| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch adds in the ecore 2 new personalities in addition to
QED_PCI_ETH - QED_PCI_ISCSI and QED_PCI_ETH_ROCE.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the qed portion of the RoCE & iSCSI firmware HSI,
as well as adding several new common HSI files which would be required
by both qed and qed* protocols.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].
This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The New QED firmware contains several fixes, including:
- Wrong classification of packets in 4-port devices.
- Anti-spoof interoperability with encapsulated packets.
- Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.
In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc warns about qed_fill_link possibly accessing uninitialized data:
drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]
While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.
This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.
The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.
As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently 100g devices don't support minimum/maximum BW configurations,
yet link flaps might cause the driver to attempt to do such a
configuration. Prevent this just as we do for the maximum BW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapter can support 100g in both MSIx and INTa, but not in MSI.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the HW configurations are currently missing for 100g devices.
This can cause various classification issues, as well as prevent device
from fully reaching line-rate.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When DCBx re-negotiation is occurring, the PF's configurations for
maximum and minimum bandwidth guarantees are currently lost.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 39651abd2814 ("qed: add support for dcbx") is re-configuring
the QM hw-block as part of its sequence. This is done in attention
handling context which is non-sleepable, yet memory is allocated in
this flow using GFP_KERNEL.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PFs and VFs differ in their registered ethtool operations,
but they're using a common function for get_sset_count().
As a result, `ethtool -i' for a VF would indicate it supports
selftest, although that's not the case.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.
[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the coding error in determining the enable flag for
the application/protocol. The enable flag should be set for all protocols
but the eth.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One timer, whose handler keeps reading on MMIO register for EEH
core to detect error in time, is started when the PCI device driver
is loaded. MMIO register can't be accessed during PE reset in EEH
recovery. Otherwise, the unexpected recursive error is triggered.
The timer isn't closed that time if the interface isn't brought
up. So the unexpected recursive error is seen during EEH recovery
when the interface is down.
This avoids the unexpected recursive EEH error by closing the timer
in qlge_io_error_detected() before EEH PE reset unconditionally. The
timer is started unconditionally after EEH PE reset in qlge_io_resume().
Also, the timer should be closed unconditionally when the device is
removed from the system permanently in qlge_io_error_detected().
Reported-by: Shriya R. Kulkarni <shriyakul@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"priority" needs to be signed for the error handling to work.
Fixes: 39651abd2814 ('qed: add support for dcbx.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes and more updates from David Miller:
1) Tunneling fixes from Tom Herbert and Alexander Duyck.
2) AF_UNIX updates some struct sock bit fields with the socket lock,
whereas setsockopt() sets overlapping ones with locking. Seperate
out the synchronized vs. the AF_UNIX unsynchronized ones to avoid
corruption. From Andrey Ryabinin.
3) Mount BPF filesystem with mount_nodev rather than mount_ns, from
Eric Biederman.
4) A couple kmemdup conversions, from Muhammad Falak R Wani.
5) BPF verifier fixes from Alexei Starovoitov.
6) Don't let tunneled UDP packets get stuck in socket queues, if
something goes wrong during the encapsulation just drop the packet
rather than signalling an error up the call stack. From Hannes
Frederic Sowa.
7) SKB ref after free in batman-adv, from Florian Westphal.
8) TCP iSCSI, ocfs2, rds, and tipc have to disable BH in it's TCP
callbacks since the TCP stack runs pre-emptibly now. From Eric
Dumazet.
9) Fix crash in fixed_phy_add, from Rabin Vincent.
10) Fix length checks in xen-netback, from Paul Durrant.
11) Fix mixup in KEY vs KEYID macsec attributes, from Sabrina Dubroca.
12) RDS connection spamming bug fixes from Sowmini Varadhan
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
net: suppress warnings on dev_alloc_skb
uapi glibc compat: fix compilation when !__USE_MISC in glibc
udp: prevent skbs lingering in tunnel socket queues
bpf: teach verifier to recognize imm += ptr pattern
bpf: support decreasing order in direct packet access
net: usb: ch9200: use kmemdup
ps3_gelic: use kmemdup
net:liquidio: use kmemdup
bpf: Use mount_nodev not mount_ns to mount the bpf filesystem
net: cdc_ncm: update datagram size after changing mtu
tuntap: correctly wake up process during uninit
intel: Add support for IPv6 IP-in-IP offload
ip6_gre: Do not allow segmentation offloads GRE_CSUM is enabled with FOU/GUE
RDS: TCP: Avoid rds connection churn from rogue SYNs
RDS: TCP: rds_tcp_accept_worker() must exit gracefully when terminating rds-tcp
net: sock: move ->sk_shutdown out of bitfields.
ipv6: Don't reset inner headers in ip6_tnl_xmit
ip4ip6: Support for GSO/GRO
ip6ip6: Support for GSO/GRO
ipv6: Set features for IPv6 tunnels
...
|
|
Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many developers already know that field for reference count of the
struct page is _count and atomic type. They would try to handle it
directly and this could break the purpose of page reference count
tracepoint. To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code. After that, developer
who need to handle reference count will find that field should not be
accessed directly.
[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF's probe might log that it has no PM capability in its PCI configuration
space. As this is a valid configuration, silence such prints.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.
This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.
Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.
To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seems like something broke in commit 1408cc1fa48c ("qed: Introduce VFs")
and the function no longer verifies that the vf is indeed a valid one.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a PCI callback for `sriov_configure' and a new PCI device id for
the VF [+ Some minor changes to accomodate differences between PF and VF
at the qede].
Following this, VF creation should be possible and the entire subset of
existing PF functionality that's allow to VFs should be supported.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If qlcnic_fw_cmd_get_minidump_temp() fails then "fw_dump->tmpl_hdr" is
NULL or possibly freed. It can lead to an oops later.
Fixes: d01a6d3c8ae1 ('qlcnic: Add support to enable capability to extend minidump for iSCSI')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"data_split" was never set to false. It's just uninitialized.
Fixes: 2950219d87b0 ('qede: Add basic network device support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error handling is broken here. netxen_rom_fast_read() returns zero
on success and -EIO on error. It never returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My static checker complains that we are using "autoneg" without
initializing it. The problem is the ->phy_read() condition is reversed
so we only set this on error instead of success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My static checker complained that "v" can be used unintialized if
netxen_rom_fast_read() returns -EIO. That function never actually
returns -1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qede requires qed to provide enough resources to accommodate 16 combined
channels, but that upper-bound isn't actually being enforced by it.
Instead, qed inform back to qede how many channels can be opened based on
available resources - but that calculation doesn't really take into account
the resources requested by qede; Instead it considers other FW/HW available
resources.
As a result, if a user would increase the number of channels to more than
16 [e.g., using ethtool] the chip would hang.
This change increments the resources requested by qede to 64 combined
channels instead of 16; This value is an upper bound on the possible
available channels [due to other FW/HW resources].
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:
struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)
Compile tested only.
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Yuval Mintz
Arnd Bergmann
Sudarsana Reddy Kalluru
Gavin Shan
Dan Carpenter
Linus Torvalds
Manish Chopra
Joonsoo Kim
David S. Miller
Florian Westphal