| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Bind direct blocks for the MAE-admin PF and each VF representor.
Currently these connect to a stub efx_tc_flower() that only returns
-EOPNOTSUPP; subsequent patches will implement flower offloads to the
Match-Action Engine.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Default rules are low-priority switching rules which the hardware uses
in the absence of higher-priority rules. Each representor requires a
corresponding rule matching traffic from its representee VF and
delivering to the PF (where a check on INGRESS_MPORT in
__ef100_rx_packet() will direct it to the representor). No rule is
required in the reverse direction, because representor TX uses a TX
override descriptor to bypass the MAE and deliver directly to the VF.
Since inserting any rule into the MAE disables the firmware's own
default rules, also insert a pair of rules to connect the PF to the
physical network port and vice-versa.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An MAE port, or m-port, is a port (source/destination for traffic) on
the Match-Action Engine (the internal switch on EF100).
Representors will use their representee's m-port for two purposes: as
a destination override on TX from the representor, and as a source
match in 'default rules' to steer representee traffic (when not
matched by e.g. a TC flower rule) to representor RX via the parent
PF's receive queue.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No net_device_ops yet, just a placeholder netdev created per VF.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the (un)load message more specific to differentiate it from
the sfc.ko messages.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Disable the build of Siena code until later in this patch series.
Prevent sfc.ko from binding to Siena NICs.
efx_init_sriov/efx_fini_sriov is only used for Siena. Remove calls
to those.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the EF100 PF driver by adding .sriov_configure()
which would allow users to enable and disable virtual functions
using the sriov sysfs.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/75e74d9e-14ce-0524-9668-5ab735a7cf62@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No TX or RX path, no MCDI, not even an ifup/down handler.
Besides stubs, the bulk of the patch deals with reading the Xilinx
extended PCIe capability, which tells us where to find our BAR.
Though in the same module, EF100 has its own struct pci_driver,
which is named sfc_ef100.
A small number of additional nic_type methods are added; those in the
TX (tx_enqueue) and RX (rx_packet) paths are called through indirect
call wrappers to minimise the performance impact.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Various ethtool entry points are moved.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One function was renamed here, the other contains code extracted from
another.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The moved code handles MCDI port link state and capabilities.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once again, a tiny bit of refactoring was required to stitch the code
together (i.e. adding headers). The moved code deals with managing tx
queues and mappings.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The moved code deals with managing rx buffers and queues.
A tiny bit of refactoring was required in other files to stitch the
code together.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just a handful of function, but also removed many 'static' identifiers
so the code builds. These will, of course, be moved.
Module parameters for IRQ moderation threshold also moved.
Small code styling fixes included.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Small functions doing work that will be common, related to reset
workqueue management.
Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both SFC and SFC_FALCON depend on NET_VENDOR_SOLARFLARE, hence use the
latter to decide whether to descend into the sfc subdirectory.
Move the rule to descend into sfc/falcon to the sfc subdirectory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task
of TCP segmentation to the firmware, such that we now just pass a single
super-packet to the NIC. This means TSO has a great deal in common with a
normal DMA transmit, apart from adding a couple of option descriptors.
NIC-specific checks have been moved off the fast path and in to
initialisation where possible.
This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit
and some error handling is now outside TSO, since it is common with other
code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the use of sriov_configure on EF10
to enable Virtual Functions while the driver is loaded.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the EF10 network controller architecture and the
SFC9100 family, starting with SFC9120 'Farmingdale', and bumps the
driver version to 4.0.
New features in the SFC9100 family include:
- Flexible allocation of internal resources to PCIe physical and virtual
functions under firmware control
- RX event merging to reduce DMA writes at high packet rates
- Integrated RX timestamping
- PIO buffers for lower TX latency
- Firmware-driven data path that supports additional offload features
and filter types
- Delivery of packets between functions and to multiple recipients,
allowing firmware to implement a vswitch
- Multiple RX flow hash (RSS) contexts with their own hash keys and
indirection tables
- 40G MAC (single port only)
...not all of which are enabled in this initial driver or the initial
firmware release.
Much of the new code is by Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add efx_nic_type operations for the many efx_nic functions that need
to be implemented different on EF10. For now, change most of the
existing efx_nic_*() functions into inline wrappers. As a later step,
we may be able to improve branch prediction for operations used on the
fast path by copying the pointers into each queue/channel structure.
Move the Falcon/Siena implementations to new file farch.c and rename
the functions and static data to use a prefix of 'efx_farch_'.
Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also
use it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Collect together MCDI port functions from mcdi.c, mcdi_mac.c,
mcdi_phy.c and siena.c. Rename the 'siena' functions accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
In particular, fold in the whole of falcon_xmac.c.
Drop some entirely unused definitions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors. The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.
Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware. Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
Edward Cree
Martin Habets
Martin Habets
Pieter Jansen van Vuuren
Edward Cree
Alex Maftei (amaftei)
Geert Uytterhoeven
Greg Kroah-Hartman
Bert Kenward
Shradha Shah
Ben Hutchings
Stuart Hodgson
Jeff Kirsher