| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Moves the drivers for the Chelsio chipsets into
drivers/net/ethernet/chelsio/ and the necessary Kconfig and Makefile
changes.
CC: Divy Le Ray <divy@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T3 hardware doorbell FIFO overflows can cause application stalls due
to lost doorbell ring events. This has been seen when running large
NP IMB alltoall MPI jobs. The T3 hardware supports an xon/xoff-type
flow control mechanism to help avoid overflowing the HW doorbell FIFO.
This patch uses these interrupts to disable RDMA QP doorbell rings
when we near an overflow condition, and then turn them back on (and
ring all the active QP doorbells) when when the doorbell FIFO empties
out. In addition if an doorbell ring is dropped by the hardware, the
code will now recover.
Design:
cxgb3:
- enable these DB interrupts
- in the interrupt handler, schedule work tasks to call the ULPs event
handlers with the new events.
- ring all the qset txqs when an overflow is detected.
iw_cxgb3:
- disable db ringing on all active qps when we get the DB_FULL event
- enable db ringing on all active qps and ring all active dbs when we get
the DB_EMPTY event
- On DB_DROP event:
- disable db rings in the event handler
- delay-schedule a work task which rings and enables the dbs on
all active qps.
- in post_send and post_recv logic, don't ring the db if it's disabled.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
The driver currently ignores the local or remote link faults
raised at the mac layer. This patch fixes it.
Our mac however only advertizes link events, so wait for the
phy to stabilize the link, then enable mac link events interrupts.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under RX pressure, The HW might generate a high load of interrupts
to signal mac fifo or free lists overflow.
Disable the interrupts, and poll the relevant status bits
to maintain stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not require PHY interrupts to be connected to GPIs in ascending order.
Base interrupt availability both on PHYs supporting them and on GPIs being
hooked up. Allows boards to specify interrupt GPIs though the PHYs don't
use them.
Remove spurious PHY interrupts due to clearing T3DBG interrupts before
setting their polarity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add iSCSI (S3xx) support.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Reset the chip when the PCI link goes down.
Preserve the napi structure when a sge qset's resources are freed.
Replay only HW initialization when the chip comes out of reset.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add parity initialization for T3C adapters.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Disable PEX errors. The HW generates false positives.
Update RSS hash function to a symmetric algorithm.
Update T3C HW support
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Set PM1 internal memory to round robin mode
It balances access to this internal memory for multiport adapters.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Log doorbell Fifo overflow
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The chip executes microcode present in internal RAM,
whose content is loaded from EEPROM on power cycle.
This patch allows an update of the microcode through PIO
without forcing a power cycle.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update FW to 4.1.
Proceed to subsequent HW tuning to improve RDMA perfs..
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Rx traffic needs to be halted when the MTU is changed
to avoid a potential chip hang.
Reset/restore MAC filters around a MTU change.
Also fix the pause frames high materwark setting.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Check all lanes for link status on direct XAUI cards.
Don't assume that direct XAUI always uses XGMAC 1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Under rare conditions, the MAC might hang while generating a pause frame.
This patch fine tunes the MAC settings to avoid the issue, allows for
periodic MAC state check, and triggers a recovery if hung.
Also fix one MAC statistics counter for the rev board T3B2.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
Jeff Kirsher
Casey Leedom
Steve Wise
Divy Le Ray
Karen Xie