aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/amd/xgbe (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-10-21amd-xgbe: add the bit rate quirk for Molex cablesRaju Rangoju1-1/+8
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex passive cables have the rate ceiling 0x78 at offset 12. Add a quirk for Molex passive cables to extend the rate ceiling to 0x78. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-21amd-xgbe: fix the SFP compliance codes check for DAC cablesRaju Rangoju1-4/+4
The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive) cables is NULL. However, some cables (the 5 meter and 7 meter Molex passive cables) have non-zero data at offset 6. Fix the logic by moving the passive cable check above the active checks, so as not to be improperly identified as an active cable. This will fix the issue for any passive cable that advertises 1000Base-CX in offset 6. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-21amd-xgbe: enable PLL_CTL for fixed PHY modes onlyRaju Rangoju1-2/+8
PLL control setting(RRC) is needed only in fixed PHY configuration to fix the peer-peer issues. Without the PLL control setting, the link up takes longer time in a fixed phy configuration. Driver implements SW RRC for Autoneg On configuration, hence PLL control setting (RRC) is not needed for AN On configuration, and can be skipped. Also, PLL re-initialization is not needed for PHY Power Off and RRC commands. Otherwise, they lead to mailbox errors. Added the changes accordingly. Fixes: daf182d360e5 ("net: amd-xgbe: Toggle PLL settings during rate change") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-21amd-xgbe: use enums for mailbox cmd and sub_cmdsRaju Rangoju2-13/+41
Instead of using hardcoded values, use enumerations for mailbox command and sub commands. Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-21amd-xgbe: Yellow carp devices do not need rrcRaju Rangoju3-1/+7
Link stability issues are noticed on Yellow carp platforms when Receiver Reset Cycle is issued. Since the CDR workaround is disabled on these platforms, the Receiver Reset Cycle is not needed. So, avoid issuing rrc on Yellow carp platforms. Fixes: dbb6c58b5a61 ("net: amd-xgbe: Add Support for Yellow Carp Ethernet device") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-28net: drop the weight argument from netif_napi_addJakub Kicinski1-2/+2
We tell driver developers to always pass NAPI_POLL_WEIGHT as the weight to netif_napi_add(). This may be confusing to newcomers, drop the weight argument, those who really need to tweak the weight can use netif_napi_add_weight(). Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-08-31net: ethernet: move from strlcpy with unused retval to strscpyWolfram Sang1-2/+2
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2 Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5} Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-07-11amd-xgbe: fix clang -Wformat warningsJustin Stitt1-1/+1
When building with Clang we encounter the following warning: | drivers/net/ethernet/amd/xgbe/xgbe-dcb.c:234:42: error: format specifies | type 'unsigned char' but the argument has type '__u16' (aka 'unsigned | short') [-Werror,-Wformat] pfc->pfc_cap, pfc->pfc_en, pfc->mbc, | pfc->delay); pfc->pfc_cap , pfc->pfc_cn, pfc->mbc are all of type `u8` while pfc->delay is of type `u16`. The correct format specifiers `%hh[u|x]` were used for the first three but not for pfc->delay, which is causing the warning above. Variadic functions (printf-like) undergo default argument promotion. Documentation/core-api/printk-formats.rst specifically recommends using the promoted-to-type's format flag. In this case `%d` (or `%x` to maintain hex representation) should be used since both u8's and u16's are fully representable by an int. Moreover, C11 6.3.1.1 states: (https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf) `If an int can represent all values of the original type ..., the value is converted to an int; otherwise, it is converted to an unsigned int. These are called the integer promotions.` Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Justin Stitt <justinstitt@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20220708232653.556488-1-justinstitt@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-07-02net: add skb_[inner_]tcp_all_headers helpersEric Dumazet1-4/+2
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)" to compute headers length for a TCP packet, but others use more convoluted (but equivalent) ways. Add skb_tcp_all_headers() and skb_inner_tcp_all_headers() helpers to harmonize this a bit. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-27amd/xgbe: fix repeated words in commentsJilin Yuan1-1/+1
Delete the redundant word 'use'. Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com> Link: https://lore.kernel.org/r/20220625070633.64982-1-yuanjilin@cdjrlc.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-13amd-xgbe: Use platform_irq_count()Jean-Philippe Brucker1-2/+2
The AMD XGbE driver currently counts the number of interrupts assigned to the device by inspecting the pdev->resource array. Since commit a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT core") removed IRQs from this array, the driver now attempts to get all interrupts from 1 to -1U and gives up probing once it reaches an invalid interrupt index. Obtain the number of IRQs with platform_irq_count() instead. Fixes: a1a2b7125e10 ("of/platform: Drop static setup of IRQ resource from DT core") Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lore.kernel.org/r/20220609161457.69614-1-jean-philippe@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-08net: amd-xgbe: fix clang -Wformat warningJustin Stitt1-1/+1
see warning: | drivers/net/ethernet/amd/xgbe/xgbe-drv.c:2787:43: warning: format specifies | type 'unsigned short' but the argument has type 'int' [-Wformat] | netdev_dbg(netdev, "Protocol: %#06hx\n", ntohs(eth->h_proto)); | ~~~~~~ ^~~~~~~~~~~~~~~~~~~ Variadic functions (printf-like) undergo default argument promotion. Documentation/core-api/printk-formats.rst specifically recommends using the promoted-to-type's format flag. Also, as per C11 6.3.1.1: (https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf) `If an int can represent all values of the original type ..., the value is converted to an int; otherwise, it is converted to an unsigned int. These are called the integer promotions.` Since the argument is a u16 it will get promoted to an int and thus it is most accurate to use the %x format specifier here. It should be noted that the `#06` formatting sugar does not alter the promotion rules. Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Justin Stitt <jstitt007@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20220607191119.20686-1-jstitt007@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-16net: allow gso_max_size to exceed 65536Alexander Duyck1-1/+2
The code for gso_max_size was added originally to allow for debugging and workaround of buggy devices that couldn't support TSO with blocks 64K in size. The original reason for limiting it to 64K was because that was the existing limits of IPv4 and non-jumbogram IPv6 length fields. With the addition of Big TCP we can remove this limit and allow the value to potentially go up to UINT_MAX and instead be limited by the tso_max_size value. So in order to support this we need to go through and clean up the remaining users of the gso_max_size value so that the values will cap at 64K for non-TCPv6 flows. In addition we can clean up the GSO_MAX_SIZE value so that 64K becomes GSO_LEGACY_MAX_SIZE and UINT_MAX will now be the upper limit for GSO_MAX_SIZE. v6: (edumazet) fixed a compile error if CONFIG_IPV6=n, in a new sk_trim_gso_size() helper. netif_set_tso_max_size() caps the requested TSO size with GSO_MAX_SIZE. Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-09net: amd-xgbe: disable interrupts during pci removalRaju Rangoju1-0/+3
Hardware interrupts are enabled during the pci probe, however, they are not disabled during pci removal. Disable all hardware interrupts during pci removal to avoid any issues. Fixes: e75377404726 ("amd-xgbe: Update PCI support to use new IRQ functions") Suggested-by: Selwin Sebastian <Selwin.Sebastian@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-27net: amd-xgbe: ensure to reset the tx_timer_active flagRaju Rangoju1-0/+2
Ensure to reset the tx_timer_active flag in xgbe_stop(), otherwise a port restart may result in tx timeout due to uncleared flag. Fixes: c635eaacbf77 ("amd-xgbe: Remove Tx coalescing") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lore.kernel.org/r/20220127060222.453371-1-Raju.Rangoju@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-27net: amd-xgbe: Fix skb data length underflowShyam Sundar S K1-1/+11
There will be BUG_ON() triggered in include/linux/skbuff.h leading to intermittent kernel panic, when the skb length underflow is detected. Fix this by dropping the packet if such length underflows are seen because of inconsistencies in the hardware descriptors. Fixes: 622c36f143fc ("amd-xgbe: Fix jumbo MTU processing on newer hardware") Suggested-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lore.kernel.org/r/20220127092003.2812745-1-Shyam-sundar.S-k@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20net: amd-xgbe: Disable the CDR workaround path for Yellow Carp DevicesRaju Rangoju1-2/+5
Yellow Carp Ethernet devices do not require Autonegotiation CDR workaround, hence disable the same. Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20net: amd-xgbe: Alter the port speed bit rangeRaju Rangoju2-6/+6
Newer generation Hardware uses the slightly different port speed bit widths, so alter the existing port speed bit range to extend support to the newer generation hardware while maintaining the backward compatibility with older generation hardware. The previously reserved bits are now being used which then requires the adjustment to the BIT values, e.g.: Before: PORT_PROPERTY_0[22:21] - Reserved PORT_PROPERTY_0[26:23] - Supported Speeds After: PORT_PROPERTY_0[21] - Reserved PORT_PROPERTY_0[26:22] - Supported Speeds To make this backwards compatible, the existing BIT definitions for the port speeds are incremented by one to maintain the original position. Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-20net: amd-xgbe: Add Support for Yellow Carp Ethernet deviceRaju Rangoju2-0/+6
Yellow Carp Ethernet devices use the existing PCI ID but the window settings for the indirect PCS access have been altered. Add the check for Yellow Carp Ethernet devices to use the new register values. Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-14net_tstamp: add new flag HWTSTAMP_FLAG_BONDED_PHC_INDEXHangbin Liu1-3/+0
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device") the user could get bond active interface's PHC index directly. But when there is a failover, the bond active interface will change, thus the PHC index is also changed. This may break the user's program if they did not update the PHC timely. This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX. When the user wants to get the bond active interface's PHC, they need to add this flag and be aware the PHC index may be changed. With the new flag. All flag checks in current drivers are removed. Only the checking in net_hwtstamp_validate() is kept. Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: extend ringparam setting/getting API with rx_buf_lenHao Chen1-3/+8
Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2-1/+27
Merge in the fixes we had queued in case there was another -rc. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-29net: amd-xgbe: Toggle PLL settings during rate changeShyam Sundar S K2-1/+27
For each rate change command submission, the FW has to do a phy power off sequence internally. For this to happen correctly, the PLL re-initialization control setting has to be turned off before sending mailbox commands and re-enabled once the command submission is complete. Without the PLL control setting, the link up takes longer time in a fixed phy configuration. Fixes: 47f164deab22 ("amd-xgbe: Add PCI device support") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson1-5/+3
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-14ethernet: constify references to netdev->dev_addr in driversJakub Kicinski2-2/+2
This big patch sprinkles const on local variables and function arguments which may refer to netdev->dev_addr. Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Some of the changes here are not strictly required - const is sometimes cast off but pointer is not used for writing. It seems like it's still better to add the const in case the code changes later or relevant -W flags get enabled for the build. No functional changes. Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-10ethernet: Remove redundant 'flush_workqueue()' callsChristophe JAILLET1-2/+0
'destroy_workqueue()' already drains the queue before destroying it, so there is no need to flush it explicitly. Remove the redundant 'flush_workqueue()' calls. This was generated with coccinelle: @@ expression E; @@ - flush_workqueue(E); destroy_workqueue(E); Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx* Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05ethernet: use eth_hw_addr_set() for dev->addr_len casesJakub Kicinski2-2/+2
Convert all Ethernet drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) In theory addr_len may not be ETH_ALEN, but we don't expect non-Ethernet devices to live under this directory, and only the following cases of setting addr_len exist: - cxgb4 for mgmt device, and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-24ethtool: extend coalesce setting uAPI with CQE modeYufeng Mo1-2/+6
In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-07-27dev_ioctl: split out ndo_eth_ioctlArnd Bergmann1-1/+1
Most users of ndo_do_ioctl are ethernet drivers that implement the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP. Separate these from the few drivers that use ndo_do_ioctl to implement SIOCBOND, SIOCBR and SIOCWANDEV commands. This is a purely cosmetic change intended to help readers find their way through the implementation. Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Leon Romanovsky <leon@kernel.org> Cc: linux-rdma@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25amd-xgbe: Update DMA coherency valuesShyam Sundar S K1-3/+3
Based on the IOMMU configuration, the current cache control settings can result in possible coherency issues. The hardware team has recommended new settings for the PCI device path to eliminate the issue. Fixes: 6f595959c095 ("amd-xgbe: Adjust register settings to improve performance") Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller4-3/+54
2021-02-16net: amd-xgbe: Fix network fluctuations when using 1G BELFUSE SFPShyam Sundar S K1-0/+3
Frequent link up/down events can happen when a Bel Fuse SFP part is connected to the amd-xgbe device. Try to avoid the frequent link issues by resetting the PHY as documented in Bel Fuse SFP datasheets. Fixes: e722ec82374b ("amd-xgbe: Update the BelFuse quirk to support SGMII") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16net: amd-xgbe: Reset link when the link never comes backShyam Sundar S K2-1/+9
Normally, auto negotiation and reconnect should be automatically done by the hardware. But there seems to be an issue where auto negotiation has to be restarted manually. This happens because of link training and so even though still connected to the partner the link never "comes back". This needs an auto-negotiation restart. Also, a change in xgbe-mdio is needed to get ethtool to recognize the link down and get the link change message. This change is only required in a backplane connection mode. Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16net: amd-xgbe: Fix NETDEV WATCHDOG transmit queue timeout warningShyam Sundar S K2-1/+1
The current driver calls netif_carrier_off() late in the link tear down which can result in a netdev watchdog timeout. Calling netif_carrier_off() immediately after netif_tx_stop_all_queues() avoids the warning. ------------[ cut here ]------------ NETDEV WATCHDOG: enp3s0f2 (amd-xgbe): transmit queue 0 timed out WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x20d/0x220 Modules linked in: amd_xgbe(E) amd-xgbe 0000:03:00.2 enp3s0f2: Link is Down CPU: 3 PID: 0 Comm: swapper/3 Tainted: G E Hardware name: AMD Bilby-RV2/Bilby-RV2, BIOS RBB1202A 10/18/2019 RIP: 0010:dev_watchdog+0x20d/0x220 Code: 00 49 63 4e e0 eb 92 4c 89 e7 c6 05 c6 e2 c1 00 01 e8 e7 ce fc ff 89 d9 48 RSP: 0018:ffff90cfc28c3e88 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000006 RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffff90cfc28d63c0 RBP: ffff90cfb977845c R08: 0000000000000050 R09: 0000000000196018 R10: ffff90cfc28c3ef8 R11: 0000000000000000 R12: ffff90cfb9778000 R13: 0000000000000003 R14: ffff90cfb9778480 R15: 0000000000000010 FS: 0000000000000000(0000) GS:ffff90cfc28c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f240ff2d9d0 CR3: 00000001e3e0a000 CR4: 00000000003406e0 Call Trace: <IRQ> ? pfifo_fast_reset+0x100/0x100 call_timer_fn+0x2b/0x130 run_timer_softirq+0x3e8/0x440 ? enqueue_hrtimer+0x39/0x90 Fixes: e722ec82374b ("amd-xgbe: Update the BelFuse quirk to support SGMII") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16net: amd-xgbe: Reset the PHY rx data path when mailbox command timeoutShyam Sundar S K2-1/+41
Sometimes mailbox commands timeout when the RX data path becomes unresponsive. This prevents the submission of new mailbox commands to DXIO. This patch identifies the timeout and resets the RX data path so that the next message can be submitted properly. Fixes: 549b32af9f7c ("amd-xgbe: Simplify mailbox interface rate change code") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-01-07net: remove ndo_udp_tunnel_* callbacksJakub Kicinski1-2/+0
All UDP tunnel port management is now routed via udp_tunnel_nic infra directly. Remove the old callbacks. Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-14net: amd-xgbe: convert tasklets to use new tasklet_setup() APIAllen Pais3-22/+19
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds1-0/+13
Pull networking fixes from David Miller: 1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi Kivilinna. 2) Fix loss of RTT samples in rxrpc, from David Howells. 3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu. 4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka. 5) We disable BH for too lokng in sctp_get_port_local(), add a cond_resched() here as well, from Xin Long. 6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu. 7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from Yonghong Song. 8) Missing of_node_put() in mt7530 DSA driver, from Sumera Priyadarsini. 9) Fix crash in bnxt_fw_reset_task(), from Michael Chan. 10) Fix geneve tunnel checksumming bug in hns3, from Yi Li. 11) Memory leak in rxkad_verify_response, from Dinghao Liu. 12) In tipc, don't use smp_processor_id() in preemptible context. From Tuong Lien. 13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu. 14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter. 15) Fix ABI mismatch between driver and firmware in nfp, from Louis Peens. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits) net/smc: fix sock refcounting in case of termination net/smc: reset sndbuf_desc if freed net/smc: set rx_off for SMCR explicitly net/smc: fix toleration of fake add_link messages tg3: Fix soft lockup when tg3_reset_task() fails. doc: net: dsa: Fix typo in config code sample net: dp83867: Fix WoL SecureOn password nfp: flower: fix ABI mismatch between driver and firmware tipc: fix shutdown() of connectionless socket ipv6: Fix sysctl max for fib_multipath_hash_policy drivers/net/wan/hdlc: Change the default of hard_header_len to 0 net: gemini: Fix another missing clk_disable_unprepare() in probe net: bcmgenet: fix mask check in bcmgenet_validate_flow() amd-xgbe: Add support for new port mode net: usb: dm9601: Add USB ID of Keenetic Plus DSL vhost: fix typo in error message net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init() pktgen: fix error message with wrong function name net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode cxgb4: fix thermal zone device registration ...
2020-09-02amd-xgbe: Add support for new port modeShyam Sundar S K1-0/+13
Add support for a new port mode that is a backplane connection without support for auto negotiation. Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-3/+3
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-07-14xgbe: convert to new udp_tunnel_nic infraJakub Kicinski3-243/+30
Make use of the new udp_tunnel_nic infra. Don't clear the features when VxLAN port is not present to make all drivers behave the same. Driver will now (until we address the problem in the core) leave the RX UDP tunnel feature always on, since this is what most drivers do. Remove the list of VxLAN ports, just program the one core told us to. The driver seem to want to clear the VxLAN ports on close but it doesn't seem to flush the port list properly so it'd get wrong use counts after close/open. Again since it calls its own open handler we need the reset notification hack. v2: - fix kbuild warning Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-14xgbe: switch to more generic VxLAN detectionJakub Kicinski1-19/+8
Instead of looping though the list of ports just check if the geometry of the packet is correct for VxLAN. HW most likely doesn't care about the exact port, anyway, since only first port is actually offloaded, and this way we won't have to maintain the port list at all. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-23amd-xgbe: Convert to generic power managementVaibhav Gupta1-10/+9
Use dev_pm_ops structure to call generic suspend() and resume() callbacks. Drivers should avoid saving device register and/or change power states using PCI helper functions. With the generic approach, all these are handled by PCI core. Compile-tested only. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-16amd-xgbe: Use __napi_schedule() in BH contextSebastian Andrzej Siewior1-1/+1
The driver uses __napi_schedule_irqoff() which is fine as long as it is invoked with disabled interrupts by everybody. Since the commit mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq context. This may lead to list corruption if another driver uses __napi_schedule_irqoff() in IRQ context. Use __napi_schedule() which safe to use from IRQ and softirq context. Fixes: 85b85c853401d ("amd-xgbe: Re-issue interrupt if interrupt status not cleared") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05xgbe: let core reject the unsupported coalescing parametersJakub Kicinski1-24/+2
Set ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters. This driver correctly rejects all unsupported parameters. We are only losing the error print. v3: adjust commit message for new error code and member name Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-24net/amd: Remove useless driver versionLeon Romanovsky3-3/+0
Convert AMD drivers to respect universal linux kernel version. Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-13amd-xgbe: remove unnecessary conversion to boolChen Zhou1-1/+1
The conversion to bool is not needed, remove it. Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2019-12-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-2/+2
Mere overlapping changes in the conflicts here. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin1-1/+1
This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-09treewide: Use sizeof_field() macroPankaj Bharadiya1-2/+2
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except at places where these are defined. Later patches will remove the unused definition of FIELD_SIZEOF(). This patch is generated using following script: EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h" git grep -l -e "\bFIELD_SIZEOF\b" | while read file; do if [[ "$file" =~ $EXCLUDE_FILES ]]; then continue fi sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file; done Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com Co-developed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: David Miller <davem@davemloft.net> # for net
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.