aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/sfp-bus.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2022-10-10net: sfp: fill also 5gbase-r and 25gbase-r modes in sfp_parse_support()Marek Behún1-0/+3
Fill in also 5gbase-r and 25gbase-r PHY interface modes into the phy_interface_t bitmap in sfp_parse_support(). Fixes: fd580c983031 ("net: sfp: augment SFP parsing with phy_interface_t bitmap") Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20221007084844.20352-1-kabel@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03net: sfp: augment SFP parsing with phy_interface_t bitmapRussell King1-18/+57
We currently parse the SFP EEPROM to a bitmap of ethtool link modes, and then attempt to convert the link modes to a PHY interface mode. While this works at present, there are cases where this is sub-optimal. For example, where a module can operate with several different PHY interface modes. To start addressing this, arrange for the SFP EEPROM parsing to also provide a bitmap of the possible PHY interface modes. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-20net: sfp: add support for HALNy GPON SFPRussell King (Oracle)1-1/+1
Add a quirk for the HALNy HL-GSFP module, which appears to have an inverted RX_LOS signal, and maybe uses TX_FAULT as a serial port transmit pin. Rather than use these hardware signals, switch to using software polling for these status signals. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-20net: sfp: move quirk handling into sfp.cRussell King (Oracle)1-95/+3
We need to handle more quirks than just those which affect the link modes of the module. Move the quirk lookup into sfp.c, and pass the quirk to sfp-bus.c Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-15net: sfp: add 2500base-X quirk for Lantech SFP moduleMichael Walle1-0/+6
The Lantech 8330-262D-E module is 2500base-X capable, but it reports the nominal bitrate as 2500MBd instead of 3125MBd. Add a quirk for the module. The following in an EEPROM dump of such a SFP with the serial number redacted: 00: 03 04 07 00 00 00 01 20 40 0c 05 01 19 00 00 00 ???...? @????... 10: 1e 0f 00 00 4c 61 6e 74 65 63 68 20 20 20 20 20 ??..Lantech 20: 20 20 20 20 00 00 00 00 38 33 33 30 2d 32 36 32 ....8330-262 30: 44 2d 45 20 20 20 20 20 56 31 2e 30 03 52 00 cb D-E V1.0?R.? 40: 00 1a 00 00 46 43 XX XX XX XX XX XX XX XX XX XX .?..FCXXXXXXXXXX 50: 20 20 20 20 32 32 30 32 31 34 20 20 68 b0 01 98 220214 h??? 60: 45 58 54 52 45 4d 45 4c 59 20 43 4f 4d 50 41 54 EXTREMELY COMPAT 70: 49 42 4c 45 20 20 20 20 20 20 20 20 20 20 20 20 IBLE Signed-off-by: Michael Walle <michael@walle.cc> Link: https://lore.kernel.org/r/20220312205014.4154907-1-michael@walle.cc Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-01-24net: sfp: ignore disabled SFP nodeMarek Behún1-0/+5
Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") added code which finds SFP bus DT node even if the node is disabled with status = "disabled". Because of this, when phylink is created, it ends with non-null .sfp_bus member, even though the SFP module is not probed (because the node is disabled). We need to ignore disabled SFP bus node. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson1-1/+1
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-16net: phy: fix space alignment issuesWenpeng Liang1-14/+14
There are some space related issues, including spaces at the start of the line, before tabs, after open parenthesis and before close parenthesis. Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Weihang Li <liweihang@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-12net: sfp: add support for 25G BASE-R SFPsSteen Hegelund1-0/+5
Add support for 25gbase-r modules. This is needed for the Sparx5 switch. Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com> Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-11phy: sfp: add netlink SFP support to generic SFP codeAndrew Lunn1-0/+20
The new netlink API for reading SFP data requires a new op to be implemented. The idea of the new netlink SFP code is that userspace is responsible to parsing the EEPROM data and requesting pages, rather than have the kernel decide what pages are interesting and returning them. This allows greater flexibility for newer formats. Currently the generic SFP code only supports simple SFPs. Allow i2c address 0x50 and 0x51 to be accessed with page and bank must always be 0. This interface will later be extended when for example QSFP support is added. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16sfp: add support for 5gbase-t SFPsMarek Behún1-0/+3
The sfp_parse_support() function is setting 5000baseT_Full in some cases. Now that we have PHY_INTERFACE_MODE_5GBASER interface mode available, change sfp_select_interface() to return PHY_INTERFACE_MODE_5GBASER if 5000baseT_Full is set in the link mode mask. Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-01-28net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber InstantPali Rohár1-0/+15
The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information stored in its EEPROM. It claims to support all transceiver types including 10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is the only one supported. This module has also phys_id set to SFF, and the SFP subsystem currently does not allow to use SFP modules detected as SFFs. Add exception for this module so it can be detected as supported. This change finally allows to detect and use SFP GPON module Ubiquiti U-Fiber Instant on Linux system. EEPROM content of this SFP module is (where XX is serial number): 00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.?? 10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT 20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA 30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6 40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX 50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-14sfp: add support for 100 base-x SFPsBjarni Jonasson1-0/+9
Add support for 100Base-FX, 100Base-LX, 100Base-PX and 100Base-BX10 modules This is needed for Sparx-5 switch. Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-11net: sfp: extend bitrate-derived mode for 2500BASE-XRussell King1-3/+8
Extend the bitrate-derived support to include 2500BASE-X for modules that report a bitrate of 2500Mbaud. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1kyYQf-0004iY-Gh@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-09net: sfp: relax bitrate-derived mode checkRussell King1-6/+5
Do not check the encoding when deriving 1000BASE-X from the bitrate when no other modes are discovered. Some GPON modules (VSOL V2801F and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a 1200Mbaud bitrate, but should be driven with 1000BASE-X on the host side. Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva1-2/+2
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-03-17net: phy: sfp-bus.c: get rid of docs warningsMauro Carvalho Chehab1-14/+18
The indentation for the returned values are weird, causing those warnings: ./drivers/net/phy/sfp-bus.c:579: WARNING: Unexpected indentation. ./drivers/net/phy/sfp-bus.c:619: WARNING: Unexpected indentation. Use a list and change the identation for it to be properly parsed by the documentation toolchain. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKRRussell King1-1/+1
Switch network drivers, phy drivers, and SFP/phylink over to use the more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane ethernet, which is 10GBASE-R with autonegotiation on top, which our current usage on the affected platforms does not have. The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia PHY, which has a separate mode for 10GBASE-KR. For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R for compatibility with existing DT - this is the only network driver at present that makes use of PHY_INTERFACE_MODE_10GKR. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-11net: phylink: delay MAC configuration for copper SFP modulesRussell King1-0/+28
Knowing whether we need to delay the MAC configuration because a module may have a PHY is useful to phylink to allow NBASE-T modules to work on systems supporting no more than 2.5G speeds. This commit allows us to delay such configuration until after the PHY has been probed by recording the parsed capabilities, and if the module may have a PHY, doing no more until the module_start() notification is called. At that point, we either have a PHY, or we don't. We move the PHY-based setup a little later, and use the PHYs support capabilities rather than the EEPROM parsed capabilities to determine whether we can support the PHY. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-11net: sfp: add module start/stop upstream notificationsRussell King1-0/+21
When dealing with some copper modules, we can't positively know the module capabilities are until we have probed the PHY. Without the full capabilities, we may end up failing a module that we could otherwise drive with a restricted set of capabilities. An example of this would be a module with a NBASE-T PHY plugged into a host that supports phy interface modes 2500BASE-X and SGMII. The PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes, which means a subset of the capabilities are compatible with the host. However, reading the module EEPROM leads us to believe that the module only supports ethtool link mode 10GBASE-T, which is incompatible with the host - and thus results in the module being rejected. This patch adds an extra notification which are triggered after the SFP module's PHY probe, and a corresponding notification just before the PHY is removed. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-11net: sfp: add more extended compliance codesRussell King1-24/+36
SFF-8024 is used to define various constants re-used in several SFF SFP-related specifications. Split these constants from the enum, and rename them to indicate that they're defined by SFF-8024. Add and use updated SFF-8024 extended compliance code definitions for 10GBASE-T, 5GBASE-T and 2.5GBASE-T modules. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-11net: sfp: derive interface mode from ethtool link modesRussell King1-7/+4
We don't need the EEPROM ID to derive the phy interface mode as we can derive it merely from the ethtool link modes. Remove the EEPROM ID argument to sfp_select_interface(). Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-11net: sfp: remove incomplete 100BASE-FX and 100BASE-LX supportRussell King1-3/+1
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this is probably an incorrect assumption. In any case, sfp_parse_support() will fail such a module. Let's stop pretending we support these modules. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: sfp: add some quirks for GPON modulesRussell King1-0/+25
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P modules are capable of 2500base-X, but incorrectly report their capabilities in the EEPROM. It seems rather common that GPON modules mis-report. Let's fix these modules by adding some quirks. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-20net: sfp: add support for module quirksRussell King1-0/+54
Add support for applying module quirks to the list of supported ethtool link modes. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-11net: sfp: fix sfp_bus_put() kernel documentationRussell King1-1/+1
The kbuild test robot found a problem with htmldocs with the recent change to the SFP interfaces. Fix the kernel documentation for sfp_bus_put() which was missing an '@' before the argument name description. Fixes: 727b3668b730 ("net: sfp: rework upstream interface") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-09net: sfp: rework upstream interfaceRussell King1-27/+65
The current upstream interface is an all-or-nothing, which is sub-optimal for future changes, as it doesn't allow the upstream driver to prepare for the SFP module becoming available, as it is at boot. Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus interface structure instead, which allows the upstream driver to prepare for a module being available as soon as add-upstream is called. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-16net: sfp: move fwnode parsing into sfp-bus layerRussell King1-23/+42
Rather than parsing the sfp firmware node in phylink, parse it in the sfp-bus code, so we can re-use this code for PHYs without having to duplicate the parsing. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-31net: sfp: remove sfp-bus use of netdevsRussell King1-7/+3
The sfp-bus code now no longer has any use for the network device structure, so remove its use. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-31net: sfp: add mandatory attach/detach methods for sfp busesRussell King1-2/+2
Add attach and detach methods for SFP buses, which will allow us to get rid of the netdev storage in sfp-bus. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-21treewide: Add SPDX license identifier for missed filesThomas Gleixner1-0/+1
Add SPDX license identifiers to all files which: - Have no license information of any form - Have EXPORT_.*_SYMBOL_GPL inside which was used in the initial scan/conversion to ignore the file These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-08net: sfp: do not probe SFP module before we're attachedRussell King1-0/+2
When we probe a SFP module, we expect to be able to call the upstream device's module_insert() function so that the upstream link can be configured. However, when the upstream device is delayed, we currently may end up probing the module before the upstream device is available, and lose the module_insert() call. Avoid this by holding off probing the module until the SFP bus is properly connected to both the SFP socket driver and the upstream driver. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-29net: phy: sfp: correct store of detected link modesBaruch Siach1-1/+1
The link modes that sfp_parse_support() detects are stored in the 'modes' bitmap. There is no reason to make an exception for 1000Base-PX or 1000Base-BX10. Fixes: 03145864bd0f ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules") Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18sfp: fix oops with ethtool -mRussell King1-2/+2
If a network interface is created prior to the SFP socket being available, ethtool can request module information. This unfortunately leads to an oops: Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = (ptrval) [00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138 Hardware name: Broadcom Northstar Plus SoC PC is at sfp_get_module_info+0x8/0x10 LR is at dev_ethtool+0x218c/0x2afc Fix this by not filling in the network device's SFP bus pointer until SFP is fully bound, thereby avoiding the core calling into the SFP bus code. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-11sfp: fix module initialisation with netdev already upRussell King1-2/+2
It was been observed that with a particular order of initialisation, the netdev can be up, but the SFP module still has its TX_DISABLE signal asserted. This occurs when the network device brought up before the SFP kernel module has been inserted by userspace. This occurs because sfp-bus layer does not hear about the change in network device state, and so assumes that it is still down. Set netdev->sfp when the upstream is registered to work around this problem. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-11sfp: ensure we clean up properly on bus registration failureRussell King1-7/+24
We fail to correctly clean up after a bus registration failure, which can lead to an incorrect assumption about the registration state of the upstream or sfp cage. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+1
The bpf syscall and selftests conflicts were trivial overlapping changes. The r8169 change involved moving the added mdelay from 'net' into a different function. A TLS close bug fix overlapped with the splitting of the TLS state into separate TX and RX parts. I just expanded the tests in the bug fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf == X". Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-08net: phy: sfp: handle cases where neither BR, min nor BR, max is givenAntoine Tenart1-0/+7
When computing the bitrate using values read from an SFP module EEPROM, we use the nominal BR plus BR,min and BR,max to determine the boundaries. But in some cases BR,min and BR,max aren't provided, which led the SFP code to end up having the nominal value for both the minimum and maximum bitrate values. When using a passive cable, the nominal value should be used as the maximum one, and there is no minimum one so we should use 0. Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-04net: phy: sfp: fix the BR,min computationAntoine Tenart1-1/+1
In an SFP EEPROM values can be read to get information about a given SFP module. One of those is the bitrate, which can be determined using a nominal bitrate in addition with min and max values (in %). The SFP code currently compute both BR,min and BR,max values thanks to this nominal and min,max values. This patch fixes the BR,min computation as the min value should be subtracted to the nominal one, not added. Fixes: 9962acf7fb8c ("sfp: add support for 1000Base-PX and 1000Base-BX10") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-30sfp/phylink: move module EEPROM ethtool access into netdev core ethtoolRussell King1-4/+2
Provide a pointer to the SFP bus in struct net_device, so that the ethtool module EEPROM methods can access the SFP directly, rather than needing every user to provide a hook for it. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28phylink,sfp: negotiate interface format with MACRussell King1-62/+39
Negotiate the interface format with the MAC rather than requiring it to be a fixed type specified solely by the SFP module. This allows modules that can work with several different interface signalling formats to select a format compatible with the MAC - for example, a Fiber module supporing Gigabit ethernet and faster connected to a Gigabit only MAC needs to select the 1000BASE-X mode. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modulesRussell King1-23/+38
Some BiDi modules (eg, FiberStore SFP-GE-BX) are not compliant with 1000BASE-BX as they use different wavelengths from the 1000BASE-BX standard (eg, 1310nm/1550nm rather than 1310nm/1490nm). These modules support 1000BASE-X ethernet, so detect them by a failure to find any other support, the 8B10B encoding and a bit rate that falls within the 1Gbps window. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-23net: phy: sfp: Fix kernel doc warningFlorian Fainelli1-1/+1
We forgot to update the kernel doc header above sfp_register_upstream() Fixes: c19bb00070dd ("sfp: convert to fwnode") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-2/+4
2018-01-02sfp: improve support for direct-attach copper cablesRussell King1-7/+44
Improve the support for direct-attach copper so that we avoid kernel warning messages, and report the appropriate PORT_DA type to userspace. Direct Attach cables can use a number of protocols depending on their range of speeds. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02sfp: add support for 1000Base-PX and 1000Base-BX10Russell King1-0/+21
Add support for decoding the transceiver information for 1000Base-PX and 1000Base-BX10. These use 1000BASE-X protocol. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02sfp: don't guess support from connector typeRussell King1-29/+0
Don't try to guess the support mask from the connector type - this is mostly irrelevant to the speeds that the transceiver supports. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-02sfp: fix sfp-bus oops when removing socket/upstreamRussell King1-2/+4
When we remove a socket or upstream, and the other side isn't registered, we dereference a NULL pointer, causing a kernel oops. Fix this. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-05sfp: convert to fwnodeRussell King1-7/+7
Convert sfp-bus to use fwnode rather than device_node internally, so we can support more than just device tree firmware. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-05sfp: fix sparse warningRussell King1-1/+1
drivers/net/phy/sfp-bus.c:298:13: warning: context imbalance in 'sfp_bus_release' - wrong count at exit Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.