aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/gpu/drm/vc4 (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-11-07drm/vc4: Fix missing platform_unregister_drivers() call in vc4_drm_register()Yuan Can1-1/+6
A problem about modprobe vc4 failed is triggered with the following log given: [ 420.327987] Error: Driver 'vc4_hvs' is already registered, aborting... [ 420.333904] failed to register platform driver vc4_hvs_driver [vc4]: -16 modprobe: ERROR: could not insert 'vc4': Device or resource busy The reason is that vc4_drm_register() returns platform_driver_register() directly without checking its return value, if platform_driver_register() fails, it returns without unregistering all the vc4 drivers, resulting the vc4 can never be installed later. A simple call graph is shown as below: vc4_drm_register() platform_register_drivers() # all vc4 drivers are registered platform_driver_register() driver_register() bus_add_driver() priv = kzalloc(...) # OOM happened # return without unregister drivers Fixing this problem by checking the return value of platform_driver_register() and do platform_unregister_drivers() if error happened. Fixes: c8b75bca92cb ("drm/vc4: Add KMS support for Raspberry Pi.") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20221103014705.109322-1-yuancan@huawei.com
2022-11-03drm/vc4: hdmi: Fix HSM clock too low on Pi4maxime@cerno.tech2-4/+18
Commit ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at runtime_resume") reintroduced the call to clk_set_min_rate in an attempt to fix the boot without a monitor connected on the RaspberryPi3. However, that introduced a regression breaking the display output entirely (black screen but no vblank timeout) on the Pi4. This is due to the fact that we now have in a typical modeset at boot, in vc4_hdmi_encoder_pre_crtc_configure(), we have a first call to clk_set_min_rate() asking for the minimum rate of the HSM clock for our given resolution, and then a call to pm_runtime_resume_and_get(). We will thus execute vc4_hdmi_runtime_resume() which, since the commit mentioned above, will call clk_set_min_rate() a second time with the absolute minimum rate we want to enforce on the HSM clock. We're thus effectively erasing the minimum mandated by the mode we're trying to set. The fact that only the Pi4 is affected is due to the fact that it uses a different clock driver that tries to minimize the HSM clock at all time. It will thus lower the HSM clock rate to 120MHz on the second clk_set_min_rate() call. The Pi3 doesn't use the same driver and will not change the frequency on the second clk_set_min_rate() call since it's still within the new boundaries and it doesn't have the code to minimize the clock rate as needed. So even though the boundaries are still off, the clock rate is still the right one for our given mode, so everything works. There is a lot of moving parts, so I couldn't find any obvious solution: - Reverting the original is not an option, as that would break the Pi3 again. - We can't move the clk_set_min_rate() call in _pre_crtc_configure() since because, on the Pi3, the HSM clock has the CLK_SET_RATE_GATE flag which prevents the clock rate from being changed after it's been enabled. Our calls to clk_set_min_rate() can change it, so they need to be done before clk_prepare_enable(). - We can't remove the call to clk_prepare_enable() from the runtime_resume hook to put it into _pre_crtc_configure() either, since we need that clock to be enabled to access the registers, and we can't count on the fact that the display will be active in all situations (doing any CEC operation, or listing the modes while inactive are valid for example()). - We can't drop the call to clk_set_min_rate() in _pre_crtc_configure() since we would need to still enforce the minimum rate for a given resolution, and runtime_resume doesn't have access to the current mode, if there's any. - We can't copy the TMDS character rate into vc4_hdmi and reuse it since, because it's part of the KMS atomic state, it needs to be protected by a mutex. Unfortunately, some functions (CEC operations, mostly) can be reentrant (through the CEC framework) and still need a pm_runtime_get. However, we can work around this issue by leveraging the fact that the clk_set_min_rate() calls set boundaries for its given struct clk, and that each different clk_get() call will return a different instance of struct clk. The clock framework will then aggregate the boundaries for each struct clk instances linked to a given clock, plus its hardware boundaries, and will use that. We can thus get an extra HSM clock user for runtime_pm use only, and use our different clock instances depending on the context: runtime_pm will use its own to set the absolute minimum clock setup so that we never lock the CPU waiting for a register access, and the modeset part will set its requirement for the current resolution. And we let the CCF do the coordination. It's not an ideal solution, but it's fairly unintrusive and doesn't really change any part of the logic so it looks like a rather safe fix. Link: https://bugzilla.redhat.com/show_bug.cgi?id=2136234 Fixes: ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at runtime_resume") Reported-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Link: https://lore.kernel.org/r/20221021131339.2203291-1-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-11-03drm/vc4: hdmi: Fix outdated function name in commentmaxime@cerno.tech1-3/+2
A comment introduced by commit 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug") mentions a drm_atomic_helper_connector_hdmi_reset_link() function that was part of the earlier versions but got moved internally and is now named vc4_hdmi_reset_link(). Let's fix the function name. Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug") Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://lore.kernel.org/r/20221024093634.118190-2-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-11-03drm/vc4: hdmi: Take our lock to reset the linkmaxime@cerno.tech1-4/+17
We access some fields protected by our internal mutex in vc4_hdmi_reset_link() (saved_adjusted_mode, output_bpc, output_format) and are calling functions that need to have that lock taken (vc4_hdmi_supports_scrambling()). However, the current code doesn't lock that mutex. Let's make sure it does. Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug") Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://lore.kernel.org/r/20221024093634.118190-1-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-10-20Merge drm/drm-fixes into drm-misc-fixesThomas Zimmermann22-853/+1513
Backmerging to get v6.1-rc1. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
2022-10-13drm/vc4: hdmi: Check the HSM rate at runtime_resumeMaxime Ripard1-0/+20
If our HSM clock has not been properly initialized, any register access will silently lock up the system. Let's check that this can't happen by adding a check for the rate before any register access, and error out otherwise. Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/ Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-2-cd22e962296c@cerno.tech
2022-10-13drm/vc4: hdmi: Enforce the minimum rate at runtime_resumeMaxime Ripard1-0/+9
This is a revert of commit fd5894fa2413 ("drm/vc4: hdmi: Remove clock rate initialization"), with the code slightly moved around. It turns out that we can't downright remove that code from the driver, since the Pi0-3 and Pi4 are in different cases, and it only works for the Pi4. Indeed, the commit mentioned above was relying on the RaspberryPi firmware clocks driver to initialize the rate if it wasn't done by the firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that wasn't doing this initialization. We therefore end up with the clock not being assigned a rate, and the CPU stalling when trying to access a register. We can't move that initialization in the clk-bcm2835 driver, since the HSM clock we depend on is actually part of the HDMI power domain, so any rate setup is only valid when the power domain is enabled. Thus, we reinstated the minimum rate setup at runtime_suspend, which should address both issues. Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/ Fixes: fd5894fa2413 ("drm/vc4: hdmi: Remove clock rate initialization") Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-1-cd22e962296c@cerno.tech
2022-10-13drm/vc4: Add module dependency on hdmi-codecMaxime Ripard1-0/+1
The VC4 HDMI controller driver relies on the HDMI codec ASoC driver. In order to set it up properly, in vc4_hdmi_audio_init(), our HDMI driver will register a device matching the HDMI codec driver, and then register an ASoC card using that codec. However, if vc4 is compiled as a module, chances are that the hdmi-codec driver will be too. In such a case, the module loader will have a very narrow window to load the module between the device registration and the card registration. If it fails to load the module in time, the card registration will fail with EPROBE_DEFER, and we'll abort the audio initialisation, unregistering the HDMI codec device in the process. The next time the bind callback will be run, it's likely that we end up missing that window again, effectively preventing vc4 to probe entirely. In order to prevent this, we can create a soft dependency of the vc4 driver on the HDMI codec one so that we're sure the HDMI codec will be loaded before the VC4 module is, and thus we'll never end up in the previous situation. Fixes: 91e99e113929 ("drm/vc4: hdmi: Register HDMI codec") Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220902144111.3424560-1-maxime@cerno.tech
2022-09-14Merge drm/drm-next into drm-misc-nextMaxime Ripard1-0/+1
We need 6.0-rc1 to merge the backlight rework PR. Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-09-13drm/vc4: hdmi: Reset link on hotplugMaxime Ripard1-3/+101
During a hotplug cycle (such as a TV going out of suspend, or when the cable is disconnected and reconnected), the expectation is that the same state used before the disconnection is reused until the next commit. However, the HDMI scrambling requires that some flags are set in the monitor, and those flags are very likely to be reset when the cable has been disconnected. This will thus result in a blank display, even if the display pipeline configuration hasn't been modified or is in the exact same state. The solution we've had so far is to enable the scrambling-related bits again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 - Scrambling Control) requires that the scrambling enable bit is set before sending any scrambled video signal. Using that solution thus breaks that expectation. The solution used by i915 is to do a full modeset on the connector so that we disable the video signal, enable the scrambling bit, and enable the video signal again. As such, we took that code and plugged it into vc4. It probably could have been turned into an helper, but it proved to be difficult for several reasons: * i915 has fairly different structures than simpler KMS drivers such as vc4, so doing some code that works with both proved to be difficult; * Other simpler drivers could reuse some of it (tegra, dw-hdmi), but it would still require to move some parameters currently stored in private structure that are needed to compute whether the scrambling is needed or not, and then inform the driver that it needs to be enabled. Some of those parameters are already in core structures (drm_display_mode, drm_display_info, bpc), but the output format isnt't. Adding it is fairly challenging since unlike the TMDS char rate or mode, there's no consensus on what format to pick in drivers, so it's not possible to write some generic code that can depend on it. For these reasons, we chose to duplicate the code for now, until someone else really needs it as well, in which case we will be able to convert it into a generic helper. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Move vc4_hdmi_supports_scrambling() aroundMaxime Ripard1-17/+17
We'll need it earlier in the driver, so let's move it next to the other scrambling-related helpers. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-7-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Switch to detect_ctxMaxime Ripard1-3/+4
We'll need the locking context in future patch, so let's convert .detect to .detect_ctx. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-6-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Simplify the hotplug handlingMaxime Ripard1-22/+41
Our detect callback has a bunch of operations to perform depending on the current and last status of the connector, such a setting the CEC physical address or enabling the scrambling again. This is currently dealt with a bunch of if / else statetements that make it fairly difficult to read and extend. Let's move all that logic to a function of its own. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-5-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Remove mutex in detectMaxime Ripard2-64/+34
We recently introduced a new mutex to protect concurrent execution of ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi fields. However, using it in the detect hook was creating a reentrency issue with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect might call the CEC adap_enable hook with the lock held, eventually resulting in a deadlock. Since we didn't really need to protect anything at the moment in the CEC code, the decision was made to ignore the mutex in those CEC hooks, working around the issue. However, we can have the same thing happening if we end up triggering a mode set from the detect callback, for example using drm_atomic_helper_connector_hdmi_reset_link(). Since we don't really need to protect anything in detect either, let's just drop the lock in detect, and add it again in CEC. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Remove unused argument in vc4_hdmi_supports_scramblingMaxime Ripard1-3/+2
Even though vc4_hdmi_supports_scrambling takes a mode as an argument, it never uses it. Let's remove it. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-3-maxime@cerno.tech
2022-09-13drm/vc4: hdmi: Constify drm_display_modeMaxime Ripard2-9/+9
We don't modify the drm_display_mode pointer we have in the driver in most places, so let's make them const. Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220829134731.213478-2-maxime@cerno.tech
2022-09-11Merge tag 'drm-misc-next-2022-09-09' of git://anongit.freedesktop.org/drm/drm-misc into drm-nextDave Airlie5-98/+101
drm-misc-next for v6.1-rc1: [airlied - fix sun4i_tv build] UAPI Changes: - Hide unregistered connectors from GETCONNECTOR ioctl. - drm/virtio no longer advertises LINEAR modifier, as it doesn't work. - Cross-subsystem Changes: - Fix GPF in udmabuf failure path. Core Changes: - Rework TTM placement to use intersect/compatible functions. - Drop legacy DP-MST support. - More DP-MST related fixes, and move all state into atomic. - Make DRM_MIPI_DBI select DRM_KMS_HELPER. - Add audio_infoframe packing for DP. - Add logging when some atomic check functions fail. - Assorted documentation updates and fixes. Driver Changes: - Assorted cleanups and fixes in msm, lcdif, nouveau, virtio, panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via, bochs, qxl, sun4i. - Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels. - Improve DP-MST modeset state handling in amdgpu, nouveau, i915. - Drop DP-MST from radeon driver, it was broken and only user of legacy DP-MST. - Handle unplugging better in vc4. - Simplify drm cmdparser tests. - Add DP support to ti-sn65dsi86. - Add MT8195 DP support to mediatek. - Support RGB565, XRGB64, and ARGB64 formats in vkms. - Convert sun4i tv support to atomic. - Refactor vc4/vec TV Modesetting, and fix timings. - Use atomic helpers instead of simple display helpers in ssd130x. Maintainer changes: - Add Douglas Anderson as reviewer for panel-edp. Signed-off-by: Dave Airlie <airlied@redhat.com> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
2022-09-07drm/vc4: vec: Fix timings for VEC modesMateusz Kwiatkowski1-2/+2
This commit fixes vertical timings of the VEC (composite output) modes to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R standards. Previous timings were actually defined as 502 and 601 lines, resulting in non-standard 62.69 Hz and 52 Hz signals being generated, respectively. Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Acked-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-28-459522d653a7@cerno.tech
2022-09-07drm/vc4: vec: Remove redundant atomic_mode_setMateusz Kwiatkowski1-14/+4
Let's remove the superfluous tv_mode field, which was redundant with the mode field in struct drm_tv_connector_state. Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Reviewed-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-27-459522d653a7@cerno.tech
2022-09-07drm/vc4: vec: Refactor VEC TV mode settingMateusz Kwiatkowski1-65/+23
Change the mode_set function pointer logic to declarative config0, config1 and custom_freq fields, to make TV mode setting logic more concise and uniform. Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com> Reviewed-by: Noralf Trønnes <noralf@tronnes.org> [Maxime: Fixed != 0 check, added tv_mode variable] Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-26-459522d653a7@cerno.tech
2022-09-07drm/vc4: vec: Convert to atomic helpersMaxime Ripard1-4/+6
The VC4 VEC driver still uses legacy enable and disable hook implementation. Let's convert to the atomic variants. Reviewed-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-25-459522d653a7@cerno.tech
2022-09-07drm/vc4: vec: Remove empty mode_fixupMaxime Ripard1-9/+0
The mode_fixup hooks are deprecated, and the behaviour we implement is the default one anyway. Let's remove it. Reviewed-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-24-459522d653a7@cerno.tech
2022-09-06Merge tag 'drm-misc-next-2022-08-20-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-nextDaniel Vetter22-690/+1260
drm-misc-next for v6.1: UAPI Changes: Cross-subsystem Changes: - DMA-buf: documentation updates. - Assorted small fixes to vga16fb - Fix fbdev drivers to use the aperture helpers. - Make removal of conflicting drivers work correctly without fbdev enabled. Core Changes: - bridge, scheduler, dp-mst: Assorted small fixes. - Add more format helpers to fourcc, and use it to replace the cpp usage. - Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx ("darkness", inverted single channel) - Add packed AYUV8888 and XYUV8888 formats. - Assorted documentation updates. - Rename ttm_bo_init to ttm_bo_init_validate. - Allow TTM bo's to exist without backing store. - Convert drm selftests to kunit. - Add managed init functions for (panel) bridge, crtc, encoder and connector. - Fix endianness handling in various format conversion helpers. - Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565 - Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so drm_plane_helper is no longer needed in most drivers. - Use idr_init_base instead of idr_init. - Rename FB and GEM CMA helpers to DMA helpers. - Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that takes a iosys_map. Make drm_fb_memcpy take an iosys_map too. - Move edid luminance calculation to core, and use it in i915. Driver Changes: - bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767}, nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111: Assorted small fixes and doc updates. - vc4: Rework hdmi power up, and depend on PM. - panel/simple: Add Samsung LTL101AL01. - ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property is unchanged, and use the new PM ops. - Revert some amdgpu commits that cause garbaged graphics when starting X, and reapply them with the real problem fixed. - Completely rework vc4 init to use managed helpers. - Rename via_drv to via_dri1, and move all stuff there only used by the dri1 implementation in preperation for atomic modeset. - Use regmap bulk write in ssd130x. - Power sequence and clock updates to it6505. - Split panel-sitrox-st7701 init sequence and rework mode programming code. - virtio: Improve error and edge conditions handling, and convert to use managed helpers. - Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels. - Add generic fbdev support to komeda. - Split mgag200 modeset handling to make it more model-specific. - Convert simpledrm to use atomic helpers. - Improve udl suspend/disconnect handling. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/f0c71766-61e8-19b7-763a-5fbcdefc633d@linux.intel.com
2022-08-25drm/vc4: hvs: protect drm_print_regset32()Danilo Krummrich1-2/+2
In vc4_hvs_dump_state() potentially freed resources are protected from being accessed with drm_dev_enter()/drm_dev_exit(). Also include drm_print_regset32() in the protected section, since drm_print_regset32() does access memory that is typically mapped via devm_* calls. Fixes: 969cfae1f01d ("drm/vc4: hvs: Protect device resources after removal") Signed-off-by: Danilo Krummrich <dakr@redhat.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220824161327.330627-5-dakr@redhat.com
2022-08-25drm/vc4: crtc: protect device resources after removalDanilo Krummrich1-1/+40
(Hardware) resources which are bound to the driver and device lifecycle must not be accessed after the device and driver are unbound. However, the DRM device isn't freed as long as the last user closed it, hence userspace can still call into the driver. Therefore protect the critical sections which are accessing those resources with drm_dev_enter() and drm_dev_exit(). Fixes: 7cc4214c27cf ("drm/vc4: crtc: Switch to drmm_kzalloc") Signed-off-by: Danilo Krummrich <dakr@redhat.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220824161327.330627-4-dakr@redhat.com
2022-08-25drm/vc4: plane: protect device resources after removalDanilo Krummrich1-0/+20
(Hardware) resources which are bound to the driver and device lifecycle must not be accessed after the device and driver are unbound. However, the DRM device isn't freed as long as the last user closed it, hence userspace can still call into the driver. Therefore protect the critical sections which are accessing those resources with drm_dev_enter() and drm_dev_exit(). Fixes: 9872c7a31921 ("drm/vc4: plane: Switch to drmm_universal_plane_alloc()") Signed-off-by: Danilo Krummrich <dakr@redhat.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220824161327.330627-3-dakr@redhat.com
2022-08-25drm/vc4: hdmi: unlock mutex when device is unpluggedDanilo Krummrich1-2/+5
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187bf ("drm/vc4: hdmi: Protect device resources after removal") missed to unlock the mutex before returning due to drm_dev_enter() indicating the device being unplugged. Fixes: cd00ed5187bf ("drm/vc4: hdmi: Protect device resources after removal") Signed-off-by: Danilo Krummrich <dakr@redhat.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220824161327.330627-2-dakr@redhat.com
2022-08-18drm/vc4: hdmi: Rework power upMaxime Ripard1-8/+7
The current code tries to handle the case where CONFIG_PM isn't selected by first calling our runtime_resume implementation and then properly report the power state to the runtime_pm core. This allows to have a functionning device even if pm_runtime_get_* functions are nops. However, the device power state if CONFIG_PM is enabled is RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls in the runtime_pm hooks will now report a warning since the device might not be properly powered. Even more so, we need CONFIG_PM enabled since the previous RaspberryPi have a power domain that needs to be powered up for the HDMI controller to be usable. The previous patch has created a dependency on CONFIG_PM, now we can just assume it's there and only call pm_runtime_resume_and_get() to make sure our device is powered in bind. Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> (cherry picked from commit 53565c28e6af2cef6bbf438c34250135e3564459) Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-08-18drm/vc4: hdmi: Depends on CONFIG_PMMaxime Ripard2-1/+2
We already depend on runtime PM to get the power domains and clocks for most of the devices supported by the vc4 driver, so let's just select it to make sure it's there. Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.tech Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> (cherry picked from commit f1bc386b319e93e56453ae27e9e83817bb1f6f95) Signed-off-by: Maxime Ripard <maxime@cerno.tech>
2022-08-15drm/vc4: Drop of_gpio headerMaíra Canal1-1/+0
This driver includes the deprecated OF GPIO header <linux/of_gpio.h> yet fail to use symbols from it, so drop the include. Cc: Emma Anholt <emma@anholt.net> Cc: Maxime Ripard <mripard@kernel.org> Signed-off-by: Maíra Canal <mairacanal@riseup.net> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220812205746.609107-6-mairacanal@riseup.net
2022-08-06Merge tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds1-0/+1
Pull sound updates from Takashi Iwai: "As the diffstat shows, we've had lots of developments in a wide range at this time; the majority of changes are about ASoC, including subsystem-wide cleanups, continued SOF / Intel updates and a bunch of new drivers (as usual), while there have been some significant (but almost invisible) improvements in ALSA core side, too. Below are some highlights: Core: - Faster lookups of control elements with Xarray; normal user won't notice, but on the devices with tons of control elements, it can be visibly faster - Support for input validation for controls; this will harden for badly written drivers in general with a slight overhead - Deferred async signal handling for working around the potential deadlocks - Cleanup / refactoring raw MIDI locking code ASoC: - Restructing of the set_fmt() callbacks for making things clearer in situations like CODEC to CODEC links - Clean up and modernizing the DAI naming scheme setups - Merge of more of the Intel AVS driver stack, including some board integrations - New version 4 mechanism for communication with SOF DSPs - Suppoort for dynamically selecting the PLL to use at runtime on i.MX platforms - Improvements for CODEC to CODEC support in the generic cards - Support for AMD Jadeite and various machines, AMD RPL, Intel MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments TAS2780 HD- and USB-audio: - Continued improvement for CS35L41 (sub)codec support - More quirks for various devices (HP, Lenovo, Dell, Clevo)" * tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits) ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx ALSA: line6: Replace sprintf() with sysfs_emit() ALSA: hda: Replace sprintf() with sysfs_emit() ALSA: pcm: Replace sprintf() with sysfs_emit() ALSA: core: Replace scnprintf() with sysfs_emit() ALSA: control-led: Replace sprintf() with sysfs_emit() ALSA: aoa: Replace sprintf() with sysfs_emit() ALSA: ac97: Replace sprintf() with sysfs_emit() ALSA: hda/realtek: Add quirk for Clevo NV45PZ ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7 ALSA: control: Use deferred fasync helper ALSA: pcm: Use deferred fasync helper ALSA: timer: Use deferred fasync helper ALSA: core: Add async signal helpers ASoC: q6asm: use kcalloc() instead of kzalloc() ACPI: scan: Add CLSA0101 Laptop Support ALSA: hda: cs35l41: Support CLSA0101 ALSA: hda: cs35l41: Use the CS35L41 HDA internal define ASoC: dt-bindings: use spi-peripheral-props.yaml ASoC: codecs: va-macro: use fsgen as clock ...
2022-08-03drm/gem: rename struct drm_gem_dma_object.{paddr => dma_addr}Danilo Krummrich8-24/+24
The field paddr of struct drm_gem_dma_object holds a DMA address, which might actually be a physical address. However, depending on the platform, it can also be a bus address or a virtual address managed by an IOMMU. Hence, rename the field to dma_addr, which is more applicable. In order to do this renaming the following coccinelle script was used: ``` @@ struct drm_gem_dma_object *gem; @@ - gem->paddr + gem->dma_addr @@ struct drm_gem_dma_object gem; @@ - gem.paddr + gem.dma_addr @exists@ typedef dma_addr_t; symbol paddr; @@ dma_addr_t paddr; <... - paddr + dma_addr ...> @@ symbol paddr; @@ dma_addr_t - paddr + dma_addr ; ``` This patch is compile-time tested with: ``` make ARCH={x86_64,arm,arm64} allyesconfig make ARCH={x86_64,arm,arm64} drivers/gpu/drm` ``` Acked-by: Sam Ravnborg <sam@ravnborg.org> Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-5-dakr@redhat.com
2022-08-03drm/gem: rename GEM CMA helpers to GEM DMA helpersDanilo Krummrich12-71/+71
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM DMA" seems to be more applicable. Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers") requests to rename the CMA helpers and implies that people seem to be confused about the naming. In order to do this renaming the following script was used: ``` #!/bin/bash DIRS="drivers/gpu include/drm Documentation/gpu" REGEX_SYM_UPPER="[0-9A-Z_\-]" REGEX_SYM_LOWER="[0-9a-z_\-]" REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)" REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)" REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g" REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g" # Find all upper case 'CMA' symbols and replace them with 'DMA'. for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS) do sed -i -E "$REGEX_SED_UPPER" $ff done # Find all lower case 'cma' symbols and replace them with 'dma'. for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS) do sed -i -E "$REGEX_SED_LOWER" $ff done # Replace all occurrences of 'CMA' / 'cma' in comments and # documentation files with 'DMA' / 'dma'. for ff in $(grep -RiHl " cma " $DIRS) do sed -i -E "s/ cma / dma /g" $ff sed -i -E "s/ CMA / DMA /g" $ff done # Rename all 'cma_obj's to 'dma_obj'. for ff in $(grep -RiHl "cma_obj" $DIRS) do sed -i -E "s/cma_obj/dma_obj/g" $ff done ``` Only a few more manual modifications were needed, e.g. reverting the following modifications in some DRM Kconfig files - select CMA if HAVE_DMA_CONTIGUOUS + select DMA if HAVE_DMA_CONTIGUOUS as well as manually picking the occurrences of 'CMA'/'cma' in comments and documentation which relate to "GEM CMA", but not "FB CMA". Also drivers/gpu/drm/Makefile was fixed up manually after renaming drm_gem_cma_helper.c to drm_gem_dma_helper.c. This patch is compile-time tested building a x86_64 kernel with `make allyesconfig && make drivers/gpu/drm`. Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
2022-08-03drm/fb: rename FB CMA helpers to FB DMA helpersDanilo Krummrich3-11/+11
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be more applicable. Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers") requests to rename the CMA helpers and implies that people seem to be confused about the naming. In order to do this renaming the following script was used: ``` #!/bin/bash DIRS="drivers/gpu include/drm Documentation/gpu" REGEX_SYM_UPPER="[0-9A-Z_\-]" REGEX_SYM_LOWER="[0-9a-z_\-]" REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)" REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)" REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g" REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g" # Find all upper case 'CMA' symbols and replace them with 'DMA'. for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS) do sed -i -E "$REGEX_SED_UPPER" $ff done # Find all lower case 'cma' symbols and replace them with 'dma'. for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS) do sed -i -E "$REGEX_SED_LOWER" $ff done # Replace all occurrences of 'CMA' / 'cma' in comments and # documentation files with 'DMA' / 'dma'. for ff in $(grep -RiHl " cma " $DIRS) do sed -i -E "s/ cma / dma /g" $ff sed -i -E "s/ CMA / DMA /g" $ff done ``` Only a few more manual modifications were needed, e.g. reverting the following modifications in some DRM Kconfig files - select CMA if HAVE_DMA_CONTIGUOUS + select DMA if HAVE_DMA_CONTIGUOUS as well as manually picking the occurrences of 'CMA'/'cma' in comments and documentation which relate to "FB CMA", but not "GEM CMA". This patch is compile-time tested building a x86_64 kernel with `make allyesconfig && make drivers/gpu/drm`. Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-3-dakr@redhat.com
2022-08-03drm/fb: remove unused includes of drm_fb_cma_helper.hDanilo Krummrich1-1/+0
Quite a lot of drivers include the drm_fb_cma_helper.h header file without actually making use of it's provided API, hence remove those includes. Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-2-dakr@redhat.com
2022-07-26drm: Remove unnecessary include statements of drm_plane_helper.hThomas Zimmermann2-2/+0
Remove the include statement for drm_plane_helper.h from all the files that don't need it. Althogh the header file is almost empty, many drivers include it somewhere. Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220720083058.15371-5-tzimmermann@suse.de
2022-07-13drm/vc4: v3d: Switch to devm_pm_runtime_enableMaxime Ripard1-7/+4
devm_pm_runtime_enable() simplifies the driver a bit since it will call pm_runtime_disable() automatically through a device-managed action. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-70-maxime@cerno.tech
2022-07-13drm/vc4: v3d: Rework the runtime_pm setupMaxime Ripard1-15/+22
At bind time, vc4_v3d_bind() will read a register to retrieve the v3d version and make sure it's a version we're compatible with. However, the v3d has an optional clock that is enabled only after the register read-out and a power domain that wasn't enabled at all in the bind implementation. This was working fine at boot because both were enabled, but resulted in the version check failing if we were unbinding and rebinding the driver because the unbinding would have turned them off. The fix isn't as easy as calling pm_runtime_resume_and_get() prior to the register access to power up the power domain though. Indeed, the runtime_resume implementation will enable the clock mentioned above, call vc4_v3d_init_hw() and then vc4_irq_enable(). Prior to the previous patch, vc4_irq_enable() needed to occur after our call to platform_get_irq() and vc4_irq_install(), since vc4_irq_enable() used to call enable_irq() and vc4_irq_install() will call request_irq(). vc4_irq_install() will also do some register access, so needs the power domain to be on. So we ended up in a situation where vc4_v3d_runtime_resume() needed vc4_irq_install() to have been called before, and vc4_irq_install() needed vc4_v3d_runtime_resume(). The previous patch removed the enable_irq() call in vc4_irq_enable() and thus removed the dependency of vc4_v3d_runtime_resume() on vc4_irq_install(). Thus, we can now rework our bind implementation to call pm_runtime_resume_and_get() before our register access to make sure the power domain is on. vc4_v3d_runtime_resume() also takes care of turning the clock on and calling vc4_v3d_init_hw() so we can remove them from bind. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-69-maxime@cerno.tech
2022-07-13drm/vc4: v3d: Stop disabling interruptsMaxime Ripard2-3/+1
The vc4_irq_disable(), among other things, will call disable_irq() to complete any in-flight interrupts. This requires its counterpart, vc4_irq_enable(), to call enable_irq() which causes issues addressed in a later patch. However, vc4_irq_disable() is called by two callees: vc4_irq_uninstall() and vc4_v3d_runtime_suspend(). vc4_irq_uninstall() also calls free_irq() which already disables the interrupt line. We thus don't require an explicit disable_irq() for that call site. vc4_v3d_runtime_suspend() doesn't have any other code. However, the rest of vc4_irq_disable() masks the interrupts coming from the v3d, so explictly disabling the interrupt line is also redundant. The only thing we really care about is thus to make sure we don't have any handler in-flight, as suggested by the comment. We can thus replace disable_irq() by synchronize_irq(). Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-68-maxime@cerno.tech
2022-07-13drm/vc4: perfmon: Add missing mutex_destroyMaxime Ripard1-0/+1
vc4_perfmon_open_file() will instantiate a mutex for that file instance, but we never call mutex_destroy () in vc4_perfmon_close_file(). Let's add that missing call. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-67-maxime@cerno.tech
2022-07-13drm/vc4: Switch to drmm_mutex_initMaxime Ripard4-6/+28
mutex_init is supposed to be balanced by a call to mutex_destroy that we were never doing in the vc4 driver. Since a DRM-managed mutex_init variant has been introduced, let's just switch to it. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-66-maxime@cerno.tech
2022-07-13drm/vc4: debugfs: Simplify debugfs registrationMaxime Ripard11-69/+191
The vc4 has a custom API to allow components to register a debugfs file before the DRM driver has been registered and the debugfs_init hook has been called. However, the .late_register hook allows to have the debugfs file creation deferred after that time already. Let's remove our custom code to only register later our debugfs entries as part of either debugfs_init or after it. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-65-maxime@cerno.tech
2022-07-13drm/vc4: debugfs: Return an error on failureMaxime Ripard2-23/+27
vc4_debugfs_add_file() can fail, so let's propagate its error code instead of silencing it. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-64-maxime@cerno.tech
2022-07-13drm/vc4: debugfs: Protect device resourcesMaxime Ripard1-0/+9
Our current code now mixes some resources whose lifetime are tied to the device (clocks, IO mappings, etc.) and some that are tied to the DRM device (encoder, bridge). The device one will be freed at unbind time, but the DRM one will only be freed when the last user of the DRM device closes its file handle. So we end up with a time window during which we can call the encoder hooks, but we don't have access to the underlying resources and device. Let's protect all those sections with drm_dev_enter() and drm_dev_exit() so that we bail out if we are during that window. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-63-maxime@cerno.tech
2022-07-13drm/vc4: vec: Switch to devm_pm_runtime_enableMaxime Ripard1-15/+5
devm_pm_runtime_enable() simplifies the driver a bit since it will call pm_runtime_disable() automatically through a device-managed action. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-62-maxime@cerno.tech
2022-07-13drm/vc4: vec: Protect device resources after removalMaxime Ripard1-6/+61
Whenever the device and driver are unbound, the main device and all the subdevices will be removed by calling their unbind() method. However, the DRM device itself will only be freed when the last user will have closed it. It means that there is a time window where the device and its resources aren't there anymore, but the userspace can still call into our driver. Fortunately, the DRM framework provides the drm_dev_enter() and drm_dev_exit() functions to make sure our underlying device is still there for the section protected by those calls. Let's add them to the VEC driver. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-61-maxime@cerno.tech
2022-07-13drm/vc4: vec: Switch to DRM-managed connector initializationMaxime Ripard1-6/+5
The current code will call drm_connector_unregister() and drm_connector_cleanup() when the device is unbound. However, by then, there might still be some references held to that connector, including by the userspace that might still have the DRM device open. Let's switch to a DRM-managed initialization to clean up after ourselves only once the DRM device has been last closed. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-60-maxime@cerno.tech
2022-07-13drm/vc4: vec: Switch to DRM-managed encoder initializationMaxime Ripard1-5/+9
The current code will call drm_encoder_cleanup() when the device is unbound. However, by then, there might still be some references held to that encoder, including by the userspace that might still have the DRM device open. Let's switch to a DRM-managed initialization to clean up after ourselves only once the DRM device has been last closed. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-59-maxime@cerno.tech
2022-07-13drm/vc4: vec: Remove call to drm_connector_unregister()Maxime Ripard1-8/+2
drm_connector_unregister() is only to be used for connectors that have been registered through drm_connector_register() after drm_dev_register() has been called. This is our case here so let's remove the call. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-58-maxime@cerno.tech
2022-07-13drm/vc4: vec: Switch to drmm_kzallocMaxime Ripard1-1/+1
Our internal structure that stores the DRM entities structure is allocated through a device-managed kzalloc. This means that this will eventually be freed whenever the device is removed. In our case, the most likely source of removal is that the main device is going to be unbound, and component_unbind_all() is being run. However, it occurs while the DRM device is still registered, which will create dangling pointers, eventually resulting in use-after-free. Switch to a DRM-managed allocation to keep our structure until the DRM driver doesn't need it anymore. Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20220711173939.1132294-57-maxime@cerno.tech
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.