| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The commit 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc385e ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The allocated normal volumes saved in ubi->volumes are not freed
in the error paths in ubi_attach_mtd_dev() and its callees (e.g.
ubi_attach() and ubi_read_volume_table()).
These normal volumes should be freed through kill_volumes() and
vol_release(), but ubi_attach_mtd_dev() may fail before
calling uif_init(), and there will be memory leaks.
So adding a new helper ubi_free_all_volumes() to free the normal
and the internal volumes. And in order to prevent double-free
of volume, reset ubi->volumes[i] to NULL after freeing.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Else there may be oops when fastmap is enabled and init_volumes() fails.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/ubi/wl.c: In function 'find_wl_entry':
drivers/mtd/ubi/wl.c:322:27: warning:
variable 'prev_e' set but not used [-Wunused-but-set-variable]
It's not used any more now, so remove it.
Fixes: f9c34bb52997 ("ubi: Fix producing anchor PEBs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb00840 ("ubi: Use bitmaps in Fastmap self-check code")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The ops aren't used in any SPI NOR controller. Therefore, remove them
altogether.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Intel Comet Lake-V has the same SPI serial flash controller as Kaby
Lake. Add Comet Lake-V PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The driver is for the HiSilicon FMC (Flash Memory Controller), which
supports SPI NOR in addition other memory technologies, like SPI NAND.
Indeed, the naming in the driver is a little inappropriate, especially
considering that there is already another HiSilicon SPI NOR flash
controller (which I believe the FMC is derived from).
Since we now want to provide software support for this other HiSilicon
controller, update code comments to at least try to make it clear that
this driver is for the FMC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Adds support for sst26vf016b, a smaller variant of the sst26vf064b.
Tested on a sama5d3 SOC using the atmel,at91rm9200-spi controller.
The dual read could not be tested.
SPI_NOR_QUAD_READ is not added because it requires that the IOC bit
from the Configuration Register to be set to 1, which is not the case:
its default value at power-up is zero and we don't set it to one in
spi-nor either.
Signed-off-by: Joseph Kust <joseph.kust@rockwellcollins.com>
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
[tudor.ambarus@microchip.com: Drop quad read flag, amend commit description]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
With gcc -O3, we get a new warning:
In file included from arch/arm64/include/asm/processor.h:28,
from drivers/mtd/sm_ftl.c:8:
In function 'memset',
inlined from 'sm_read_sector.constprop' at drivers/mtd/sm_ftl.c:250:3:
include/linux/string.h:411:9: error: argument 1 null where non-null expected [-Werror=nonnull]
return __builtin_memset(p, c, size);
>From all I can tell, this cannot happen (the function is called
either with a NULL buffer or with a -1 block number but not both),
but adding a check makes it more robust and avoids the warning.
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de2c5 (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The __iomem memory should be copied with memcpy_fromio. This fixes
Sparse warnings like:
drivers/mtd/nand/onenand/samsung_mtd.c:678:40: warning: incorrect type in argument 2 (different address spaces)
drivers/mtd/nand/onenand/samsung_mtd.c:678:40: expected void const *from
drivers/mtd/nand/onenand/samsung_mtd.c:678:40: got void [noderef] <asn:2> *[assigned] p
drivers/mtd/nand/onenand/samsung_mtd.c:679:19: warning: incorrect type in assignment (different address spaces)
drivers/mtd/nand/onenand/samsung_mtd.c:679:19: expected void [noderef] <asn:2> *[assigned] p
drivers/mtd/nand/onenand/samsung_mtd.c:679:19: got unsigned char *
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Correct mispelling, spacing, and coding style flaws caught by
checkpatch.pl script in the Omap2 Onenand driver .
Signed-off-by: Amir Mahdi Ghorbanian <indigoomega021@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328c1 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f857f ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Fix typo s/JESB216/JESD216/
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
|
|
Pull UBI/UBIFS/JFFS2 updates from Richard Weinberger:
"This pull request contains mostly fixes for UBI, UBIFS and JFFS2:
UBI:
- Fix a regression around producing a anchor PEB for fastmap.
Due to a change in our locking fastmap was unable to produce fresh
anchors an re-used the existing one a way to often.
UBIFS:
- Fixes for endianness. A few places blindly assumed little endian.
- Fix for a memory leak in the orphan code.
- Fix for a possible crash during a commit.
- Revert a wrong bugfix.
JFFS2:
- Revert a bad bugfix (false positive from a code checking tool)"
* tag 'upstream-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
Revert "jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()"
ubi: Fix producing anchor PEBs
ubifs: ubifs_tnc_start_commit: Fix OOB in layout_in_gaps
ubifs: do_kill_orphans: Fix a memory leak bug
Revert "ubifs: Fix memory leak bug in alloc_ubifs_info() error path"
ubifs: Fix type of sup->hash_algo
ubifs: Fixed missed le64_to_cpu() in journal
ubifs: Force prandom result to __le32
ubifs: Remove obsolete TODO from dfs_file_write()
ubi: Fix warning static is not at beginning of declaration
ubi: Print skip_check in ubi_dump_vol_info()
|
|
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
|
|
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a new fastmap is about to be written UBI must make sure it has a
free block for a fastmap anchor available. For this ubi_update_fastmap()
calls ubi_ensure_anchor_pebs(). This stopped working with 2e8f08deabbc
("ubi: Fix races around ubi_refill_pools()"), with this commit the wear
leveling code is blocked and can no longer produce free PEBs. UBI then
more often than not falls back to write the new fastmap anchor to the
same block it was already on which means the same erase block gets
erased during each fastmap write and wears out quite fast.
As the locking prevents us from producing the anchor PEB when we
actually need it, this patch changes the strategy for creating the
anchor PEB. We no longer create it on demand right before we want to
write a fastmap, but instead we create an anchor PEB right after we have
written a fastmap. This gives us enough time to produce a new anchor PEB
before it is needed. To make sure we have an anchor PEB for the very
first fastmap write we call ubi_ensure_anchor_pebs() during
initialisation as well.
Fixes: 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Compiler generates following warning when kernel is built with W=1:
drivers/mtd/ubi/ubi.h:971:1: warning: ‘static’ is not at beginning
of declaration [-Wold-style-declaration]
This commit fixes this by correctly ordering keywords.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Weinberger <richard@nod.at>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
|
|
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
|
|
CFI core changes:
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
|
|
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1
00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15
00000010
Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
https://github.com/riscv/riscv-linux/commit/c94e267766d62bc9a669611c3d0c8ed5ea26569b
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a10362d ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
|
Esben Haabendal
Michael Walle
Vignesh Raghavendra
Hou Tao
YueHaibing
Sascha Hauer
Mika Westerberg
John Garry
Joseph Kust
Tudor Ambarus
Arnd Bergmann
Peter Ujfalusi
Krzysztof Kozlowski
Amir Mahdi Ghorbanian
Vasyl Gomonovych
Christophe Kerello
Christoph Hellwig
David Bauer
Jerome Brunet
Jungseung Lee
Robert Marko
Linus Torvalds
Sudip Mukherjee
Rishi Gupta
Stefan Roese
Miquel Raynal
Angelo Dureghello
Greg Kroah-Hartman
Sagar Shrikant Kadam
Manivannan Sadhasivam