined at atomic check time since the starting time slots will
vary depending on what order CRTCs are enabled in the atomic state - which
varies from driver to driver. These are still stored in the atomic MST
state, but are only copied from the old MST state during atomic commit
time. Likewise, this is when new start slots are determined.
Adding/removing payloads now works much more closely to how things are
described in the spec. When we delete a payload, we loop through the
current list of payloads and update the start slots for any payloads whose
time slots came after the payload we just deleted. Determining the starting
time slots for new payloads being added is done by simply keeping track of
where the end of the VC table is in
drm_dp_mst_topology_mgr->next_start_slot. Additionally, it's worth noting
that we no longer have a single update_payload() function. Instead, we now
have drm_dp_mst_add_payload_step1|2() and drm_dp_mst_remove_payload(). As
such, it's now left it up to the driver to figure out when to add or remove
payloads. The driver already knows when it's disabling/enabling CRTCs, so
it also already knows when payloads should be added or removed.
Changes since v1:
* Refactor around all of the completely dead code changes that are
happening in amdgpu for some reason when they really shouldn't even be
there in the first place… :\
* Remove mention of sending one ACT per series of payload updates. As Wayne
Lin pointed out, there are apparently hubs on the market that don't work
correctly with this scheme and require a separate ACT per payload update.
* Fix accidental drop of mst_mgr.lock - Wayne Lin
* Remove mentions of allowing multiple ACT updates per payload change,
mention that this is a result of vendors not consistently supporting this
part of the spec and requiring a unique ACT for each payload change.
* Get rid of reference to drm_dp_mst_port in DC - turns out I just got
myself confused by DC and we don't actually need this.
Changes since v2:
* Get rid of fix for not sending payload deallocations if ddps=0 and just
go back to wayne's fix
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-18-lyude@redhat.com
|
|
Reduce the bloat of i915_reg.h. The registers are also only needed in a
few places, no need to have them defined everywhere.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ce8334342e8bdf92c17c714aa13574e66cad93bb.1659607033.git.jani.nikula@intel.com
|
|
- General driver clean-up (Jani, Ville, Julia)
- DG2 enabling (Anusha, Vandita)
- Fix sparse warnings (Imre, Jani)
- DMC MMIO range checks (Anusha)
- Audio related fixes (Jani)
- Runtime PM fixes (Anshuman)
- PSR fixes (Jouni, Jose)
- Media freq factor and per-gt enhancements (Ashutosh, Dale)
- DSI fixes for ICL+ (Jani)
- Disable DMC flip queue handlers (Imre)
- ADL_P voltage swing updates (Balasubramani)
- Use more the VBT for panel information (Ville, Animesh)
- Fix on Type-C ports with TBT mode (Vivek)
- Improve fastset and allow seamless M/N changes (Ville)
- Accept more fixed modes with VRR/DMRRS panels (Ville)
- FBC fix (Jose)
- Remove noise logs (Luca)
- Disable connector polling for a headless SKU (Jouni)
- Sanitize display underrun reporting (Ville)
- ADL-S display PLL w/a (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YrNzP2WTf3WBvpvd@intel.com
|
|
Each gt contains an independent instance of pcode. Extend pcode functions
to interface with pcode on different gt's. To avoid creating dependency of
display functionality on intel_gt, pcode function interfaces are exposed in
terms of uncore rather than intel_gt. Callers have been converted to pass
in the appropritate (i915 or intel_gt) uncore to the pcode functions.
v2: Expose pcode functions in terms of uncore rather than gt (Jani/Rodrigo)
v3: Retain previous function names to eliminate needless #defines (Rodrigo)
v4: Move out i915_pcode_init() to a separate patch (Tvrtko)
Remove duplicated drm_err/drm_dbg from intel_pcode_init() (Tvrtko)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519085732.1276255-2-tvrtko.ursulin@linux.intel.com
[tursulin: fixup merge conflict]
|
|
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
|
|
Move intel_display_power_well_is_enabled() to intel_power_well.c, as a step
towards making the low-level power well internals (i915_power_well_ops/desc
structs) hidden.
Eventually the call to this function and in general accessing power
wells directly from elsewhere in the driver should be replaced by the
use of power domains.
No functional change.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222165137.1004194-9-imre.deak@intel.com
|
|
Prefer acronym-based naming to be in line with the rest of the driver.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220112111740.1208374-1-jani.nikula@intel.com
|
|
The snb+ pcode mailbox code is not sideband, so split it out to a
separate file. As can be seen from the #include changes, very few places
use both sideband and pcode.
Code movement only.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/185deb18eb739e5ae019e27834b9997dcc1347bc.1634207064.git.jani.nikula@intel.com
|
|
On some MST docking stations, rx_info can only be read after
RepeaterAuth_Send_ReceiverID_List and the RxStatus READY bit is set
otherwise the read will return -EIO.
This behavior causes the mst stream type1 capability test to fail to
read rx_info and determine if the topology supports type1 and fallback
to type0.
To fix this, check for type1 capability when we receive rx_info within
the AKE flow when we read RepeaterAuth_Send_ReceiverID_List instead
of an explicit read just for type1 capability checking.
This does require moving where we set stream_types to after
hdcp2_authenticate_sink() when we get rx_info but this occurs before we
do hdcp2_propagate_stream_management_info.
Also, legacy HDCP 2.0/2.1 are not type 1 capable either so check for
that as well.
Changes since v5:
- rename intel_set_stream_types() to intel_hdcp_prepare_streams()
(Anshuman)
Changes since v4:
- move topology_type1_capable to intel_digital_port and rename it as
hdcp_mst_type1_capable (Anshuman)
- make a helper function intel_set_stream_types() to set stream types
in hdcp2_authenticate_and_encrypt() (Anshuman)
- break on failure to set stream types and retry instead of returning
- remove no longer used declaration for streams_type1_capable()
Changes since v2:
- Remove no longer used variables in _intel_hdcp2_enable()
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-4-juston.li@intel.com
|
|
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
|
|
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
|
|
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.
v2:
- Restore a lost negation in intel_pll_is_valid().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743d5da73058b0a2271e9c127a84fb494)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
GLK has always been a bit of a special case since it reports INTEL_GEN()
as 9, but has version 10 display IP. Now we can properly represent the
display version as 10 and simplify the display generation tests
throughout the display code.
Aside from manually adding the version to the glk_info structure, the
rest of this patch is generated with a Coccinelle semantic patch. Note
that we also need to switch any code that matches gen10 today but *not*
GLK to be CNL-specific:
@@ expression dev_priv; @@
- DISPLAY_VER(dev_priv) > 9
+ DISPLAY_VER(dev_priv) >= 10
@@ expression dev_priv, E; @@
(
- DISPLAY_VER(dev_priv) >= 10 && E
+ (DISPLAY_VER(dev_priv) >= 11 || IS_CANNONLAKE(dev_priv)) && E
|
- DISPLAY_VER(dev_priv) >= 10
+ DISPLAY_VER(dev_priv) >= 11 || IS_CANNONLAKE(dev_priv)
|
- IS_DISPLAY_RANGE(dev_priv, 10, E)
+ IS_DISPLAY_RANGE(dev_priv, 11, E) || IS_CANNONLAKE(dev_priv)
)
@@ expression dev_priv, E, E2; @@
(
- (IS_CANNONLAKE(dev_priv) || IS_GEMINILAKE(dev_priv))
+ IS_DISPLAY_VER(dev_priv, 10)
|
- E || IS_CANNONLAKE(dev_priv) || IS_GEMINILAKE(dev_priv)
+ E || IS_DISPLAY_VER(dev_priv, 10)
|
- (IS_GEMINILAKE(dev_priv) || IS_CANNONLAKE(dev_priv))
+ IS_DISPLAY_VER(dev_priv, 10)
|
- IS_GEMINILAKE(dev_priv) || E || IS_CANNONLAKE(dev_priv)
+ E || IS_DISPLAY_VER(dev_priv, 10)
|
- E || IS_GEMINILAKE(dev_priv) || E2 || IS_CANNONLAKE(dev_priv)
+ E || E2 || IS_DISPLAY_VER(dev_priv, 10)
|
- (IS_DISPLAY_VER(dev_priv, 10) || IS_GEMINILAKE(dev_priv))
+ IS_DISPLAY_VER(dev_priv, 10)
|
- (IS_GEMINILAKE(dev_priv) || IS_DISPLAY_VER(dev_priv, 10))
+ IS_DISPLAY_VER(dev_priv, 10)
)
@@ expression dev_priv; @@
- (IS_DISPLAY_VER(dev_priv, 9) && !IS_GEMINILAKE(dev_priv))
+ IS_DISPLAY_VER(dev_priv, 9)
@@ expression dev_priv; @@
(
- !(DISPLAY_VER(dev_priv) >= 11 || IS_DISPLAY_VER(dev_priv, 10))
+ DISPLAY_VER(dev_priv) < 10
|
- (DISPLAY_VER(dev_priv) >= 11 || IS_DISPLAY_VER(dev_priv, 10))
+ DISPLAY_VER(dev_priv) >= 10
)
@@ expression dev_priv, E; @@
- E || DISPLAY_VER(dev_priv) >= 11 || IS_DISPLAY_VER(dev_priv, 10)
+ E || DISPLAY_VER(dev_priv) >= 10
@@ expression dev_priv, E; @@
- (IS_DISPLAY_RANGE(dev_priv, 11, E) || IS_DISPLAY_VER(dev_priv, 10))
+ IS_DISPLAY_RANGE(dev_priv, 10, E)
@@ expression dev_priv; @@
(
- DISPLAY_VER(dev_priv) >= 11 || IS_CANNONLAKE(dev_priv) || IS_GEN9_LP(dev_priv)
+ DISPLAY_VER(dev_priv) >= 10 || IS_GEN9_LP(dev_priv)
|
- IS_GEN9_LP(dev_priv) || DISPLAY_VER(dev_priv) >= 11 || IS_CANNONLAKE(dev_priv)
+ IS_GEN9_LP(dev_priv) || DISPLAY_VER(dev_priv) >= 10
)
@@ expression dev_priv, E; @@
- !(DISPLAY_VER(dev_priv) >= E)
+ DISPLAY_VER(dev_priv) < E
v2:
- Convert gen10 conditions that don't include GLK into CNL conditions.
(Ville)
v3:
- Rework coccinelle rules so that "ver>=10" turns into "ver>=11||is_cnl." (Ville)
v3.1:
- Manually re-add the ".display.version = 10" to glk_info after
regenerating patch via Coccinelle.
v4:
- Also apply cocci rules to intel_pm.c and i915_irq.c! (CI)
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210322233840.4056851-1-matthew.d.roper@intel.com
|
|
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
|
|
hdcp2_enable_stream_encryption shouldn't get called in case
of any port authentication or encryption error, though
hdcp2_enable_stream_encryption checks for link encryption
before enabling stream encryption and returns error but
this return error code won't be correct in case of any error
due to port authentication and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-4-anshuman.gupta@intel.com
|
|
When stream encryption enabling fails due to Link encryption status
has stopped, prepare HDCP2 for recovery by disabling port authentication
and encryption such that it can re-attempt port authentication
and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-3-anshuman.gupta@intel.com
|
|
DP MST Link Check performed only for the connector involved with
HDCP port authentication and encryption, for other connector it
simply returns link check with true and update the uevent.
Therefore in case of HDCP 2.2 link failure, disable HDCP encryption
and de-authenticate the port so next time it can enable port
authentication and encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319100208.5886-2-anshuman.gupta@intel.com
|
|
It requires to check streams type1 capability in mst topology
by checking Rxinfo instead connector HDCP2.x capability in
order to enforce type0 stream encryption in a mix of
HDCP {1.x,2.x} mst topology.
Rxcaps always shows HDCP 2.x capability of immediate downstream
connector. Let's use Rxinfo HDCP1_DEVICE_DOWNSTREAM bit to
detect a HDCP {1.x,2.x} mix mst topology.
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210319091732.17547-1-anshuman.gupta@intel.com
|
|
Move (num_hdcp_streams > 0) condition to stream_encryption()
code block, where it actually belongs.
This fixes the static analysis error of uninitialized symbol 'ret'.
v2:
- return 0 as the return value is already checked. [Ankit]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210120103032.15198-1-anshuman.gupta@intel.com
|
|
Initialize no. of streams transmitted on a port to zero
such that intel_hdcp_required_content_stream() can
prepared the content stream after subsequemt attmept to
enable hdcp after a HDCP failure.
v2:
- Initialize k at top level instead of else branch. [Jani]
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210119064655.1605-2-anshuman.gupta@intel.com
|
|
Enable HDCP 2.2 MST support till Gen12.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-20-anshuman.gupta@intel.com
|
|
Authenticate and enable port encryption only once for
an active HDCP 2.2 session, once port is authenticated
and encrypted enable encryption for each stream that
requires encryption on this port.
Similarly disable the stream encryption for each encrypted
stream, once all encrypted stream encryption is disabled,
disable the port HDCP encryption and deauthenticate the port.
v2:
- Add connector details in drm_err. [Ram]
- 's/port_auth/hdcp_auth_status'. [Ram]
- Added a debug print for stream enc.
v3:
- uniformity for connector detail in DMESG. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-19-anshuman.gupta@intel.com
|
|
This requires for HDCP 2.2 MST check link.
As for DP/HDMI shims check_2_2_link retrieves the connector
from dig_port, this is not sufficient or DP MST connector,
there can be multiple DP MST topology connector associated
with same dig_port.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-16-anshuman.gupta@intel.com
|
|
Add support for multiple mst stream in hdcp port data
which will be used by RepeaterAuthStreamManage msg and
HDCP 2.2 security f/w for m' validation.
Security f/w doesn't have any provision to mark the stream_type
for each stream separately, it just take single input of
stream_type while authenticating the port and applies the
same stream_type to all streams. So driver mark each stream_type
with common highest supported content type for all streams
in DP MST Topology.
Security f/w supports RepeaterAuthStreamManage msg and m'
validation only once during port authentication and encryption.
Though it is not compulsory, security fw should support dynamic
update of content_type and should support RepeaterAuthStreamManage
msg and m' validation whenever required.
v2:
- Init the hdcp port data k for HDMI/DP SST stream.
v3:
- Cosmetic changes. [Uma]
v4:
- 's/port_auth/hdcp_port_auth'. [Ram]
- Commit log improvement.
v5:
- Comment and commit log improvement. [Ram]
v6:
- Check first connector connected status before intel_encoder_is_mst
to avoid any NULL pointer dereference.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Juston Li <juston.li@intel.com>
Acked-by: Juston Li <juston.li@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-15-anshuman.gupta@intel.com
|
|
hdcp_port_data is specific to a port on which HDCP
encryption is getting enabled, so encapsulate it to
intel_digital_port.
This will be required to enable HDCP 2.2 stream encryption.
v2:
- 's/port_data/hdcp_port_data'. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-12-anshuman.gupta@intel.com
|
|
Pass dig_port as an argument to intel_hdcp_init()
and intel_hdcp2_init().
This will be required for HDCP 2.2 stream encryption.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-11-anshuman.gupta@intel.com
|
|
Enable HDCP 1.4 DP MST stream encryption.
Enable stream encryption once encryption is enabled on
the DP transport driving the link for each stream which
has requested encryption.
Disable stream encryption for each stream that no longer
requires encryption before disabling HDCP encryption on
the link.
v2:
- Added debug print for stream encryption.
- Disable the hdcp on port after disabling last stream
encryption.
v3:
- Cosmetic change, removed the value less comment. [Uma]
v4:
- Split the Gen12 HDCP enablement patch. [Ram]
- Add connector details in drm_err.
v5:
- uniformity for connector detail in DMESG. [Ram]
- comments improvement. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-9-anshuman.gupta@intel.com
|
|
DP MST stream encryption status requires time of a link frame
in order to change its status, but as there were some HDCP
encryption timeout observed earlier, it is safer to use
ENCRYPT_STATUS_CHANGE_TIMEOUT_MS timeout for stream status too,
it requires to move the macro to a header.
It will be used by both HDCP{1.x,2.x} stream status timeout.
Related: 'commit 7e90e8d0c0ea ("drm/i915: Increase timeout for Encrypt
status change")'
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-7-anshuman.gupta@intel.com
|
|
Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.
This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.
This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com
|
|
There can be situation when DP MST connector is created without
mst modeset being done, in those cases connector->encoder will be
NULL. MST connector->encoder initializes after modeset.
Don't enable HDCP in such cases to prevent any crash.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Juston Li <juston.li@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-5-anshuman.gupta@intel.com
|
|
Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.
Fixes: a6597faa2d59 ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com
|
|
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes: 33f9a623bfc6 ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
|
|
When roll over detected for seq_num_m, we shouldn't continue with stream
management with rolled over value.
So we are terminating the stream management retry, on roll over of the
seq_num_m.
v2:
using drm_dbg_kms instead of DRM_DEBUG_KMS [Anshuman]
v3:
dev_priv is used as i915 [JaniN]
v4:
roll over is detected at the start of the stream management.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> [v3]
Tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923132435.17039-3-anshuman.gupta@intel.com
|
|
As per the HDCP2.2 compliance test 1B-10 expectation, when stream
management for a repeater fails, we retry thrice and when it fails
in all retries, HDCP2.2 reauthentication aborted at kernel.
v2:
seq_num_m++ is extended for steam management failures too.[Anshuman]
v3:
use drm_dbg_kms instead of DRM_DEBUG_KMS [Anshuman]
v4:
dev_priv is used as i915 [JaniN]
v5:
Few improvisements are done [Sean]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923132435.17039-2-anshuman.gupta@intel.com
|
|
Now that all the groundwork has been laid, we can turn on HDCP 1.4 over
MST. Everything except for toggling the HDCP signalling and HDCP 2.2
support is the same as the DP case, so we'll re-use those callbacks
Cc: Juston Li <juston.li@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-12-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-13-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-13-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-15-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-17-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-17-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-18-sean@poorly.run #v7
Changes in v2:
-Toggle HDCP from encoder disable/enable
-Don't disable HDCP on MST connector destroy, leave that for encoder
disable, just ensure the check_work routine isn't running any longer
Changes in v3:
-Place the shim in the new intel_dp_hdcp.c file (Ville)
Changes in v4:
-Actually use the mst shim for mst connections (Juston)
-Use QUERY_STREAM_ENC_STATUS MST message to verify channel is encrypted
Changes in v5:
-Add sleep on disable signalling to match hdmi delay
Changes in v6:
-Disable HDCP over MST on GEN12+ since I'm unsure how it should work and I
don't have hardware to test it
Changes in v7:
-Remove hdcp2 shims for MST in favor of skipping hdcp2 init (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-18-sean@poorly.run
|
|
Currently we derive the connector from digital port in check_link(). For
MST, this isn't sufficient since the digital port passed into the
function can have multiple connectors downstream. This patch adds
connector to the check_link() arguments so we have it when we need it.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-13-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-14-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-14-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-15-sean@poorly.run #v7
Changes in v4:
-Added to the set
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-15-sean@poorly.run
|
|
This patch plumbs port through hdcp init instead of relying on
intel_attached_encoder() to return a non-NULL encoder which won't work
for MST connectors.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-13-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-13-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-14-sean@poorly.run #v7
Changes in v5:
-Added to the set
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-14-sean@poorly.run
|
|
This patch is required for HDCP over MST. If a port is being used for
multiple HDCP streams, we don't want to fully disable HDCP on a port if
one of them is disabled. Instead, we just disable the HDCP signalling on
that particular pipe and exit early. The last pipe to disable HDCP will
also bring down HDCP on the port.
In order to achieve this, we need to keep a refcount in intel_digital_port
and protect it using a new hdcp_mutex.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-8-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-9-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-9-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-9-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-9-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-10-sean@poorly.run #v7
Changes in v2:
-Move the toggle_signalling call into _intel_hdcp_disable so it's called from check_work
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-Split minor intel_hdcp_disable refactor into separate patch (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-10-sean@poorly.run
|
|
Add an out label and un-indent hdcp disable in preparation for
hdcp_mutex. No functional changes
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-9-sean@poorly.run #v7
Changes in v7:
-Split into separate patch (Ramalingam)
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-9-sean@poorly.run
|
|
This patch adds some protection against connectors being destroyed
before the HDCP workers are finished.
For check_work, we do a synchronous cancel after the connector is
unregistered which will ensure that it is finished before destruction.
In the case of prop_work, we can't do a synchronous wait since it needs
to take connection_mutex which could cause deadlock. Instead, we'll take
a reference on the connector when scheduling prop_work and give it up
once we're done.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-8-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-8-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-8-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-8-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-8-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-8-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-Change the WARN_ON condition in intel_hdcp_cleanup to allow for
initializing connectors as well
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-8-sean@poorly.run
|
|
This is a bit of housecleaning for a future patch. Instead of sprinkling
hdcp->value assignments and prop_work scheduling everywhere, introduce a
function to do it for us.
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-7-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-7-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-7-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-7-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-7-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-7-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-7-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-Rebased on top of drm_* logging changes
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-7-sean@poorly.run
|
|
Instead of using intel_dig_port's encoder pipe to determine which
transcoder to toggle signalling on, use the cpu_transcoder field already
stored in intel_hdmi.
This is particularly important for MST.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-6-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-6-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-6-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-6-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-6-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-6-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-s/hdcp/hdmi/ in commit msg (Ram)
Changes in v4:
-Rebased on intel_de_(read|write) change
Changes in v5:
-Update hdcp->cpu_transcoder in intel_hdcp_enable so it works with pipe != 0
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-6-sean@poorly.run
|
|
On HDCP disable, clear the repeater bit. This ensures if we connect a
non-repeater sink after a repeater, the bit is in the state we expect.
Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.17+
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-3-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-3-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-3-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-3-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-3-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-3-sean@poorly.run #v7
Changes in v2:
-Added to the set
Changes in v3:
-None
I had previously agreed that clearing the rep_ctl bits on enable would
also be a good idea. However when I committed that idea to code, it
didn't look right. So let's rely on enables and disables being paired
and everything outside of that will be considered a bug
Changes in v4:
-s/I915_(READ|WRITE)/intel_de_(read|write)/
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-3-sean@poorly.run
|
|
This patch fixes a few bugs:
1- We weren't taking into account sha_leftovers when adding multiple
ksvs to sha_text. As such, we were or'ing the end of ksv[j - 1] with
the beginning of ksv[j]
2- In the sha_leftovers == 2 and sha_leftovers == 3 case, bstatus was
being placed on the wrong half of sha_text, overlapping the leftover
ksv value
3- In the sha_leftovers == 2 case, we need to manually terminate the
byte stream with 0x80 since the hardware doesn't have enough room to
add it after writing M0
The upside is that all of the HDCP supported HDMI repeaters I could
find on Amazon just strip HDCP anyways, so it turns out to be _really_
hard to hit any of these cases without an MST hub, which is not (yet)
supported. Oh, and the sha_leftovers == 1 case works perfectly!
Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.17+
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-2-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-2-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-2-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-2-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-2-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-2-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-2-sean@poorly.run #v7
Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-Rebased on intel_de_write changes
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-2-sean@poorly.run
|
|
HDCP code doesn't require to access power_well internal stuff,
instead it should use the intel_display_power_well_is_enabled()
to get the status of desired power_well.
No functional change.
v2:
- used with_intel_runtime_pm instead of get/put. [Jani]
v3:
- rebased.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805114521.867-3-anshuman.gupta@intel.com
|
|
Currently intel_hdcp_update_pipe() is also getting called for non-hdcp
connectors and get through its conditional code flow, which is completely
unnecessary for non-hdcp connectors, therefore it make sense to
have an early return. No functional change.
v2:
- rebased.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805114521.867-2-anshuman.gupta@intel.com
|
|
drm_hdcp_check_ksvs_revoked() returns the number of revoked keys and
error codes when the SRM parsing is failed.
Errors in SRM parsing can't affect the HDCP auth, hence with this patch,
I915 will look out for revoked key count alone.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429134555.22106-1-ramalingam.c@intel.com
|
Jani Nikula
Lyude Paul
Dave Airlie
Ashutosh Dixit
Thomas Zimmermann
Imre Deak
Juston Li
Ville Syrjälä
Lucas De Marchi
Matt Roper
Anshuman Gupta
Ramalingam C
Sean Paul