| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
E810 products can support low latency Tx timestamp register read.
This requires usage of threaded IRQ instead of kthread to reduce the
kthread start latency (spikes up to 20 ms).
Add a check for the device capability and use the new method if
supported.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220916201728.241510-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once the E822 device has sent and received one packet, the hardware
computes the internal delay of the PHY using a process known as Vernier
calibration. This calibration calculates a more accurate offset for the
Tx and Rx timestamps. To make use of this offset, we need to exit the
bypass mode. This cannot be done until the PHY has completed offset
calibration, as indicated by the offset valid bits.
To handle this, introduce a kthread work item which will poll the offset
valid bits every few milliseconds seeing if it is safe to exit bypass
mode.
Once we have finished calibrating the offsets, we can program the total
Tx and Rx offset registers and turn off the bypass bit. This allows the
hardware to include the more precise vernier calibration offset, and
improves the timestamp precision.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E822 device has a Clock Generation Unit (CGU) responsible for
determining the clock frequency that drives the timers.
Ensure this function is initialized when bringing up the PTP support, so
that the clock has a known frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When we enable support for E822 devices, there are some additional
steps required to initialize the PTP hardware clock. To make this easier
to implement as device-specific behavior, refactor the register setups
in ice_ptp_init_owner to a new ice_ptp_init_phc function defined in
ice_ptp_hw.c
This function will have a common section, and an e810 specific
sub-implementation.
This will enable easily extending the functionality to cover the E822
specific setup required to initialize the hardware clock generation
unit. It also makes it clear which steps are E810 specific vs which ones
are necessary for all ice devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E810-T adapters have two external bidirectional SMA connectors and two
internal unidirectional U.FL connectors. Multiplexing between U.FL and
SMA and SMA direction is controlled using the PCA9575 expander.
Add support for the PCA9575 detection and control of the respective pins
of the SMA/U.FL multiplexer using the GPIO AQ API.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.
For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.
Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.
The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
Karol Kolacinski
Jacob Keller
Maciej Machnikowski