| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
rhashtable_lookup_fast() internally calls rcu_read_lock() then,
calls rhashtable_lookup(). So if rcu_read_lock() is already held,
rhashtable_lookup() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
92117d8443bc ("bpf: fix refcnt overflow") turned refcounting of bpf_map into
potentially failing operation, when refcount reaches BPF_MAX_REFCNT limit
(32k). Due to using 32-bit counter, it's possible in practice to overflow
refcounter and make it wrap around to 0, causing erroneous map free, while
there are still references to it, causing use-after-free problems.
But having a failing refcounting operations are problematic in some cases. One
example is mmap() interface. After establishing initial memory-mapping, user
is allowed to arbitrarily map/remap/unmap parts of mapped memory, arbitrarily
splitting it into multiple non-contiguous regions. All this happening without
any control from the users of mmap subsystem. Rather mmap subsystem sends
notifications to original creator of memory mapping through open/close
callbacks, which are optionally specified during initial memory mapping
creation. These callbacks are used to maintain accurate refcount for bpf_map
(see next patch in this series). The problem is that open() callback is not
supposed to fail, because memory-mapped resource is set up and properly
referenced. This is posing a problem for using memory-mapping with BPF maps.
One solution to this is to maintain separate refcount for just memory-mappings
and do single bpf_map_inc/bpf_map_put when it goes from/to zero, respectively.
There are similar use cases in current work on tcp-bpf, necessitating extra
counter as well. This seems like a rather unfortunate and ugly solution that
doesn't scale well to various new use cases.
Another approach to solve this is to use non-failing refcount_t type, which
uses 32-bit counter internally, but, once reaching overflow state at UINT_MAX,
stays there. This utlimately causes memory leak, but prevents use after free.
But given refcounting is not the most performance-critical operation with BPF
maps (it's not used from running BPF program code), we can also just switch to
64-bit counter that can't overflow in practice, potentially disadvantaging
32-bit platforms a tiny bit. This simplifies semantics and allows above
described scenarios to not worry about failing refcount increment operation.
In terms of struct bpf_map size, we are still good and use the same amount of
space:
BEFORE (3 cache lines, 8 bytes of padding at the end):
struct bpf_map {
const struct bpf_map_ops * ops __attribute__((__aligned__(64))); /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
int spin_lock_off; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
u32 btf_key_type_id; /* 56 4 */
u32 btf_value_type_id; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct btf * btf; /* 64 8 */
struct bpf_map_memory memory; /* 72 16 */
bool unpriv_array; /* 88 1 */
bool frozen; /* 89 1 */
/* XXX 38 bytes hole, try to pack */
/* --- cacheline 2 boundary (128 bytes) --- */
atomic_t refcnt __attribute__((__aligned__(64))); /* 128 4 */
atomic_t usercnt; /* 132 4 */
struct work_struct work; /* 136 32 */
char name[16]; /* 168 16 */
/* size: 192, cachelines: 3, members: 21 */
/* sum members: 146, holes: 1, sum holes: 38 */
/* padding: 8 */
/* forced alignments: 2, forced holes: 1, sum forced holes: 38 */
} __attribute__((__aligned__(64)));
AFTER (same 3 cache lines, no extra padding now):
struct bpf_map {
const struct bpf_map_ops * ops __attribute__((__aligned__(64))); /* 0 8 */
struct bpf_map * inner_map_meta; /* 8 8 */
void * security; /* 16 8 */
enum bpf_map_type map_type; /* 24 4 */
u32 key_size; /* 28 4 */
u32 value_size; /* 32 4 */
u32 max_entries; /* 36 4 */
u32 map_flags; /* 40 4 */
int spin_lock_off; /* 44 4 */
u32 id; /* 48 4 */
int numa_node; /* 52 4 */
u32 btf_key_type_id; /* 56 4 */
u32 btf_value_type_id; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct btf * btf; /* 64 8 */
struct bpf_map_memory memory; /* 72 16 */
bool unpriv_array; /* 88 1 */
bool frozen; /* 89 1 */
/* XXX 38 bytes hole, try to pack */
/* --- cacheline 2 boundary (128 bytes) --- */
atomic64_t refcnt __attribute__((__aligned__(64))); /* 128 8 */
atomic64_t usercnt; /* 136 8 */
struct work_struct work; /* 144 32 */
char name[16]; /* 176 16 */
/* size: 192, cachelines: 3, members: 21 */
/* sum members: 154, holes: 1, sum holes: 38 */
/* forced alignments: 2, forced holes: 1, sum forced holes: 38 */
} __attribute__((__aligned__(64)));
This patch, while modifying all users of bpf_map_inc, also cleans up its
interface to match bpf_map_put with separate operations for bpf_map_inc and
bpf_map_inc_with_uref (to match bpf_map_put and bpf_map_put_with_uref,
respectively). Also, given there are no users of bpf_map_inc_not_zero
specifying uref=true, remove uref flag and default to uref=false internally.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-2-andriin@fb.com
|
|
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't populate the array exp_mask on the stack but instead make it
static. Makes the object code smaller by 224 bytes.
Before:
text data bss dec hex filename
77832 2290 0 80122 138fa ethernet/netronome/nfp/bpf/jit.o
After:
text data bss dec hex filename
77544 2354 0 79898 1381a ethernet/netronome/nfp/bpf/jit.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add tracing of device-related interaction to aid performance
analysis, especially around resync:
tls:tls_device_offload_set
tls:tls_device_rx_resync_send
tls:tls_device_rx_resync_nh_schedule
tls:tls_device_rx_resync_nh_delay
tls:tls_device_tx_resync_req
tls:tls_device_tx_resync_send
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
In nfp_abm_u32_knode_replace if the allocation for match fails it should
go to the error handling instead of returning. Updated other gotos to
have correct errno returned, too.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In nfp_flower_spawn_vnic_reprs in the loop if initialization or the
allocations fail memory is leaked. Appropriate releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In nfp_flower_spawn_phy_reprs, in the for loop over eth_tbl if any of
intermediate allocations or initializations fail memory is leaked.
requiered releases are added.
Fixes: b94524529741 ("nfp: flower: add per repr private data for LAG offload")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull Kbuild updates from Masahiro Yamada:
- add modpost warn exported symbols marked as 'static' because 'static'
and EXPORT_SYMBOL is an odd combination
- break the build early if gold linker is used
- optimize the Bison rule to produce .c and .h files by a single
pattern rule
- handle PREEMPT_RT in the module vermagic and UTS_VERSION
- warn CONFIG options leaked to the user-space except existing ones
- make single targets work properly
- rebuild modules when module linker scripts are updated
- split the module final link stage into scripts/Makefile.modfinal
- fix the missed error code in merge_config.sh
- improve the error message displayed on the attempt of the O= build in
unclean source tree
- remove 'clean-dirs' syntax
- disable -Wimplicit-fallthrough warning for Clang
- add CONFIG_CC_OPTIMIZE_FOR_SIZE_O3 for ARC
- remove ARCH_{CPP,A,C}FLAGS variables
- add $(BASH) to run bash scripts
- change *CFLAGS_<basetarget>.o to take the relative path to $(obj)
instead of the basename
- stop suppressing Clang's -Wunused-function warnings when W=1
- fix linux/export.h to avoid genksyms calculating CRC of trimmed
exported symbols
- misc cleanups
* tag 'kbuild-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (63 commits)
genksyms: convert to SPDX License Identifier for lex.l and parse.y
modpost: use __section in the output to *.mod.c
modpost: use MODULE_INFO() for __module_depends
export.h, genksyms: do not make genksyms calculate CRC of trimmed symbols
export.h: remove defined(__KERNEL__), which is no longer needed
kbuild: allow Clang to find unused static inline functions for W=1 build
kbuild: rename KBUILD_ENABLE_EXTRA_GCC_CHECKS to KBUILD_EXTRA_WARN
kbuild: refactor scripts/Makefile.extrawarn
merge_config.sh: ignore unwanted grep errors
kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)
modpost: add NOFAIL to strndup
modpost: add guid_t type definition
kbuild: add $(BASH) to run scripts with bash-extension
kbuild: remove ARCH_{CPP,A,C}FLAGS
kbuild,arc: add CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3 for ARC
kbuild: Do not enable -Wimplicit-fallthrough for clang for now
kbuild: clean up subdir-ymn calculation in Makefile.clean
kbuild: remove unneeded '+' marker from cmd_clean
kbuild: remove clean-dirs syntax
kbuild: check clean srctree even earlier
...
|
|
Minor overlapping changes in the btusb and ixgbe drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PluDevice register provides the authoritative chip model/revision.
Since the model number is purely used for reporting purposes, follow
the hardware team convention of subtracting 0x10 from the PluDevice
register to obtain the chip model/revision number.
Suggested-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the 'app_fw_from_flash' HWinfo key is invalid, set the
'fw_load_policy' devlink parameter value to unknown.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed the incorrect prefix for the 'nfp_fw_load' function.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 'reset_dev_on_drv_probe' devlink parameter. The
reset control policy is controlled by the 'abi_drv_reset' hwinfo key.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 'fw_load_policy' devlink parameter. The FW load
policy is controlled by the 'app_fw_from_flash' hwinfo key.
Remap the values from devlink to the hwinfo key and back.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register devlink parameters for driver use. Subsequent patches will add
support for specific parameters.
In order to support devlink parameters, the management firmware needs to
be able to lookup and set hwinfo keys.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware reset and loading policies can be controlled with the
combination of three hwinfo keys, 'abi_drv_reset', 'abi_drv_load_ifc'
and 'app_fw_from_flash'.
'app_fw_from_flash' defines which firmware should take precedence,
'Disk', 'Flash' or the 'Preferred' firmware. When 'Preferred'
is selected, the management firmware makes the decision on which
firmware will be loaded by comparing versions of the flash firmware
and the host supplied firmware.
'abi_drv_reset' defines when the driver should reset the firmware when
the driver is probed, either 'Disk' if firmware was found on disk,
'Always' reset or 'Never' reset. Note that the device is always reset
on driver unload if firmware was loaded when the driver was probed.
'abi_drv_load_ifc' defines a list of PF devices allowed to load FW on
the device.
Furthermore, we limit the cases to where the driver will unload firmware
again when the driver is removed to only when firmware was loaded by the
driver and only if this particular device was the only one that could
have loaded firmware. This is needed to avoid firmware being removed
while in use on multi-host platforms.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the NSP HWinfo set command. This closely follows the
HWinfo lookup command.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are cases where we want to read a hwinfo entry from the NFP, and
if it doesn't exist, use a default value instead.
To support this, we must silence warning/error messages when the hwinfo
entry doesn't exist since this is a valid use case. The NSP command
structure provides the ability to silence command errors, in which case
the caller should log any command errors appropriately. Protocol errors
are unaffected by this.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the simple command that indicates whether application
firmware is loaded.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flower control message replies are handled in different locations. The truly
high priority replies are handled in the BH (tasklet) context, while the
remaining replies are handled in a predefined Linux work queue. The work
queue handler orders replies into high and low priority groups, and always
start servicing the high priority replies within the received batch first.
Reply Type: Rtnl Lock: Handler:
CMSG_TYPE_PORT_MOD no BH tasklet (mtu)
CMSG_TYPE_TUN_NEIGH no BH tasklet
CMSG_TYPE_FLOW_STATS no BH tasklet
CMSG_TYPE_PORT_REIFY no WQ high
CMSG_TYPE_PORT_MOD yes WQ high (link/mtu)
CMSG_TYPE_MERGE_HINT yes WQ low
CMSG_TYPE_NO_NEIGH no WQ low
CMSG_TYPE_ACTIVE_TUNS no WQ low
CMSG_TYPE_QOS_STATS no WQ low
CMSG_TYPE_LAG_CONFIG no WQ low
A subset of control messages can block waiting for an rtnl lock (from both
work queue priority groups). The rtnl lock is heavily contended for by
external processes such as systemd-udevd, systemd-network and libvirtd,
especially during netdev creation, such as when flower VFs and representors
are instantiated.
Kernel netlink instrumentation shows that external processes (such as
systemd-udevd) often use successive rtnl_trylock() sequences, which can result
in an rtnl_lock() blocked control message to starve for longer periods of time
during rtnl lock contention, i.e. netdev creation.
In the current design a single blocked control message will block the entire
work queue (both priorities), and introduce a latency which is
nondeterministic and dependent on system wide rtnl lock usage.
In some extreme cases, one blocked control message at exactly the wrong time,
just before the maximum number of VFs are instantiated, can block the work
queue for long enough to prevent VF representor REIFY replies from getting
handled in time for the 40ms timeout.
The firmware will deliver the total maximum number of REIFY message replies in
around 300us.
Only REIFY and MTU update messages require replies within a timeout period (of
40ms). The MTU-only updates are already done directly in the BH (tasklet)
handler.
Move the REIFY handler down into the BH (tasklet) in order to resolve timeouts
caused by a blocked work queue waiting on rtnl locks.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Continue is not needed at the bottom of a loop.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2019-08-31
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix 32-bit zero-extension during constant blinding which
has been causing a regression on ppc64, from Naveen.
2) Fix a latency bug in nfp driver when updating stack index
register, from Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each get_next and lookup call requires a round trip to the device.
However, the device is capable of giving us a few entries back,
instead of just one.
In this patch we ask for a small yet reasonable number of entries
(4) on every get_next call, and on subsequent get_next/lookup calls
check this little cache for a hit. The cache is only kept for 250us,
and is invalidated on every operation which may modify the map
(e.g. delete or update call). Note that operations may be performed
simultaneously, so we have to keep track of operations in flight.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
If control channel MTU is too low to support map operations a warning
will be printed. This is not enough, we want to make sure probe fails
in such scenario, as this would clearly be a faulty configuration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfedab5 ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor conflict in r8169, bug fix had two versions in net
and net-next, take the net-next hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MODULE_FIRMWARE entries for AMDA0058 boards.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP is using Local Memory to model stack. LM_addr could be used as base of
a 16 32-bit word region of Local Memory. Then, if the stack offset is
beyond the current region, the local index needs to be updated. The update
needs at least three cycles to take effect, therefore the sequence normally
looks like:
local_csr_wr[ActLMAddr3, gprB_5]
nop
nop
nop
If the local index switch happens on a narrow loads, then the instruction
preparing value to zero high 32-bit of the destination register could be
counted as one cycle, the sequence then could be something like:
local_csr_wr[ActLMAddr3, gprB_5]
nop
nop
immed[gprB_5, 0]
However, we have zero extension optimization that zeroing high 32-bit could
be eliminated, therefore above IMMED insn won't be available for which case
the first sequence needs to be generated.
Fixes: 0b4de1ff19bf ("nfp: bpf: eliminate zero extension code-gen")
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Now that the single target build descends into sub-directories in the
same way as the normal build, these dummy Makefiles are not needed
any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When processing FLOW_BLOCK_BIND command on indirect block, check that flow
block cb is not busy.
Fixes: 0d4fd02e7199 ("net: flow_offload: add flow_block_cb_is_busy() and use it")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge conflict of mlx5 resolved using instructions in merge
commit 9566e650bf7fdf58384bb06df634f7531ca3a97e.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Edwin Peer <edwin.peer@netronome.com>
Cc: Yangtao Li <tiny.windzz@gmail.com>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
move tc indirect block to flow_offload and rename
it to flow indirect block.The nf_tables can use the
indr block architecture.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just minor overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a tunnel packet arrives on the NFP card, its destination MAC is
looked up and MAC index returned for it. This index can help verify the
tunnel by, for example, ensuring that the packet arrived on the expected
port. If the packet is destined for a known MAC that is not connected to a
given physical port then the mac index can have a global value (e.g. when
a series of bonded ports shared the same MAC).
If the packet is to be detunneled at a bridge device or internal port like
an Open vSwitch VLAN port, then it should first match a 'pre-tunnel' rule
to direct it to that internal port.
Use the MAC index to indicate if a packet should match a pre-tunnel rule
before decap is allowed. Do this by tracking the number of internal ports
associated with a MAC address and, if the number if >0, set a bit in the
mac_index to forward the packet to the pre-tunnel table before continuing
with decap.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAC addresses along with an identifying index are offloaded to firmware to
allow tunnel decapsulation. If a tunnel packet arrives with a matching
destination MAC address and a verified index, it can continue on the
decapsulation process. This replicates the MAC verifications carried out
in the kernel network stack.
When a netdev is added to a bridge (e.g. OvS) then packets arriving on
that dev are directed through the bridge datapath instead of passing
through the network stack. Therefore, tunnelled packets matching the MAC
of that dev will not be decapped here.
Replicate this behaviour on firmware by removing offloaded MAC addresses
when a MAC representer is added to an OvS bridge. This can prevent any
false positive tunnel decaps.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules are TC flower and OvS rules that forward a packet to the
tunnel end point where it can then pass through the network stack and be
decapsulated. These are required if the tunnel end point is, say, an OvS
internal port.
Currently, firmware determines that a packet is in a tunnel and decaps it
if it has a known destination IP and MAC address. However, this bypasses
the flower pre-tunnel rule and so does not update the stats. Further to
this it ignores VLANs that may exist outside of the tunnel header.
Offload pre-tunnel rules to the NFP. This embeds the pre-tunnel rule into
the tunnel decap process based on (firmware) mac index and VLAN. This
means that decap can be carried out correctly with VLANs and that stats
can be updated for all kernel rules correctly.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules must direct packets to an internal port based on L2
information. Rules that egress to an internal port are already indicated
by a non-NULL device in its nfp_fl_payload struct. Verfiy the rest of the
match fields indicate that the rule is a pre-tunnel rule. This requires a
full match on the destination MAC address, an option VLAN field, and no
specific matches on other lower layer fields (with the exception of L4
proto and flags).
If a rule is identified as a pre-tunnel rule then mark it for offload to
the pre-tunnel table. Similarly, remove it from the pre-tunnel table on
rule deletion. The actual offloading of these commands is left to a
following patch.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-tunnel rules are used when the tunnel end-point is on an 'internal
port'. These rules are used to direct the tunnelled packets (based on outer
header fields) to the internal port where they can be detunnelled. The
rule must send the packet to ingress the internal port at the TC layer.
Currently FW does not support an action to send to ingress so cannot
offload such rules. However, in preparation for populating the pre-tunnel
table to represent such rules, check for rules that send to the ingress of
an internal port and mark them as such. Further validation of such rules
is left to subsequent patches.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP allows the merging of 2 flows together into a single offloaded flow.
In the kernel datapath the packet must match 1 flow, impliment its
actions, recirculate, match the 2nd flow and also impliment its actions.
Merging creates a single flow with all actions from the 2 original flows.
Firmware impliments a tunnel header push as the packet is about to egress
the card. Therefore, if the first merge rule candiate pushes a tunnel,
then the second rule can only have an egress action for a valid merge to
occur (or else the action ordering will be incorrect). This prevents the
pushing of a tunnel header followed by the pushing of a vlan header.
In order to support this behaviour, firmware allows VLAN information to
be encoded in the tunnel push action. If this is non zero then the fw will
push a VLAN after the tunnel header push meaning that 2 such flows with
these actions can be merged (with action order being maintained).
Support tunnel in VLAN pushes by encoding VLAN information in the tunnel
push action of any merge flow requiring this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-07-25
This series introduces some fixes to mlx5 driver.
1) Ariel is addressing an issue with enacp flow counter race condition
2) Aya fixes ethtool speed handling
3) Edward fixes modify_cq hw bits alignment
4) Maor fixes RDMA_RX capabilities handling
5) Mark reverses unregister devices order to address an issue with LAG
6) From Tariq,
- wrong max num channels indication regression
- TLS counters naming and documentation as suggested by Jakub
- kTLS, Call WARN_ONCE on netdev mismatch
There is one patch in this series that touches nfp driver to align
TLS statistics names with latest documentation, Jakub is CC'ed.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5: Use reversed order when unregister devices')
For -stable v4.20
('net/mlx5e: Prevent encap flow counter update async to user query')
('net/mlx5: Fix modify_cq_in alignment')
For -stable v5.1
('net/mlx5e: Fix matching of speed to PRM link modes')
For -stable v5.2
('net/mlx5: Add missing RDMA_RX capabilities')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align to the naming convention in TLS documentation.
Fixes: 51a5e563298d ("nfp: tls: add basic statistics")
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Recent additions to the kernel include a TC action module to manipulate
MPLS headers on packets. Such actions are available to offload via the
flow_offload intermediate representation API.
Modify the NFP driver to allow the offload of MPLS set actions to
firmware. Set actions update the outermost MPLS header. The offload
includes a mask to specify which fields should be set.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Taehee Yoo
Andrii Nakryiko
David S. Miller
Colin Ian King
Jakub Kicinski
Linus Torvalds
Navid Emamdoost
Dirk van der Merwe
Fred Lotter
zhong jiang
John Hurley
Jiong Wang
Masahiro Yamada
Vlad Buslov
Pablo Neira Ayuso
Greg Kroah-Hartman
wenxu
Tariq Toukan