| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[ 20.740134] c0 3136 (Compiler) Call trace:
[ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
//
// If CPU0 has just finished "is_done_rcv = true" in path1, and at
// this moment, IRQ or ICache line missing happens in CPU0.
// What happens in CPU1 (path2)?
//
// If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
// path2 would have chance to break from wait_event_interruptible
// in mmc_wait_for_data_req_done and continue to run for next
// mmc_request (mmc_blk_rw_rq_prep).
//
// Within mmc_blk_rq_prep, mrq is cleared to 0.
// If below line still gets host from "mrq" as the result of
// compiler, the panic happens as we traced.
wake_up_interruptible(&mrq->host->context_info.wait);
}
path2: CPU1: <The mmcqd thread runs mmc_queue_thread>
static int mmc_wait_for_data_req_done(...
{
...
while (1) {
wait_event_interruptible(context_info->wait,
(context_info->is_done_rcv ||
context_info->is_new_req));
static void mmc_blk_rw_rq_prep(...
{
...
memset(brq, 0, sizeof(struct mmc_blk_request));
This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
+ mdelay(1);
wake_up_interruptible(&mrq->host->context_info.wait);
}
At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).
This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 2220eedfd7ae ("mmc: fix async request mechanism ....")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use more compact of_property_read_bool() calls instead of the
of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When requesting a trim for several bytes, everything up to the next
erase-group is erased. This causes data corruption.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Other subsystem buses attach PM domains during probe, but prior calling
the driver's ->probe() method. During the removal phase, detaching the PM
domain will be done after invoking the driver's ->remove() callback.
Convert the SDIO bus to follow this behavior and add error handling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since the ->reset() callback is implemented for SD, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since the ->reset() callback is implemented for MMC, the ->power_restore()
callback has become redundant, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.
Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
IO state variable drv_type could be set during card
initialization. Consequently, it must be reset to the
default value when setting the initial state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since the regulator used for the SDMMC IO voltage is not expected to
draw a lot of current, most systems will probably use an inexpensive
LDO for it. LDO regulators apparently have the feature that they
don't actively drive the voltage down--they wait for other components
in the system to drag the voltage down. Thus they will transition
faster under heavy loads and slower under light loads.
During an SDMMC voltage change from 3.3V to 1.8V, we are almost
certainly under a light load. To be specific:
* The regulator is hooked through pulls to CMD0-3 and DAT. Probably
the CMD pulls are something like 47K and the DAT is something like
10K.
* The card is supposed to be driving DAT0-3 low during voltage change
which will draw _some_ current, but not a lot.
* The regulator is also provided to the SDMMC host controller, but the
SDMMC host controller is in open drain mode during the voltage
change and so shouldn't be drawing much current.
In order to keep the SDMMC host working properly (or for noise
reasons), there might also be a capacitor attached to the SDMMC IO
regulator. This also will have the effect of slowing down transitions
of the regulator, especially under light loads.
From experimental evidence, we've seen the voltage change fail if the
card doesn't detect that the voltage fell to less than about 2.3V when
we turn on the clock. On one device (that admittedly had a 47K CMD
pullup instead of a 10K CMD pullup) we saw that the voltage was just
about 2.3V after 5ms and thus the voltage change would sometimes fail.
Doubling the delay gave margin and made the voltage change work 100%
of the time, despite the slightly weaker CMD pull.
At the moment submitting this as an RFC patch since my problem _could_
be fixed by increasing the pull strength (or using a smaller
capacitor). However being a little bit more lenient to strange
hardware could also be a good thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
card->ext_csd.enhanced_area_offset is defined as "unsigned long long",
and, ext_csd[] is defined as u8.
unsigned long long data might have strange data if first bit of ext_csd[]
was 1. this patch cast it to (unsigned long long)
Special thanks to coverity <http://www.coverity.com>
ex)
u8 data8;
u64 data64;
data8 = 0x80;
data64 = (data8 << 24); // 0xffffffff80000000
data64 = (((unsigned long long)data8) << 24); // 0x80000000;
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is not uncommon to see systems where there is no physical write-protect
signal (e.g. when using eMMC or microSD card slots). For some controllers,
which have a dedicated write-protection detection logic (like SDHCI
controllers), the get_ro() callback can return bogus data in such a case.
Instead of handling this on a per controller basis this patch adds a new
capability flag to the MMC core that can be set to specify that the result
of get_ro() is invalid. When the flag is set the core will not call
get_ro() and assume that the card is always read-write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Check the error code for EOPNOTSUPP and do not print
reset warning in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CRC errors could possibly be alleviated by
re-tuning so flag re-tuning needed in those cases.
Note this has no effect if re-tuning has not been
enabled.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
HS400 re-tuning must be done in HS200 mode. Add
the ability to switch from HS400 mode to HS200
mode before re-tuning and switch back to HS400
after re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make a separate function to do the mmc_switch status check
so it can be re-used. This is preparation for adding support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sleep command is issued after deselecting the
card, but re-tuning won't work on a deselected card
so re-tuning must be held.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during bkops to prevent
it from conflicting with the busy state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during erase commands to prevent
it from conflicting with the sequence of commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during switch commands to prevent
it from conflicting with the busy state or the CMD13
verification.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
At the start of each request, re-tune if needed and
then hold off re-tuning again until the request is done.
Note that though there is one function that starts
requests (mmc_start_request) there are two that wait for
the request to be done (mmc_wait_for_req_done and
mmc_wait_for_data_req_done). Also note that
mmc_wait_for_data_req_done can return even when the
request is not done (which allows the block driver
to prepare a newly arrived request while still
waiting for the previous request).
This patch ensures re-tuning is held for the duration
of a request. Subsequent patches will also hold
re-tuning at other times when it might cause a
conflict.
In addition, possibly a command is failing because
re-tuning is needed. Use mmc_retune_recheck() to check
re-tuning. At that point re-tuning is held, at least by
the request, so mmc_retune_recheck() flags host->retune_now
if the hold count is 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enable re-tuning when tuning is executed and
disable re-tuning when card is no longer initialized.
In the case of SDIO suspend, the card can keep power.
In that case, re-tuning need not be disabled, but, if
a re-tuning timer is being used, ensure it is disabled
and assume that re-tuning will be needed upon resume
since it is not known how long the suspend will last.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently, there is core support for tuning during
initialization. There can also be a need to re-tune
periodically (e.g. sdhci) or to re-tune after the
host controller is powered off (e.g. after PM
runtime suspend / resume) or to re-tune in response
to CRC errors.
The main requirements for re-tuning are:
- ability to enable / disable re-tuning
- ability to flag that re-tuning is needed
- ability to re-tune before any request
- ability to hold off re-tuning if the card is busy
- ability to hold off re-tuning if re-tuning is in
progress
- ability to run a re-tuning timer
To support those requirements 7 members are added to struct
mmc_host:
unsigned int can_retune:1; /* re-tuning can be used */
unsigned int doing_retune:1; /* re-tuning in progress */
unsigned int retune_now:1; /* do re-tuning at next req */
int need_retune; /* re-tuning is needed */
int hold_retune; /* hold off re-tuning */
unsigned int retune_period; /* re-tuning period in secs */
struct timer_list retune_timer; /* for periodic re-tuning */
need_retune is an integer so it can be set without needing
synchronization. hold_retune is a integer to allow nesting.
Various simple functions are provided to set / clear those
variables.
Subsequent patches take those functions into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some drivers schedule automatic hw resets. An example is mwifiex,
which schedules a card reset if the command handler between driver
and card firmware becomes out of sync
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(),
as result mmc_rescan() could be scheduled and executed at
late hibernation restore stages when MMC device is suspended
already - which, in turn, will lead to system crash on TI dra7-evm board:
WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access
Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify().
Fixes: 4c2ef25fe0b8 (mmc: fix all hangs related to mmc/sd card...)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit 6685ac62b2f0 ("mmc: core: Convert mmc_driver to
device_driver")
The reverted commit went too far in simplifing the device driver parts
for mmc.
Let's restore the old mmc_driver to enable driver core to sooner
or later to remove the ->probe(), ->remove() and ->shutdown() callbacks
from the struct device_driver.
Note that, the old ->suspend|resume() callbacks in the struct
mmc_driver don't need to be restored, since the mmc block layer has
converted to the modern system PM ops.
Fixes: 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
If the struct mmc_pwrseq_match .alloc function used to allocate a
struct mmc_pwrseq fails, the error is propagated to mmc_of_parse().
But instead of returning the error code in pwrseq, host->pwrseq is
returned which will always be 0. So mmc_of_parse() succeeds even if
the pwrseq .alloc function failed and host->pwrseq is NULL.
This makes the SDIO device to not be powered if the power sequencing
.alloc functions wants to be deferred due a missing resource because
the mmc controller driver probe did wrongly succeed.
Fixes: 0f12a0ce4ce4a ("mmc: pwrseq: simplify alloc/free hooks")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
|
|
The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:
mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_HPI_MGMT, 1,
card->ext_csd.generic_cmd6_time);
There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently those host drivers which have deployed runtime PM, deals with
the runtime PM reference counting entirely by themselves.
Since host drivers don't know when the core will send the next request
through some of the host_ops callbacks, they need to handle runtime PM
get/put between each an every request.
In quite many cases this has some negative effects, since it leads to a
high frequency of scheduled runtime PM suspend operations. That due to
the runtime PM reference count will normally reach zero in-between
every request.
We can decrease that frequency, by enabling the core to deal with
runtime PM reference counting of the host device. Since the core often
knows that it will send a seqeunce of requests, it makes sense for it
to keep a runtime PM reference count during these periods.
More exactly, let's increase the runtime PM reference count by invoking
pm_runtime_get_sync() from __mmc_claim_host(). Restore that action by
invoking pm_runtime_mark_last_busy() and pm_runtime_put_autosuspend()
in mmc_release_host(). In this way a runtime PM reference count will be
kept during the complete cycle of a claim -> release host.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Konstantin Dorfman <kdorfman@codeaurora.org>
|
|
These callbacks have been set to deprecated for some time. The last
user (omap_hsmmc) has moved away from using them, which thus enables
us to completely remove them.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().
To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The alloc() and free() hooks required each pwrseq implementation to set
host->pwrseq themselves. This is error-prone and could be done at a
higher level if alloc() was changed to return a pointer to a struct
mmc_pwrseq instead of an error code.
This patch performs this change and moves the burden of maintaining
host->pwrseq from the power sequence hooks to the pwrseq code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f48330ed695927a51fa068dc5d673f2da19
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
|
|
This patch fix spelling typo in printk messages.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch provides a simple mmc-pwrseq-emmc driver, which controls
single gpio line. It perform standard eMMC hw reset procedure, as
descibed by Jedec 4.4 specification. This procedure is performed just
after MMC core enabled power to the given mmc host (to fix possible
issues if bootloader has left eMMC card in initialized or unknown
state), and before performing complete system reboot (also in case of
emergency reboot call). The latter is needed on boards, which doesn't
have hardware reset logic connected to emmc card and (limited or broken)
ROM bootloaders are unable to read second stage from the emmc card if
the card is left in unknown or already initialized state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Host drivers have different ways to sends their "init stream" to the
card. Some need to do it as part of a request, some do it from the
->set_ios() callback in the MMC_POWER_ON state and some don't send an
"init stream" at all.
To be able to use the reset GPIOs from the simple MMC power sequence
provider, the card need to be powered and the "init stream" must not
have been sent.
To cope with these requirements, invoke mmc_pwrseq_post_power_on()
prior we change the state to MMC_POWER_ON in mmc_power_up().
Host drivers shall perform power up operations in the MMC_POWER_UP
state. Unfortunate three hosts (au1xmmc, cb710-mmc and toshsd) don't
conform to this expectation. Instead those ignore the MMC_POWER_UP
state and delays their power up operations to the MMC_POWER_ON state.
Those hosts needs to change their behavior to enable proper support for
the simple MMC power sequence provider.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
Some WLAN chips attached to a SDIO interface, need a reference clock.
Since this is very common, extend the prseq_simple driver to support
an optional clock that is enabled prior the card power up procedure.
Note: the external clock is optional. Thus an error is not returned
if the clock is not found.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Many WLAN attached to a SDIO/MMC interface, needs more than one pin for
their reset sequence. For example, is very common for chips to have two
pins: one for reset and one for power enable.
This patch adds support for more reset pins to the pwrseq_simple driver
and instead hardcoding a fixed number, it uses the of_gpio_named_count()
since the MMC power sequence is only built when CONFIG_OF is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch is coming to fix compatibility issue of BKOPS_EN field of EXT_CSD.
In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits:
Bit 0 - MANUAL_EN
Bit 1 - AUTO_EN
In previous eMMC revisions, only Bit 0 was supported.
Signed-off-by: Alexey Skidanov <alexey.skidanov@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The need for reset GPIOs has several times been pointed out from
erlier posted patchsets. Especially some WLAN chips which are
attached to an SDIO interface may use a GPIO reset.
The reset GPIO is asserted at initialization and prior we start the
power up procedure. The GPIO will be de-asserted right after the power
has been provided to the card, from the ->post_power_on() callback.
Note, the reset GPIO is optional. Thus we don't return an error even if
we can't find a GPIO for the consumer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
To add the core part for the MMC power sequence, let's start by adding
initial support for the simple MMC power sequence provider.
In this initial step, the MMC power sequence node are fetched and the
compatible string for the simple MMC power sequence provider are
verified.
At this point we don't parse the node for any properties, but instead
that will be handled from following patches. Since there are no
properties supported yet, let's just implement the ->alloc() and the
->free() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
Jialing Fu
Shawn Lin
Sergei Shtylyov
Robin van der Gracht
David Jander
Ulf Hansson
Adrian Hunter
Doug Anderson
Kuninori Morimoto
Lars-Peter Clausen
Andreas Fenkart
Grygorii Strashko
Javier Martinez Canillas
Linus Torvalds
Hans de Goede
NeilBrown
NeilBrown
Alexandre Courbot
Masanari Iida
Marek Szyprowski
Alexey Skidanov