| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since commit b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications
instead of switchdev calls") we reflect to the device the entire FIB
table and not only FIBs that point to netdevs created by the driver.
During module removal, FIBs of the second type are removed following
NETDEV_UNREGISTER events sent. The other FIBs are still present in both
the driver's cache and the device's table.
Fix this by iterating over all the FIB tables in the device and flush
them. There's no need to take locks, as we're the only writer.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 52f95bbfcf72 ("stmmac: fix adjust link call in case of a switch
is attached") added some logic to avoid polling the fixed PHY and
therefore invoking the adjust_link callback more than once, since this
is a fixed PHY and link events won't be generated.
This works fine the first time, because we start with phydev->irq =
PHY_POLL, so we call adjust_link, then we set phydev->irq =
PHY_IGNORE_INTERRUPT and we stop polling the PHY.
Now, if we called ndo_close(), which calls both phy_stop() and does an
explicit netif_carrier_off(), we end up with a link down. Upon calling
ndo_open() again, despite starting the PHY state machine, we have
PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the
link is permanently down.
Fixes: 52f95bbfcf72 ("stmmac: fix adjust link call in case of a switch is attached")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In-flight DMA from 1st kernel could continue going in kdump kernel.
New io-page table has been created before bnx2 does reset at open stage.
We have to wait for the in-flight DMA to complete to avoid it look up
into the newly created io-page table at probe stage.
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3e1be7ad2d38c6bd6aeef96df9bd0a7822f4e51c.
When people build bnx2 driver into kernel, it will fail to detect
and load firmware because firmware is contained in initramfs and
initramfs has not been uncompressed yet during do_initcalls. So
revert commit 3e1be7a and work out a new way in the later patch.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake "unmached" to "unmatched" in
debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake "successed" to "succeeded"
in debug message. Also unwrap multi-line literal string.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This mistake was causing debugfs directory creation
failures when multiple ibmvnic devices were probed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This structure was mapped but never subsequently unmapped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
efx_copy_channel() doesn't correctly clear the napi_hash related state.
This means that when napi_hash_add is called for that channel nothing is
done, and we are left with a copy of the napi_hash_node from the old
channel. When we later call napi_hash_del() on this channel we have a
stale napi_hash_node.
Corruption is only seen when there are multiple entries in one of the
napi_hash lists. This is made more likely by having a very large number
of channels. Testing was carried out with 512 channels - 32 channels on
each of 16 ports.
This failure typically appears as protection faults within napi_by_id()
or napi_hash_add(). efx_copy_channel() is only used when tx or rx ring
sizes are changed (ethtool -G).
Fixes: 36763266bbe8 ("sfc: Add support for busy polling")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device's neighbour table is periodically dumped in order to update
the kernel about active neighbours. A single dump session may span
multiple queries, until the response carries less records than requested
or when a record (can contain up to four neighbour entries) is not full.
Current code stops the session when the number of returned records is
zero, which can result in infinite loop in case of high packet rate.
Fix this by stopping the session according to the above logic.
Fixes: c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.
Fix this by initializing the reference count to 1.
Also add a warning to put function.
Fixes: 763b4b70afcd ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the physical link is down and the VF virtual link is set to "enable",
the current code does not always work. If the link is down but the
cable is attached, the firmware returns LINK_SIGNAL instead of
NO_LINK. The current code is treating LINK_SIGNAL as link up.
The fix is to treat link as down when the link_status != LINK.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic is missing the check on whether the tx and rx rings are sharing
completion rings or not.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since now, the table with same id in multiple netnamespaces were squashed
to a single virtual router. That is not only incorrect, it also causes
error messages when trying to use RALUE register to do double remove
of FIB entries, like this one:
mlxsw_spectrum 0000:03:00.0: EMAD reg access failed (tid=facb831c00007b20,reg_id=8013(ralue),type=write,status=7(bad parameter))
Since we don't allow ports to change namespaces (NETIF_F_NETNS_LOCAL),
and the infrastructure is not yet prepared to handle netnamespaces, just
ignore FIB notification events for non-init namespaces. That is clear to
do since we don't need to offload them.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__neigh_create function works in a different way than assumed.
It passes "n" as a parameter to ndo_neigh_construct. But this "n" might
be destroyed right away before __neigh_create() returns in case there is
already another neighbour struct in the hashtable with the same dev and
primary key. That is not expected by mlxsw_sp_router_neigh_construct()
and the stored "n" points to freed memory, eventually leading to crash.
Fix this by doing tight 1:1 coupling between neighbour struct and
internal driver neigh_entry. That allows to narrow down the key in
internal driver hashtable to do lookups by "n" only.
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous fix has broken RoCE support as the rdma_pf_params are now
being set into the parameters only after the params are alrady assigned
into the hw-function.
Fixes: 0189efb8f4f8 ("qed*: Fix Kconfig dependencies with INFINIBAND_QEDR")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently RoCE v2 won't operate with RDMA CM due to missing setting of
the roce-flavour in the ll2 configuration.
This patch properly sets the flavour, and deletes incorrect HSI
that doesn't [yet] exist.
Fixes: abd49676c707 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the PHY has been configured to allow pause frames, then the MAC
should be configured to generate and/or accept those frames.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause frames are used to enable flow control. A MAC can send and
receive pause frames in order to throttle traffic. However, the PHY
must be configured to allow those frames to pass through.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes regression introduced by patch adding feature flags. It was
already reported and patch followed (it got accepted) but it appears it
was incorrect. Instead of fixing reversed condition it broke a good one.
This patch was verified to actually fix SoC hanges caused by bgmac on
BCM47186B0.
Fixes: db791eb2970b ("net: ethernet: bgmac: convert to feature flags")
Fixes: 4af1474e6198 ("net: bgmac: Fix errant feature flag check")
Cc: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.
bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.
Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9d2afba058722d40cc02f430229c91611c0e8d16.
The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.
The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.
Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When prof_sel is invalid, mlx5_core_warn is called but the
mlx5_core_dev is not initialized yet. Solution is moving the prof_sel code
after dev->pdev assignment
Fixes: 2974ab6e8bd8 ('net/mlx5: Improve driver log messages')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the current generation of the mlx5 HW (CX4/CX4-Lx) per flow vlan
push/pop actions are emulated, we must not program them to the firmware.
Fixes: f5f82476090f ('net/mlx5: E-Switch, Support VLAN actions in the offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We ignored the vlan priority in offloaded TC rules matching part,
fix that.
Fixes: 095b6cfd69ce ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF reps should be altogether on the same NS as they were created.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mlx5e_open_channel CQs must be created before napi is enabled.
Here we move the XDP CQ creation to satisfy that fact.
mlx5e_close_channel is already working according to the right order.
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of mlx5e_open_rq fails the error handling will jump to
label err_close_xdp_sq and will try to close the xdp_sq unconditionally.
xdp_sq is valid only in case of XDP use cases, i.e priv->xdp_prog is
not null.
To fix this in this patch we test xdp_sq validity prior to closing it.
In addition we now close the xdp_sq.cq as well.
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver allocates replacement buffers before-hand to make
sure whenever an aggregation begins there would be a replacement
for the Rx buffers, as we can't release the buffer until
aggregation is terminated and driver logic assumes the Rx rings
are always full.
For every other Rx page that's being allocated [I.e., regular]
the page is being completely mapped while for the replacement
buffers only the first portion of the page is being mapped.
This means that:
a. Once replacement buffer replenishes the regular Rx ring,
assuming there's more than a single packet on page we'd post unmapped
memory toward HW [assuming mapping is actually done in granularity
smaller than page].
b. Unmaps are being done for the entire page, which is incorrect.
Fixes: 55482edc25f06 ("qede: Add slowpath/fastpath support and enable hardware GRO")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The coalesce settings behave badly when changing just one value:
... # ethtool -c eth0
rx-usecs: 249
... # ethtool -C eth0 tx-usecs 250
... # ethtool -c eth0
rx-usecs: 248
This occurs due to rounding errors when calculating the microseconds
value - the divisons round down. This causes (eg) the rx-usecs to
decrease by one every time the tx-usecs value is set as per the above.
Fix this by making the divison round-to-nearest.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'create_root_ns()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be
set to 0, not 6, on the Qualcomm Technologies QDF2432.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the interrupt trigger region id to 2 and the
corresponding threshold set0/set1 values to 8/16.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since ethernet v1 hardware has a bug related to coalescing, disabling
this feature.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde1f29 ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.
Fixes: 9a4d7e86acf3 ("qede: Add support for Tx/Rx-only queues.")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
|
|
Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.
This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.
Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.
Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.
In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 8d7533e5aaad1c94386a8101a36b0617987966b7.
It introduced kbuild failures, new version coming.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-10-27
This series contains fixes to ixgbe and i40e.
Emil fixes a NULL pointer dereference when a macvlan interface is brought
up while the PF is still down.
David root caused the original panic that was fixed by commit id
(a036244c068612 "i40e: Fix kernel panic on enable/disable LLDP") and the
fix was not quite correct, so removed the get_default_tc() and replaced
it with a #define since there is only one TC supported as a default.
Guilherme Piccoli fixes an issue where if we modprobe the driver module
without enough MSI-X interrupts, then unload the module and reload it
again, the kernel would crash. So if we fail to allocate enough MSI-X
interrupts, we should disable them since they were previously enabled.
Huaibin Wang found that the order of the arguments for
ndo_dflt_bridge_getlink() were in the correct order, so fix the order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Ido Schimmel
Florian Fainelli
Baoquan He
Colin Ian King
Thomas Falcon
Bert Kenward
Arkadi Sharshevsky
Yotam Gigi
Michael Chan
Jiri Pirko
Ram Amrani
John Allen
Timur Tabi
Rafał Miłecki
Benjamin Poirier
Tariq Toukan
Johan Hovold
Huy Nguyen
Or Gerlitz
Saeed Mahameed
Guilherme G. Piccoli
Mintz, Yuval
Hariprasad Shenai
Russell King
Christophe Jaillet
Iyappan Subramanian
Andy Gospodarek
Linus Torvalds
Govindarajulu Varadarajan
David S. Miller