| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With 'commit 30886c5a ("drm/i915: VLV/CHV PSR: Increase wait delay
time before active PSR.")' we fixed a blank screen when first
activation was happening immediately after PSR being enabled.
There we gave more time for idleness by increasing the delay
between re-activating sequences.
However, commit "drm/i915: Delay first PSR activation."
delay the first activation in a better way keeping a good PSR
residency. So, we can now reduce the delay on re-enable.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When debuging the frozen screen caused by HW tracking with low
power state I noticed that if we keep moving the mouse non stop
you will miss the screen updates for a while. At least
until we stop moving the mouse for a small time and move again.
The actual enabling should happen immediately after
Display Port enabling sequence finished with links trained and
everything enabled. However we face many issues when enabling PSR
right after a modeset.
On VLV/CHV we face blank screens on this scenario and on HSW+
we face a recoverable frozen screen, at least until next
exit-activate sequence.
Another workaround for the same issue here would be to increase
re-enable idle time from 100 to 500 as we did for VLV/CHV.
However this patch workaround this issue in a better
way since it doesn't reduce PSR residency and also
allow us to reduce the delay time between re-enables at least
on VLV/CHV.
This is also important to make the sysfs toggle working properly.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
|
|
v2: Split up the ctl vs. data reg handling like in the normal AUX code
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-8-git-send-email-ville.syrjala@linux.intel.com
|
|
Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.
TODO: could probably move a bunch of this kind of stuff into the device
info instead...
v2: Drop the spurious whitespace change (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com
|
|
v2: Keep some MISSING_CASE() stuff (Jani)
s/-1/-PIPE_B/ in the register macro
Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com
|
|
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since active function on VLV immediately activate PSR let's give more
time for idleness. Different from core platforms where we have idle_frames
count.
Also kms_psr_sink_crc now is automated and always get this:
[drm:intel_enable_pipe] enabling pipe A
[drm:intel_edp_backlight_on]
[drm:intel_panel_enable_backlight] pipe
[drm:intel_panel_enable_backlight] pipe A
[drm:intel_panel_actually_set_backlight] set backlight PWM = 7812
PSR gets enabled somewhere here after backlight.
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x0
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
PSR gets flushed around here by intel_atomic_commit
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
[drm:intel_set_memory_cxsr] memory self-refresh is enabled
[drm:intel_connector_check_state] [CONNECTOR:39:eDP-1]
[drm:check_encoder_state] [ENCODER:30:DAC-30]
[drm:check_encoder_state] [ENCODER:31:TMDS-31]
[drm:check_encoder_state] [ENCODER:36:TMDS-36]
[drm:check_encoder_state] [ENCODER:38:TMDS-38]
[drm:check_crtc_state] [CRTC:21]
[drm:check_crtc_state] [CRTC:26]
[drm:intel_psr_activate [i915]] *ERROR* PSR Active
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x
[drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* pipe A underrun
[drm:intel_cpu_fifo_underrun_irq_handler [i915]] *ERROR* CPU pipe A FIFO
Underrun.
It is true that in a product we won't keep disabling and enabling planes so
frequently, but for safeness let's stay conservative.
It is also true that 500ms is an etternity. But PSR is anyway a power saving
feature for idle scenario. So if it is idle feature stays on and 500ms to get
it reanabled is not that insane.
v2: Rebase over intel_psr.c and fix typo.
v3: Revival: Manual tests indicated that this is needed. With a short delay
there is a huge risk of getting blank screens when planes are being enabled.
v4: Revival 2 with reasonable delay. 1/2 sec instead of 5. VBT is 10 sec but
actually time for link training what we aren't doing, but with only 100 sec
in some cases kms_psr_sink_crc manual was showing blank screen,
so let's use this for now. Also changed comment by a FIXME.
v5: Rebase after a long time, remove FIXME and update comment above.
v6: msecs_to_jiffies is already on delay. remove duplication.
v7: use msecs_to_jiffies on schedule_delayed_work call.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com> (v4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-By: Intel Graphics QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Idle frames the number of identical frames needed
before panel can enter PSR.
There are some panels that requires up to minimum of 4 idle
frames available on the market. For these cases usually
VBT should be used to configure the number of idle frames,
but unfortunately this isn't always true and VBT isn't being
set at all.
Let's trust VBT when it is set + 1 and use minimum of 4 + 1
when VBT isn't set. "+1" covers the "of-by-one" case.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
By Spec we should only mask memup and hotplug detection
for hardware tracking cases. However we always masked
LPSP because with power well always enabled on audio
PSR was never being activated and residency was always
zeroed.
Apparently audio driver is tying power well management
and runtime PM for some reason. But with audio runtime
PM working or with audio completely out of picture
we should remove this mask, otherwise we have a high
risk of miss screen updates as faced by Matthew.
WARNING: With this patch if snd_intel_hda driver is
running and not releasing power well properly PSR will
constant Exit and Performance Counter will be 0.
But the best thing of this patch is that with one more
HW tracking working the risks of missed blank screen
are minimized at most.
This affects just core platforms where PSR exit are also
helped by HW tracking: Haswell, Broadwell and Skylake
for now.
v2: Fix commit message explanation. It has nothing to do
with runtime PM on i915 as previously advertised.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since flush actually means invalidate + flush we need to force psr
exit on PSR flush.
On Core platforms there is no way to disable hw tracking and
do the pure sw tracking so we simulate it by fully disable psr and
reschedule a enable back.
So a good idea is to minimize sequential disable/enable in cases we
know that HW tracking like when flush has been originated by a flip.
Also flip had just invalidated it already.
It also uses origin to minimize the a bit the amount of
disable/enabled, mainly when flip already had invalidated.
With this patch in place it is possible to do a flush on dirty areas
properly in a following patch.
v2: Remove duplicated exit on HSW+Sprites as pointed out by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The frontbuffer code gives us accurate information about activity,
let's use it. Again this should avoid unecessary updates when multiple
screens are on.
Also realign function paramaters, I couldn't resist that bit of OCD.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
The current code tracks business across all pipes, but we're only
really interested in the one pipe DRRS is enabled on. Fairly tiny
optimization, but something I noticed while reading the code. But it
might matter a bit when e.g. showing a video or something only on the
external screen, while the panel is kept static.
Also regroup the code slightly: First compute new bitmasks, then take
appropriate actions.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
According to spec: "In PSR HW or SW mode, SW set this bit before writing
registers for a flip. It will be self-clear when it gets to the PSR
active state."
Some versions of spec mention that this is needed when in
"Persistent mode" but define it as same as "SW mode". Since this
fix the page flip case let's assume this is exactly what we need.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On Haswell and Broadwell with link in standby when exit event happens
between vblank and VSC packet, PSR exit on panel but DPA transmitter
still sends black pixel. When this condition hits, panel will intermittently
display black frame.
The known W/A for this case involve the of single_frame update
that isn't supported on Haswell and to be supported on Broadwell
3 other workarounds would be required. So it is better and safe to
just deprecate link_standby for now.
Also, link fully off saves more power than link_standby and afwk
no OEM is requesting link standby on VBT. There is no reason for that.
For Skylake let's just consider it behaves like Broadwell until
we prove otherwise.
v2: Fix commit message (Durga).
v3: Fix conflict with PSR2.
Reference: HSD: bdwgfx/1912559
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Since the beginning there is a missunderstanding on the meaning of this
dpcd bit.
This bit shouldn't indicate whether to use link standby or not, but just
be used to configure TP1, TP2 and TP3 times and tell hw aux should be skiped
since HW is the responsible one.
Even with help of frontbuffer tracking, HW is still fully responsible for
PSR exit logic with/without DP training.
DP_PSR_NO_TRAIN_ON_EXIT means the source doesn't need to do the training, but
it doesn't tell to avoid TP patterns, so we will send minimal TP1 and avoid
TP2. It also means that sink itself can take up to 5 idle frames for training.
6 in our case since we might be off by 1. So we also increment idle_frames by 4
here.
v2: Fix and improve commit message (Durga).
v3: Use minimal TP1 time avoiding TP2 and increase idle frame.
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This wrong logic and useless define came from first versions and
came along with all rework. Just now I notice how ugly, wrong and
useless this is.
val is already defined as 0 anyway and logic is completelly wrong
and useless. So let's starting the link_standby fix with this
cleaning.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We make use of HW tracking for Selective update region and enable frame sync on
sink. We use hardware's hardcoded data values for frame sync and GTC.
v2: Add 3200x2000 resolution restriction with PSR2, move psr2_support to i915_psr
struct, add aux_frame_sync to independently control aux frame sync, rename the
TP2 TIME macro for 2500us (Rodrigo, Siva)
v3: Moving the resolution restriction to intel_psr_enable so that we check it
only once(Durga)
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
BSpec recommends to keep the main link state consistent
between the source and the sink. As per that, update
the main link state in sink DPCD register to 'active',
for Valleyview based platforms.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
psr.active is being unset out of the if so this here is useless and
duplicated.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.
v2: introduce EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
And get rid of the duplicate mode structures. This patch was generated
with the following semantic patch:
@@ @@
struct intel_crtc_state {
+struct drm_crtc_state base;
+
...
-struct drm_display_mode requested_mode;
-struct drm_display_mode adjusted_mode;
...
}
@@ struct intel_crtc_state *state; @@
-state->adjusted_mode
+state->base.adjusted_mode
@@ struct intel_crtc_state *state; @@
-state->requested_mode
+state->base.mode
@@ struct intel_crtc_state state; @@
-state.adjusted_mode
+state.base.adjusted_mode
@@ struct intel_crtc_state state; @@
-state.requested_mode
+state.base.mode
@@ struct drm_crtc *crtc; @@
-to_intel_crtc(crtc)->config.adjusted_mode
+to_intel_crtc(crtc)->config.base.adjusted_mode
@@ identifier member; expression E; @@
-PIPE_CONF_CHECK_FLAGS(adjusted_mode.member, E);
+PIPE_CONF_CHECK_FLAGS(base.adjusted_mode.member, E);
@@ identifier member; @@
-PIPE_CONF_CHECK_I(adjusted_mode.member);
+PIPE_CONF_CHECK_I(base.adjusted_mode.member);
@@ identifier member; @@
-PIPE_CONF_CHECK_CLOCK_FUZZY(adjusted_mode.member);
+PIPE_CONF_CHECK_CLOCK_FUZZY(base.adjusted_mode.member);
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
No functional changes on this patch. Just grouping the link_standy decision
to avoid miss any change. Also making this info available everywhere
which will help to decide when to use vbt's tp time on following patch.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
[danvet: Slight editing of the commit message which was one huge
run-on sentence.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Let's respect vbt full_link (link_standby) on source side as well.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We have only two possible states with so many names and combinations that
might be confusing.
1 - Main link active / enabled / stand by / on
2 - Main link disabled / off / full off
Let's start organizing it by fixing a inverted logic when setting the sink bit.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These conditions applies only to Haswell and we were also checking for them
on Valleyview/Cherryview.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ON these platforms we don't have hardware tracking working for any case.
So we need to fake this on software by forcing psr to exit on every
flush.
Manual tests indicated this was needed.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch introduces exit/activate functions for PSR
on VLV+. Since on VLV+ HW cannot track frame updates and force PSR
exit let's use fully SW tracking available.
v2: Rebase over intel_psr.c;
Remove Single Frame update transitioning from state 3 to 5 directly;
Fake a software invalidation for sprites and cursor so we don't miss
any screen update;
v3: As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Also fix comments as suggested by Durgadoss
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The biggest difference from HSW/BDW PSR here is that VLV enable_source
function enables PSR but let it in Inactive state. So it might be called
on early stage along with setup and enable_sink ones.
v2: Rebase over intel_psr.c;
Remove docs from static functions;
Merge vlv_psr_active_on_pipe;
Timeout for psr transition is 250us;
Remove SRC_TRASMITTER_STATE;
v3: Rebase after is_psr_enabled function got removed;
Get SRC_TRANSMITTER_STATE back to be on the safe side since
default for panels is to require link training on exit when
main link off;
As pointed out by Durgadoss msecs_to_jiffies used on wait_for only uses int,
so let's use 1 instead. Althought the 1/4 of this is needed for the
transition let's use 1 for simplicity;
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This function was in use to check if PSR feature got enabled.
However on HSW and BDW we currently force psr exit by disabling
EDP_PSR_ENABLE bit at EDP_PSR_CTL(dev). So this function was actually
returning the active/inactive state that is different from the enable/disable
meaning and had the risk of false negative.
But anyway this check with DRRS was dangerous, since DRRS could try to get enabled
before PSR gets there. So let's just remove it for now.
A proper synchronization mechanism must be implemented later probably
using pipe config.
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Single frame update is a feature available on BDW for PSR that allows
Source to send Sink only one frame and get it updated. Usually useful
when page flipping. However with our frontbuffer tracking where we force
psr exit on flips we don't need this feature.
Also after it got added here many workaround was added to documentation
to mask some bits when using single frame update. So the safest thing
is to just stop using it.
v2: Rebase after removing skip aux one and fixing typo on commit message.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
OEMs can specify if full_link might be always enabled, i.e. only_standby
over VBT.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Let's use VBT + 1 now we parse it.
v2: fix subject
v3: rebase over intel_psr and without counting on previous fix
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Let's document PSR a bit. No functional changes.
v2: Add actual DocBook entry and accept Daniel's improvements.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
No functional changes. Just cleaning and reorganizing it.
v2: Rebase it puting it to begin of psr rework. This helps to blame easily
at least latest changes.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
Rodrigo Vivi
Ville Syrjälä
Daniel Vetter
Sonika Jindal
Durgadoss R
Ander Conselvan de Oliveira