| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The new PBA format is stored as a string. This patch allows the
driver to support both the old and new format.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new MAC type X540 shares much of the same functionality of
some silicon specific functions. To reduce duplicate code,
made these functions generic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the high and low water marks for PFC are being set
conservatively for jumbo frames. This means the RX buffers
are being underutilized in the default 1500 MTU. This patch
fixes this so that the water marks are set as described in
the data sheet considering the MTU size.
The equation used is,
RTT * 1.44 + MTU * 1.44 + MTU
Where RTT is the round trip time and MTU is the max frame size
in KB. To avoid floating point arithmetic FC_HIGH_WATER is
defined
((((RTT + MTU) * 144) + 99) / 100) + MTU
This changes how the hardware field fc.low_water and
fc.high_water are used. With this change they are no longer
storing the actual low water and high water markers but are
storing the required head room in the buffer. This simplifies
the logic and we do not need to account for the size of the
buffer when setting the thresholds.
Testing with iperf and 16 threads showed a slight uptick in
throughput over a single traffic class .1-.2Gbps and a reduction
in pause frames. Without the patch a 30 second run would show
~10-15 pause frames being transmitted with the patch ~2-5 are
seen. Test were run back to back with 82599.
Note RXPBSIZE is in KB and low and high water marks fields are
also in KB. However the FCRT* registers are 32B granularity and
right shifted 5 into the register,
(((rx_pbsize - water_mark) * 1024) / 32) << 5
is the most explicit conversion here we simplify
(rx_pbsize - water_mark) * 32 << 5 = (rx_pbsize - water_mark) << 10
This patch updates the PFC thresholds and legacy FC thresholds.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Following patch fixes warnings reported by `make namespacecheck`
Reported by Stephen Hemminger
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove functions that are declared, but not used in the driver.
This patch fixes warnings reported by `make namespacecheck`
Reported by Stephen Hemminger
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
* get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
* set_vfta, fc_enable, init_uta_tables
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.
Issue discovered by Ben Greear when using mac-vlans.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes an issue when clearing out the RAR entries. If RAR[0]
is the only address in use, don't clear the others.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82598 shouldn't try and access LINKS2 while configuring
link and flow control. This is an 82599-only register.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow Control autoneg should be disabled for certain adapters
that don't support autonegotiation of Flow Control at 10 gigabit.
These interfaces are the 10GBASE-T devices, CX4, and SFP+, all
running at 10 gigabit only. 1 gigabit is fine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ccffad25b5136958d4769ed6de5e87992dd9c65c changed parameters for function
ixgbe_update_uc_addr_list_generic but parameter description was not updated.
This patch corrects it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Backplane flow control autonegotiation is currently broken for
ixgbe devices. This patch fixes the flow control issues
with clause 37 autoneg.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have some ~40 functions that were being called out with 'make
namespacecheck'. This patch changes these functions to be static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 has a FW running that helps manage the internal SFI PHY. There are
also a number of pre-production samples of these SFI-based devices in the
field. This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified. The driver will continue loading
though, with no functional degradation.
Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner. This will restart the autotry
mechanism to get link into a known state. The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
82599 supports using either link flow control or priority flow control when
in DCB mode. The dcbnl interface already supports sending down
configurations through rtnetlink that can enable LFC when DCB is enabled,
so the driver should take advantage of this.
82598 does not support using LFC when DCB is enabled, so explicitly disable
it when we're in DCB mode. This means we always run in PFC mode when DCB
is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This sets the low water threshhold for priority flow control for 82598
and 82599 controllers in DCB mode.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After acquiring the SAN MAC address from the EEPROM, we need to program it
into one of the RARs. Also, DCB will use this MAC address to run DCBX
commands, so it doesn't have to play musical MAC addresses when things like
bonding enter the picture. So we need to return the MAC address through
the netlink interface to userspace.
This also moves the init_rx_addrs() call out of start_hw() and into
reset_hw(). We shouldn't try to read any of the RAR information before
initializing our internal accounting of the RAR table, which was what
was happening.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
Documentation/isdn/00-INDEX
drivers/net/wireless/iwlwifi/iwl-scan.c
drivers/net/wireless/rndis_wlan.c
net/mac80211/main.c
|
|
The current code writes the PME enabled bit in PCI config space which is
wrong. This was needed for pre-release hardware, and was not removed from
the driver. Also, we need to clear the WUS (wake up status) after we
resume. Otherwise we can't wake for the same event again since it's still
asserted in the hardware. Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When flow control is disabled, an invalid low/high watermark configuration
should not matter.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The discard pause frames bit was not enabled, so flow control frames could
be passed up to the host. Enabled DPF to keep the frames off the stack.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were basicly ignoring ethtool users request for FC autoneg
and replying to queries with a "best guess". This patch
enables the driver to store if we want to enable/disable
autoneg FC and do the correct behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing DCB parameters, ixgbe needs to have the MAC reset. The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the hardware initialization code specific to 82599. This
is similar to the 82598 hardware initialization code. It also includes all
changes to the existing hardware init code to support 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow control handling is overly complicated and difficult to maintain.
This patch cleans up the flow control handling and makes it much more
explicit. It also adds 1G flow control autonegotiation, for 1G copper
links, 1G KX links, and 1G fiber links.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code has some flaws in it when performing autonegotiation,
especially on KX/KX4 links. This patch updates the code to better handle
the autonegotiation states on link setup. The patch also removes a redundant
link configuration call on driver load, and moves link configuration to
the ->open() path.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New year, new copyright date ranges. Also bump the driver version
number to reflect many of the recent changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
after the most recent patches, the driver was not using the
correct iterator for updating the receive address registers (RAR)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.
This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Don Skidmore
John Fastabend
Emil Tantilov
Jeff Kirsher
Mallikarjuna R Chilakala
Jiri Pirko
David S. Miller
Shannon Nelson
hartleys
PJ Waskiewicz
Jesse Brandeburg
Christopher Leech
Joe Perches
Auke Kok