| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.
This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.
Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode")
Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com>
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: Max Staudt <max@enpas.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org # 6.0.x
[mkl: patch pch_can, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_restart() expects CMD_START_CHIP to set the error state to
ERROR_ACTIVE as it calls netif_carrier_on() immediately afterwards.
Otherwise the user may immediately trigger restart again and hit a
BUG_ON() in can_restart().
Fix kvaser_usb_leaf set_mode(CMD_START_CHIP) to set the expected state.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TX queue seems to be implicitly flushed by the hardware during
bus-off or bus-off recovery, but the driver does not reset the TX
bookkeeping.
Despite not resetting TX bookkeeping the driver still re-enables TX
queue unconditionally, leading to "cannot find free context" /
NETDEV_TX_BUSY errors if the TX queue was full at bus-off time.
Fix that by resetting TX bookkeeping on CAN restart.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
flush_comp is initialized when CMD_FLUSH_QUEUE is sent to the device and
completed when the device sends CMD_FLUSH_QUEUE_RESP.
This causes completion of uninitialized completion if the device sends
CMD_FLUSH_QUEUE_RESP before CMD_FLUSH_QUEUE is ever sent (e.g. as a
response to a flush by a previously bound driver, or a misbehaving
device).
Fix that by initializing flush_comp in kvaser_usb_init_one() like the
other completions.
This issue is only triggerable after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
For command events read from the device,
kvaser_usb_leaf_read_bulk_callback() verifies that cmd->len does not
exceed the size of the received data, but the actual kvaser_cmd handlers
will happily read any kvaser_cmd fields without checking for cmd->len.
This can cause an overread if the last cmd in the buffer is shorter than
expected for the command type (with cmd->len showing the actual short
size).
Maximum overread seems to be 22 bytes (CMD_LEAF_LOG_MESSAGE), some of
which are delivered to userspace as-is.
Fix that by verifying the length of command before handling it.
This issue can only occur after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DMA allocated buffers are a precious resource. If there is no need for
DMA allocations, then it might be worth to use non-dma allocated
buffers.
After testing the gs_usb driver with and without DMA allocation, there
does not seem to be a significant change in latency or CPU utilization
either way. Therefore, DMA allocation is not necessary and removed.
Internal buffers used within urbs were managed and freed manually.
These buffers are no longer needed to be managed by the driver. The
URB_FREE_BUFFER flag, allows for the buffers in question to be
automatically freed.
Co-developed-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Vasanth Sadhasivan <vasanth.sadhasivan@samsara.com>
Link: https://lore.kernel.org/all/20220920154724.861093-2-rhett.aultman@samsara.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The candleLight community is working on switchable termination support
for the candleLight firmware. As the the Linux CAN framework supports
switchable termination add this feature to the gs_usb driver.
Devices supporting the feature should set the
GS_CAN_FEATURE_TERMINATION and implement the
GS_USB_BREQ_SET_TERMINATION and GS_USB_BREQ_GET_TERMINATION control
messages.
For now the driver assumes for activated termination the standard
termination value of 120Ω.
Link: https://lore.kernel.org/all/20220923074114.662045-1-mkl@pengutronix.de
Link: https://github.com/candle-usb/candleLight_fw/issues/92
Link: https://github.com/candle-usb/candleLight_fw/pull/109
Link: https://github.com/candle-usb/candleLight_fw/pull/108
Cc: Daniel Trevitz <daniel.trevitz@wika.com>
Cc: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Introduce a label to free the allocated candev in case of an error and
make use of if. Fix a memory leak if the extended bit timing cannot be
read. Extend the error messages to print the number of the failing
channel and the symbolic error name.
Link: https://lore.kernel.org/all/20220921193902.575416-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Convert the driver to use usb_control_msg_{send,recv}() instead of
usb_control_msg(). These functions allow the data to be placed on the
stack. This makes the driver a lot easier as we don't have to deal
with dynamically allocated memory.
Link: https://lore.kernel.org/all/20220921193902.575416-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Most of the driver uses the variable "dev" to point to the struct
gs_can. Use the same name in gs_cmd_reset(), too. Rename gsdev to dev.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220921193902.575416-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On busy networks the CAN controller might receive CAN frames directly
after starting it but before the timecounter is setup. This will lead
to NULL pointer deref while converting the converting the CAN frame's
timestamp with the timecounter.
Close the race window by setting up the timecounter before starting
the CAN controller.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220921081329.385509-1-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The struct timecounter::cycle_last is a 64 bit variable, read by
timecounter_cyc2time(), and written by timecounter_read(). On 32 bit
architectures this is not atomic.
Add a spinlock to protect access to struct timecounter::cycle_last. In
the gs_usb_timestamp_read() callback the lock is dropped to execute a
sleeping synchronous USB transfer. This is safe, as the variable we
want to protect is accessed during this call.
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-3-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The 2nd argument of usb_control_msg_recv() is the "endpoint",
usb_control_msg_recv() will internally convert the endpoint into a
pipe with usb_rcvctrlpipe().
In gs_usb_get_timestamp() not the endpoint "0" is passed, but the
pipe. This worked by accident as endpoint is a __u8 and the lowest 8
bits of the pipe are 0. Fix this copy/paste error by using the correct
endpoint of "0".
Fixes: 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-2-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Until commit 409c188c57cd ("can: tree-wide: advertise software
timestamping capabilities") the ethtool_ops was only assigned for
devices which support the GS_CAN_FEATURE_IDENTIFY feature. That commit
assigns ethtool_ops unconditionally.
This results on controllers without GS_CAN_FEATURE_IDENTIFY support
for the following ethtool error:
| $ ethtool -p can0 1
| Cannot identify NIC: Broken pipe
Restore the correct error value by checking for
GS_CAN_FEATURE_IDENTIFY in the gs_usb_set_phys_id() function.
| $ ethtool -p can0 1
| Cannot identify NIC: Operation not supported
While there use the variable "netdev" for the "struct net_device"
pointer and "dev" for the "struct gs_can" pointer as in the rest of
the driver.
Fixes: 409c188c57cd ("can: tree-wide: advertise software timestamping capabilities")
Link: http://lore.kernel.org/all/20220818143853.2671854-1-mkl@pengutronix.de
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The dev->can.state is set to CAN_STATE_ERROR_ACTIVE, after the device
has been started. On busy networks the CAN controller might receive
CAN frame between and go into an error state before the dev->can.state
is assigned.
Assign dev->can.state before starting the controller to close the race
window.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220920195216.232481-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Zero-length arrays are deprecated and we are moving towards adopting
C99 flexible-array members, instead. So, replace zero-length array
declaration in union es58x_urb_cmd with the new DECLARE_FLEX_ARRAY()
helper macro.
This helper allows for a flexible-array member in a union.
Link: https://github.com/KSPP/linux/issues/193
Link: https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/all/Yw00w6XRcq7B6ub6@work
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for hardware timestamps, if the firmware includes it as a
feature via the GS_CAN_FEATURE_HW_TIMESTAMP flag. Check for this
feature during probe, extend the RX expected length if it is and
enable it during open.
The struct classic_can_ts and struct canfd_ts are extended to include
the µs timestamp following data as defined in the firmware. The
timestamp is then captured and set using skb_hwtstamps() on each RX
and TX.
The frame µs timestamp is provided from a 32 bit 1 MHz timer which
rolls over every 4294 seconds, so a cyclecounter, timecounter, and
delayed worker are used to convert the timer into a proper ns
timestamp - same implementation as commit efd8d98dfb900 ("can:
mcp251xfd: add HW timestamp infrastructure").
Hardware timestamps are added to capabilities as commit
b1f6b93e678f ("can: mcp251xfd: advertise timestamping capabilities and
add ioctl support").
Signed-off-by: John Whittington <git@jbrengineering.co.uk>
Link: https://github.com/candle-usb/candleLight_fw/issues/100
Link: https://lore.kernel.org/all/20220827221548.3291393-3-mkl@pengutronix.de
Co-developed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There are a few macros in the driver which use GSUSB in the name of
the macro, while the majority uses GS_USB. Convert all macros to
GS_USB.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Fixes: b00ca070e022 ("can: gs_usb: activate quirks for CANtact Pro unconditionally")
Link: https://lore.kernel.org/all/20220827221548.3291393-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use kzalloc(...) rather than kcalloc(1, ...) since because the number of
elements we are specifying in this case is 1, kzalloc would accomplish the
same thing and we can simplify. Also refactor how we calculate the sizeof()
as checkstyle for kzalloc() prefers using the variable we are assigning
to versus the type of that variable for calculating the size to allocate.
Signed-off-by: Kenneth Lee <klee33@uw.edu>
Link: https://lore.kernel.org/all/20220807051656.1991446-1-klee33@uw.edu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220830201457.7984-1-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clang emits a -Wunaligned-access warning on struct __packed
ems_cpc_msg.
The reason is that the anonymous union msg (not declared as packed) is
being packed right after some non naturally aligned variables (3*8
bits + 2*32) inside a packed struct:
| struct __packed ems_cpc_msg {
| u8 type; /* type of message */
| u8 length; /* length of data within union 'msg' */
| u8 msgid; /* confirmation handle */
| __le32 ts_sec; /* timestamp in seconds */
| __le32 ts_nsec; /* timestamp in nano seconds */
| /* ^ not naturally aligned */
|
| union {
| /* ^ not declared as packed */
| u8 generic[64];
| struct cpc_can_msg can_msg;
| struct cpc_can_params can_params;
| struct cpc_confirm confirmation;
| struct cpc_overrun overrun;
| struct cpc_can_error error;
| struct cpc_can_err_counter err_counter;
| u8 can_state;
| } msg;
| };
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
Fix the warning by marking the anonymous union as packed.
[1] https://github.com/llvm/llvm-project/issues/55520
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/all/20220802094021.959858-1-mkl@pengutronix.de
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Aside of urb->transfer_buffer_length and urb->context which might
change in the TX path, all the other URB parameters remains constant
during runtime. So, there is no reasons to call usb_fill_bulk_urb()
each time before submitting an URB.
Make sure to initialize all the fields of the URB at allocation
time. For the TX branch, replace the call usb_fill_bulk_urb() by an
assignment of urb->context. urb->urb->transfer_buffer_length is
already set by the caller functions, no need to set it again. For the
RX branch, because all parameters are unchanged, simply remove the
call to usb_fill_bulk_urb().
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220729080902.25839-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, userland has no method to query which timestamping features
are supported by the peak_usb driver (aside maybe of getting RX
messages and observe whether or not hardware timestamps stay at zero).
The canonical way to add hardware timestamp support is to implement
ethtool_ops::get_ts_info() in order to advertise the timestamping
capabilities and to implement net_device_ops::ndo_eth_ioctl() as
requested in [1]. Currently, the driver only supports hardware RX
timestamps [2] but not hardware TX. For this reason, the generic
function can_ethtool_op_get_ts_info_hwts() and can_eth_ioctl_hwts()
can not be reused and instead this patch adds pcan_get_ts_info() and
peak_eth_ioctl().
[1] kernel doc Timestamping, section 3.1: "Hardware Timestamping
Implementation: Device Drivers"
Link: https://docs.kernel.org/networking/timestamping.html#hardware-timestamping-implementation-device-drivers
[2] https://lore.kernel.org/linux-can/20220727080634.l6uttnbrmwbabh3o@pengutronix.de/
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-15-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, userland has no method to query which timestamping features
are supported by the kvaser_usb driver (aside maybe of getting RX
messages and observe whether or not hardware timestamps stay at zero).
The canonical way for a network driver to advertise what kind of
timestamping it supports is to implement
ethtool_ops::get_ts_info(). Here, we use the CAN specific
can_ethtool_op_get_ts_info_hwts() function to achieve this.
In addition, the driver currently does not support the hardware
timestamps ioctls. According to [1], SIOCSHWTSTAMP is "must" and
SIOCGHWTSTAMP is "should". This patch fills up that gap by
implementing net_device_ops::ndo_eth_ioctl() using the CAN specific
function can_eth_ioctl_hwts().
[1] kernel doc Timestamping, section 3.1: "Hardware Timestamping
Implementation: Device Drivers"
Link: https://docs.kernel.org/networking/timestamping.html#hardware-timestamping-implementation-device-drivers
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-13-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, userland has no method to query which timestamping features
are supported by the etas_es58x driver (aside maybe of getting RX
messages and observe whether or not hardware timestamps stay at zero).
The canonical way for a network driver to advertise what kind of
timestamping is supports is to implement
ethtool_ops::get_ts_info(). Here, we use the CAN specific
can_ethtool_op_get_ts_info_hwts() function to achieve this.
In addition, the driver currently does not support the hardware
timestamps ioctls. According to [1], SIOCSHWTSTAMP is "must" and
SIOCGHWTSTAMP is "should". This patch fills up that gap by
implementing net_device_ops::ndo_eth_ioctl() using the CAN specific
function can_eth_ioctl_hwts().
[1] kernel doc Timestamping, section 3.1: "Hardware Timestamping
Implementation: Device Drivers"
Link: https://docs.kernel.org/networking/timestamping.html#hardware-timestamping-implementation-device-drivers
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-11-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently, some CAN drivers support hardware timestamping, some do
not. But userland has no method to query which features are supported
(aside maybe of getting RX messages and observe whether or not
hardware timestamps stay at zero).
The canonical way for a network driver to advertised what kind of
timestamping it supports is to implement ethtool_ops::get_ts_info().
This patch only targets the CAN drivers which *do not* support
hardware timestamping. For each of those CAN drivers, implement the
get_ts_info() using the generic ethtool_op_get_ts_info().
This way, userland can do:
| $ ethtool --show-time-stamping canX
to confirm the device timestamping capacities.
N.B. the drivers which support hardware timestamping will be migrated
in separate patches.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr
[mkl: mscan: add missing mscan_ethtool_ops]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
DRV_VERSION is a leftover from when the driver was an out of tree
module. The driver version was never incremented despite of the
numerous changes made since it was mainstreamed. Keeping an
unmaintained driver version number makes no sense. Remove it and rely
on the kernel version instead.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-11-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
ES58X_MODULE_NAME is set to "etas_es58x". KBUILD_MODNAME also
evaluates to "etas_es58x". Get rid of ES58X_MODULE_NAME and rely on
KBUILD_MODNAME instead.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-10-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses the string "usb_8dev" to populate usb_driver::name and
can_bittiming_const::name. KBUILD_MODNAME also evaluates to
"ubs_8dev". Use KBUILD_MODNAME and get rid on the hardcoded string
names.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-9-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses the string "kvaser_usb" to populate
usb_driver::name. KBUILD_MODNAME also evaluates to "kvaser_ubs". Use
KBUILD_MODNAME and get rid on the hardcoded string names.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses the string "gs_usb" to populate usb_driver::name,
can_bittiming_const::name and
can_data_bittiming_const::name. KBUILD_MODNAME evaluates to
"gs_ubs". Use KBUILD_MODNAME and get rid on the hardcoded string
names.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses the string "ems_usb" to populate
usb_driver::name. KBUILD_MODNAME also evaluates to "esd_ubs". Use
KBUILD_MODNAME and get rid on the hardcoded string names.
CC: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses the string "ems_usb" to populate usb_driver::name and
can_bittiming_const::name. KBUILD_MODNAME also evaluates to
"ems_ubs". Use KBUILD_MODNAME and get rid on the hardcoded string
names.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220726082707.58758-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a dedicated flag in uapi/linux/can/error.h to notify the userland
that fields data[6] and data[7] of the CAN error frame were
respectively populated with the tx and rx error counters.
For all driver tree-wide, set up this flags whenever needed.
Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220719143550.3681-10-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 7259124eac7d1 ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Link: https://lore.kernel.org/all/20220719143550.3681-9-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Link: https://lore.kernel.org/all/20220719143550.3681-8-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CANFD-USB PCAN-USB FD interface undergoes an internal component
change that requires a slight modification of its drivers, which leads
them to dynamically use endpoint numbers provided by the interface
itself. In addition to a change in the calls to the USB functions
exported by the kernel, the detection of the USB interface dedicated
to CAN must also be modified, as some PEAK-System devices support
other interfaces than CAN.
Link: https://lore.kernel.org/all/20220719120632.26774-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: add missing cpu_to_le16() conversion]
[mkl: fix networking block comment style]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The data structure returned from the USB device contains a number
flashed by the user and not the serial number of the device.
Link: https://lore.kernel.org/all/20220719120632.26774-2-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Mark the input prompt and data pointer as const.
Link: https://lore.kernel.org/all/20220719120632.26774-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: mark data pointer as const, too; update commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: b4f20130af23 ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe")
Fixes: f5d4abea3ce0 ("can: kvaser_usb: Add support for the USBcan-II family")
Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.
This regression affects M32C based Leaf devices with non-16MHz clock.
Fixes: fb12797ab1fe ("can: kvaser_usb: get CAN clock frequency from device")
Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.
All Kvaser USBcanII supports listen-only mode and error counter
reporting.
Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad41b ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
- Brought the copyright notice up to date
- Also regarding the changed company name from
esd electronic system design gmbh to esd electronics gmbh
- Using socketcan@esd.eu as a generic mail address for matthias who
left esd 6 years before
- Added a second MODULE_AUTHOR() for Frank Jungclaus
Link: https://lore.kernel.org/all/20220624190517.2299701-6-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Link: https://lore.kernel.org/all/20220624190517.2299701-5-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Each occurrence of the term "usb2" within variables, function names,
comments, etc. is changed to "usb" where it is shared for all
esd CAN/USB devices.
Link: https://lore.kernel.org/all/20220624190517.2299701-4-frank.jungclaus@esd.eu
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
Oliver Hartkopp
Anssi Hannula
Vasanth Sadhasivan
Marc Kleine-Budde
Jakub Kicinski
Gustavo A. R. Silva
John Whittington
Kenneth Lee
Wolfram Sang
Vincent Mailhol
Stephane Grosjean
Jimmy Assarsson
Rhett Aultman
Frank Jungclaus